forked from Minki/linux
0d0644ebc6
mvsdio_platform_data allows to pass card detect and write protect gpio numbers to the driver. Some kirkwood boards don't use both pins as they are not connected, and don't set the corresponding value in platform_data. This will leave the unset values in platform_data initialized as 0, which is in fact a valid gpio pin. mvsdio will grab that pin and configure it as gpio, which in turn breaks nand controller as mpp0 also carries nand_io2. This patch fixes the above by initializing unused gpio functions in the platform_data with an invalid (-1) value. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Reported-by: Soeren Moch <smoch@web.de> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
127 lines
3.0 KiB
C
127 lines
3.0 KiB
C
/*
|
|
* arch/arm/mach-kirkwood/rd88f6281-setup.c
|
|
*
|
|
* Marvell RD-88F6281 Reference Board Setup
|
|
*
|
|
* This file is licensed under the terms of the GNU General Public
|
|
* License version 2. This program is licensed "as is" without any
|
|
* warranty of any kind, whether express or implied.
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/irq.h>
|
|
#include <linux/mtd/partitions.h>
|
|
#include <linux/ata_platform.h>
|
|
#include <linux/mv643xx_eth.h>
|
|
#include <linux/ethtool.h>
|
|
#include <net/dsa.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
#include <mach/kirkwood.h>
|
|
#include <linux/platform_data/mmc-mvsdio.h>
|
|
#include "common.h"
|
|
#include "mpp.h"
|
|
|
|
static struct mtd_partition rd88f6281_nand_parts[] = {
|
|
{
|
|
.name = "u-boot",
|
|
.offset = 0,
|
|
.size = SZ_1M
|
|
}, {
|
|
.name = "uImage",
|
|
.offset = MTDPART_OFS_NXTBLK,
|
|
.size = SZ_2M
|
|
}, {
|
|
.name = "root",
|
|
.offset = MTDPART_OFS_NXTBLK,
|
|
.size = MTDPART_SIZ_FULL
|
|
},
|
|
};
|
|
|
|
static struct mv643xx_eth_platform_data rd88f6281_ge00_data = {
|
|
.phy_addr = MV643XX_ETH_PHY_NONE,
|
|
.speed = SPEED_1000,
|
|
.duplex = DUPLEX_FULL,
|
|
};
|
|
|
|
static struct dsa_chip_data rd88f6281_switch_chip_data = {
|
|
.port_names[0] = "lan1",
|
|
.port_names[1] = "lan2",
|
|
.port_names[2] = "lan3",
|
|
.port_names[3] = "lan4",
|
|
.port_names[5] = "cpu",
|
|
};
|
|
|
|
static struct dsa_platform_data rd88f6281_switch_plat_data = {
|
|
.nr_chips = 1,
|
|
.chip = &rd88f6281_switch_chip_data,
|
|
};
|
|
|
|
static struct mv643xx_eth_platform_data rd88f6281_ge01_data = {
|
|
.phy_addr = MV643XX_ETH_PHY_ADDR(11),
|
|
};
|
|
|
|
static struct mv_sata_platform_data rd88f6281_sata_data = {
|
|
.n_ports = 2,
|
|
};
|
|
|
|
static struct mvsdio_platform_data rd88f6281_mvsdio_data = {
|
|
.gpio_card_detect = 28,
|
|
.gpio_write_protect = -1,
|
|
};
|
|
|
|
static unsigned int rd88f6281_mpp_config[] __initdata = {
|
|
MPP28_GPIO,
|
|
0
|
|
};
|
|
|
|
static void __init rd88f6281_init(void)
|
|
{
|
|
u32 dev, rev;
|
|
|
|
/*
|
|
* Basic setup. Needs to be called early.
|
|
*/
|
|
kirkwood_init();
|
|
kirkwood_mpp_conf(rd88f6281_mpp_config);
|
|
|
|
kirkwood_nand_init(ARRAY_AND_SIZE(rd88f6281_nand_parts), 25);
|
|
kirkwood_ehci_init();
|
|
|
|
kirkwood_ge00_init(&rd88f6281_ge00_data);
|
|
kirkwood_pcie_id(&dev, &rev);
|
|
if (rev == MV88F6281_REV_A0) {
|
|
rd88f6281_switch_chip_data.sw_addr = 10;
|
|
kirkwood_ge01_init(&rd88f6281_ge01_data);
|
|
} else {
|
|
rd88f6281_switch_chip_data.port_names[4] = "wan";
|
|
}
|
|
kirkwood_ge00_switch_init(&rd88f6281_switch_plat_data, NO_IRQ);
|
|
|
|
kirkwood_sata_init(&rd88f6281_sata_data);
|
|
kirkwood_sdio_init(&rd88f6281_mvsdio_data);
|
|
kirkwood_uart0_init();
|
|
}
|
|
|
|
static int __init rd88f6281_pci_init(void)
|
|
{
|
|
if (machine_is_rd88f6281())
|
|
kirkwood_pcie_init(KW_PCIE0);
|
|
|
|
return 0;
|
|
}
|
|
subsys_initcall(rd88f6281_pci_init);
|
|
|
|
MACHINE_START(RD88F6281, "Marvell RD-88F6281 Reference Board")
|
|
/* Maintainer: Saeed Bishara <saeed@marvell.com> */
|
|
.atag_offset = 0x100,
|
|
.init_machine = rd88f6281_init,
|
|
.map_io = kirkwood_map_io,
|
|
.init_early = kirkwood_init_early,
|
|
.init_irq = kirkwood_init_irq,
|
|
.init_time = kirkwood_timer_init,
|
|
.restart = kirkwood_restart,
|
|
MACHINE_END
|