linux/Documentation/aoe/aoe.txt
Lucas De Marchi 970e248649 Documentation: remove references to /etc/modprobe.conf
Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.

There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-03-30 16:03:15 -07:00

124 lines
4.5 KiB
Plaintext

The EtherDrive (R) HOWTO for users of 2.6 kernels is found at ...
http://www.coraid.com/SUPPORT/EtherDrive-HBA
It has many tips and hints!
The aoetools are userland programs that are designed to work with this
driver. The aoetools are on sourceforge.
http://aoetools.sourceforge.net/
The scripts in this Documentation/aoe directory are intended to
document the use of the driver and are not necessary if you install
the aoetools.
CREATING DEVICE NODES
Users of udev should find the block device nodes created
automatically, but to create all the necessary device nodes, use the
udev configuration rules provided in udev.txt (in this directory).
There is a udev-install.sh script that shows how to install these
rules on your system.
If you are not using udev, two scripts are provided in
Documentation/aoe as examples of static device node creation for
using the aoe driver.
rm -rf /dev/etherd
sh Documentation/aoe/mkdevs.sh /dev/etherd
... or to make just one shelf's worth of block device nodes ...
sh Documentation/aoe/mkshelf.sh /dev/etherd 0
There is also an autoload script that shows how to edit
/etc/modprobe.d/aoe.conf to ensure that the aoe module is loaded when
necessary.
USING DEVICE NODES
"cat /dev/etherd/err" blocks, waiting for error diagnostic output,
like any retransmitted packets.
"echo eth2 eth4 > /dev/etherd/interfaces" tells the aoe driver to
limit ATA over Ethernet traffic to eth2 and eth4. AoE traffic from
untrusted networks should be ignored as a matter of security. See
also the aoe_iflist driver option described below.
"echo > /dev/etherd/discover" tells the driver to find out what AoE
devices are available.
These character devices may disappear and be replaced by sysfs
counterparts. Using the commands in aoetools insulates users from
these implementation details.
The block devices are named like this:
e{shelf}.{slot}
e{shelf}.{slot}p{part}
... so that "e0.2" is the third blade from the left (slot 2) in the
first shelf (shelf address zero). That's the whole disk. The first
partition on that disk would be "e0.2p1".
USING SYSFS
Each aoe block device in /sys/block has the extra attributes of
state, mac, and netif. The state attribute is "up" when the device
is ready for I/O and "down" if detected but unusable. The
"down,closewait" state shows that the device is still open and
cannot come up again until it has been closed.
The mac attribute is the ethernet address of the remote AoE device.
The netif attribute is the network interface on the localhost
through which we are communicating with the remote AoE device.
There is a script in this directory that formats this information
in a convenient way. Users with aoetools can use the aoe-stat
command.
root@makki root# sh Documentation/aoe/status.sh
e10.0 eth3 up
e10.1 eth3 up
e10.2 eth3 up
e10.3 eth3 up
e10.4 eth3 up
e10.5 eth3 up
e10.6 eth3 up
e10.7 eth3 up
e10.8 eth3 up
e10.9 eth3 up
e4.0 eth1 up
e4.1 eth1 up
e4.2 eth1 up
e4.3 eth1 up
e4.4 eth1 up
e4.5 eth1 up
e4.6 eth1 up
e4.7 eth1 up
e4.8 eth1 up
e4.9 eth1 up
Use /sys/module/aoe/parameters/aoe_iflist (or better, the driver
option discussed below) instead of /dev/etherd/interfaces to limit
AoE traffic to the network interfaces in the given
whitespace-separated list. Unlike the old character device, the
sysfs entry can be read from as well as written to.
It's helpful to trigger discovery after setting the list of allowed
interfaces. The aoetools package provides an aoe-discover script
for this purpose. You can also directly use the
/dev/etherd/discover special file described above.
DRIVER OPTIONS
There is a boot option for the built-in aoe driver and a
corresponding module parameter, aoe_iflist. Without this option,
all network interfaces may be used for ATA over Ethernet. Here is a
usage example for the module parameter.
modprobe aoe_iflist="eth1 eth3"