forked from Minki/linux
a8de5ce989
Spelling fixes in arch/ppc/. Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Paul Mackerras <paulus@samba.org>
301 lines
8.7 KiB
C
301 lines
8.7 KiB
C
/*
|
|
* Motorola MCG Harrier northbridge/memory controller support
|
|
*
|
|
* Author: Dale Farnsworth
|
|
* dale.farnsworth@mvista.com
|
|
*
|
|
* 2001 (c) MontaVista, Software, Inc. This file is licensed under
|
|
* the terms of the GNU General Public License version 2. This program
|
|
* is licensed "as is" without any warranty of any kind, whether express
|
|
* or implied.
|
|
*/
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/harrier_defs.h>
|
|
|
|
#include <asm/byteorder.h>
|
|
#include <asm/io.h>
|
|
#include <asm/irq.h>
|
|
#include <asm/pci.h>
|
|
#include <asm/pci-bridge.h>
|
|
#include <asm/open_pic.h>
|
|
#include <asm/harrier.h>
|
|
|
|
/* define defaults for inbound windows */
|
|
#define HARRIER_ITAT_DEFAULT (HARRIER_ITAT_ENA | \
|
|
HARRIER_ITAT_MEM | \
|
|
HARRIER_ITAT_WPE | \
|
|
HARRIER_ITAT_GBL)
|
|
|
|
#define HARRIER_MPAT_DEFAULT (HARRIER_ITAT_ENA | \
|
|
HARRIER_ITAT_MEM | \
|
|
HARRIER_ITAT_WPE | \
|
|
HARRIER_ITAT_GBL)
|
|
|
|
/*
|
|
* Initialize the inbound window size on a non-monarch harrier.
|
|
*/
|
|
void __init harrier_setup_nonmonarch(uint ppc_reg_base, uint in0_size)
|
|
{
|
|
u16 temps;
|
|
u32 temp;
|
|
|
|
if (in0_size > HARRIER_ITSZ_2GB) {
|
|
printk
|
|
("harrier_setup_nonmonarch: Invalid window size code %d\n",
|
|
in0_size);
|
|
return;
|
|
}
|
|
|
|
/* Clear the PCI memory enable bit. If we don't, then when the
|
|
* inbound windows are enabled below, the corresponding BARs will be
|
|
* "live" and start answering to PCI memory reads from their default
|
|
* addresses (0x0), which overlap with system RAM.
|
|
*/
|
|
temps = in_le16((u16 *) (ppc_reg_base +
|
|
HARRIER_XCSR_CONFIG(PCI_COMMAND)));
|
|
temps &= ~(PCI_COMMAND_MEMORY);
|
|
out_le16((u16 *) (ppc_reg_base + HARRIER_XCSR_CONFIG(PCI_COMMAND)),
|
|
temps);
|
|
|
|
/* Setup a non-prefetchable inbound window */
|
|
out_le32((u32 *) (ppc_reg_base +
|
|
HARRIER_XCSR_CONFIG(HARRIER_ITSZ0_OFF)), in0_size);
|
|
|
|
temp = in_le32((u32 *) (ppc_reg_base +
|
|
HARRIER_XCSR_CONFIG(HARRIER_ITAT0_OFF)));
|
|
temp &= ~HARRIER_ITAT_PRE;
|
|
temp |= HARRIER_ITAT_DEFAULT;
|
|
out_le32((u32 *) (ppc_reg_base +
|
|
HARRIER_XCSR_CONFIG(HARRIER_ITAT0_OFF)), temp);
|
|
|
|
/* Enable the message passing block */
|
|
temp = in_le32((u32 *) (ppc_reg_base +
|
|
HARRIER_XCSR_CONFIG(HARRIER_MPAT_OFF)));
|
|
temp |= HARRIER_MPAT_DEFAULT;
|
|
out_le32((u32 *) (ppc_reg_base +
|
|
HARRIER_XCSR_CONFIG(HARRIER_MPAT_OFF)), temp);
|
|
}
|
|
|
|
void __init harrier_release_eready(uint ppc_reg_base)
|
|
{
|
|
ulong temp;
|
|
|
|
/*
|
|
* Set EREADY to allow the line to be pulled up after everyone is
|
|
* ready.
|
|
*/
|
|
temp = in_be32((uint *) (ppc_reg_base + HARRIER_MISC_CSR_OFF));
|
|
temp |= HARRIER_EREADY;
|
|
out_be32((uint *) (ppc_reg_base + HARRIER_MISC_CSR_OFF), temp);
|
|
}
|
|
|
|
void __init harrier_wait_eready(uint ppc_reg_base)
|
|
{
|
|
ulong temp;
|
|
|
|
/*
|
|
* Poll the ERDYS line until it goes high to indicate that all
|
|
* non-monarch PrPMCs are ready for bus enumeration (or that there are
|
|
* no PrPMCs present).
