linux/drivers/pcmcia/sa1100_generic.c
Richard Purdie f36598aeca [ARM] 2873/1: PCMCIA soc: Allow access to filesystems on CF at boot time
Patch from Richard Purdie

This change makes the soc pcmcia interfaces available earlier in the
boot process meaning devices like CF microdrives can be used for the
root filesystem.

Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-09-03 19:39:25 +01:00

131 lines
3.8 KiB
C

/*======================================================================
Device driver for the PCMCIA control functionality of StrongARM
SA-1100 microprocessors.
The contents of this file are subject to the Mozilla Public
License Version 1.1 (the "License"); you may not use this file
except in compliance with the License. You may obtain a copy of
the License at http://www.mozilla.org/MPL/
Software distributed under the License is distributed on an "AS
IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
implied. See the License for the specific language governing
rights and limitations under the License.
The initial developer of the original code is John G. Dorsey
<john+@cs.cmu.edu>. Portions created by John G. Dorsey are
Copyright (C) 1999 John G. Dorsey. All Rights Reserved.
Alternatively, the contents of this file may be used under the
terms of the GNU Public License version 2 (the "GPL"), in which
case the provisions of the GPL are applicable instead of the
above. If you wish to allow the use of your version of this file
only under the terms of the GPL and not to allow others to use
your version of this file under the MPL, indicate your decision
by deleting the provisions above and replace them with the notice
and other provisions required by the GPL. If you do not delete
the provisions above, a recipient may use your version of this
file under either the MPL or the GPL.
======================================================================*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/config.h>
#include <pcmcia/cs_types.h>
#include <pcmcia/cs.h>
#include <pcmcia/ss.h>
#include "sa1100_generic.h"
static int (*sa11x0_pcmcia_hw_init[])(struct device *dev) = {
#ifdef CONFIG_SA1100_ASSABET
pcmcia_assabet_init,
#endif
#ifdef CONFIG_SA1100_CERF
pcmcia_cerf_init,
#endif
#ifdef CONFIG_SA1100_H3600
pcmcia_h3600_init,
#endif
#ifdef CONFIG_SA1100_SHANNON
pcmcia_shannon_init,
#endif
#ifdef CONFIG_SA1100_SIMPAD
pcmcia_simpad_init,
#endif
};
static int sa11x0_drv_pcmcia_probe(struct device *dev)
{
int i, ret = -ENODEV;
/*
* Initialise any "on-board" PCMCIA sockets.
*/
for (i = 0; i < ARRAY_SIZE(sa11x0_pcmcia_hw_init); i++) {
ret = sa11x0_pcmcia_hw_init[i](dev);
if (ret == 0)
break;
}
return ret;
}
static int sa11x0_drv_pcmcia_suspend(struct device *dev, pm_message_t state, u32 level)
{
int ret = 0;
if (level == SUSPEND_SAVE_STATE)
ret = pcmcia_socket_dev_suspend(dev, state);
return ret;
}
static int sa11x0_drv_pcmcia_resume(struct device *dev, u32 level)
{
int ret = 0;
if (level == RESUME_RESTORE_STATE)
ret = pcmcia_socket_dev_resume(dev);
return ret;
}
static struct device_driver sa11x0_pcmcia_driver = {
.probe = sa11x0_drv_pcmcia_probe,
.remove = soc_common_drv_pcmcia_remove,
.name = "sa11x0-pcmcia",
.bus = &platform_bus_type,
.suspend = sa11x0_drv_pcmcia_suspend,
.resume = sa11x0_drv_pcmcia_resume,
};
/* sa11x0_pcmcia_init()
* ^^^^^^^^^^^^^^^^^^^^
*
* This routine performs low-level PCMCIA initialization and then
* registers this socket driver with Card Services.
*
* Returns: 0 on success, -ve error code on failure
*/
static int __init sa11x0_pcmcia_init(void)
{
return driver_register(&sa11x0_pcmcia_driver);
}
/* sa11x0_pcmcia_exit()
* ^^^^^^^^^^^^^^^^^^^^
* Invokes the low-level kernel service to free IRQs associated with this
* socket controller and reset GPIO edge detection.
*/
static void __exit sa11x0_pcmcia_exit(void)
{
driver_unregister(&sa11x0_pcmcia_driver);
}
MODULE_AUTHOR("John Dorsey <john+@cs.cmu.edu>");
MODULE_DESCRIPTION("Linux PCMCIA Card Services: SA-11x0 Socket Controller");
MODULE_LICENSE("Dual MPL/GPL");
fs_initcall(sa11x0_pcmcia_init);
module_exit(sa11x0_pcmcia_exit);