linux/drivers/net/sky2.h
Stephen Hemminger 14d0263fea [PATCH] sky2: fragmented receive for large MTU
Use hardware support for chained receive to break up large frames
into multiple pages. This avoids having to do a mult-page allocation
that can fail on a busy system due to fragmented memory.

For normal size MTU, this code behaves the same.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-27 17:56:31 -04:00

1941 lines
72 KiB
C

/*
* Definitions for the new Marvell Yukon 2 driver.
*/
#ifndef _SKY2_H
#define _SKY2_H
#define ETH_JUMBO_MTU 9000 /* Maximum MTU supported */
/* PCI device specific config registers */
enum {
PCI_DEV_REG1 = 0x40,
PCI_DEV_REG2 = 0x44,
PCI_DEV_REG3 = 0x80,
PCI_DEV_REG4 = 0x84,
PCI_DEV_REG5 = 0x88,
};
/* Yukon-2 */
enum pci_dev_reg_1 {
PCI_Y2_PIG_ENA = 1<<31, /* Enable Plug-in-Go (YUKON-2) */
PCI_Y2_DLL_DIS = 1<<30, /* Disable PCI DLL (YUKON-2) */
PCI_Y2_PHY2_COMA = 1<<29, /* Set PHY 2 to Coma Mode (YUKON-2) */
PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */
PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */
PCI_Y2_PHY1_POWD = 1<<26, /* Set PHY 1 to Power Down (YUKON-2) */
};
enum pci_dev_reg_2 {
PCI_VPD_WR_THR = 0xffL<<24, /* Bit 31..24: VPD Write Threshold */
PCI_DEV_SEL = 0x7fL<<17, /* Bit 23..17: EEPROM Device Select */
PCI_VPD_ROM_SZ = 7L<<14, /* Bit 16..14: VPD ROM Size */
PCI_PATCH_DIR = 0xfL<<8, /* Bit 11.. 8: Ext Patches dir 3..0 */
PCI_EXT_PATCHS = 0xfL<<4, /* Bit 7.. 4: Extended Patches 3..0 */
PCI_EN_DUMMY_RD = 1<<3, /* Enable Dummy Read */
PCI_REV_DESC = 1<<2, /* Reverse Desc. Bytes */
PCI_USEDATA64 = 1<<0, /* Use 64Bit Data bus ext */
};
/* PCI_OUR_REG_4 32 bit Our Register 4 (Yukon-ECU only) */
enum pci_dev_reg_4 {
/* (Link Training & Status State Machine) */
P_TIMER_VALUE_MSK = 0xffL<<16, /* Bit 23..16: Timer Value Mask */
/* (Active State Power Management) */
P_FORCE_ASPM_REQUEST = 1<<15, /* Force ASPM Request (A1 only) */
P_ASPM_GPHY_LINK_DOWN = 1<<14, /* GPHY Link Down (A1 only) */
P_ASPM_INT_FIFO_EMPTY = 1<<13, /* Internal FIFO Empty (A1 only) */
P_ASPM_CLKRUN_REQUEST = 1<<12, /* CLKRUN Request (A1 only) */
P_ASPM_FORCE_CLKREQ_ENA = 1<<4, /* Force CLKREQ Enable (A1b only) */
P_ASPM_CLKREQ_PAD_CTL = 1<<3, /* CLKREQ PAD Control (A1 only) */
P_ASPM_A1_MODE_SELECT = 1<<2, /* A1 Mode Select (A1 only) */
P_CLK_GATE_PEX_UNIT_ENA = 1<<1, /* Enable Gate PEX Unit Clock */
P_CLK_GATE_ROOT_COR_ENA = 1<<0, /* Enable Gate Root Core Clock */
P_ASPM_CONTROL_MSK = P_FORCE_ASPM_REQUEST | P_ASPM_GPHY_LINK_DOWN
| P_ASPM_CLKRUN_REQUEST | P_ASPM_INT_FIFO_EMPTY,
};
#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
PCI_STATUS_SIG_SYSTEM_ERROR | \
PCI_STATUS_REC_MASTER_ABORT | \
PCI_STATUS_REC_TARGET_ABORT | \
PCI_STATUS_PARITY)
enum csr_regs {
B0_RAP = 0x0000,
B0_CTST = 0x0004,
B0_Y2LED = 0x0005,
B0_POWER_CTRL = 0x0007,
B0_ISRC = 0x0008,
B0_IMSK = 0x000c,
B0_HWE_ISRC = 0x0010,
B0_HWE_IMSK = 0x0014,
/* Special ISR registers (Yukon-2 only) */
B0_Y2_SP_ISRC2 = 0x001c,
B0_Y2_SP_ISRC3 = 0x0020,
B0_Y2_SP_EISR = 0x0024,
B0_Y2_SP_LISR = 0x0028,
B0_Y2_SP_ICR = 0x002c,
B2_MAC_1 = 0x0100,
B2_MAC_2 = 0x0108,
B2_MAC_3 = 0x0110,
B2_CONN_TYP = 0x0118,
B2_PMD_TYP = 0x0119,
B2_MAC_CFG = 0x011a,
B2_CHIP_ID = 0x011b,
B2_E_0 = 0x011c,
B2_Y2_CLK_GATE = 0x011d,
B2_Y2_HW_RES = 0x011e,
B2_E_3 = 0x011f,
B2_Y2_CLK_CTRL = 0x0120,
B2_TI_INI = 0x0130,
B2_TI_VAL = 0x0134,
B2_TI_CTRL = 0x0138,
B2_TI_TEST = 0x0139,
B2_TST_CTRL1 = 0x0158,
B2_TST_CTRL2 = 0x0159,
B2_GP_IO = 0x015c,
B2_I2C_CTRL = 0x0160,
B2_I2C_DATA = 0x0164,
B2_I2C_IRQ = 0x0168,
B2_I2C_SW = 0x016c,
B3_RAM_ADDR = 0x0180,
B3_RAM_DATA_LO = 0x0184,
B3_RAM_DATA_HI = 0x0188,
/* RAM Interface Registers */
/* Yukon-2: use RAM_BUFFER() to access the RAM buffer */
/*
* The HW-Spec. calls this registers Timeout Value 0..11. But this names are
* not usable in SW. Please notice these are NOT real timeouts, these are
* the number of qWords transferred continuously.
*/
#define RAM_BUFFER(port, reg) (reg | (port <<6))
B3_RI_WTO_R1 = 0x0190,
B3_RI_WTO_XA1 = 0x0191,
B3_RI_WTO_XS1 = 0x0192,
B3_RI_RTO_R1 = 0x0193,
B3_RI_RTO_XA1 = 0x0194,
B3_RI_RTO_XS1 = 0x0195,
B3_RI_WTO_R2 = 0x0196,
B3_RI_WTO_XA2 = 0x0197,
B3_RI_WTO_XS2 = 0x0198,
B3_RI_RTO_R2 = 0x0199,
B3_RI_RTO_XA2 = 0x019a,
B3_RI_RTO_XS2 = 0x019b,
B3_RI_TO_VAL = 0x019c,
B3_RI_CTRL = 0x01a0,
B3_RI_TEST = 0x01a2,
B3_MA_TOINI_RX1 = 0x01b0,
B3_MA_TOINI_RX2 = 0x01b1,
B3_MA_TOINI_TX1 = 0x01b2,
B3_MA_TOINI_TX2 = 0x01b3,
B3_MA_TOVAL_RX1 = 0x01b4,
B3_MA_TOVAL_RX2 = 0x01b5,
B3_MA_TOVAL_TX1 = 0x01b6,
B3_MA_TOVAL_TX2 = 0x01b7,
B3_MA_TO_CTRL = 0x01b8,
B3_MA_TO_TEST = 0x01ba,
B3_MA_RCINI_RX1 = 0x01c0,
B3_MA_RCINI_RX2 = 0x01c1,
B3_MA_RCINI_TX1 = 0x01c2,
B3_MA_RCINI_TX2 = 0x01c3,
B3_MA_RCVAL_RX1 = 0x01c4,
B3_MA_RCVAL_RX2 = 0x01c5,
B3_MA_RCVAL_TX1 = 0x01c6,
B3_MA_RCVAL_TX2 = 0x01c7,
B3_MA_RC_CTRL = 0x01c8,
B3_MA_RC_TEST = 0x01ca,
B3_PA_TOINI_RX1 = 0x01d0,
B3_PA_TOINI_RX2 = 0x01d4,
B3_PA_TOINI_TX1 = 0x01d8,
B3_PA_TOINI_TX2 = 0x01dc,
B3_PA_TOVAL_RX1 = 0x01e0,
B3_PA_TOVAL_RX2 = 0x01e4,
B3_PA_TOVAL_TX1 = 0x01e8,
B3_PA_TOVAL_TX2 = 0x01ec,
B3_PA_CTRL = 0x01f0,
B3_PA_TEST = 0x01f2,
Y2_CFG_SPC = 0x1c00,
};
/* B0_CTST 16 bit Control/Status register */
enum {
Y2_VMAIN_AVAIL = 1<<17,/* VMAIN available (YUKON-2 only) */
Y2_VAUX_AVAIL = 1<<16,/* VAUX available (YUKON-2 only) */
Y2_HW_WOL_ON = 1<<15,/* HW WOL On (Yukon-EC Ultra A1 only) */
Y2_HW_WOL_OFF = 1<<14,/* HW WOL On (Yukon-EC Ultra A1 only) */
Y2_ASF_ENABLE = 1<<13,/* ASF Unit Enable (YUKON-2 only) */
Y2_ASF_DISABLE = 1<<12,/* ASF Unit Disable (YUKON-2 only) */
Y2_CLK_RUN_ENA = 1<<11,/* CLK_RUN Enable (YUKON-2 only) */
Y2_CLK_RUN_DIS = 1<<10,/* CLK_RUN Disable (YUKON-2 only) */
Y2_LED_STAT_ON = 1<<9, /* Status LED On (YUKON-2 only) */
Y2_LED_STAT_OFF = 1<<8, /* Status LED Off (YUKON-2 only) */
CS_ST_SW_IRQ = 1<<7, /* Set IRQ SW Request */
CS_CL_SW_IRQ = 1<<6, /* Clear IRQ SW Request */
CS_STOP_DONE = 1<<5, /* Stop Master is finished */
CS_STOP_MAST = 1<<4, /* Command Bit to stop the master */
CS_MRST_CLR = 1<<3, /* Clear Master reset */
CS_MRST_SET = 1<<2, /* Set Master reset */
CS_RST_CLR = 1<<1, /* Clear Software reset */
CS_RST_SET = 1, /* Set Software reset */
};
/* B0_LED 8 Bit LED register */
enum {
/* Bit 7.. 2: reserved */
LED_STAT_ON = 1<<1, /* Status LED on */
LED_STAT_OFF = 1, /* Status LED off */
};
/* B0_POWER_CTRL 8 Bit Power Control reg (YUKON only) */
enum {
PC_VAUX_ENA = 1<<7, /* Switch VAUX Enable */
PC_VAUX_DIS = 1<<6, /* Switch VAUX Disable */
PC_VCC_ENA = 1<<5, /* Switch VCC Enable */
PC_VCC_DIS = 1<<4, /* Switch VCC Disable */
PC_VAUX_ON = 1<<3, /* Switch VAUX On */
PC_VAUX_OFF = 1<<2, /* Switch VAUX Off */
PC_VCC_ON = 1<<1, /* Switch VCC On */
PC_VCC_OFF = 1<<0, /* Switch VCC Off */
};
/* B2_IRQM_MSK 32 bit IRQ Moderation Mask */
/* B0_Y2_SP_ISRC2 32 bit Special Interrupt Source Reg 2 */
/* B0_Y2_SP_ISRC3 32 bit Special Interrupt Source Reg 3 */
/* B0_Y2_SP_EISR 32 bit Enter ISR Reg */
/* B0_Y2_SP_LISR 32 bit Leave ISR Reg */
enum {
Y2_IS_HW_ERR = 1<<31, /* Interrupt HW Error */
Y2_IS_STAT_BMU = 1<<30, /* Status BMU Interrupt */
Y2_IS_ASF = 1<<29, /* ASF subsystem Interrupt */
Y2_IS_POLL_CHK = 1<<27, /* Check IRQ from polling unit */
Y2_IS_TWSI_RDY = 1<<26, /* IRQ on end of TWSI Tx */
Y2_IS_IRQ_SW = 1<<25, /* SW forced IRQ */
Y2_IS_TIMINT = 1<<24, /* IRQ from Timer */
Y2_IS_IRQ_PHY2 = 1<<12, /* Interrupt from PHY 2 */
Y2_IS_IRQ_MAC2 = 1<<11, /* Interrupt from MAC 2 */
Y2_IS_CHK_RX2 = 1<<10, /* Descriptor error Rx 2 */
Y2_IS_CHK_TXS2 = 1<<9, /* Descriptor error TXS 2 */
Y2_IS_CHK_TXA2 = 1<<8, /* Descriptor error TXA 2 */
Y2_IS_IRQ_PHY1 = 1<<4, /* Interrupt from PHY 1 */
Y2_IS_IRQ_MAC1 = 1<<3, /* Interrupt from MAC 1 */
Y2_IS_CHK_RX1 = 1<<2, /* Descriptor error Rx 1 */
Y2_IS_CHK_TXS1 = 1<<1, /* Descriptor error TXS 1 */
Y2_IS_CHK_TXA1 = 1<<0, /* Descriptor error TXA 1 */
Y2_IS_BASE = Y2_IS_HW_ERR | Y2_IS_STAT_BMU,
Y2_IS_PORT_1 = Y2_IS_IRQ_PHY1 | Y2_IS_IRQ_MAC1
| Y2_IS_CHK_TXA1 | Y2_IS_CHK_RX1,
Y2_IS_PORT_2 = Y2_IS_IRQ_PHY2 | Y2_IS_IRQ_MAC2
| Y2_IS_CHK_TXA2 | Y2_IS_CHK_RX2,
};
/* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */
enum {
IS_ERR_MSK = 0x00003fff,/* All Error bits */
IS_IRQ_TIST_OV = 1<<13, /* Time Stamp Timer Overflow (YUKON only) */
IS_IRQ_SENSOR = 1<<12, /* IRQ from Sensor (YUKON only) */
IS_IRQ_MST_ERR = 1<<11, /* IRQ master error detected */
IS_IRQ_STAT = 1<<10, /* IRQ status exception */
IS_NO_STAT_M1 = 1<<9, /* No Rx Status from MAC 1 */
IS_NO_STAT_M2 = 1<<8, /* No Rx Status from MAC 2 */
IS_NO_TIST_M1 = 1<<7, /* No Time Stamp from MAC 1 */
IS_NO_TIST_M2 = 1<<6, /* No Time Stamp from MAC 2 */
IS_RAM_RD_PAR = 1<<5, /* RAM Read Parity Error */
IS_RAM_WR_PAR = 1<<4, /* RAM Write Parity Error */
IS_M1_PAR_ERR = 1<<3, /* MAC 1 Parity Error */
IS_M2_PAR_ERR = 1<<2, /* MAC 2 Parity Error */
IS_R1_PAR_ERR = 1<<1, /* Queue R1 Parity Error */
IS_R2_PAR_ERR = 1<<0, /* Queue R2 Parity Error */
};
/* Hardware error interrupt mask for Yukon 2 */
enum {
Y2_IS_TIST_OV = 1<<29,/* Time Stamp Timer overflow interrupt */
