c96f8d3ca7
vdda1v1 and vdda1v8 supplies are required by USB PLL, not by the PHYs. Remove them from usbphyc child phy nodes now that they are managed in usbphyc parent node at SoC level. Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com> Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
148 lines
2.5 KiB
Plaintext
148 lines
2.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
|
|
/*
|
|
* Copyright (C) 2020 Marek Vasut <marex@denx.de>
|
|
*/
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/pwm/pwm.h>
|
|
|
|
/ {
|
|
aliases {
|
|
serial0 = &uart4;
|
|
serial1 = &usart3;
|
|
serial2 = &uart8;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
led {
|
|
compatible = "gpio-leds";
|
|
|
|
led-0 {
|
|
label = "yellow:led";
|
|
gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
};
|
|
};
|
|
|
|
&adc {
|
|
status = "disabled";
|
|
};
|
|
|
|
&dac {
|
|
status = "disabled";
|
|
};
|
|
|
|
&fmc {
|
|
status = "disabled";
|
|
};
|
|
|
|
&gpioa {
|
|
/*
|
|
* NOTE: The USB Port on the PicoITX needs a PWR_EN signal to enable
|
|
* port power. This signal should be handled by USB power sequencing
|
|
* in order to turn on port power when USB bus is powered up, but so
|
|
* far there is no such functionality.
|
|
*/
|
|
usb-port-power-hog {
|
|
gpio-hog;
|
|
gpios = <13 0>;
|
|
output-low;
|
|
line-name = "usb-port-power";
|
|
};
|
|
};
|
|
|
|
&gpioc {
|
|
gpio-line-names = "", "", "", "",
|
|
"", "", "In1", "",
|
|
"", "", "", "",
|
|
"", "", "", "";
|
|
};
|
|
|
|
&gpiod {
|
|
gpio-line-names = "", "", "", "",
|
|
"", "", "", "",
|
|
"", "", "", "Out1",
|
|
"Out2", "", "", "";
|
|
};
|
|
|
|
&gpiog {
|
|
gpio-line-names = "In2", "", "", "",
|
|
"", "", "", "",
|
|
"", "", "", "",
|
|
"", "", "", "";
|
|
};
|
|
|
|
&i2c2 { /* On board-to-board connector (optional) */
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2c2_pins_a>;
|
|
i2c-scl-rising-time-ns = <185>;
|
|
i2c-scl-falling-time-ns = <20>;
|
|
status = "okay";
|
|
/* spare dmas for other usage */
|
|
/delete-property/dmas;
|
|
/delete-property/dma-names;
|
|
};
|
|
|
|
&i2c5 { /* On board-to-board connector */
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2c5_pins_a>;
|
|
i2c-scl-rising-time-ns = <185>;
|
|
i2c-scl-falling-time-ns = <20>;
|
|
status = "okay";
|
|
/* spare dmas for other usage */
|
|
/delete-property/dmas;
|
|
/delete-property/dma-names;
|
|
};
|
|
|
|
&ksz8851 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&usart3 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&usart3_pins_a>;
|
|
status = "okay";
|
|
};
|
|
|
|
&uart8 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usbh_ehci {
|
|
phys = <&usbphyc_port0>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usbh_ohci {
|
|
phys = <&usbphyc_port0>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usbotg_hs {
|
|
dr_mode = "otg";
|
|
pinctrl-0 = <&usbotg_hs_pins_a>;
|
|
pinctrl-names = "default";
|
|
phy-names = "usb2-phy";
|
|
phys = <&usbphyc_port1 0>;
|
|
vbus-supply = <&vbus_otg>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usbphyc {
|
|
status = "okay";
|
|
};
|
|
|
|
&usbphyc_port0 {
|
|
phy-supply = <&vdd_usb>;
|
|
};
|
|
|
|
&usbphyc_port1 {
|
|
phy-supply = <&vdd_usb>;
|
|
};
|