forked from Minki/linux
ce5abbb816
Add HS USB Host support along with USB PHYs and power supply regulators Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
111 lines
2.5 KiB
Plaintext
111 lines
2.5 KiB
Plaintext
/*
|
|
* Common support for CompuLab CM-T3x CoMs
|
|
*/
|
|
|
|
/ {
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0x80000000 0x10000000>; /* 256 MB */
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&green_led_pins>;
|
|
ledb {
|
|
label = "cm-t3x:green";
|
|
gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>; /* gpio186 */
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
};
|
|
|
|
/* HS USB Port 1 Power */
|
|
hsusb1_power: hsusb1_power_reg {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "hsusb1_vbus";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
startup-delay-us = <70000>;
|
|
};
|
|
|
|
/* HS USB Port 2 Power */
|
|
hsusb2_power: hsusb2_power_reg {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "hsusb2_vbus";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
startup-delay-us = <70000>;
|
|
};
|
|
|
|
/* HS USB Host PHY on PORT 1 */
|
|
hsusb1_phy: hsusb1_phy {
|
|
compatible = "usb-nop-xceiv";
|
|
vcc-supply = <&hsusb1_power>;
|
|
};
|
|
|
|
/* HS USB Host PHY on PORT 2 */
|
|
hsusb2_phy: hsusb2_phy {
|
|
compatible = "usb-nop-xceiv";
|
|
vcc-supply = <&hsusb2_power>;
|
|
};
|
|
};
|
|
|
|
&omap3_pmx_core {
|
|
|
|
uart3_pins: pinmux_uart3_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
|
|
OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
|
|
>;
|
|
};
|
|
|
|
mmc1_pins: pinmux_mmc1_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
|
|
OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
|
|
OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
|
|
OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
|
|
OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
|
|
OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
|
|
>;
|
|
};
|
|
|
|
green_led_pins: pinmux_green_led_pins {
|
|
pinctrl-single,pins = <
|
|
OMAP3_CORE1_IOPAD(0x21e2, PIN_OUTPUT | MUX_MODE4) /* sys_clkout2.gpio_186 */
|
|
>;
|
|
};
|
|
};
|
|
|
|
&uart3 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart3_pins>;
|
|
};
|
|
|
|
&mmc1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc1_pins>;
|
|
bus-width = <4>;
|
|
};
|
|
|
|
&mmc3 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&i2c1 {
|
|
clock-frequency = <400000>;
|
|
};
|
|
|
|
&i2c3 {
|
|
clock-frequency = <400000>;
|
|
};
|
|
&usbhshost {
|
|
port1-mode = "ehci-phy";
|
|
port2-mode = "ehci-phy";
|
|
};
|
|
|
|
&usbhsehci {
|
|
phys = <&hsusb1_phy &hsusb2_phy>;
|
|
};
|