Y2_IS_SENSOR = 1<<28, /* Sensor interrupt */
Y2_IS_MST_ERR = 1<<27, /* Master error interrupt */
Y2_IS_IRQ_STAT = 1<<26, /* Status exception interrupt */
Y2_IS_PCI_EXP = 1<<25, /* PCI-Express interrupt */
Y2_IS_PCI_NEXP = 1<<24, /* PCI-Express error similar to PCI error */
/* Link 2 */
Y2_IS_PAR_RD2 = 1<<13, /* Read RAM parity error interrupt */
Y2_IS_PAR_WR2 = 1<<12, /* Write RAM parity error interrupt */
Y2_IS_PAR_MAC2 = 1<<11, /* MAC hardware fault interrupt */
Y2_IS_PAR_RX2 = 1<<10, /* Parity Error Rx Queue 2 */
Y2_IS_TCP_TXS2 = 1<<9, /* TCP length mismatch sync Tx queue IRQ */
Y2_IS_TCP_TXA2 = 1<<8, /* TCP length mismatch async Tx queue IRQ */
/* Link 1 */
Y2_IS_PAR_RD1 = 1<<5, /* Read RAM parity error interrupt */
Y2_IS_PAR_WR1 = 1<<4, /* Write RAM parity error interrupt */
Y2_IS_PAR_MAC1 = 1<<3, /* MAC hardware fault interrupt */
Y2_IS_PAR_RX1 = 1<<2, /* Parity Error Rx Queue 1 */
Y2_IS_TCP_TXS1 = 1<<1, /* TCP length mismatch sync Tx queue IRQ */
Y2_IS_TCP_TXA1 = 1<<0, /* TCP length mismatch async Tx queue IRQ */
Y2_HWE_L1_MASK = Y2_IS_PAR_RD1 | Y2_IS_PAR_WR1 | Y2_IS_PAR_MAC1 |
Y2_IS_PAR_RX1 | Y2_IS_TCP_TXS1| Y2_IS_TCP_TXA1,
Y2_HWE_L2_MASK = Y2_IS_PAR_RD2 | Y2_IS_PAR_WR2 | Y2_IS_PAR_MAC2 |
Y2_IS_PAR_RX2 | Y2_IS_TCP_TXS2| Y2_IS_TCP_TXA2,
Y2_HWE_ALL_MASK = Y2_IS_TIST_OV | Y2_IS_MST_ERR | Y2_IS_IRQ_STAT |
Y2_IS_PCI_EXP |
Y2_HWE_L1_MASK | Y2_HWE_L2_MASK,
};
/* B28_DPT_CTRL 8 bit Descriptor Poll Timer Ctrl Reg */
enum {
DPT_START = 1<<1,
DPT_STOP = 1<<0,
};
/* B2_TST_CTRL1 8 bit Test Control Register 1 */
enum {
TST_FRC_DPERR_MR = 1<<7, /* force DATAPERR on MST RD */
TST_FRC_DPERR_MW = 1<<6, /* force DATAPERR on MST WR */
TST_FRC_DPERR_TR = 1<<5, /* force DATAPERR on TRG RD */
TST_FRC_DPERR_TW = 1<<4, /* force DATAPERR on TRG WR */
TST_FRC_APERR_M = 1<<3, /* force ADDRPERR on MST */
TST_FRC_APERR_T = 1<<2, /* force ADDRPERR on TRG */
TST_CFG_WRITE_ON = 1<<1, /* Enable Config Reg WR */
TST_CFG_WRITE_OFF= 1<<0, /* Disable Config Reg WR */
};
/* B2_MAC_CFG 8 bit MAC Configuration / Chip Revision */
enum {
CFG_CHIP_R_MSK = 0xf<<4, /* Bit 7.. 4: Chip Revision */
/* Bit 3.. 2: reserved */
CFG_DIS_M2_CLK = 1<<1, /* Disable Clock for 2nd MAC */
CFG_SNG_MAC = 1<<0, /* MAC Config: 0=2 MACs / 1=1 MAC*/
};
/* B2_CHIP_ID 8 bit Chip Identification Number */
enum {
CHIP_ID_GENESIS = 0x0a, /* Chip ID for GENESIS */
CHIP_ID_YUKON = 0xb0, /* Chip ID for YUKON */
CHIP_ID_YUKON_LITE = 0xb1, /* Chip ID for YUKON-Lite (Rev. A1-A3) */
CHIP_ID_YUKON_LP = 0xb2, /* Chip ID for YUKON-LP */
CHIP_ID_YUKON_XL = 0xb3, /* Chip ID for YUKON-2 XL */
CHIP_ID_YUKON_EC_U = 0xb4, /* Chip ID for YUKON-2 EC Ultra */
CHIP_ID_YUKON_EC = 0xb6, /* Chip ID for YUKON-2 EC */
CHIP_ID_YUKON_FE = 0xb7, /* Chip ID for YUKON-2 FE */
CHIP_REV_YU_EC_A1 = 0, /* Chip Rev. for Yukon-EC A1/A0 */
CHIP_REV_YU_EC_A2 = 1, /* Chip Rev. for Yukon-EC A2 */
CHIP_REV_YU_EC_A3 = 2, /* Chip Rev. for Yukon-EC A3 */
CHIP_REV_YU_EC_U_A0 = 0,
CHIP_REV_YU_EC_U_A1 = 1,
};
/* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */
enum {
Y2_STATUS_LNK2_INAC = 1<<7, /* Status Link 2 inactive (0 = active) */
Y2_CLK_GAT_LNK2_DIS = 1<<6, /* Disable clock gating Link 2 */
Y2_COR_CLK_LNK2_DIS = 1<<5, /* Disable Core clock Link 2 */
Y2_PCI_CLK_LNK2_DIS = 1<<4, /* Disable PCI clock Link 2 */
Y2_STATUS_LNK1_INAC = 1<<3, /* Status Link 1 inactive (0 = active) */
Y2_CLK_GAT_LNK1_DIS = 1<<2, /* Disable clock gating Link 1 */
Y2_COR_CLK_LNK1_DIS = 1<<1, /* Disable Core clock Link 1 */
Y2_PCI_CLK_LNK1_DIS = 1<<0, /* Disable PCI clock Link 1 */
};
/* B2_Y2_HW_RES 8 bit HW Resources (Yukon-2 only) */
enum {
CFG_LED_MODE_MSK = 7<<2, /* Bit 4.. 2: LED Mode Mask */
CFG_LINK_2_AVAIL = 1<<1, /* Link 2 available */
CFG_LINK_1_AVAIL = 1<<0, /* Link 1 available */
};
#define CFG_LED_MODE(x) (((x) & CFG_LED_MODE_MSK) >> 2)
#define CFG_DUAL_MAC_MSK (CFG_LINK_2_AVAIL | CFG_LINK_1_AVAIL)
/* B2_Y2_CLK_CTRL 32 bit Clock Frequency Control Register (Yukon-2/EC) */
enum {
Y2_CLK_DIV_VAL_MSK = 0xff<<16,/* Bit 23..16: Clock Divisor Value */
#define Y2_CLK_DIV_VAL(x) (((x)<<16) & Y2_CLK_DIV_VAL_MSK)
Y2_CLK_DIV_VAL2_MSK = 7<<21, /* Bit 23..21: Clock Divisor Value */
Y2_CLK_SELECT2_MSK = 0x1f<<16,/* Bit 20..16: Clock Select */
#define Y2_CLK_DIV_VAL_2(x) (((x)<<21) & Y2_CLK_DIV_VAL2_MSK)
#define Y2_CLK_SEL_VAL_2(x) (((x)<<16) & Y2_CLK_SELECT2_MSK)
Y2_CLK_DIV_ENA = 1<<1, /* Enable Core Clock Division */
Y2_CLK_DIV_DIS = 1<<0, /* Disable Core Clock Division */
};
/* B2_TI_CTRL 8 bit Timer control */
/* B2_IRQM_CTRL 8 bit IRQ Moderation Timer Control */
enum {
TIM_START = 1<<2, /* Start Timer */
TIM_STOP = 1<<1, /* Stop Timer */
TIM_CLR_IRQ = 1<<0, /* Clear Timer IRQ (!IRQM) */
};
/* B2_TI_TEST 8 Bit Timer Test */
/* B2_IRQM_TEST 8 bit IRQ Moderation Timer Test */
/* B28_DPT_TST 8 bit Descriptor Poll Timer Test Reg */
enum {
TIM_T_ON = 1<<2, /* Test mode on */
TIM_T_OFF = 1<<1, /* Test mode off */
TIM_T_STEP = 1<<0, /* Test step */
};
/* B3_RAM_ADDR 32 bit RAM Address, to read or write */
/* Bit 31..19: reserved */
#define RAM_ADR_RAN 0x0007ffffL /* Bit 18.. 0: RAM Address Range */
/* RAM Interface Registers */
/* B3_RI_CTRL 16 bit RAM Interface Control Register */
enum {
RI_CLR_RD_PERR = 1<<9, /* Clear IRQ RAM Read Parity Err */
RI_CLR_WR_PERR = 1<<8, /* Clear IRQ RAM Write Parity Err*/
RI_RST_CLR = 1<<1, /* Clear RAM Interface Reset */
RI_RST_SET = 1<<0, /* Set RAM Interface Reset */
};
#define SK_RI_TO_53 36 /* RAM interface timeout */
/* Port related registers FIFO, and Arbiter */
#define SK_REG(port,reg) (((port)<<7)+(reg))
/* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */
/* TXA_ITI_INI 32 bit Tx Arb Interval Timer Init Val */
/* TXA_ITI_VAL 32 bit Tx Arb Interval Timer Value */
/* TXA_LIM_INI 32 bit Tx Arb Limit Counter Init Val */
/* TXA_LIM_VAL 32 bit Tx Arb Limit Counter Value */
#define TXA_MAX_VAL 0x00ffffffUL /* Bit 23.. 0: Max TXA Timer/Cnt Val */
/* TXA_CTRL 8 bit Tx Arbiter Control Register */
enum {
TXA_ENA_FSYNC = 1<<7, /* Enable force of sync Tx queue */
TXA_DIS_FSYNC = 1<<6, /* Disable force of sync Tx queue */
TXA_ENA_ALLOC = 1<<5, /* Enable alloc of free bandwidth */
TXA_DIS_ALLOC = 1<<4, /* Disable alloc of free bandwidth */
TXA_START_RC = 1<<3, /* Start sync Rate Control */
TXA_STOP_RC = 1<<2, /* Stop sync Rate Control */
TXA_ENA_ARB = 1<<1, /* Enable Tx Arbiter */
TXA_DIS_ARB = 1<<0, /* Disable Tx Arbiter */
};
/*
* Bank 4 - 5
*/
/* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */
enum {
TXA_ITI_INI = 0x0200,/* 32 bit Tx Arb Interval Timer Init Val*/
TXA_ITI_VAL = 0x0204,/* 32 bit Tx Arb Interval Timer Value */
TXA_LIM_INI = 0x0208,/* 32 bit Tx Arb Limit Counter Init Val */
TXA_LIM_VAL = 0x020c,/* 32 bit Tx Arb Limit Counter Value */
TXA_CTRL = 0x0210,/* 8 bit Tx Arbiter Control Register */
TXA_TEST = 0x0211,/* 8 bit Tx Arbiter Test Register */
TXA_STAT = 0x0212,/* 8 bit Tx Arbiter Status Register */
};
enum {
B6_EXT_REG = 0x0300,/* External registers (GENESIS only) */
B7_CFG_SPC = 0x0380,/* copy of the Configuration register */
B8_RQ1_REGS = 0x0400,/* Receive Queue 1 */
B8_RQ2_REGS = 0x0480,/* Receive Queue 2 */
B8_TS1_REGS = 0x0600,/* Transmit sync queue 1 */
B8_TA1_REGS = 0x0680,/* Transmit async queue 1 */
B8_TS2_REGS = 0x0700,/* Transmit sync queue 2 */
B8_TA2_REGS = 0x0780,/* Transmit sync queue 2 */
B16_RAM_REGS = 0x0800,/* RAM Buffer Registers */
};
/* Queue Register Offsets, use Q_ADDR() to access */
enum {
B8_Q_REGS = 0x0400, /* base of Queue registers */
Q_D = 0x00, /* 8*32 bit Current Descriptor */
Q_DA_L = 0x20, /* 32 bit Current Descriptor Address Low dWord */
Q_DA_H = 0x24, /* 32 bit Current Descriptor Address High dWord */
Q_AC_L = 0x28, /* 32 bit Current Address Counter Low dWord */
Q_AC_H = 0x2c, /* 32 bit Current Address Counter High dWord */
Q_BC = 0x30, /* 32 bit Current Byte Counter */
Q_CSR = 0x34, /* 32 bit BMU Control/Status Register */
Q_F = 0x38, /* 32 bit Flag Register */
Q_T1 = 0x3c, /* 32 bit Test Register 1 */
Q_T1_TR = 0x3c, /* 8 bit Test Register 1 Transfer SM */
Q_T1_WR = 0x3d, /* 8 bit Test Register 1 Write Descriptor SM */
Q_T1_RD = 0x3e, /* 8 bit Test Register 1 Read Descriptor SM */
Q_T1_SV = 0x3f, /* 8 bit Test Register 1 Supervisor SM */
Q_T2 = 0x40, /* 32 bit Test Register 2 */
Q_T3 = 0x44, /* 32 bit Test Register 3 */
/* Yukon-2 */
Q_DONE = 0x24, /* 16 bit Done Index (Yukon-2 only) */
Q_WM = 0x40, /* 16 bit FIFO Watermark */
Q_AL = 0x42, /* 8 bit FIFO Alignment */
Q_RSP = 0x44, /* 16 bit FIFO Read Shadow Pointer */
Q_RSL = 0x46, /* 8 bit FIFO Read Shadow Level */
Q_RP = 0x48, /* 8 bit FIFO Read Pointer */
Q_RL = 0x4a, /* 8 bit FIFO Read Level */
Q_WP = 0x4c, /* 8 bit FIFO Write Pointer */
Q_WSP = 0x4d, /* 8 bit FIFO Write Shadow Pointer */
Q_WL = 0x4e, /* 8 bit FIFO Write Level */
Q_WSL = 0x4f, /* 8 bit FIFO Write Shadow Level */
};
#define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs))
/* Q_F 32 bit Flag Register */
enum {
F_ALM_FULL = 1<<27, /* Rx FIFO: almost full */
F_EMPTY = 1<<27, /* Tx FIFO: empty flag */
