forked from Minki/linux
99db46ea29
For ipcmni_extend mode, the sequence number space is only 7 bits. So
the chance of id reuse is relatively high compared with the non-extended
mode.
To alleviate this id reuse problem, this patch enables cyclic allocation
for the index to the radix tree (idx). The disadvantage is that this
can cause a slight slow-down of the fast path, as the radix tree could
be higher than necessary.
To limit the radix tree height, I have chosen the following limits:
1) The cycling is done over in_use*1.5.
2) At least, the cycling is done over
"normal" ipcnmi mode: RADIX_TREE_MAP_SIZE elements
"ipcmni_extended": 4096 elements
Result:
- for normal mode:
No change for <= 42 active ipc elements. With more than 42
active ipc elements, a 2nd level would be added to the radix
tree.
Without cyclic allocation, a 2nd level would be added only with
more than 63 active elements.
- for extended mode:
Cycling creates always at least a 2-level radix tree.
With more than 2730 active objects, a 3rd level would be
added, instead of > 4095 active objects until the 3rd level
is added without cyclic allocation.
For a 2-level radix tree compared to a 1-level radix tree, I have
observed < 1% performance impact.
Notes:
1) Normal "x=semget();y=semget();" is unaffected: Then the idx
is e.g. a and a+1, regardless if idr_alloc() or idr_alloc_cyclic()
is used.
2) The -1% happens in a microbenchmark after this situation:
x=semget();
for(i=0;i<4000;i++) {t=semget();semctl(t,0,IPC_RMID);}
y=semget();
Now perform semget calls on x and y that do not sleep.
3) The worst-case reuse cycle time is unfortunately unaffected:
If you have 2^24-1 ipc objects allocated, and get/remove the last
possible element in a loop, then the id is reused after 128
get/remove pairs.
Performance check:
A microbenchmark that performes no-op semop() randomly on two IDs,
with only these two IDs allocated.
The IDs were set using /proc/sys/kernel/sem_next_id.
The test was run 5 times, averages are shown.
1 & 2: Base (6.22 seconds for 10.000.000 semops)
1 & 40: -0.2%
1 & 3348: - 0.8%
1 & 27348: - 1.6%
1 & 15777204: - 3.2%
Or: ~12.6 cpu cycles per additional radix tree level.
The cpu is an Intel I3-5010U. ~1300 cpu cycles/syscall is slower
than what I remember (spectre impact?).
V2 of the patch:
- use "min" and "max"
- use RADIX_TREE_MAP_SIZE * RADIX_TREE_MAP_SIZE instead of
(2<<12).
[akpm@linux-foundation.org: fix max() warning]
Link: http://lkml.kernel.org/r/20190329204930.21620-3-longman@redhat.com
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Acked-by: Waiman Long <longman@redhat.com>
Cc: "Luis R. Rodriguez" <mcgrof@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: "Eric W . Biederman" <ebiederm@xmission.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
||
|---|---|---|
| .. | ||
| compat.c | ||
| ipc_sysctl.c | ||
| Makefile | ||
| mq_sysctl.c | ||
| mqueue.c | ||
| msg.c | ||
| msgutil.c | ||
| namespace.c | ||
| sem.c | ||
| shm.c | ||
| syscall.c | ||
| util.c | ||
| util.h | ||