|
|
*/
|
|
|
|
/* FIXME: Add a timeout of some kind to prevent endless waits. */
|
|
do {
|
|
|
|
temp = in_be32((uint *) (ppc_reg_base + HARRIER_MISC_CSR_OFF));
|
|
|
|
} while (!(temp & HARRIER_ERDYS));
|
|
}
|
|
|
|
/*
|
|
* Initialize the Motorola MCG Harrier host bridge.
|
|
*
|
|
* This means setting up the PPC bus to PCI memory and I/O space mappings,
|
|
* setting the PCI memory space address of the MPIC (mapped straight
|
|
* through), and ioremap'ing the mpic registers.
|
|
* 'OpenPIC_Addr' will be set correctly by this routine.
|
|
* This routine will not change the PCI_CONFIG_ADDR or PCI_CONFIG_DATA
|
|
* addresses and assumes that the mapping of PCI memory space back to system
|
|
* memory is set up correctly by PPCBug.
|
|
*/
|
|
int __init
|
|
harrier_init(struct pci_controller *hose,
|
|
uint ppc_reg_base,
|
|
ulong processor_pci_mem_start,
|
|
ulong processor_pci_mem_end,
|
|
ulong processor_pci_io_start,
|
|
ulong processor_pci_io_end, ulong processor_mpic_base)
|
|
{
|
|
uint addr, offset;
|
|
|
|
/*
|
|
* Some sanity checks...
|
|
*/
|
|
if (((processor_pci_mem_start & 0xffff0000) != processor_pci_mem_start)
|
|
|| ((processor_pci_io_start & 0xffff0000) !=
|
|
processor_pci_io_start)) {
|
|
printk("harrier_init: %s\n",
|
|
"PPC to PCI mappings must start on 64 KB boundaries");
|
|
return -1;
|
|
}
|
|
|
|
if (((processor_pci_mem_end & 0x0000ffff) != 0x0000ffff) ||
|
|
((processor_pci_io_end & 0x0000ffff) != 0x0000ffff)) {
|
|
printk("harrier_init: PPC to PCI mappings %s\n",
|
|
"must end just before a 64 KB boundaries");
|
|
return -1;
|
|
}
|
|
|
|
if (((processor_pci_mem_end - processor_pci_mem_start) !=
|
|
(hose->mem_space.end - hose->mem_space.start)) ||
|
|
((processor_pci_io_end - processor_pci_io_start) !=
|
|
(hose->io_space.end - hose->io_space.start))) {
|
|
printk("harrier_init: %s\n",
|
|
"PPC and PCI memory or I/O space sizes don't match");
|
|
return -1;
|
|
}
|
|
|
|
if ((processor_mpic_base & 0xfffc0000) != processor_mpic_base) {
|
|
printk("harrier_init: %s\n",
|
|
"MPIC address must start on 256 KB boundary");
|
|
return -1;
|
|
}
|
|
|
|
if ((pci_dram_offset & 0xffff0000) != pci_dram_offset) {
|
|
printk("harrier_init: %s\n",
|
|
"pci_dram_offset must be multiple of 64 KB");
|
|
return -1;
|
|
}
|
|
|
|
/*
|
|
* Program the OTAD/OTOF registers to set up the PCI Mem & I/O
|
|
* space mappings. These are the mappings going from the processor to
|
|
* the PCI bus.
|
|
*
|
|
* Note: Don't need to 'AND' start/end addresses with 0xffff0000
|
|
* because sanity check above ensures that they are properly
|
|
* aligned.
|
|
*/
|
|
|
|
/* Set up PPC->PCI Mem mapping */
|
|
addr = processor_pci_mem_start | (processor_pci_mem_end >> 16);
|
|
#ifdef CONFIG_HARRIER_STORE_GATHERING
|
|
offset = (hose->mem_space.start - processor_pci_mem_start) | 0x9a;
|
|
#else
|
|
offset = (hose->mem_space.start - processor_pci_mem_start) | 0x92;
|
|
#endif
|
|
out_be32((uint *) (ppc_reg_base + HARRIER_OTAD0_OFF), addr);
|
|
out_be32((uint *) (ppc_reg_base + HARRIER_OTOF0_OFF), offset);
|
|
|
|
/* Set up PPC->PCI I/O mapping -- Contiguous I/O space */
|
|
addr = processor_pci_io_start | (processor_pci_io_end >> 16);
|
|
offset = (hose->io_space.start - processor_pci_io_start) | 0x80;
|
|
out_be32((uint *) (ppc_reg_base + HARRIER_OTAD1_OFF), addr);
|
|
out_be32((uint *) (ppc_reg_base + HARRIER_OTOF1_OFF), offset);
|
|
|
|
/* Enable MPIC */
|
|
OpenPIC_Addr = (void *)processor_mpic_base;
|
|
addr = (processor_mpic_base >> 16) | 1;
|
|
out_be16((ushort *) (ppc_reg_base + HARRIER_MBAR_OFF), addr);
|
|
out_8((u_char *) (ppc_reg_base + HARRIER_MPIC_CSR_OFF),
|
|
HARRIER_MPIC_OPI_ENABLE);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Find the amount of RAM present.