F_FIFO_EOF = 1<<26, /* Tag (EOF Flag) bit in FIFO */
F_WM_REACHED = 1<<25, /* Watermark reached */
F_M_RX_RAM_DIS = 1<<24, /* MAC Rx RAM Read Port disable */
F_FIFO_LEVEL = 0x1fL<<16, /* Bit 23..16: # of Qwords in FIFO */
F_WATER_MARK = 0x0007ffL, /* Bit 10.. 0: Watermark */
};
/* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
enum {
Y2_B8_PREF_REGS = 0x0450,
PREF_UNIT_CTRL = 0x00, /* 32 bit Control register */
PREF_UNIT_LAST_IDX = 0x04, /* 16 bit Last Index */
PREF_UNIT_ADDR_LO = 0x08, /* 32 bit List start addr, low part */
PREF_UNIT_ADDR_HI = 0x0c, /* 32 bit List start addr, high part*/
PREF_UNIT_GET_IDX = 0x10, /* 16 bit Get Index */
PREF_UNIT_PUT_IDX = 0x14, /* 16 bit Put Index */
PREF_UNIT_FIFO_WP = 0x20, /* 8 bit FIFO write pointer */
PREF_UNIT_FIFO_RP = 0x24, /* 8 bit FIFO read pointer */
PREF_UNIT_FIFO_WM = 0x28, /* 8 bit FIFO watermark */
PREF_UNIT_FIFO_LEV = 0x2c, /* 8 bit FIFO level */
PREF_UNIT_MASK_IDX = 0x0fff,
};
#define Y2_QADDR(q,reg) (Y2_B8_PREF_REGS + (q) + (reg))
/* RAM Buffer Register Offsets */
enum {
RB_START = 0x00,/* 32 bit RAM Buffer Start Address */
RB_END = 0x04,/* 32 bit RAM Buffer End Address */
RB_WP = 0x08,/* 32 bit RAM Buffer Write Pointer */
RB_RP = 0x0c,/* 32 bit RAM Buffer Read Pointer */
RB_RX_UTPP = 0x10,/* 32 bit Rx Upper Threshold, Pause Packet */
RB_RX_LTPP = 0x14,/* 32 bit Rx Lower Threshold, Pause Packet */
RB_RX_UTHP = 0x18,/* 32 bit Rx Upper Threshold, High Prio */
RB_RX_LTHP = 0x1c,/* 32 bit Rx Lower Threshold, High Prio */
/* 0x10 - 0x1f: reserved at Tx RAM Buffer Registers */
RB_PC = 0x20,/* 32 bit RAM Buffer Packet Counter */
RB_LEV = 0x24,/* 32 bit RAM Buffer Level Register */
RB_CTRL = 0x28,/* 32 bit RAM Buffer Control Register */
RB_TST1 = 0x29,/* 8 bit RAM Buffer Test Register 1 */
RB_TST2 = 0x2a,/* 8 bit RAM Buffer Test Register 2 */
};
/* Receive and Transmit Queues */
enum {
Q_R1 = 0x0000, /* Receive Queue 1 */
Q_R2 = 0x0080, /* Receive Queue 2 */
Q_XS1 = 0x0200, /* Synchronous Transmit Queue 1 */
Q_XA1 = 0x0280, /* Asynchronous Transmit Queue 1 */
Q_XS2 = 0x0300, /* Synchronous Transmit Queue 2 */
Q_XA2 = 0x0380, /* Asynchronous Transmit Queue 2 */
};
/* Different PHY Types */
enum {
PHY_ADDR_MARV = 0,
};
#define RB_ADDR(offs, queue) (B16_RAM_REGS + (queue) + (offs))
enum {
LNK_SYNC_INI = 0x0c30,/* 32 bit Link Sync Cnt Init Value */
LNK_SYNC_VAL = 0x0c34,/* 32 bit Link Sync Cnt Current Value */
LNK_SYNC_CTRL = 0x0c38,/* 8 bit Link Sync Cnt Control Register */
LNK_SYNC_TST = 0x0c39,/* 8 bit Link Sync Cnt Test Register */
LNK_LED_REG = 0x0c3c,/* 8 bit Link LED Register */
/* Receive GMAC FIFO (YUKON and Yukon-2) */
RX_GMF_EA = 0x0c40,/* 32 bit Rx GMAC FIFO End Address */
RX_GMF_AF_THR = 0x0c44,/* 32 bit Rx GMAC FIFO Almost Full Thresh. */
RX_GMF_CTRL_T = 0x0c48,/* 32 bit Rx GMAC FIFO Control/Test */
RX_GMF_FL_MSK = 0x0c4c,/* 32 bit Rx GMAC FIFO Flush Mask */
RX_GMF_FL_THR = 0x0c50,/* 32 bit Rx GMAC FIFO Flush Threshold */
RX_GMF_TR_THR = 0x0c54,/* 32 bit Rx Truncation Threshold (Yukon-2) */
RX_GMF_UP_THR = 0x0c58,/* 8 bit Rx Upper Pause Thr (Yukon-EC_U) */
RX_GMF_LP_THR = 0x0c5a,/* 8 bit Rx Lower Pause Thr (Yukon-EC_U) */
RX_GMF_VLAN = 0x0c5c,/* 32 bit Rx VLAN Type Register (Yukon-2) */
RX_GMF_WP = 0x0c60,/* 32 bit Rx GMAC FIFO Write Pointer */
RX_GMF_WLEV = 0x0c68,/* 32 bit Rx GMAC FIFO Write Level */
RX_GMF_RP = 0x0c70,/* 32 bit Rx GMAC FIFO Read Pointer */
RX_GMF_RLEV = 0x0c78,/* 32 bit Rx GMAC FIFO Read Level */
};
/* Q_BC 32 bit Current Byte Counter */
/* BMU Control Status Registers */
/* B0_R1_CSR 32 bit BMU Ctrl/Stat Rx Queue 1 */
/* B0_R2_CSR 32 bit BMU Ctrl/Stat Rx Queue 2 */
/* B0_XA1_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 1 */
/* B0_XS1_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 1 */
/* B0_XA2_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 2 */
/* B0_XS2_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 2 */
/* Q_CSR 32 bit BMU Control/Status Register */
/* Rx BMU Control / Status Registers (Yukon-2) */
enum {
BMU_IDLE = 1<<31, /* BMU Idle State */
BMU_RX_TCP_PKT = 1<<30, /* Rx TCP Packet (when RSS Hash enabled) */
BMU_RX_IP_PKT = 1<<29, /* Rx IP Packet (when RSS Hash enabled) */
BMU_ENA_RX_RSS_HASH = 1<<15, /* Enable Rx RSS Hash */
BMU_DIS_RX_RSS_HASH = 1<<14, /* Disable Rx RSS Hash */
BMU_ENA_RX_CHKSUM = 1<<13, /* Enable Rx TCP/IP Checksum Check */
BMU_DIS_RX_CHKSUM = 1<<12, /* Disable Rx TCP/IP Checksum Check */
BMU_CLR_IRQ_PAR = 1<<11, /* Clear IRQ on Parity errors (Rx) */
BMU_CLR_IRQ_TCP = 1<<11, /* Clear IRQ on TCP segment. error (Tx) */
BMU_CLR_IRQ_CHK = 1<<10, /* Clear IRQ Check */
BMU_STOP = 1<<9, /* Stop Rx/Tx Queue */
BMU_START = 1<<8, /* Start Rx/Tx Queue */
BMU_FIFO_OP_ON = 1<<7, /* FIFO Operational On */
BMU_FIFO_OP_OFF = 1<<6, /* FIFO Operational Off */
BMU_FIFO_ENA = 1<<5, /* Enable FIFO */
BMU_FIFO_RST = 1<<4, /* Reset FIFO */
BMU_OP_ON = 1<<3, /* BMU Operational On */
BMU_OP_OFF = 1<<2, /* BMU Operational Off */
BMU_RST_CLR = 1<<1, /* Clear BMU Reset (Enable) */
BMU_RST_SET = 1<<0, /* Set BMU Reset */
BMU_CLR_RESET = BMU_FIFO_RST | BMU_OP_OFF | BMU_RST_CLR,
BMU_OPER_INIT = BMU_CLR_IRQ_PAR | BMU_CLR_IRQ_CHK | BMU_START |
BMU_FIFO_ENA | BMU_OP_ON,
BMU_WM_DEFAULT = 0x600,
};
/* Tx BMU Control / Status Registers (Yukon-2) */
/* Bit 31: same as for Rx */
enum {
BMU_TX_IPIDINCR_ON = 1<<13, /* Enable IP ID Increment */
BMU_TX_IPIDINCR_OFF = 1<<12, /* Disable IP ID Increment */
BMU_TX_CLR_IRQ_TCP = 1<<11, /* Clear IRQ on TCP segment length mismatch */
};
/* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
/* PREF_UNIT_CTRL 32 bit Prefetch Control register */
enum {
PREF_UNIT_OP_ON = 1<<3, /* prefetch unit operational */
PREF_UNIT_OP_OFF = 1<<2, /* prefetch unit not operational */
PREF_UNIT_RST_CLR = 1<<1, /* Clear Prefetch Unit Reset */
PREF_UNIT_RST_SET = 1<<0, /* Set Prefetch Unit Reset */
};
/* RAM Buffer Register Offsets, use RB_ADDR(Queue, Offs) to access */
/* RB_START 32 bit RAM Buffer Start Address */
/* RB_END 32 bit RAM Buffer End Address */
/* RB_WP 32 bit RAM Buffer Write Pointer */
/* RB_RP 32 bit RAM Buffer Read Pointer */
/* RB_RX_UTPP 32 bit Rx Upper Threshold, Pause Pack */
/* RB_RX_LTPP 32 bit Rx Lower Threshold, Pause Pack */
/* RB_RX_UTHP 32 bit Rx Upper Threshold, High Prio */
/* RB_RX_LTHP 32 bit Rx Lower Threshold, High Prio */
/* RB_PC 32 bit RAM Buffer Packet Counter */
/* RB_LEV 32 bit RAM Buffer Level Register */
#define RB_MSK 0x0007ffff /* Bit 18.. 0: RAM Buffer Pointer Bits */
/* RB_TST2 8 bit RAM Buffer Test Register 2 */
/* RB_TST1 8 bit RAM Buffer Test Register 1 */
/* RB_CTRL 8 bit RAM Buffer Control Register */
enum {
RB_ENA_STFWD = 1<<5, /* Enable Store & Forward */
RB_DIS_STFWD = 1<<4, /* Disable Store & Forward */
RB_ENA_OP_MD = 1<<3, /* Enable Operation Mode */
RB_DIS_OP_MD = 1<<2, /* Disable Operation Mode */
RB_RST_CLR = 1<<1, /* Clear RAM Buf STM Reset */
RB_RST_SET = 1<<0, /* Set RAM Buf STM Reset */
};
/* Transmit GMAC FIFO (YUKON only) */
enum {
TX_GMF_EA = 0x0d40,/* 32 bit Tx GMAC FIFO End Address */
TX_GMF_AE_THR = 0x0d44,/* 32 bit Tx GMAC FIFO Almost Empty Thresh.*/
TX_GMF_CTRL_T = 0x0d48,/* 32 bit Tx GMAC FIFO Control/Test */
TX_GMF_WP = 0x0d60,/* 32 bit Tx GMAC FIFO Write Pointer */
TX_GMF_WSP = 0x0d64,/* 32 bit Tx GMAC FIFO Write Shadow Ptr. */
TX_GMF_WLEV = 0x0d68,/* 32 bit Tx GMAC FIFO Write Level */
TX_GMF_RP = 0x0d70,/* 32 bit Tx GMAC FIFO Read Pointer */
TX_GMF_RSTP = 0x0d74,/* 32 bit Tx GMAC FIFO Restart Pointer */
TX_GMF_RLEV = 0x0d78,/* 32 bit Tx GMAC FIFO Read Level */
};
/* Descriptor Poll Timer Registers */
enum {
B28_DPT_INI = 0x0e00,/* 24 bit Descriptor Poll Timer Init Val */
B28_DPT_VAL = 0x0e04,/* 24 bit Descriptor Poll Timer Curr Val */
B28_DPT_CTRL = 0x0e08,/* 8 bit Descriptor Poll Timer Ctrl Reg */
B28_DPT_TST = 0x0e0a,/* 8 bit Descriptor Poll Timer Test Reg */
};
/* Time Stamp Timer Registers (YUKON only) */
enum {
GMAC_TI_ST_VAL = 0x0e14,/* 32 bit Time Stamp Timer Curr Val */
GMAC_TI_ST_CTRL = 0x0e18,/* 8 bit Time Stamp Timer Ctrl Reg */
GMAC_TI_ST_TST = 0x0e1a,/* 8 bit Time Stamp Timer Test Reg */
};
/* Polling Unit Registers (Yukon-2 only) */
enum {
POLL_CTRL = 0x0e20, /* 32 bit Polling Unit Control Reg */
POLL_LAST_IDX = 0x0e24,/* 16 bit Polling Unit List Last Index */
POLL_LIST_ADDR_LO= 0x0e28,/* 32 bit Poll. List Start Addr (low) */
POLL_LIST_ADDR_HI= 0x0e2c,/* 32 bit Poll. List Start Addr (high) */
};
/* ASF Subsystem Registers (Yukon-2 only) */
enum {
B28_Y2_SMB_CONFIG = 0x0e40,/* 32 bit ASF SMBus Config Register */
B28_Y2_SMB_CSD_REG = 0x0e44,/* 32 bit ASF SMB Control/Status/Data */
B28_Y2_ASF_IRQ_V_BASE=0x0e60,/* 32 bit ASF IRQ Vector Base */
B28_Y2_ASF_STAT_CMD= 0x0e68,/* 32 bit ASF Status and Command Reg */
B28_Y2_ASF_HOST_COM= 0x0e6c,/* 32 bit ASF Host Communication Reg */
B28_Y2_DATA_REG_1 = 0x0e70,/* 32 bit ASF/Host Data Register 1 */
B28_Y2_DATA_REG_2 = 0x0e74,/* 32 bit ASF/Host Data Register 2 */
B28_Y2_DATA_REG_3 = 0x0e78,/* 32 bit ASF/Host Data Register 3 */
B28_Y2_DATA_REG_4 = 0x0e7c,/* 32 bit ASF/Host Data Register 4 */
