forked from Minki/linux
e512448f6e
Add SATA PHY and SATA AHCI controller nodes to device tree to enable generic ahci support on the IPQ8064/AP148 board. Signed-off-by: Kumar Gala <galak@codeaurora.org>
94 lines
1.5 KiB
Plaintext
94 lines
1.5 KiB
Plaintext
#include "qcom-ipq8064-v1.0.dtsi"
|
|
|
|
/ {
|
|
model = "Qualcomm IPQ8064/AP148";
|
|
compatible = "qcom,ipq8064-ap148", "qcom,ipq8064";
|
|
|
|
reserved-memory {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
rsvd@41200000 {
|
|
reg = <0x41200000 0x300000>;
|
|
no-map;
|
|
};
|
|
};
|
|
|
|
soc {
|
|
pinmux@800000 {
|
|
i2c4_pins: i2c4_pinmux {
|
|
pins = "gpio12", "gpio13";
|
|
function = "gsbi4";
|
|
bias-disable;
|
|
};
|
|
|
|
spi_pins: spi_pins {
|
|
mux {
|
|
pins = "gpio18", "gpio19", "gpio21";
|
|
function = "gsbi5";
|
|
drive-strength = <10>;
|
|
bias-none;
|
|
};
|
|
};
|
|
};
|
|
|
|
gsbi@16300000 {
|
|
qcom,mode = <GSBI_PROT_I2C_UART>;
|
|
status = "ok";
|
|
serial@16340000 {
|
|
status = "ok";
|
|
};
|
|
|
|
i2c4: i2c@16380000 {
|
|
status = "ok";
|
|
|
|
clock-frequency = <200000>;
|
|
|
|
pinctrl-0 = <&i2c4_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|
|
|
|
gsbi5: gsbi@1a200000 {
|
|
qcom,mode = <GSBI_PROT_SPI>;
|
|
status = "ok";
|
|
|
|
spi4: spi@1a280000 {
|
|
status = "ok";
|
|
spi-max-frequency = <50000000>;
|
|
|
|
pinctrl-0 = <&spi_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
cs-gpios = <&qcom_pinmux 20 0>;
|
|
|
|
flash: m25p80@0 {
|
|
compatible = "s25fl256s1";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
spi-max-frequency = <50000000>;
|
|
reg = <0>;
|
|
|
|
partition@0 {
|
|
label = "rootfs";
|
|
reg = <0x0 0x1000000>;
|
|
};
|
|
|
|
partition@1 {
|
|
label = "scratch";
|
|
reg = <0x1000000 0x1000000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
sata-phy@1b400000 {
|
|
status = "ok";
|
|
};
|
|
|
|
sata@29000000 {
|
|
status = "ok";
|
|
};
|
|
};
|
|
};
|