|
|
* This assumes that PPCBug has initialized the memory controller (SMC)
|
|
* on the Harrier correctly (i.e., it does no sanity checking).
|
|
* It also assumes that the memory base registers are set to configure the
|
|
* memory as contiguous starting with "RAM A BASE", "RAM B BASE", etc.
|
|
* however, RAM base registers can be skipped (e.g. A, B, C are set,
|
|
* D is skipped but E is set is okay).
|
|
*/
|
|
#define MB (1024*1024UL)
|
|
|
|
static uint harrier_size_table[] __initdata = {
|
|
0 * MB, /* 0 ==> 0 MB */
|
|
32 * MB, /* 1 ==> 32 MB */
|
|
64 * MB, /* 2 ==> 64 MB */
|
|
64 * MB, /* 3 ==> 64 MB */
|
|
128 * MB, /* 4 ==> 128 MB */
|
|
128 * MB, /* 5 ==> 128 MB */
|
|
128 * MB, /* 6 ==> 128 MB */
|
|
256 * MB, /* 7 ==> 256 MB */
|
|
256 * MB, /* 8 ==> 256 MB */
|
|
256 * MB, /* 9 ==> 256 MB */
|
|
512 * MB, /* a ==> 512 MB */
|
|
512 * MB, /* b ==> 512 MB */
|
|
512 * MB, /* c ==> 512 MB */
|
|
1024 * MB, /* d ==> 1024 MB */
|
|
1024 * MB, /* e ==> 1024 MB */
|
|
2048 * MB, /* f ==> 2048 MB */
|
|
};
|
|
|
|
/*
|
|
* *** WARNING: You MUST have a BAT set up to map in the XCSR regs ***
|
|
*
|
|
* Read the memory controller's registers to determine the amount of system
|
|
* memory. Assumes that the memory controller registers are already mapped
|
|
* into virtual memory--too early to use ioremap().
|
|
*/
|
|
unsigned long __init harrier_get_mem_size(uint xcsr_base)
|
|
{
|
|
ulong last_addr;
|
|
int i;
|
|
uint vend_dev_id;
|
|
uint *size_table;
|
|
uint val;
|
|
uint *csrp;
|
|
uint size;
|
|
int size_table_entries;
|
|
|
|
vend_dev_id = in_be32((uint *) xcsr_base + PCI_VENDOR_ID);
|
|
|
|
if (((vend_dev_id & 0xffff0000) >> 16) != PCI_VENDOR_ID_MOTOROLA) {
|
|
printk("harrier_get_mem_size: %s (0x%x)\n",
|
|
"Not a Motorola Memory Controller", vend_dev_id);
|
|
return 0;
|
|
}
|
|
|
|
vend_dev_id &= 0x0000ffff;
|
|
|
|
if (vend_dev_id == PCI_DEVICE_ID_MOTOROLA_HARRIER) {
|
|
size_table = harrier_size_table;
|
|
size_table_entries = sizeof(harrier_size_table) /
|
|
sizeof(harrier_size_table[0]);
|
|
} else {
|
|
printk("harrier_get_mem_size: %s (0x%x)\n",
|
|
"Not a Harrier", vend_dev_id);
|
|
return 0;
|
|
}
|
|
|
|
last_addr = 0;
|
|
|
|
csrp = (uint *) (xcsr_base + HARRIER_SDBA_OFF);
|
|
for (i = 0; i < 8; i++) {
|
|
val = in_be32(csrp++);
|
|
|
|
if (val & 0x100) { /* If enabled */
|
|
size = val >> HARRIER_SDB_SIZE_SHIFT;
|
|
size &= HARRIER_SDB_SIZE_MASK;
|
|
if (size >= size_table_entries) {
|
|
break; /* Register not set correctly */
|
|
}
|
|
size = size_table[size];
|
|
|
|
val &= ~(size - 1);
|
|
val += size;
|
|
|
|
if (val > last_addr) {
|
|
last_addr = val;
|
|
}
|
|
}
|
|
}
|
|
|
|
return last_addr;
|
|
}
|