};
/* Status BMU Registers (Yukon-2 only)*/
enum {
STAT_CTRL = 0x0e80,/* 32 bit Status BMU Control Reg */
STAT_LAST_IDX = 0x0e84,/* 16 bit Status BMU Last Index */
STAT_LIST_ADDR_LO= 0x0e88,/* 32 bit Status List Start Addr (low) */
STAT_LIST_ADDR_HI= 0x0e8c,/* 32 bit Status List Start Addr (high) */
STAT_TXA1_RIDX = 0x0e90,/* 16 bit Status TxA1 Report Index Reg */
STAT_TXS1_RIDX = 0x0e92,/* 16 bit Status TxS1 Report Index Reg */
STAT_TXA2_RIDX = 0x0e94,/* 16 bit Status TxA2 Report Index Reg */
STAT_TXS2_RIDX = 0x0e96,/* 16 bit Status TxS2 Report Index Reg */
STAT_TX_IDX_TH = 0x0e98,/* 16 bit Status Tx Index Threshold Reg */
STAT_PUT_IDX = 0x0e9c,/* 16 bit Status Put Index Reg */
/* FIFO Control/Status Registers (Yukon-2 only)*/
STAT_FIFO_WP = 0x0ea0,/* 8 bit Status FIFO Write Pointer Reg */
STAT_FIFO_RP = 0x0ea4,/* 8 bit Status FIFO Read Pointer Reg */
STAT_FIFO_RSP = 0x0ea6,/* 8 bit Status FIFO Read Shadow Ptr */
STAT_FIFO_LEVEL = 0x0ea8,/* 8 bit Status FIFO Level Reg */
STAT_FIFO_SHLVL = 0x0eaa,/* 8 bit Status FIFO Shadow Level Reg */
STAT_FIFO_WM = 0x0eac,/* 8 bit Status FIFO Watermark Reg */
STAT_FIFO_ISR_WM= 0x0ead,/* 8 bit Status FIFO ISR Watermark Reg */
/* Level and ISR Timer Registers (Yukon-2 only)*/
STAT_LEV_TIMER_INI= 0x0eb0,/* 32 bit Level Timer Init. Value Reg */
STAT_LEV_TIMER_CNT= 0x0eb4,/* 32 bit Level Timer Counter Reg */
STAT_LEV_TIMER_CTRL= 0x0eb8,/* 8 bit Level Timer Control Reg */
STAT_LEV_TIMER_TEST= 0x0eb9,/* 8 bit Level Timer Test Reg */
STAT_TX_TIMER_INI = 0x0ec0,/* 32 bit Tx Timer Init. Value Reg */
STAT_TX_TIMER_CNT = 0x0ec4,/* 32 bit Tx Timer Counter Reg */
STAT_TX_TIMER_CTRL = 0x0ec8,/* 8 bit Tx Timer Control Reg */
STAT_TX_TIMER_TEST = 0x0ec9,/* 8 bit Tx Timer Test Reg */
STAT_ISR_TIMER_INI = 0x0ed0,/* 32 bit ISR Timer Init. Value Reg */
STAT_ISR_TIMER_CNT = 0x0ed4,/* 32 bit ISR Timer Counter Reg */
STAT_ISR_TIMER_CTRL= 0x0ed8,/* 8 bit ISR Timer Control Reg */
STAT_ISR_TIMER_TEST= 0x0ed9,/* 8 bit ISR Timer Test Reg */
};
enum {
LINKLED_OFF = 0x01,
LINKLED_ON = 0x02,
LINKLED_LINKSYNC_OFF = 0x04,
LINKLED_LINKSYNC_ON = 0x08,
LINKLED_BLINK_OFF = 0x10,
LINKLED_BLINK_ON = 0x20,
};
/* GMAC and GPHY Control Registers (YUKON only) */
enum {
GMAC_CTRL = 0x0f00,/* 32 bit GMAC Control Reg */
GPHY_CTRL = 0x0f04,/* 32 bit GPHY Control Reg */
GMAC_IRQ_SRC = 0x0f08,/* 8 bit GMAC Interrupt Source Reg */
GMAC_IRQ_MSK = 0x0f0c,/* 8 bit GMAC Interrupt Mask Reg */
GMAC_LINK_CTRL = 0x0f10,/* 16 bit Link Control Reg */
/* Wake-up Frame Pattern Match Control Registers (YUKON only) */
WOL_REG_OFFS = 0x20,/* HW-Bug: Address is + 0x20 against spec. */
WOL_CTRL_STAT = 0x0f20,/* 16 bit WOL Control/Status Reg */
WOL_MATCH_CTL = 0x0f22,/* 8 bit WOL Match Control Reg */
WOL_MATCH_RES = 0x0f23,/* 8 bit WOL Match Result Reg */
WOL_MAC_ADDR = 0x0f24,/* 32 bit WOL MAC Address */
WOL_PATT_PME = 0x0f2a,/* 8 bit WOL PME Match Enable (Yukon-2) */
WOL_PATT_ASFM = 0x0f2b,/* 8 bit WOL ASF Match Enable (Yukon-2) */
WOL_PATT_RPTR = 0x0f2c,/* 8 bit WOL Pattern Read Pointer */
/* WOL Pattern Length Registers (YUKON only) */
WOL_PATT_LEN_LO = 0x0f30,/* 32 bit WOL Pattern Length 3..0 */
WOL_PATT_LEN_HI = 0x0f34,/* 24 bit WOL Pattern Length 6..4 */
/* WOL Pattern Counter Registers (YUKON only) */
WOL_PATT_CNT_0 = 0x0f38,/* 32 bit WOL Pattern Counter 3..0 */
WOL_PATT_CNT_4 = 0x0f3c,/* 24 bit WOL Pattern Counter 6..4 */
};
enum {
WOL_PATT_RAM_1 = 0x1000,/* WOL Pattern RAM Link 1 */
WOL_PATT_RAM_2 = 0x1400,/* WOL Pattern RAM Link 2 */
};
enum {
BASE_GMAC_1 = 0x2800,/* GMAC 1 registers */
BASE_GMAC_2 = 0x3800,/* GMAC 2 registers */
};
/*
* Marvel-PHY Registers, indirect addressed over GMAC
*/
enum {
PHY_MARV_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
PHY_MARV_STAT = 0x01,/* 16 bit r/o PHY Status Register */
PHY_MARV_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
PHY_MARV_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
PHY_MARV_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
PHY_MARV_AUNE_LP = 0x05,/* 16 bit r/o Link Part Ability Reg */
PHY_MARV_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
PHY_MARV_NEPG = 0x07,/* 16 bit r/w Next Page Register */
PHY_MARV_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
/* Marvel-specific registers */
PHY_MARV_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */
PHY_MARV_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
PHY_MARV_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Reg */
PHY_MARV_PHY_CTRL = 0x10,/* 16 bit r/w PHY Specific Ctrl Reg */
PHY_MARV_PHY_STAT = 0x11,/* 16 bit r/o PHY Specific Stat Reg */
PHY_MARV_INT_MASK = 0x12,/* 16 bit r/w Interrupt Mask Reg */
PHY_MARV_INT_STAT = 0x13,/* 16 bit r/o Interrupt Status Reg */
PHY_MARV_EXT_CTRL = 0x14,/* 16 bit r/w Ext. PHY Specific Ctrl */
PHY_MARV_RXE_CNT = 0x15,/* 16 bit r/w Receive Error Counter */
PHY_MARV_EXT_ADR = 0x16,/* 16 bit r/w Ext. Ad. for Cable Diag. */
PHY_MARV_PORT_IRQ = 0x17,/* 16 bit r/o Port 0 IRQ (88E1111 only) */
PHY_MARV_LED_CTRL = 0x18,/* 16 bit r/w LED Control Reg */
PHY_MARV_LED_OVER = 0x19,/* 16 bit r/w Manual LED Override Reg */
PHY_MARV_EXT_CTRL_2 = 0x1a,/* 16 bit r/w Ext. PHY Specific Ctrl 2 */
PHY_MARV_EXT_P_STAT = 0x1b,/* 16 bit r/w Ext. PHY Spec. Stat Reg */
PHY_MARV_CABLE_DIAG = 0x1c,/* 16 bit r/o Cable Diagnostic Reg */
PHY_MARV_PAGE_ADDR = 0x1d,/* 16 bit r/w Extended Page Address Reg */
PHY_MARV_PAGE_DATA = 0x1e,/* 16 bit r/w Extended Page Data Reg */
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
PHY_MARV_FE_LED_PAR = 0x16,/* 16 bit r/w LED Parallel Select Reg. */
PHY_MARV_FE_LED_SER = 0x17,/* 16 bit r/w LED Stream Select S. LED */
PHY_MARV_FE_VCT_TX = 0x1a,/* 16 bit r/w VCT Reg. for TXP/N Pins */
PHY_MARV_FE_VCT_RX = 0x1b,/* 16 bit r/o VCT Reg. for RXP/N Pins */
PHY_MARV_FE_SPEC_2 = 0x1c,/* 16 bit r/w Specific Control Reg. 2 */
};
enum {
PHY_CT_RESET = 1<<15, /* Bit 15: (sc) clear all PHY related regs */
PHY_CT_LOOP = 1<<14, /* Bit 14: enable Loopback over PHY */
PHY_CT_SPS_LSB = 1<<13, /* Bit 13: Speed select, lower bit */
PHY_CT_ANE = 1<<12, /* Bit 12: Auto-Negotiation Enabled */
PHY_CT_PDOWN = 1<<11, /* Bit 11: Power Down Mode */
PHY_CT_ISOL = 1<<10, /* Bit 10: Isolate Mode */
PHY_CT_RE_CFG = 1<<9, /* Bit 9: (sc) Restart Auto-Negotiation */
PHY_CT_DUP_MD = 1<<8, /* Bit 8: Duplex Mode */
PHY_CT_COL_TST = 1<<7, /* Bit 7: Collision Test enabled */
PHY_CT_SPS_MSB = 1<<6, /* Bit 6: Speed select, upper bit */
};
enum {
PHY_CT_SP1000 = PHY_CT_SPS_MSB, /* enable speed of 1000 Mbps */
PHY_CT_SP100 = PHY_CT_SPS_LSB, /* enable speed of 100 Mbps */
PHY_CT_SP10 = 0, /* enable speed of 10 Mbps */
};
enum {
PHY_ST_EXT_ST = 1<<8, /* Bit 8: Extended Status Present */
PHY_ST_PRE_SUP = 1<<6, /* Bit 6: Preamble Suppression */
PHY_ST_AN_OVER = 1<<5, /* Bit 5: Auto-Negotiation Over */
PHY_ST_REM_FLT = 1<<4, /* Bit 4: Remote Fault Condition Occured */
PHY_ST_AN_CAP = 1<<3, /* Bit 3: Auto-Negotiation Capability */
PHY_ST_LSYNC = 1<<2, /* Bit 2: Link Synchronized */
PHY_ST_JAB_DET = 1<<1, /* Bit 1: Jabber Detected */
PHY_ST_EXT_REG = 1<<0, /* Bit 0: Extended Register available */
};
enum {
PHY_I1_OUI_MSK = 0x3f<<10, /* Bit 15..10: Organization Unique ID */
PHY_I1_MOD_NUM = 0x3f<<4, /* Bit 9.. 4: Model Number */
PHY_I1_REV_MSK = 0xf, /* Bit 3.. 0: Revision Number */
};
/* different Marvell PHY Ids */
enum {
PHY_MARV_ID0_VAL= 0x0141, /* Marvell Unique Identifier */
PHY_BCOM_ID1_A1 = 0x6041,
PHY_BCOM_ID1_B2 = 0x6043,
PHY_BCOM_ID1_C0 = 0x6044,
PHY_BCOM_ID1_C5 = 0x6047,
PHY_MARV_ID1_B0 = 0x0C23, /* Yukon (PHY 88E1011) */
PHY_MARV_ID1_B2 = 0x0C25, /* Yukon-Plus (PHY 88E1011) */
PHY_MARV_ID1_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */
PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */
PHY_MARV_ID1_FE = 0x0C83, /* Yukon-FE (PHY 88E3082 Rev.A1) */
PHY_MARV_ID1_ECU= 0x0CB0, /* Yukon-ECU (PHY 88E1149 Rev.B2?) */
};
/* Advertisement register bits */
enum {
PHY_AN_NXT_PG = 1<<15, /* Bit 15: Request Next Page */
PHY_AN_ACK = 1<<14, /* Bit 14: (ro) Acknowledge Received */
PHY_AN_RF = 1<<13, /* Bit 13: Remote Fault Bits */
PHY_AN_PAUSE_ASYM = 1<<11,/* Bit 11: Try for asymmetric */
PHY_AN_PAUSE_CAP = 1<<10, /* Bit 10: Try for pause */
PHY_AN_100BASE4 = 1<<9, /* Bit 9: Try for 100mbps 4k packets */
PHY_AN_100FULL = 1<<8, /* Bit 8: Try for 100mbps full-duplex */
PHY_AN_100HALF = 1<<7, /* Bit 7: Try for 100mbps half-duplex */
PHY_AN_10FULL = 1<<6, /* Bit 6: Try for 10mbps full-duplex */
PHY_AN_10HALF = 1<<5, /* Bit 5: Try for 10mbps half-duplex */
PHY_AN_CSMA = 1<<0, /* Bit 0: Only selector supported */
PHY_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
PHY_AN_FULL = PHY_AN_100FULL | PHY_AN_10FULL | PHY_AN_CSMA,
PHY_AN_ALL = PHY_AN_10HALF | PHY_AN_10FULL |
PHY_AN_100HALF | PHY_AN_100FULL,
};
/***** PHY_BCOM_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
/***** PHY_MARV_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
enum {
PHY_B_1000S_MSF = 1<<15, /* Bit 15: Master/Slave Fault */
PHY_B_1000S_MSR = 1<<14, /* Bit 14: Master/Slave Result */
