linux/drivers/hwmon/k8temp.c
Andreas Herrmann d535bad90d hwmon: (k8temp) Fix temperature reporting for ASB1 processor revisions
Reported temperature for ASB1 CPUs is too high.
Add ASB1 CPU revisions (these are also non-desktop variants) to the
list of CPUs for which the temperature fixup is not required.

Example: (from LENOVO ThinkPad Edge 13, 01972NG, system was idle)

  Current kernel reports

  $ sensors
  k8temp-pci-00c3
  Adapter: PCI adapter
  Core0 Temp:  +74.0 C
  Core0 Temp:  +70.0 C
  Core1 Temp:  +69.0 C
  Core1 Temp:  +70.0 C

  With this patch I have

  $ sensors
  k8temp-pci-00c3
  Adapter: PCI adapter
  Core0 Temp:  +54.0 C
  Core0 Temp:  +51.0 C
  Core1 Temp:  +48.0 C
  Core1 Temp:  +49.0 C

Cc: stable@kernel.org [.32.x .33.x, .34.x]
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-07-09 16:22:47 +02:00

334 lines
8.9 KiB
C

/*
* k8temp.c - Linux kernel module for hardware monitoring
*
* Copyright (C) 2006 Rudolf Marek <r.marek@assembler.cz>
*
* Inspired from the w83785 and amd756 drivers.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
* 02110-1301 USA.
*/
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/pci.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/mutex.h>
#include <asm/processor.h>
#define TEMP_FROM_REG(val) (((((val) >> 16) & 0xff) - 49) * 1000)
#define REG_TEMP 0xe4
#define SEL_PLACE 0x40
#define SEL_CORE 0x04
struct k8temp_data {
struct device *hwmon_dev;
struct mutex update_lock;
const char *name;
char valid; /* zero until following fields are valid */
unsigned long last_updated; /* in jiffies */
/* registers values */
u8 sensorsp; /* sensor presence bits - SEL_CORE & SEL_PLACE */
u32 temp[2][2]; /* core, place */
u8 swap_core_select; /* meaning of SEL_CORE is inverted */
u32 temp_offset;
};
static struct k8temp_data *k8temp_update_device(struct device *dev)
{
struct k8temp_data *data = dev_get_drvdata(dev);
struct pci_dev *pdev = to_pci_dev(dev);
u8 tmp;
mutex_lock(&data->update_lock);
if (!data->valid
|| time_after(jiffies, data->last_updated + HZ)) {
pci_read_config_byte(pdev, REG_TEMP, &tmp);
tmp &= ~(SEL_PLACE | SEL_CORE); /* Select sensor 0, core0 */
pci_write_config_byte(pdev, REG_TEMP, tmp);
pci_read_config_dword(pdev, REG_TEMP, &data->temp[0][0]);
if (data->sensorsp & SEL_PLACE) {
tmp |= SEL_PLACE; /* Select sensor 1, core0 */
pci_write_config_byte(pdev, REG_TEMP, tmp);
pci_read_config_dword(pdev, REG_TEMP,
&data->temp[0][1]);
}
if (data->sensorsp & SEL_CORE) {
tmp &= ~SEL_PLACE; /* Select sensor 0, core1 */
tmp |= SEL_CORE;
pci_write_config_byte(pdev, REG_TEMP, tmp);
pci_read_config_dword(pdev, REG_TEMP,
&data->temp[1][0]);
if (data->sensorsp & SEL_PLACE) {
tmp |= SEL_PLACE; /* Select sensor 1, core1 */
pci_write_config_byte(pdev, REG_TEMP, tmp);
pci_read_config_dword(pdev, REG_TEMP,
&data->temp[1][1]);
}
}
data->last_updated = jiffies;
data->valid = 1;
}
mutex_unlock(&data->update_lock);
