forked from Minki/linux
3707873299
This adds an initial DT file for the Globalscale D3Plug with Dove SoC. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
104 lines
1.8 KiB
Plaintext
104 lines
1.8 KiB
Plaintext
/dts-v1/;
|
|
|
|
#include "dove.dtsi"
|
|
|
|
/ {
|
|
model = "Globalscale D3Plug";
|
|
compatible = "globalscale,d3plug", "marvell,dove";
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0x00000000 0x40000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p2 rw rootwait";
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>;
|
|
pinctrl-names = "default";
|
|
|
|
wlan-act {
|
|
label = "wlan-act";
|
|
gpios = <&gpio0 0 1>;
|
|
};
|
|
|
|
wlan-ap {
|
|
label = "wlan-ap";
|
|
gpios = <&gpio0 1 1>;
|
|
};
|
|
|
|
status {
|
|
label = "status";
|
|
gpios = <&gpio0 2 1>;
|
|
};
|
|
};
|
|
|
|
regulators {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
usb_power: regulator@1 {
|
|
compatible = "regulator-fixed";
|
|
reg = <1>;
|
|
regulator-name = "USB Power";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
gpio = <&gpio0 8 0>;
|
|
pinctrl-0 = <&pmx_gpio_8>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart0 { status = "okay"; };
|
|
&sata0 { status = "okay"; };
|
|
&i2c0 { status = "okay"; };
|
|
|
|
/* Samsung M8G2F eMMC */
|
|
&sdio0 {
|
|
status = "okay";
|
|
non-removable;
|
|
bus-width = <4>;
|
|
};
|
|
|
|
/* Marvell SD8787 WLAN/BT */
|
|
&sdio1 {
|
|
status = "okay";
|
|
non-removable;
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
/* spi0.0: 2M Flash Macronix MX25L1605D */
|
|
spi-flash@0 {
|
|
compatible = "st,m25l1605d";
|
|
spi-max-frequency = <86000000>;
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
/* Fresco Logic USB3.0 xHCI controller */
|
|
pcie-port@0 {
|
|
status = "okay";
|
|
reset-gpios = <&gpio0 26 1>;
|
|
reset-delay-us = <20000>;
|
|
pinctrl-0 = <&pmx_camera_gpio>;
|
|
pinctrl-names = "default";
|
|
};
|
|
/* Mini-PCIe slot */
|
|
pcie-port@1 {
|
|
status = "okay";
|
|
reset-gpios = <&gpio0 25 1>;
|
|
};
|
|
};
|