linux/drivers/spi/Makefile
Erik Gilling 0c03a1dd5b spi: add spi_tegra driver
v2 changes:
  from Thierry Reding:
    * add "select TEGRA_SYSTEM_DMA" to Kconfig
  from Grant Likely:
    * add oneline description to header
    * inline references to DRIVER_NAME
    * inline references to BUSY_TIMEOUT
    * open coded bytes_per_word()
    * spi_readl/writel -> spi_tegra_readl/writel
    * move transfer validation to spi_tegra_transfer
    * don't request_mem_region iomem as platform bus does that for us
    * __exit -> __devexit

v3 changes:
  from Russell King:
    * put request_mem_region back int
  from Grant Likely:
    * remove #undef DEBUG
    * add SLINK_ to register bit defines
    * remove unused bytes_per_word
    * make spi_tegra_readl/writel static linine
    * various refactoring for clarity
    * mark err if BSY bit is not cleared after 1000 retries
    * move spinlock to protect setting of RDY bit
    * subsys_initcall -> module_init

v3 changes:
  from Grant Likely:
    * update spi_tegra to use PTR_ERRless dma API

v4 changes:
  from Grant Likely:
    * remove empty spi_tegra_cleanup fucntion
    * allow device ids of -1

Signed-off-by: Erik Gilling <konkers@android.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Russell King <linux@arm.linux.org.uk>

spi: tegra: cleanups from upstream review

Change-Id: Icecf7e64efcb39de072a15234ba1faa4bad40d25
Signed-off-by: Erik Gilling <konkers@android.com>
2010-10-21 18:15:05 -07:00

69 lines
2.5 KiB
Makefile

#
# Makefile for kernel SPI drivers.
#
ccflags-$(CONFIG_SPI_DEBUG) := -DDEBUG
# small core, mostly translating board-specific
# config declarations into driver model code
obj-$(CONFIG_SPI_MASTER) += spi.o
# SPI master controller drivers (bus)
obj-$(CONFIG_SPI_ATMEL) += atmel_spi.o
obj-$(CONFIG_SPI_BFIN) += spi_bfin5xx.o
obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o
obj-$(CONFIG_SPI_AU1550) += au1550_spi.o
obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o
obj-$(CONFIG_SPI_COLDFIRE_QSPI) += coldfire_qspi.o
obj-$(CONFIG_SPI_DAVINCI) += davinci_spi.o
obj-$(CONFIG_SPI_DESIGNWARE) += dw_spi.o
obj-$(CONFIG_SPI_DW_PCI) += dw_spi_pci.o
obj-$(CONFIG_SPI_DW_MMIO) += dw_spi_mmio.o
obj-$(CONFIG_SPI_EP93XX) += ep93xx_spi.o
obj-$(CONFIG_SPI_GPIO) += spi_gpio.o
obj-$(CONFIG_SPI_IMX) += spi_imx.o
obj-$(CONFIG_SPI_LM70_LLP) += spi_lm70llp.o
obj-$(CONFIG_SPI_PXA2XX) += pxa2xx_spi.o
obj-$(CONFIG_SPI_OMAP_UWIRE) += omap_uwire.o
obj-$(CONFIG_SPI_OMAP24XX) += omap2_mcspi.o
obj-$(CONFIG_SPI_OMAP_100K) += omap_spi_100k.o
obj-$(CONFIG_SPI_ORION) += orion_spi.o
obj-$(CONFIG_SPI_PL022) += amba-pl022.o
obj-$(CONFIG_SPI_MPC512x_PSC) += mpc512x_psc_spi.o
obj-$(CONFIG_SPI_MPC52xx_PSC) += mpc52xx_psc_spi.o
obj-$(CONFIG_SPI_MPC52xx) += mpc52xx_spi.o
obj-$(CONFIG_SPI_FSL_LIB) += spi_fsl_lib.o
obj-$(CONFIG_SPI_FSL_ESPI) += spi_fsl_espi.o
obj-$(CONFIG_SPI_FSL_SPI) += spi_fsl_spi.o
obj-$(CONFIG_SPI_PPC4xx) += spi_ppc4xx.o
obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o
obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx_hw.o
obj-$(CONFIG_SPI_S3C64XX) += spi_s3c64xx.o
obj-$(CONFIG_SPI_TEGRA) += spi_tegra.o
obj-$(CONFIG_SPI_TOPCLIFF_PCH) += spi_topcliff_pch.o
obj-$(CONFIG_SPI_TXX9) += spi_txx9.o
obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o
obj-$(CONFIG_SPI_XILINX_OF) += xilinx_spi_of.o
obj-$(CONFIG_SPI_XILINX_PLTFM) += xilinx_spi_pltfm.o
obj-$(CONFIG_SPI_SH_SCI) += spi_sh_sci.o
obj-$(CONFIG_SPI_SH_MSIOF) += spi_sh_msiof.o
obj-$(CONFIG_SPI_STMP3XXX) += spi_stmp.o
obj-$(CONFIG_SPI_NUC900) += spi_nuc900.o
# special build for s3c24xx spi driver with fiq support
spi_s3c24xx_hw-y := spi_s3c24xx.o
spi_s3c24xx_hw-$(CONFIG_SPI_S3C24XX_FIQ) += spi_s3c24xx_fiq.o
# ... add above this line ...
# SPI protocol drivers (device/link on bus)
obj-$(CONFIG_SPI_SPIDEV) += spidev.o
obj-$(CONFIG_SPI_TLE62X0) += tle62x0.o
# ... add above this line ...
# SPI slave controller drivers (upstream link)
# ... add above this line ...
# SPI slave drivers (protocol for that link)
# ... add above this line ...