return data;
}
/*
* Sysfs stuff
*/
static ssize_t show_name(struct device *dev, struct device_attribute
*devattr, char *buf)
{
struct k8temp_data *data = dev_get_drvdata(dev);
return sprintf(buf, "%s\n", data->name);
}
static ssize_t show_temp(struct device *dev,
struct device_attribute *devattr, char *buf)
{
struct sensor_device_attribute_2 *attr =
to_sensor_dev_attr_2(devattr);
int core = attr->nr;
int place = attr->index;
int temp;
struct k8temp_data *data = k8temp_update_device(dev);
if (data->swap_core_select && (data->sensorsp & SEL_CORE))
core = core ? 0 : 1;
temp = TEMP_FROM_REG(data->temp[core][place]) + data->temp_offset;
return sprintf(buf, "%d\n", temp);
}
/* core, place */
static SENSOR_DEVICE_ATTR_2(temp1_input, S_IRUGO, show_temp, NULL, 0, 0);
static SENSOR_DEVICE_ATTR_2(temp2_input, S_IRUGO, show_temp, NULL, 0, 1);
static SENSOR_DEVICE_ATTR_2(temp3_input, S_IRUGO, show_temp, NULL, 1, 0);
static SENSOR_DEVICE_ATTR_2(temp4_input, S_IRUGO, show_temp, NULL, 1, 1);
static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
static const struct pci_device_id k8temp_ids[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_K8_NB_MISC) },
{ 0 },
};
MODULE_DEVICE_TABLE(pci, k8temp_ids);
static int __devinit k8temp_probe(struct pci_dev *pdev,
const struct pci_device_id *id)
{
int err;
u8 scfg;
u32 temp;
u8 model, stepping;
struct k8temp_data *data;
if (!(data = kzalloc(sizeof(struct k8temp_data), GFP_KERNEL))) {
err = -ENOMEM;
goto exit;
}
model = boot_cpu_data.x86_model;
stepping = boot_cpu_data.x86_mask;
switch (boot_cpu_data.x86) {
case 0xf:
/* feature available since SH-C0, exclude older revisions */
if (((model == 4) && (stepping == 0)) ||
((model == 5) && (stepping <= 1))) {
err = -ENODEV;
goto exit_free;
}
/*
* AMD NPT family 0fh, i.e. RevF and RevG:
* meaning of SEL_CORE bit is inverted
*/
if (model >= 0x40) {
data->swap_core_select = 1;
dev_warn(&pdev->dev, "Temperature readouts might be "
"wrong - check erratum #141\n");
}
if ((model >= 0x69) &&
!(model == 0xc1 || model == 0x6c || model == 0x7c ||
model == 0x6b || model == 0x6f || model == 0x7f)) {
/*
* RevG desktop CPUs (i.e. no socket S1G1 or
* ASB1 parts) need additional offset,
* otherwise reported temperature is below
* ambient temperature
*/
data->temp_offset = 21000;
}
break;
}
pci_read_config_byte(pdev, REG_TEMP, &scfg);
scfg &= ~(SEL_PLACE | SEL_CORE); /* Select sensor 0, core0 */
pci_write_config_byte(pdev, REG_TEMP, scfg);
pci_read_config_byte(pdev, REG_TEMP, &scfg);
if (scfg & (SEL_PLACE | SEL_CORE)) {
dev_err(&pdev->dev, "Configuration bit(s) stuck at 1!\n");
err = -ENODEV;
goto exit_free;
}
scfg |= (SEL_PLACE | SEL_CORE);
pci_write_config_byte(pdev, REG_TEMP, scfg);
/* now we know if we can change core and/or sensor */
pci_read_config_byte(pdev, REG_TEMP, &data->sensorsp);
if (data->sensorsp & SEL_PLACE) {
scfg &= ~SEL_CORE; /* Select sensor 1, core0 */
pci_write_config_byte(pdev, REG_TEMP, scfg);
