linux

History

Colin Ian King caa97be1a2 char/mwave: make some arrays static const to make object code smaller Don't populate arrays on the stack but make them static. Makes the object code smaller. Also remove temporary variables that have hard coded array sizes and just use ARRAY_SIZE instead and wrap some lines that are wider than 80 chars to clean up some checkpatch warnings. Before: text data bss dec hex filename 11141 2008 64 13213 339d drivers/char/mwave/smapi.o After: text data bss dec hex filename 10697 2352 64 13113 3339 drivers/char/mwave/smapi.o Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>		2017-07-17 17:23:16 +02:00
..
3780i.c	Replace <asm/uaccess.h> with <linux/uaccess.h> globally	2016-12-24 11:46:01 -08:00
3780i.h	char/mwave: remove custom BOOLEAN type	2016-08-31 14:22:49 +02:00
Makefile	char: change to new flag variable	2011-03-17 14:02:59 +01:00
mwavedd.c	Annotate hardware config module parameters in drivers/char/mwave/	2017-04-20 12:02:32 +01:00
mwavedd.h	Replace <asm/uaccess.h> with <linux/uaccess.h> globally	2016-12-24 11:46:01 -08:00
mwavepub.h
README	char: change to new flag variable	2011-03-17 14:02:59 +01:00
smapi.c	char/mwave: make some arrays static const to make object code smaller	2017-07-17 17:23:16 +02:00
smapi.h	char/mwave: remove custom BOOLEAN type	2016-08-31 14:22:49 +02:00
tp3780i.c	char/mwave: remove custom BOOLEAN type	2016-08-31 14:22:49 +02:00
tp3780i.h

README

Module options
--------------

The mwave module takes the following options.  Note that these options
are not saved by the BIOS and so do not persist after unload and reload.

  mwave_debug=value, where value is bitwise OR of trace flags:
	0x0001 mwavedd api tracing
	0x0002 smapi api tracing
	0x0004 3780i tracing
	0x0008 tp3780i tracing

        Tracing only occurs if the driver has been compiled with the
        MW_TRACE macro #defined  (i.e. let ccflags-y := -DMW_TRACE
        in the Makefile).

  mwave_3780i_irq=5/7/10/11/15
	If the dsp irq has not been setup and stored in bios by the 
	thinkpad configuration utility then this parameter allows the
	irq used by the dsp to be configured.

  mwave_3780i_io=0x130/0x350/0x0070/0xDB0
	If the dsp io range has not been setup and stored in bios by the 
	thinkpad configuration utility then this parameter allows the
	io range used by the dsp to be configured.

  mwave_uart_irq=3/4
	If the mwave's uart irq has not been setup and stored in bios by the 
	thinkpad configuration utility then this parameter allows the
	irq used by the mwave uart to be configured.

  mwave_uart_io=0x3f8/0x2f8/0x3E8/0x2E8
	If the uart io range has not been setup and stored in bios by the 
	thinkpad configuration utility then this parameter allows the
	io range used by the mwave uart to be configured.

Example to enable the 3780i DSP using ttyS1 resources:
	
  insmod mwave mwave_3780i_irq=10 mwave_3780i_io=0x0130 mwave_uart_irq=3 mwave_uart_io=0x2f8

Accessing the driver
--------------------

You must also create a node for the driver:
  mkdir -p /dev/modems
  mknod --mode=660 /dev/modems/mwave c 10 219