forked from Minki/linux
2992714d43
This fixes "Too few good blocks within range" issues on GoFlex Net by setting chip-delay to 40. The basic problem was discussed at http://forum.doozan.com/read.php?2,7451 Signed-off-by: Eric Hutter <hutter.eric@gmail.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Cc: <stable@vger.kernel.org> # v3.6.x Signed-off-by: Jason Cooper <jason@lakedaemon.net>
173 lines
3.5 KiB
Plaintext
173 lines
3.5 KiB
Plaintext
/dts-v1/;
|
|
|
|
/include/ "kirkwood.dtsi"
|
|
/include/ "kirkwood-6281.dtsi"
|
|
|
|
/ {
|
|
model = "Seagate GoFlex Net";
|
|
compatible = "seagate,goflexnet", "marvell,kirkwood-88f6281", "marvell,kirkwood";
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0x00000000 0x8000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
|
|
};
|
|
|
|
ocp@f1000000 {
|
|
pinctrl: pinctrl@10000 {
|
|
|
|
pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
|
|
&pmx_led_left_cap_0 &pmx_led_left_cap_1
|
|
&pmx_led_left_cap_2 &pmx_led_left_cap_3
|
|
&pmx_led_right_cap_0 &pmx_led_right_cap_1
|
|
&pmx_led_right_cap_2 &pmx_led_right_cap_3
|
|
>;
|
|
pinctrl-names = "default";
|
|
|
|
pmx_usb_power_enable: pmx-usb-power-enable {
|
|
marvell,pins = "mpp29";
|
|
marvell,function = "gpio";
|
|
};
|
|
pmx_led_right_cap_0: pmx-led_right_cap_0 {
|
|
marvell,pins = "mpp38";
|
|
marvell,function = "gpio";
|
|
};
|
|
pmx_led_right_cap_1: pmx-led_right_cap_1 {
|
|
marvell,pins = "mpp39";
|
|
marvell,function = "gpio";
|
|
};
|
|
pmx_led_right_cap_2: pmx-led_right_cap_2 {
|
|
marvell,pins = "mpp40";
|
|
marvell,function = "gpio";
|
|
};
|
|
pmx_led_right_cap_3: pmx-led_right_cap_3 {
|
|
marvell,pins = "mpp41";
|
|
marvell,function = "gpio";
|
|
};
|
|
pmx_led_left_cap_0: pmx-led_left_cap_0 {
|
|
marvell,pins = "mpp42";
|
|
marvell,function = "gpio";
|
|
};
|
|
pmx_led_left_cap_1: pmx-led_left_cap_1 {
|
|
marvell,pins = "mpp43";
|
|
marvell,function = "gpio";
|
|
};
|
|
pmx_led_left_cap_2: pmx-led_left_cap_2 {
|
|
marvell,pins = "mpp44";
|
|
marvell,function = "gpio";
|
|
};
|
|
pmx_led_left_cap_3: pmx-led_left_cap_3 {
|
|
marvell,pins = "mpp45";
|
|
marvell,function = "gpio";
|
|
};
|
|
pmx_led_green: pmx-led_green {
|
|
marvell,pins = "mpp46";
|
|
marvell,function = "gpio";
|
|
};
|
|
pmx_led_orange: pmx-led_orange {
|
|
marvell,pins = "mpp47";
|
|
marvell,function = "gpio";
|
|
};
|
|
};
|
|
serial@12000 {
|
|
status = "ok";
|
|
};
|
|
|
|
nand@3000000 {
|
|
chip-delay = <40>;
|
|
status = "okay";
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0000000 0x100000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@100000 {
|
|
label = "uImage";
|
|
reg = <0x0100000 0x400000>;
|
|
};
|
|
|
|
partition@500000 {
|
|
label = "pogoplug";
|
|
reg = <0x0500000 0x2000000>;
|
|
};
|
|
|
|
partition@2500000 {
|
|
label = "root";
|
|
reg = <0x02500000 0xd800000>;
|
|
};
|
|
};
|
|
sata@80000 {
|
|
status = "okay";
|
|
nr-ports = <2>;
|
|
};
|
|
|
|
};
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
health {
|
|
label = "status:green:health";
|
|
gpios = <&gpio1 14 1>;
|
|
linux,default-trigger = "default-on";
|
|
};
|
|
fault {
|
|
label = "status:orange:fault";
|
|
gpios = <&gpio1 15 1>;
|
|
};
|
|
left0 {
|
|
label = "status:white:left0";
|
|
gpios = <&gpio1 10 0>;
|
|
};
|
|
left1 {
|
|
label = "status:white:left1";
|
|
gpios = <&gpio1 11 0>;
|
|
};
|
|
left2 {
|
|
label = "status:white:left2";
|
|
gpios = <&gpio1 12 0>;
|
|
};
|
|
left3 {
|
|
label = "status:white:left3";
|
|
gpios = <&gpio1 13 0>;
|
|
};
|
|
right0 {
|
|
label = "status:white:right0";
|
|
gpios = <&gpio1 6 0>;
|
|
};
|
|
right1 {
|
|
label = "status:white:right1";
|
|
gpios = <&gpio1 7 0>;
|
|
};
|
|
right2 {
|
|
label = "status:white:right2";
|
|
gpios = <&gpio1 8 0>;
|
|
};
|
|
right3 {
|
|
label = "status:white:right3";
|
|
gpios = <&gpio1 9 0>;
|
|
};
|
|
};
|
|
regulators {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
usb_power: regulator@1 {
|
|
compatible = "regulator-fixed";
|
|
reg = <1>;
|
|
regulator-name = "USB Power";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
gpio = <&gpio0 29 0>;
|
|
};
|
|
};
|
|
};
|