PHY_B_1000S_LRS = 1<<13, /* Bit 13: Local Receiver Status */
PHY_B_1000S_RRS = 1<<12, /* Bit 12: Remote Receiver Status */
PHY_B_1000S_LP_FD = 1<<11, /* Bit 11: Link Partner can FD */
PHY_B_1000S_LP_HD = 1<<10, /* Bit 10: Link Partner can HD */
/* Bit 9..8: reserved */
PHY_B_1000S_IEC = 0xff, /* Bit 7..0: Idle Error Count */
};
/** Marvell-Specific */
enum {
PHY_M_AN_NXT_PG = 1<<15, /* Request Next Page */
PHY_M_AN_ACK = 1<<14, /* (ro) Acknowledge Received */
PHY_M_AN_RF = 1<<13, /* Remote Fault */
PHY_M_AN_ASP = 1<<11, /* Asymmetric Pause */
PHY_M_AN_PC = 1<<10, /* MAC Pause implemented */
PHY_M_AN_100_T4 = 1<<9, /* Not cap. 100Base-T4 (always 0) */
PHY_M_AN_100_FD = 1<<8, /* Advertise 100Base-TX Full Duplex */
PHY_M_AN_100_HD = 1<<7, /* Advertise 100Base-TX Half Duplex */
PHY_M_AN_10_FD = 1<<6, /* Advertise 10Base-TX Full Duplex */
PHY_M_AN_10_HD = 1<<5, /* Advertise 10Base-TX Half Duplex */
PHY_M_AN_SEL_MSK =0x1f<<4, /* Bit 4.. 0: Selector Field Mask */
};
/* special defines for FIBER (88E1011S only) */
enum {
PHY_M_AN_ASP_X = 1<<8, /* Asymmetric Pause */
PHY_M_AN_PC_X = 1<<7, /* MAC Pause implemented */
PHY_M_AN_1000X_AHD = 1<<6, /* Advertise 10000Base-X Half Duplex */
PHY_M_AN_1000X_AFD = 1<<5, /* Advertise 10000Base-X Full Duplex */
};
/* Pause Bits (PHY_M_AN_ASP_X and PHY_M_AN_PC_X) encoding */
enum {
PHY_M_P_NO_PAUSE_X = 0<<7,/* Bit 8.. 7: no Pause Mode */
PHY_M_P_SYM_MD_X = 1<<7, /* Bit 8.. 7: symmetric Pause Mode */
PHY_M_P_ASYM_MD_X = 2<<7,/* Bit 8.. 7: asymmetric Pause Mode */
PHY_M_P_BOTH_MD_X = 3<<7,/* Bit 8.. 7: both Pause Mode */
};
/***** PHY_MARV_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
enum {
PHY_M_1000C_TEST = 7<<13,/* Bit 15..13: Test Modes */
PHY_M_1000C_MSE = 1<<12, /* Manual Master/Slave Enable */
PHY_M_1000C_MSC = 1<<11, /* M/S Configuration (1=Master) */
PHY_M_1000C_MPD = 1<<10, /* Multi-Port Device */
PHY_M_1000C_AFD = 1<<9, /* Advertise Full Duplex */
PHY_M_1000C_AHD = 1<<8, /* Advertise Half Duplex */
};
/***** PHY_MARV_PHY_CTRL 16 bit r/w PHY Specific Ctrl Reg *****/
enum {
PHY_M_PC_TX_FFD_MSK = 3<<14,/* Bit 15..14: Tx FIFO Depth Mask */
PHY_M_PC_RX_FFD_MSK = 3<<12,/* Bit 13..12: Rx FIFO Depth Mask */
PHY_M_PC_ASS_CRS_TX = 1<<11, /* Assert CRS on Transmit */
PHY_M_PC_FL_GOOD = 1<<10, /* Force Link Good */
PHY_M_PC_EN_DET_MSK = 3<<8,/* Bit 9.. 8: Energy Detect Mask */
PHY_M_PC_ENA_EXT_D = 1<<7, /* Enable Ext. Distance (10BT) */
PHY_M_PC_MDIX_MSK = 3<<5,/* Bit 6.. 5: MDI/MDIX Config. Mask */
PHY_M_PC_DIS_125CLK = 1<<4, /* Disable 125 CLK */
PHY_M_PC_MAC_POW_UP = 1<<3, /* MAC Power up */
PHY_M_PC_SQE_T_ENA = 1<<2, /* SQE Test Enabled */
PHY_M_PC_POL_R_DIS = 1<<1, /* Polarity Reversal Disabled */
PHY_M_PC_DIS_JABBER = 1<<0, /* Disable Jabber */
};
enum {
PHY_M_PC_EN_DET = 2<<8, /* Energy Detect (Mode 1) */
PHY_M_PC_EN_DET_PLUS = 3<<8, /* Energy Detect Plus (Mode 2) */
};
#define PHY_M_PC_MDI_XMODE(x) (((x)<<5) & PHY_M_PC_MDIX_MSK)
enum {
PHY_M_PC_MAN_MDI = 0, /* 00 = Manual MDI configuration */
PHY_M_PC_MAN_MDIX = 1, /* 01 = Manual MDIX configuration */
PHY_M_PC_ENA_AUTO = 3, /* 11 = Enable Automatic Crossover */
};
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
enum {
PHY_M_PC_ENA_DTE_DT = 1<<15, /* Enable Data Terminal Equ. (DTE) Detect */
PHY_M_PC_ENA_ENE_DT = 1<<14, /* Enable Energy Detect (sense & pulse) */
PHY_M_PC_DIS_NLP_CK = 1<<13, /* Disable Normal Link Puls (NLP) Check */
PHY_M_PC_ENA_LIP_NP = 1<<12, /* Enable Link Partner Next Page Reg. */
PHY_M_PC_DIS_NLP_GN = 1<<11, /* Disable Normal Link Puls Generation */
PHY_M_PC_DIS_SCRAMB = 1<<9, /* Disable Scrambler */
PHY_M_PC_DIS_FEFI = 1<<8, /* Disable Far End Fault Indic. (FEFI) */
PHY_M_PC_SH_TP_SEL = 1<<6, /* Shielded Twisted Pair Select */
PHY_M_PC_RX_FD_MSK = 3<<2,/* Bit 3.. 2: Rx FIFO Depth Mask */
};
/***** PHY_MARV_PHY_STAT 16 bit r/o PHY Specific Status Reg *****/
enum {
PHY_M_PS_SPEED_MSK = 3<<14, /* Bit 15..14: Speed Mask */
PHY_M_PS_SPEED_1000 = 1<<15, /* 10 = 1000 Mbps */
PHY_M_PS_SPEED_100 = 1<<14, /* 01 = 100 Mbps */
PHY_M_PS_SPEED_10 = 0, /* 00 = 10 Mbps */
PHY_M_PS_FULL_DUP = 1<<13, /* Full Duplex */
PHY_M_PS_PAGE_REC = 1<<12, /* Page Received */
PHY_M_PS_SPDUP_RES = 1<<11, /* Speed & Duplex Resolved */
PHY_M_PS_LINK_UP = 1<<10, /* Link Up */
PHY_M_PS_CABLE_MSK = 7<<7, /* Bit 9.. 7: Cable Length Mask */
PHY_M_PS_MDI_X_STAT = 1<<6, /* MDI Crossover Stat (1=MDIX) */
PHY_M_PS_DOWNS_STAT = 1<<5, /* Downshift Status (1=downsh.) */
PHY_M_PS_ENDET_STAT = 1<<4, /* Energy Detect Status (1=act) */
PHY_M_PS_TX_P_EN = 1<<3, /* Tx Pause Enabled */
PHY_M_PS_RX_P_EN = 1<<2, /* Rx Pause Enabled */
PHY_M_PS_POL_REV = 1<<1, /* Polarity Reversed */
PHY_M_PS_JABBER = 1<<0, /* Jabber */
};
#define PHY_M_PS_PAUSE_MSK (PHY_M_PS_TX_P_EN | PHY_M_PS_RX_P_EN)
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
enum {
PHY_M_PS_DTE_DETECT = 1<<15, /* Data Terminal Equipment (DTE) Detected */
PHY_M_PS_RES_SPEED = 1<<14, /* Resolved Speed (1=100 Mbps, 0=10 Mbps */
};
enum {
PHY_M_IS_AN_ERROR = 1<<15, /* Auto-Negotiation Error */
PHY_M_IS_LSP_CHANGE = 1<<14, /* Link Speed Changed */
PHY_M_IS_DUP_CHANGE = 1<<13, /* Duplex Mode Changed */
PHY_M_IS_AN_PR = 1<<12, /* Page Received */
PHY_M_IS_AN_COMPL = 1<<11, /* Auto-Negotiation Completed */
PHY_M_IS_LST_CHANGE = 1<<10, /* Link Status Changed */
PHY_M_IS_SYMB_ERROR = 1<<9, /* Symbol Error */
PHY_M_IS_FALSE_CARR = 1<<8, /* False Carrier */
PHY_M_IS_FIFO_ERROR = 1<<7, /* FIFO Overflow/Underrun Error */
PHY_M_IS_MDI_CHANGE = 1<<6, /* MDI Crossover Changed */
PHY_M_IS_DOWNSH_DET = 1<<5, /* Downshift Detected */
PHY_M_IS_END_CHANGE = 1<<4, /* Energy Detect Changed */
PHY_M_IS_DTE_CHANGE = 1<<2, /* DTE Power Det. Status Changed */
PHY_M_IS_POL_CHANGE = 1<<1, /* Polarity Changed */
PHY_M_IS_JABBER = 1<<0, /* Jabber */
PHY_M_DEF_MSK = PHY_M_IS_LSP_CHANGE | PHY_M_IS_LST_CHANGE
| PHY_M_IS_FIFO_ERROR,
PHY_M_AN_MSK = PHY_M_IS_AN_ERROR | PHY_M_IS_AN_COMPL,
};
/***** PHY_MARV_EXT_CTRL 16 bit r/w Ext. PHY Specific Ctrl *****/
enum {
PHY_M_EC_ENA_BC_EXT = 1<<15, /* Enable Block Carr. Ext. (88E1111 only) */
PHY_M_EC_ENA_LIN_LB = 1<<14, /* Enable Line Loopback (88E1111 only) */
PHY_M_EC_DIS_LINK_P = 1<<12, /* Disable Link Pulses (88E1111 only) */
PHY_M_EC_M_DSC_MSK = 3<<10, /* Bit 11..10: Master Downshift Counter */
/* (88E1011 only) */
PHY_M_EC_S_DSC_MSK = 3<<8,/* Bit 9.. 8: Slave Downshift Counter */
/* (88E1011 only) */
PHY_M_EC_M_DSC_MSK2 = 7<<9,/* Bit 11.. 9: Master Downshift Counter */
/* (88E1111 only) */
PHY_M_EC_DOWN_S_ENA = 1<<8, /* Downshift Enable (88E1111 only) */
/* !!! Errata in spec. (1 = disable) */
PHY_M_EC_RX_TIM_CT = 1<<7, /* RGMII Rx Timing Control*/
PHY_M_EC_MAC_S_MSK = 7<<4,/* Bit 6.. 4: Def. MAC interface speed */
PHY_M_EC_FIB_AN_ENA = 1<<3, /* Fiber Auto-Neg. Enable (88E1011S only) */
PHY_M_EC_DTE_D_ENA = 1<<2, /* DTE Detect Enable (88E1111 only) */
PHY_M_EC_TX_TIM_CT = 1<<1, /* RGMII Tx Timing Control */
PHY_M_EC_TRANS_DIS = 1<<0, /* Transmitter Disable (88E1111 only) */};
#define PHY_M_EC_M_DSC(x) ((x)<<10 & PHY_M_EC_M_DSC_MSK)
/* 00=1x; 01=2x; 10=3x; 11=4x */
#define PHY_M_EC_S_DSC(x) ((x)<<8 & PHY_M_EC_S_DSC_MSK)
/* 00=dis; 01=1x; 10=2x; 11=3x */
#define PHY_M_EC_DSC_2(x) ((x)<<9 & PHY_M_EC_M_DSC_MSK2)
/* 000=1x; 001=2x; 010=3x; 011=4x */
#define PHY_M_EC_MAC_S(x) ((x)<<4 & PHY_M_EC_MAC_S_MSK)
/* 01X=0; 110=2.5; 111=25 (MHz) */
/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
enum {
PHY_M_PC_DIS_LINK_Pa = 1<<15,/* Disable Link Pulses */
PHY_M_PC_DSC_MSK = 7<<12,/* Bit 14..12: Downshift Counter */
PHY_M_PC_DOWN_S_ENA = 1<<11,/* Downshift Enable */
};
/* !!! Errata in spec. (1 = disable) */
#define PHY_M_PC_DSC(x) (((x)<<12) & PHY_M_PC_DSC_MSK)
/* 100=5x; 101=6x; 110=7x; 111=8x */
enum {
MAC_TX_CLK_0_MHZ = 2,
MAC_TX_CLK_2_5_MHZ = 6,
MAC_TX_CLK_25_MHZ = 7,
};
/***** PHY_MARV_LED_CTRL 16 bit r/w LED Control Reg *****/
enum {
PHY_M_LEDC_DIS_LED = 1<<15, /* Disable LED */
PHY_M_LEDC_PULS_MSK = 7<<12,/* Bit 14..12: Pulse Stretch Mask */
PHY_M_LEDC_F_INT = 1<<11, /* Force Interrupt */
PHY_M_LEDC_BL_R_MSK = 7<<8,/* Bit 10.. 8: Blink Rate Mask */
PHY_M_LEDC_DP_C_LSB = 1<<7, /* Duplex Control (LSB, 88E1111 only) */
PHY_M_LEDC_TX_C_LSB = 1<<6, /* Tx Control (LSB, 88E1111 only) */
PHY_M_LEDC_LK_C_MSK = 7<<3,/* Bit 5.. 3: Link Control Mask */
/* (88E1111 only) */
};
enum {
PHY_M_LEDC_LINK_MSK = 3<<3,/* Bit 4.. 3: Link Control Mask */
/* (88E1011 only) */
PHY_M_LEDC_DP_CTRL = 1<<2, /* Duplex Control */
PHY_M_LEDC_DP_C_MSB = 1<<2, /* Duplex Control (MSB, 88E1111 only) */
PHY_M_LEDC_RX_CTRL = 1<<1, /* Rx Activity / Link */
PHY_M_LEDC_TX_CTRL = 1<<0, /* Tx Activity / Link */
PHY_M_LEDC_TX_C_MSB = 1<<0, /* Tx Control (MSB, 88E1111 only) */
};
#define PHY_M_LED_PULS_DUR(x) (((x)<<12) & PHY_M_LEDC_PULS_MSK)
/***** PHY_MARV_PHY_STAT (page 3)16 bit r/w Polarity Control Reg. *****/
enum {
PHY_M_POLC_LS1M_MSK = 0xf<<12, /* Bit 15..12: LOS,STAT1 Mix % Mask */
PHY_M_POLC_IS0M_MSK = 0xf<<8, /* Bit 11.. 8: INIT,STAT0 Mix % Mask */