pci_read_config_dword(pdev, REG_TEMP, &temp);
scfg |= SEL_CORE; /* prepare for next selection */
if (!((temp >> 16) & 0xff)) /* if temp is 0 -49C is not likely */
data->sensorsp &= ~SEL_PLACE;
}
if (data->sensorsp & SEL_CORE) {
scfg &= ~SEL_PLACE; /* Select sensor 0, core1 */
pci_write_config_byte(pdev, REG_TEMP, scfg);
pci_read_config_dword(pdev, REG_TEMP, &temp);
if (!((temp >> 16) & 0xff)) /* if temp is 0 -49C is not likely */
data->sensorsp &= ~SEL_CORE;
}
data->name = "k8temp";
mutex_init(&data->update_lock);
dev_set_drvdata(&pdev->dev, data);
/* Register sysfs hooks */
err = device_create_file(&pdev->dev,
&sensor_dev_attr_temp1_input.dev_attr);
if (err)
goto exit_remove;
/* sensor can be changed and reports something */
if (data->sensorsp & SEL_PLACE) {
err = device_create_file(&pdev->dev,
&sensor_dev_attr_temp2_input.dev_attr);
if (err)
goto exit_remove;
}
/* core can be changed and reports something */
if (data->sensorsp & SEL_CORE) {
err = device_create_file(&pdev->dev,
&sensor_dev_attr_temp3_input.dev_attr);
if (err)
goto exit_remove;
if (data->sensorsp & SEL_PLACE)
err = device_create_file(&pdev->dev,
&sensor_dev_attr_temp4_input.
dev_attr);
if (err)
goto exit_remove;
}
err = device_create_file(&pdev->dev, &dev_attr_name);
if (err)
goto exit_remove;
data->hwmon_dev = hwmon_device_register(&pdev->dev);
if (IS_ERR(data->hwmon_dev)) {
err = PTR_ERR(data->hwmon_dev);
goto exit_remove;
}
return 0;
exit_remove:
device_remove_file(&pdev->dev,
&sensor_dev_attr_temp1_input.dev_attr);
device_remove_file(&pdev->dev,
&sensor_dev_attr_temp2_input.dev_attr);
device_remove_file(&pdev->dev,
&sensor_dev_attr_temp3_input.dev_attr);
device_remove_file(&pdev->dev,
&sensor_dev_attr_temp4_input.dev_attr);
device_remove_file(&pdev->dev, &dev_attr_name);
exit_free:
dev_set_drvdata(&pdev->dev, NULL);
kfree(data);
exit:
return err;
}
static void __devexit k8temp_remove(struct pci_dev *pdev)
{
struct k8temp_data *data = dev_get_drvdata(&pdev->dev);
hwmon_device_unregister(data->hwmon_dev);
device_remove_file(&pdev->dev,
&sensor_dev_attr_temp1_input.dev_attr);
device_remove_file(&pdev->dev,
&sensor_dev_attr_temp2_input.dev_attr);
device_remove_file(&pdev->dev,
&sensor_dev_attr_temp3_input.dev_attr);
device_remove_file(&pdev->dev,
&sensor_dev_attr_temp4_input.dev_attr);
device_remove_file(&pdev->dev, &dev_attr_name);
dev_set_drvdata(&pdev->dev, NULL);
kfree(data);
}
static struct pci_driver k8temp_driver = {
.name = "k8temp",
.id_table = k8temp_ids,
.probe = k8temp_probe,
.remove = __devexit_p(k8temp_remove),
};
static int __init k8temp_init(void)
{
return pci_register_driver(&k8temp_driver);
}
static void __exit k8temp_exit(void)
{
pci_unregister_driver(&k8temp_driver);
}
MODULE_AUTHOR("Rudolf Marek <r.marek@assembler.cz>");
MODULE_DESCRIPTION("AMD K8 core temperature monitor");
MODULE_LICENSE("GPL");
module_init(k8temp_init)
module_exit(k8temp_exit)