PHY_M_POLC_LOS_MSK = 0x3<<6, /* Bit 7.. 6: LOS Pol. Ctrl. Mask */
PHY_M_POLC_INIT_MSK = 0x3<<4, /* Bit 5.. 4: INIT Pol. Ctrl. Mask */
PHY_M_POLC_STA1_MSK = 0x3<<2, /* Bit 3.. 2: STAT1 Pol. Ctrl. Mask */
PHY_M_POLC_STA0_MSK = 0x3, /* Bit 1.. 0: STAT0 Pol. Ctrl. Mask */
};
#define PHY_M_POLC_LS1_P_MIX(x) (((x)<<12) & PHY_M_POLC_LS1M_MSK)
#define PHY_M_POLC_IS0_P_MIX(x) (((x)<<8) & PHY_M_POLC_IS0M_MSK)
#define PHY_M_POLC_LOS_CTRL(x) (((x)<<6) & PHY_M_POLC_LOS_MSK)
#define PHY_M_POLC_INIT_CTRL(x) (((x)<<4) & PHY_M_POLC_INIT_MSK)
#define PHY_M_POLC_STA1_CTRL(x) (((x)<<2) & PHY_M_POLC_STA1_MSK)
#define PHY_M_POLC_STA0_CTRL(x) (((x)<<0) & PHY_M_POLC_STA0_MSK)
enum {
PULS_NO_STR = 0,/* no pulse stretching */
PULS_21MS = 1,/* 21 ms to 42 ms */
PULS_42MS = 2,/* 42 ms to 84 ms */
PULS_84MS = 3,/* 84 ms to 170 ms */
PULS_170MS = 4,/* 170 ms to 340 ms */
PULS_340MS = 5,/* 340 ms to 670 ms */
PULS_670MS = 6,/* 670 ms to 1.3 s */
PULS_1300MS = 7,/* 1.3 s to 2.7 s */
};
#define PHY_M_LED_BLINK_RT(x) (((x)<<8) & PHY_M_LEDC_BL_R_MSK)
enum {
BLINK_42MS = 0,/* 42 ms */
BLINK_84MS = 1,/* 84 ms */
BLINK_170MS = 2,/* 170 ms */
BLINK_340MS = 3,/* 340 ms */
BLINK_670MS = 4,/* 670 ms */
};
/***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/
#define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */
/* Bit 13..12: reserved */
#define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */
#define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */
#define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */
#define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */
#define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */
#define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */
enum {
MO_LED_NORM = 0,
MO_LED_BLINK = 1,
MO_LED_OFF = 2,
MO_LED_ON = 3,
};
/***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/
enum {
PHY_M_EC2_FI_IMPED = 1<<6, /* Fiber Input Impedance */
PHY_M_EC2_FO_IMPED = 1<<5, /* Fiber Output Impedance */
PHY_M_EC2_FO_M_CLK = 1<<4, /* Fiber Mode Clock Enable */
PHY_M_EC2_FO_BOOST = 1<<3, /* Fiber Output Boost */
PHY_M_EC2_FO_AM_MSK = 7,/* Bit 2.. 0: Fiber Output Amplitude */
};
/***** PHY_MARV_EXT_P_STAT 16 bit r/w Ext. PHY Specific Status *****/
enum {
PHY_M_FC_AUTO_SEL = 1<<15, /* Fiber/Copper Auto Sel. Dis. */
PHY_M_FC_AN_REG_ACC = 1<<14, /* Fiber/Copper AN Reg. Access */
PHY_M_FC_RESOLUTION = 1<<13, /* Fiber/Copper Resolution */
PHY_M_SER_IF_AN_BP = 1<<12, /* Ser. IF AN Bypass Enable */
PHY_M_SER_IF_BP_ST = 1<<11, /* Ser. IF AN Bypass Status */
PHY_M_IRQ_POLARITY = 1<<10, /* IRQ polarity */
PHY_M_DIS_AUT_MED = 1<<9, /* Disable Aut. Medium Reg. Selection */
/* (88E1111 only) */
PHY_M_UNDOC1 = 1<<7, /* undocumented bit !! */
PHY_M_DTE_POW_STAT = 1<<4, /* DTE Power Status (88E1111 only) */
PHY_M_MODE_MASK = 0xf, /* Bit 3.. 0: copy of HWCFG MODE[3:0] */
};
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
/***** PHY_MARV_FE_LED_PAR 16 bit r/w LED Parallel Select Reg. *****/
/* Bit 15..12: reserved (used internally) */
enum {
PHY_M_FELP_LED2_MSK = 0xf<<8, /* Bit 11.. 8: LED2 Mask (LINK) */
PHY_M_FELP_LED1_MSK = 0xf<<4, /* Bit 7.. 4: LED1 Mask (ACT) */
PHY_M_FELP_LED0_MSK = 0xf, /* Bit 3.. 0: LED0 Mask (SPEED) */
};
#define PHY_M_FELP_LED2_CTRL(x) (((x)<<8) & PHY_M_FELP_LED2_MSK)
#define PHY_M_FELP_LED1_CTRL(x) (((x)<<4) & PHY_M_FELP_LED1_MSK)
#define PHY_M_FELP_LED0_CTRL(x) (((x)<<0) & PHY_M_FELP_LED0_MSK)
enum {
LED_PAR_CTRL_COLX = 0x00,
LED_PAR_CTRL_ERROR = 0x01,
LED_PAR_CTRL_DUPLEX = 0x02,
LED_PAR_CTRL_DP_COL = 0x03,
LED_PAR_CTRL_SPEED = 0x04,
LED_PAR_CTRL_LINK = 0x05,
LED_PAR_CTRL_TX = 0x06,
LED_PAR_CTRL_RX = 0x07,
LED_PAR_CTRL_ACT = 0x08,
LED_PAR_CTRL_LNK_RX = 0x09,
LED_PAR_CTRL_LNK_AC = 0x0a,
LED_PAR_CTRL_ACT_BL = 0x0b,
LED_PAR_CTRL_TX_BL = 0x0c,
LED_PAR_CTRL_RX_BL = 0x0d,
LED_PAR_CTRL_COL_BL = 0x0e,
LED_PAR_CTRL_INACT = 0x0f
};
/*****,PHY_MARV_FE_SPEC_2 16 bit r/w Specific Control Reg. 2 *****/
enum {
PHY_M_FESC_DIS_WAIT = 1<<2, /* Disable TDR Waiting Period */
PHY_M_FESC_ENA_MCLK = 1<<1, /* Enable MAC Rx Clock in sleep mode */
PHY_M_FESC_SEL_CL_A = 1<<0, /* Select Class A driver (100B-TX) */
};
/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
/***** PHY_MARV_PHY_CTRL (page 1) 16 bit r/w Fiber Specific Ctrl *****/
enum {
PHY_M_FIB_FORCE_LNK = 1<<10,/* Force Link Good */
PHY_M_FIB_SIGD_POL = 1<<9, /* SIGDET Polarity */
PHY_M_FIB_TX_DIS = 1<<3, /* Transmitter Disable */
};
/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
/***** PHY_MARV_PHY_CTRL (page 2) 16 bit r/w MAC Specific Ctrl *****/
enum {
PHY_M_MAC_MD_MSK = 7<<7, /* Bit 9.. 7: Mode Select Mask */
PHY_M_MAC_MD_AUTO = 3,/* Auto Copper/1000Base-X */
PHY_M_MAC_MD_COPPER = 5,/* Copper only */
PHY_M_MAC_MD_1000BX = 7,/* 1000Base-X only */
};
#define PHY_M_MAC_MODE_SEL(x) (((x)<<7) & PHY_M_MAC_MD_MSK)
/***** PHY_MARV_PHY_CTRL (page 3) 16 bit r/w LED Control Reg. *****/
enum {
PHY_M_LEDC_LOS_MSK = 0xf<<12,/* Bit 15..12: LOS LED Ctrl. Mask */
PHY_M_LEDC_INIT_MSK = 0xf<<8, /* Bit 11.. 8: INIT LED Ctrl. Mask */
PHY_M_LEDC_STA1_MSK = 0xf<<4,/* Bit 7.. 4: STAT1 LED Ctrl. Mask */
PHY_M_LEDC_STA0_MSK = 0xf, /* Bit 3.. 0: STAT0 LED Ctrl. Mask */
};
#define PHY_M_LEDC_LOS_CTRL(x) (((x)<<12) & PHY_M_LEDC_LOS_MSK)
#define PHY_M_LEDC_INIT_CTRL(x) (((x)<<8) & PHY_M_LEDC_INIT_MSK)
#define PHY_M_LEDC_STA1_CTRL(x) (((x)<<4) & PHY_M_LEDC_STA1_MSK)
#define PHY_M_LEDC_STA0_CTRL(x) (((x)<<0) & PHY_M_LEDC_STA0_MSK)
/* GMAC registers */
/* Port Registers */
enum {
GM_GP_STAT = 0x0000, /* 16 bit r/o General Purpose Status */
GM_GP_CTRL = 0x0004, /* 16 bit r/w General Purpose Control */
GM_TX_CTRL = 0x0008, /* 16 bit r/w Transmit Control Reg. */
GM_RX_CTRL = 0x000c, /* 16 bit r/w Receive Control Reg. */
GM_TX_FLOW_CTRL = 0x0010, /* 16 bit r/w Transmit Flow-Control */
GM_TX_PARAM = 0x0014, /* 16 bit r/w Transmit Parameter Reg. */
GM_SERIAL_MODE = 0x0018, /* 16 bit r/w Serial Mode Register */
/* Source Address Registers */
GM_SRC_ADDR_1L = 0x001c, /* 16 bit r/w Source Address 1 (low) */
GM_SRC_ADDR_1M = 0x0020, /* 16 bit r/w Source Address 1 (middle) */
GM_SRC_ADDR_1H = 0x0024, /* 16 bit r/w Source Address 1 (high) */
GM_SRC_ADDR_2L = 0x0028, /* 16 bit r/w Source Address 2 (low) */
GM_SRC_ADDR_2M = 0x002c, /* 16 bit r/w Source Address 2 (middle) */
GM_SRC_ADDR_2H = 0x0030, /* 16 bit r/w Source Address 2 (high) */
/* Multicast Address Hash Registers */
GM_MC_ADDR_H1 = 0x0034, /* 16 bit r/w Multicast Address Hash 1 */
GM_MC_ADDR_H2 = 0x0038, /* 16 bit r/w Multicast Address Hash 2 */
GM_MC_ADDR_H3 = 0x003c, /* 16 bit r/w Multicast Address Hash 3 */
GM_MC_ADDR_H4 = 0x0040, /* 16 bit r/w Multicast Address Hash 4 */
/* Interrupt Source Registers */
GM_TX_IRQ_SRC = 0x0044, /* 16 bit r/o Tx Overflow IRQ Source */
GM_RX_IRQ_SRC = 0x0048, /* 16 bit r/o Rx Overflow IRQ Source */
GM_TR_IRQ_SRC = 0x004c, /* 16 bit r/o Tx/Rx Over. IRQ Source */
/* Interrupt Mask Registers */
GM_TX_IRQ_MSK = 0x0050, /* 16 bit r/w Tx Overflow IRQ Mask */
GM_RX_IRQ_MSK = 0x0054, /* 16 bit r/w Rx Overflow IRQ Mask */
GM_TR_IRQ_MSK = 0x0058, /* 16 bit r/w Tx/Rx Over. IRQ Mask */
/* Serial Management Interface (SMI) Registers */
GM_SMI_CTRL = 0x0080, /* 16 bit r/w SMI Control Register */
GM_SMI_DATA = 0x0084, /* 16 bit r/w SMI Data Register */
GM_PHY_ADDR = 0x0088, /* 16 bit r/w GPHY Address Register */
/* MIB Counters */
GM_MIB_CNT_BASE = 0x0100, /* Base Address of MIB Counters */
GM_MIB_CNT_END = 0x025C, /* Last MIB counter */
};
/*
* MIB Counters base address definitions (low word) -
* use offset 4 for access to high word (32 bit r/o)
*/
enum {
GM_RXF_UC_OK = GM_MIB_CNT_BASE + 0, /* Unicast Frames Received OK */
GM_RXF_BC_OK = GM_MIB_CNT_BASE + 8, /* Broadcast Frames Received OK */
GM_RXF_MPAUSE = GM_MIB_CNT_BASE + 16, /* Pause MAC Ctrl Frames Received */
GM_RXF_MC_OK = GM_MIB_CNT_BASE + 24, /* Multicast Frames Received OK */
GM_RXF_FCS_ERR = GM_MIB_CNT_BASE + 32, /* Rx Frame Check Seq. Error */
GM_RXO_OK_LO = GM_MIB_CNT_BASE + 48, /* Octets Received OK Low */
GM_RXO_OK_HI = GM_MIB_CNT_BASE + 56, /* Octets Received OK High */
GM_RXO_ERR_LO = GM_MIB_CNT_BASE + 64, /* Octets Received Invalid Low */
GM_RXO_ERR_HI = GM_MIB_CNT_BASE + 72, /* Octets Received Invalid High */
GM_RXF_SHT = GM_MIB_CNT_BASE + 80, /* Frames <64 Byte Received OK */
GM_RXE_FRAG = GM_MIB_CNT_BASE + 88, /* Frames <64 Byte Received with FCS Err */
GM_RXF_64B = GM_MIB_CNT_BASE + 96, /* 64 Byte Rx Frame */
GM_RXF_127B = GM_MIB_CNT_BASE + 104,/* 65-127 Byte Rx Frame */
GM_RXF_255B = GM_MIB_CNT_BASE + 112,/* 128-255 Byte Rx Frame */
GM_RXF_511B = GM_MIB_CNT_BASE + 120,/* 256-511 Byte Rx Frame */
GM_RXF_1023B = GM_MIB_CNT_BASE + 128,/* 512-1023 Byte Rx Frame */
GM_RXF_1518B = GM_MIB_CNT_BASE + 136,/* 1024-1518 Byte Rx Frame */
GM_RXF_MAX_SZ = GM_MIB_CNT_BASE + 144,/* 1519-MaxSize Byte Rx Frame */
GM_RXF_LNG_ERR = GM_MIB_CNT_BASE + 152,/* Rx Frame too Long Error */
GM_RXF_JAB_PKT = GM_MIB_CNT_BASE + 160,/* Rx Jabber Packet Frame */
GM_RXE_FIFO_OV = GM_MIB_CNT_BASE + 176,/* Rx FIFO overflow Event */
GM_TXF_UC_OK = GM_MIB_CNT_BASE + 192,/* Unicast Frames Xmitted OK */
GM_TXF_BC_OK = GM_MIB_CNT_BASE + 200,/* Broadcast Frames Xmitted OK */
GM_TXF_MPAUSE = GM_MIB_CNT_BASE + 208,/* Pause MAC Ctrl Frames Xmitted */
GM_TXF_MC_OK = GM_MIB_CNT_BASE + 216,/* Multicast Frames Xmitted OK */
GM_TXO_OK_LO = GM_MIB_CNT_BASE + 224,/* Octets Transmitted OK Low */
GM_TXO_OK_HI = GM_MIB_CNT_BASE + 232,/* Octets Transmitted OK High */
GM_TXF_64B = GM_MIB_CNT_BASE + 240,/* 64 Byte Tx Frame */
GM_TXF_127B = GM_MIB_CNT_BASE + 248,/* 65-127 Byte Tx Frame */
GM_TXF_255B = GM_MIB_CNT_BASE + 256,/* 128-255 Byte Tx Frame */
GM_TXF_511B = GM_MIB_CNT_BASE + 264,/* 256-511 Byte Tx Frame */
GM_TXF_1023B = GM_MIB_CNT_BASE + 272,/* 512-1023 Byte Tx Frame */
GM_TXF_1518B = GM_MIB_CNT_BASE + 280,/* 1024-1518 Byte Tx Frame */
GM_TXF_MAX_SZ = GM_MIB_CNT_BASE + 288,/* 1519-MaxSize Byte Tx Frame */
GM_TXF_COL = GM_MIB_CNT_BASE + 304,/* Tx Collision */
GM_TXF_LAT_COL = GM_MIB_CNT_BASE + 312,/* Tx Late Collision */
GM_TXF_ABO_COL = GM_MIB_CNT_BASE + 320,/* Tx aborted due to Exces. Col. */
GM_TXF_MUL_COL = GM_MIB_CNT_BASE + 328,/* Tx Multiple Collision */
GM_TXF_SNG_COL = GM_MIB_CNT_BASE + 336,/* Tx Single Collision */
GM_TXE_FIFO_UR = GM_MIB_CNT_BASE + 344,/* Tx FIFO Underrun Event */
};
/* GMAC Bit Definitions */
/* GM_GP_STAT 16 bit r/o General Purpose Status Register */
enum {
GM_GPSR_SPEED = 1<<15, /* Bit 15: Port Speed (1 = 100 Mbps) */
GM_GPSR_DUPLEX = 1<<14, /* Bit 14: Duplex Mode (1 = Full) */
GM_GPSR_FC_TX_DIS = 1<<13, /* Bit 13: Tx Flow-Control Mode Disabled */
GM_GPSR_LINK_UP = 1<<12, /* Bit 12: Link Up Status */
GM_GPSR_PAUSE = 1<<11, /* Bit 11: Pause State */
GM_GPSR_TX_ACTIVE = 1<<10, /* Bit 10: Tx in Progress */
GM_GPSR_EXC_COL = 1<<9, /* Bit 9: Excessive Collisions Occured */
GM_GPSR_LAT_COL = 1<<8, /* Bit 8: Late Collisions Occured */
GM_GPSR_PHY_ST_CH = 1<<5, /* Bit 5: PHY Status Change */
GM_GPSR_GIG_SPEED = 1<<4, /* Bit 4: Gigabit Speed (1 = 1000 Mbps) */
GM_GPSR_PART_MODE = 1<<3, /* Bit 3: Partition mode */
GM_GPSR_FC_RX_DIS = 1<<2, /* Bit 2: Rx Flow-Control Mode Disabled */
GM_GPSR_PROM_EN = 1<<1, /* Bit 1: Promiscuous Mode Enabled */
};
/* GM_GP_CTRL 16 bit r/w General Purpose Control Register */
enum {
GM_GPCR_PROM_ENA = 1<<14, /* Bit 14: Enable Promiscuous Mode */
GM_GPCR_FC_TX_DIS = 1<<13, /* Bit 13: Disable Tx Flow-Control Mode */
GM_GPCR_TX_ENA = 1<<12, /* Bit 12: Enable Transmit */
GM_GPCR_RX_ENA = 1<<11, /* Bit 11: Enable Receive */
GM_GPCR_BURST_ENA = 1<<10, /* Bit 10: Enable Burst Mode */
GM_GPCR_LOOP_ENA = 1<<9, /* Bit 9: Enable MAC Loopback Mode */
GM_GPCR_PART_ENA = 1<<8, /* Bit 8: Enable Partition Mode */
GM_GPCR_GIGS_ENA = 1<<7, /* Bit 7: Gigabit Speed (1000 Mbps) */
GM_GPCR_FL_PASS = 1<<6, /* Bit 6: Force Link Pass */
GM_GPCR_DUP_FULL = 1<<5, /* Bit 5: Full Duplex Mode */
GM_GPCR_FC_RX_DIS = 1<<4, /* Bit 4: Disable Rx Flow-Control Mode */
GM_GPCR_SPEED_100 = 1<<3, /* Bit 3: Port Speed 100 Mbps */
GM_GPCR_AU_DUP_DIS = 1<<2, /* Bit 2: Disable Auto-Update Duplex */
GM_GPCR_AU_FCT_DIS = 1<<1, /* Bit 1: Disable Auto-Update Flow-C. */
GM_GPCR_AU_SPD_DIS = 1<<0, /* Bit 0: Disable Auto-Update Speed */
};
#define GM_GPCR_SPEED_1000 (GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100)
#define GM_GPCR_AU_ALL_DIS (GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS|GM_GPCR_AU_SPD_DIS)
/* GM_TX_CTRL 16 bit r/w Transmit Control Register */
enum {
GM_TXCR_FORCE_JAM = 1<<15, /* Bit 15: Force Jam / Flow-Control */
GM_TXCR_CRC_DIS = 1<<14, /* Bit 14: Disable insertion of CRC */
GM_TXCR_PAD_DIS = 1<<13, /* Bit 13: Disable padding of packets */
GM_TXCR_COL_THR_MSK = 7<<10, /* Bit 12..10: Collision Threshold */
};
#define TX_COL_THR(x) (((x)<<10) & GM_TXCR_COL_THR_MSK)
#define TX_COL_DEF 0x04
/* GM_RX_CTRL 16 bit r/w Receive Control Register */
enum {
GM_RXCR_UCF_ENA = 1<<15, /* Bit 15: Enable Unicast filtering */
GM_RXCR_MCF_ENA = 1<<14, /* Bit 14: Enable Multicast filtering */
GM_RXCR_CRC_DIS = 1<<13, /* Bit 13: Remove 4-byte CRC */
GM_RXCR_PASS_FC = 1<<12, /* Bit 12: Pass FC packets to FIFO */
};
/* GM_TX_PARAM 16 bit r/w Transmit Parameter Register */
enum {
GM_TXPA_JAMLEN_MSK = 0x03<<14, /* Bit 15..14: Jam Length */
GM_TXPA_JAMIPG_MSK = 0x1f<<9, /* Bit 13..9: Jam IPG */
GM_TXPA_JAMDAT_MSK = 0x1f<<4, /* Bit 8..4: IPG Jam to Data */
GM_TXPA_BO_LIM_MSK = 0x0f, /* Bit 3.. 0: Backoff Limit Mask */
TX_JAM_LEN_DEF = 0x03,
TX_JAM_IPG_DEF = 0x0b,
TX_IPG_JAM_DEF = 0x1c,
TX_BOF_LIM_DEF = 0x04,
};
#define TX_JAM_LEN_VAL(x) (((x)<<14) & GM_TXPA_JAMLEN_MSK)
#define TX_JAM_IPG_VAL(x) (((x)<<9) & GM_TXPA_JAMIPG_MSK)
#define TX_IPG_JAM_DATA(x) (((x)<<4) & GM_TXPA_JAMDAT_MSK)
#define TX_BACK_OFF_LIM(x) ((x) & GM_TXPA_BO_LIM_MSK)
/* GM_SERIAL_MODE 16 bit r/w Serial Mode Register */
enum {
GM_SMOD_DATABL_MSK = 0x1f<<11, /* Bit 15..11: Data Blinder (r/o) */
GM_SMOD_LIMIT_4 = 1<<10, /* Bit 10: 4 consecutive Tx trials */
GM_SMOD_VLAN_ENA = 1<<9, /* Bit 9: Enable VLAN (Max. Frame Len) */
GM_SMOD_JUMBO_ENA = 1<<8, /* Bit 8: Enable Jumbo (Max. Frame Len) */
GM_SMOD_IPG_MSK = 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */
};
#define DATA_BLIND_VAL(x) (((x)<<11) & GM_SMOD_DATABL_MSK)
#define DATA_BLIND_DEF 0x04
#define IPG_DATA_VAL(x) (x & GM_SMOD_IPG_MSK)
#define IPG_DATA_DEF 0x1e
/* GM_SMI_CTRL 16 bit r/w SMI Control Register */
enum {
GM_SMI_CT_PHY_A_MSK = 0x1f<<11,/* Bit 15..11: PHY Device Address */
GM_SMI_CT_REG_A_MSK = 0x1f<<6,/* Bit 10.. 6: PHY Register Address */
GM_SMI_CT_OP_RD = 1<<5, /* Bit 5: OpCode Read (0=Write)*/
GM_SMI_CT_RD_VAL = 1<<4, /* Bit 4: Read Valid (Read completed) */
GM_SMI_CT_BUSY = 1<<3, /* Bit 3: Busy (Operation in progress) */
};
#define GM_SMI_CT_PHY_AD(x) (((x)<<11) & GM_SMI_CT_PHY_A_MSK)
#define GM_SMI_CT_REG_AD(x) (((x)<<6) & GM_SMI_CT_REG_A_MSK)
/* GM_PHY_ADDR 16 bit r/w GPHY Address Register */
enum {
GM_PAR_MIB_CLR = 1<<5, /* Bit 5: Set MIB Clear Counter Mode */
GM_PAR_MIB_TST = 1<<4, /* Bit 4: MIB Load Counter (Test Mode) */
};
/* Receive Frame Status Encoding */
enum {
GMR_FS_LEN = 0xffff<<16, /* Bit 31..16: Rx Frame Length */
GMR_FS_VLAN = 1<<13, /* VLAN Packet */
GMR_FS_JABBER = 1<<12, /* Jabber Packet */
GMR_FS_UN_SIZE = 1<<11, /* Undersize Packet */
GMR_FS_MC = 1<<10, /* Multicast Packet */
GMR_FS_BC = 1<<9, /* Broadcast Packet */
GMR_FS_RX_OK = 1<<8, /* Receive OK (Good Packet) */
GMR_FS_GOOD_FC = 1<<7, /* Good Flow-Control Packet */
GMR_FS_BAD_FC = 1<<6, /* Bad Flow-Control Packet */
GMR_FS_MII_ERR = 1<<5, /* MII Error */
GMR_FS_LONG_ERR = 1<<4, /* Too Long Packet */
GMR_FS_FRAGMENT = 1<<3, /* Fragment */
GMR_FS_CRC_ERR = 1<<1, /* CRC Error */
GMR_FS_RX_FF_OV = 1<<0, /* Rx FIFO Overflow */
GMR_FS_ANY_ERR = GMR_FS_RX_FF_OV | GMR_FS_CRC_ERR |
GMR_FS_FRAGMENT | GMR_FS_LONG_ERR |
GMR_FS_MII_ERR | GMR_FS_BAD_FC |
GMR_FS_UN_SIZE | GMR_FS_JABBER,
};
/* RX_GMF_CTRL_T 32 bit Rx GMAC FIFO Control/Test */
enum {
RX_TRUNC_ON = 1<<27, /* enable packet truncation */
RX_TRUNC_OFF = 1<<26, /* disable packet truncation */
RX_VLAN_STRIP_ON = 1<<25, /* enable VLAN stripping */
RX_VLAN_STRIP_OFF = 1<<24, /* disable VLAN stripping */
GMF_WP_TST_ON = 1<<14, /* Write Pointer Test On */
GMF_WP_TST_OFF = 1<<13, /* Write Pointer Test Off */
GMF_WP_STEP = 1<<12, /* Write Pointer Step/Increment */
GMF_RP_TST_ON = 1<<10, /* Read Pointer Test On */
GMF_RP_TST_OFF = 1<<9, /* Read Pointer Test Off */
GMF_RP_STEP = 1<<8, /* Read Pointer Step/Increment */
GMF_RX_F_FL_ON = 1<<7, /* Rx FIFO Flush Mode On */
GMF_RX_F_FL_OFF = 1<<6, /* Rx FIFO Flush Mode Off */
GMF_CLI_RX_FO = 1<<5, /* Clear IRQ Rx FIFO Overrun */
GMF_CLI_RX_C = 1<<4, /* Clear IRQ Rx Frame Complete */
GMF_OPER_ON = 1<<3, /* Operational Mode On */
GMF_OPER_OFF = 1<<2, /* Operational Mode Off */
GMF_RST_CLR = 1<<1, /* Clear GMAC FIFO Reset */
GMF_RST_SET = 1<<0, /* Set GMAC FIFO Reset */
RX_GMF_FL_THR_DEF = 0xa, /* flush threshold (default) */
GMF_RX_CTRL_DEF = GMF_OPER_ON | GMF_RX_F_FL_ON,
};
/* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */
enum {
TX_STFW_DIS = 1<<31,/* Disable Store & Forward (Yukon-EC Ultra) */
TX_STFW_ENA = 1<<30,/* Enable Store & Forward (Yukon-EC Ultra) */
TX_VLAN_TAG_ON = 1<<25,/* enable VLAN tagging */
TX_VLAN_TAG_OFF = 1<<24,/* disable VLAN tagging */
GMF_WSP_TST_ON = 1<<18,/* Write Shadow Pointer Test On */
GMF_WSP_TST_OFF = 1<<17,/* Write Shadow Pointer Test Off */
GMF_WSP_STEP = 1<<16,/* Write Shadow Pointer Step/Increment */
GMF_CLI_TX_FU = 1<<6, /* Clear IRQ Tx FIFO Underrun */
GMF_CLI_TX_FC = 1<<5, /* Clear IRQ Tx Frame Complete */
GMF_CLI_TX_PE = 1<<4, /* Clear IRQ Tx Parity Error */
};
/* GMAC_TI_ST_CTRL 8 bit Time Stamp Timer Ctrl Reg (YUKON only) */
enum {
GMT_ST_START = 1<<2, /* Start Time Stamp Timer */
GMT_ST_STOP = 1<<1, /* Stop Time Stamp Timer */
GMT_ST_CLR_IRQ = 1<<0, /* Clear Time Stamp Timer IRQ */
};
/* B28_Y2_ASF_STAT_CMD 32 bit ASF Status and Command Reg */
enum {
Y2_ASF_OS_PRES = 1<<4, /* ASF operation system present */
Y2_ASF_RESET = 1<<3, /* ASF system in reset state */
Y2_ASF_RUNNING = 1<<2, /* ASF system operational */
Y2_ASF_CLR_HSTI = 1<<1, /* Clear ASF IRQ */
Y2_ASF_IRQ = 1<<0, /* Issue an IRQ to ASF system */
Y2_ASF_UC_STATE = 3<<2, /* ASF uC State */
Y2_ASF_CLK_HALT = 0, /* ASF system clock stopped */
};
/* B28_Y2_ASF_HOST_COM 32 bit ASF Host Communication Reg */
enum {
Y2_ASF_CLR_ASFI = 1<<1, /* Clear host IRQ */
Y2_ASF_HOST_IRQ = 1<<0, /* Issue an IRQ to HOST system */
};
/* STAT_CTRL 32 bit Status BMU control register (Yukon-2 only) */
enum {
SC_STAT_CLR_IRQ = 1<<4, /* Status Burst IRQ clear */
SC_STAT_OP_ON = 1<<3, /* Operational Mode On */
SC_STAT_OP_OFF = 1<<2, /* Operational Mode Off */
SC_STAT_RST_CLR = 1<<1, /* Clear Status Unit Reset (Enable) */
SC_STAT_RST_SET = 1<<0, /* Set Status Unit Reset */
};
/* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */
enum {
GMC_H_BURST_ON = 1<<7, /* Half Duplex Burst Mode On */
GMC_H_BURST_OFF = 1<<6, /* Half Duplex Burst Mode Off */
GMC_F_LOOPB_ON = 1<<5, /* FIFO Loopback On */
GMC_F_LOOPB_OFF = 1<<4, /* FIFO Loopback Off */
GMC_PAUSE_ON = 1<<3, /* Pause On */
GMC_PAUSE_OFF = 1<<2, /* Pause Off */
GMC_RST_CLR = 1<<1, /* Clear GMAC Reset */
GMC_RST_SET = 1<<0, /* Set GMAC Reset */
};
/* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */
enum {
GPC_SEL_BDT = 1<<28, /* Select Bi-Dir. Transfer for MDC/MDIO */
GPC_INT_POL_HI = 1<<27, /* IRQ Polarity is Active HIGH */
GPC_75_OHM = 1<<26, /* Use 75 Ohm Termination instead of 50 */
GPC_DIS_FC = 1<<25, /* Disable Automatic Fiber/Copper Detection */
GPC_DIS_SLEEP = 1<<24, /* Disable Energy Detect */
GPC_HWCFG_M_3 = 1<<23, /* HWCFG_MODE[3] */
GPC_HWCFG_M_2 = 1<<22, /* HWCFG_MODE[2] */
GPC_HWCFG_M_1 = 1<<21, /* HWCFG_MODE[1] */
GPC_HWCFG_M_0 = 1<<20, /* HWCFG_MODE[0] */
GPC_ANEG_0 = 1<<19, /* ANEG[0] */
GPC_ENA_XC = 1<<18, /* Enable MDI crossover */
GPC_DIS_125 = 1<<17, /* Disable 125 MHz clock */
GPC_ANEG_3 = 1<<16, /* ANEG[3] */
GPC_ANEG_2 = 1<<15, /* ANEG[2] */
GPC_ANEG_1 = 1<<14, /* ANEG[1] */
GPC_ENA_PAUSE = 1<<13, /* Enable Pause (SYM_OR_REM) */
GPC_PHYADDR_4 = 1<<12, /* Bit 4 of Phy Addr */
GPC_PHYADDR_3 = 1<<11, /* Bit 3 of Phy Addr */
GPC_PHYADDR_2 = 1<<10, /* Bit 2 of Phy Addr */
GPC_PHYADDR_1 = 1<<9, /* Bit 1 of Phy Addr */
GPC_PHYADDR_0 = 1<<8, /* Bit 0 of Phy Addr */
/* Bits 7..2: reserved */
GPC_RST_CLR = 1<<1, /* Clear GPHY Reset */
GPC_RST_SET = 1<<0, /* Set GPHY Reset */
};
/* GMAC_IRQ_SRC 8 bit GMAC Interrupt Source Reg (YUKON only) */
/* GMAC_IRQ_MSK 8 bit GMAC Interrupt Mask Reg (YUKON only) */
enum {
GM_IS_TX_CO_OV = 1<<5, /* Transmit Counter Overflow IRQ */
GM_IS_RX_CO_OV = 1<<4, /* Receive Counter Overflow IRQ */
GM_IS_TX_FF_UR = 1<<3, /* Transmit FIFO Underrun */
GM_IS_TX_COMPL = 1<<2, /* Frame Transmission Complete */
GM_IS_RX_FF_OR = 1<<1, /* Receive FIFO Overrun */
GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */
#define GMAC_DEF_MSK GM_IS_TX_FF_UR
/* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */
/* Bits 15.. 2: reserved */
GMLC_RST_CLR = 1<<1, /* Clear GMAC Link Reset */
GMLC_RST_SET = 1<<0, /* Set GMAC Link Reset */
/* WOL_CTRL_STAT 16 bit WOL Control/Status Reg */
WOL_CTL_LINK_CHG_OCC = 1<<15,
WOL_CTL_MAGIC_PKT_OCC = 1<<14,
WOL_CTL_PATTERN_OCC = 1<<13,
WOL_CTL_CLEAR_RESULT = 1<<12,
WOL_CTL_ENA_PME_ON_LINK_CHG = 1<<11,
WOL_CTL_DIS_PME_ON_LINK_CHG = 1<<10,
WOL_CTL_ENA_PME_ON_MAGIC_PKT = 1<<9,
WOL_CTL_DIS_PME_ON_MAGIC_PKT = 1<<8,
WOL_CTL_ENA_PME_ON_PATTERN = 1<<7,
WOL_CTL_DIS_PME_ON_PATTERN = 1<<6,
WOL_CTL_ENA_LINK_CHG_UNIT = 1<<5,
WOL_CTL_DIS_LINK_CHG_UNIT = 1<<4,
WOL_CTL_ENA_MAGIC_PKT_UNIT = 1<<3,
WOL_CTL_DIS_MAGIC_PKT_UNIT = 1<<2,
WOL_CTL_ENA_PATTERN_UNIT = 1<<1,
WOL_CTL_DIS_PATTERN_UNIT = 1<<0,
};
#define WOL_CTL_DEFAULT \
(WOL_CTL_DIS_PME_ON_LINK_CHG | \
WOL_CTL_DIS_PME_ON_PATTERN | \
WOL_CTL_DIS_PME_ON_MAGIC_PKT | \
WOL_CTL_DIS_LINK_CHG_UNIT | \
WOL_CTL_DIS_PATTERN_UNIT | \
WOL_CTL_DIS_MAGIC_PKT_UNIT)
/* WOL_MATCH_CTL 8 bit WOL Match Control Reg */
#define WOL_CTL_PATT_ENA(x) (1 << (x))
/* Control flags */
enum {
UDPTCP = 1<<0,
CALSUM = 1<<1,
WR_SUM = 1<<2,
INIT_SUM= 1<<3,
LOCK_SUM= 1<<4,
INS_VLAN= 1<<5,
EOP = 1<<7,
};
enum {
HW_OWNER = 1<<7,
OP_TCPWRITE = 0x11,
OP_TCPSTART = 0x12,
OP_TCPINIT = 0x14,
OP_TCPLCK = 0x18,
OP_TCPCHKSUM = OP_TCPSTART,
OP_TCPIS = OP_TCPINIT | OP_TCPSTART,
OP_TCPLW = OP_TCPLCK | OP_TCPWRITE,
OP_TCPLSW = OP_TCPLCK | OP_TCPSTART | OP_TCPWRITE,
OP_TCPLISW = OP_TCPLCK | OP_TCPINIT | OP_TCPSTART | OP_TCPWRITE,
OP_ADDR64 = 0x21,
OP_VLAN = 0x22,
OP_ADDR64VLAN = OP_ADDR64 | OP_VLAN,
OP_LRGLEN = 0x24,
OP_LRGLENVLAN = OP_LRGLEN | OP_VLAN,
OP_BUFFER = 0x40,
OP_PACKET = 0x41,
OP_LARGESEND = 0x43,
/* YUKON-2 STATUS opcodes defines */
OP_RXSTAT = 0x60,
OP_RXTIMESTAMP = 0x61,
OP_RXVLAN = 0x62,
OP_RXCHKS = 0x64,
OP_RXCHKSVLAN = OP_RXCHKS | OP_RXVLAN,
OP_RXTIMEVLAN = OP_RXTIMESTAMP | OP_RXVLAN,
OP_RSS_HASH = 0x65,
OP_TXINDEXLE = 0x68,
};
/* Yukon 2 hardware interface */
struct sky2_tx_le {
__le32 addr;
__le16 length; /* also vlan tag or checksum start */
u8 ctrl;
u8 opcode;
} __attribute((packed));
struct sky2_rx_le {
__le32 addr;
__le16 length;
u8 ctrl;
u8 opcode;
} __attribute((packed));
struct sky2_status_le {
__le32 status; /* also checksum */
__le16 length; /* also vlan tag */
u8 link;
u8 opcode;
} __attribute((packed));
struct tx_ring_info {
struct sk_buff *skb;
DECLARE_PCI_UNMAP_ADDR(mapaddr);
DECLARE_PCI_UNMAP_ADDR(maplen);
};
struct rx_ring_info {
struct sk_buff *skb;
dma_addr_t data_addr;
DECLARE_PCI_UNMAP_ADDR(data_size);
dma_addr_t frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
};
struct sky2_port {
struct sky2_hw *hw;
struct net_device *netdev;
unsigned port;
u32 msg_enable;
spinlock_t phy_lock;
struct tx_ring_info *tx_ring;
struct sky2_tx_le *tx_le;
u16 tx_cons; /* next le to check */
u16 tx_prod; /* next le to use */
u32 tx_addr64;
u16 tx_pending;
u16 tx_last_mss;
u32 tx_tcpsum;
struct rx_ring_info *rx_ring ____cacheline_aligned_in_smp;
struct sky2_rx_le *rx_le;
u32 rx_addr64;
u16 rx_next; /* next re to check */
u16 rx_put; /* next le index to use */
u16 rx_pending;
u16 rx_data_size;
u16 rx_nfrags;
#ifdef SKY2_VLAN_TAG_USED
u16 rx_tag;
struct vlan_group *vlgrp;
#endif
dma_addr_t rx_le_map;
dma_addr_t tx_le_map;
u32 advertising; /* ADVERTISED_ bits */
u16 speed; /* SPEED_1000, SPEED_100, ... */
u8 autoneg; /* AUTONEG_ENABLE, AUTONEG_DISABLE */
u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */
u8 rx_pause;
u8 tx_pause;
u8 rx_csum;
struct net_device_stats net_stats;
};
struct sky2_hw {
void __iomem *regs;
struct pci_dev *pdev;
struct net_device *dev[2];
int pm_cap;
int err_cap;
u8 chip_id;
u8 chip_rev;
u8 pmd_type;
u8 ports;
struct sky2_status_le *st_le;
u32 st_idx;
dma_addr_t st_dma;
struct timer_list idle_timer;
int msi_detected;
wait_queue_head_t msi_wait;
};
static inline int sky2_is_copper(const struct sky2_hw *hw)
{
return !(hw->pmd_type == 'L' || hw->pmd_type == 'S' || hw->pmd_type == 'P');
}
/* Register accessor for memory mapped device */
static inline u32 sky2_read32(const struct sky2_hw *hw, unsigned reg)
{
return readl(hw->regs + reg);
}
static inline u16 sky2_read16(const struct sky2_hw *hw, unsigned reg)
{
return readw(hw->regs + reg);
}
static inline u8 sky2_read8(const struct sky2_hw *hw, unsigned reg)
{
return readb(hw->regs + reg);
}
static inline void sky2_write32(const struct sky2_hw *hw, unsigned reg, u32 val)
{
writel(val, hw->regs + reg);
}
static inline void sky2_write16(const struct sky2_hw *hw, unsigned reg, u16 val)
{
writew(val, hw->regs + reg);
}
static inline void sky2_write8(const struct sky2_hw *hw, unsigned reg, u8 val)
{
writeb(val, hw->regs + reg);
}
/* Yukon PHY related registers */
#define SK_GMAC_REG(port,reg) \
(BASE_GMAC_1 + (port) * (BASE_GMAC_2-BASE_GMAC_1) + (reg))
#define GM_PHY_RETRIES 100
static inline u16 gma_read16(const struct sky2_hw *hw, unsigned port, unsigned reg)
{
return sky2_read16(hw, SK_GMAC_REG(port,reg));
}
static inline u32 gma_read32(struct sky2_hw *hw, unsigned port, unsigned reg)
{
unsigned base = SK_GMAC_REG(port, reg);
return (u32) sky2_read16(hw, base)
| (u32) sky2_read16(hw, base+4) << 16;
}
static inline void gma_write16(const struct sky2_hw *hw, unsigned port, int r, u16 v)
{
sky2_write16(hw, SK_GMAC_REG(port,r), v);
}
static inline void gma_set_addr(struct sky2_hw *hw, unsigned port, unsigned reg,
const u8 *addr)
{
gma_write16(hw, port, reg, (u16) addr[0] | ((u16) addr[1] << 8));
gma_write16(hw, port, reg+4,(u16) addr[2] | ((u16) addr[3] << 8));
gma_write16(hw, port, reg+8,(u16) addr[4] | ((u16) addr[5] << 8));
}
/* PCI config space access */
static inline u32 sky2_pci_read32(const struct sky2_hw *hw, unsigned reg)
{
return sky2_read32(hw, Y2_CFG_SPC + reg);
}
static inline u16 sky2_pci_read16(const struct sky2_hw *hw, unsigned reg)
{
return sky2_read16(hw, Y2_CFG_SPC + reg);
}
static inline void sky2_pci_write32(struct sky2_hw *hw, unsigned reg, u32 val)
{
sky2_write32(hw, Y2_CFG_SPC + reg, val);
}
static inline void sky2_pci_write16(struct sky2_hw *hw, unsigned reg, u16 val)
{
sky2_write16(hw, Y2_CFG_SPC + reg, val);
}
#endif