forked from Minki/linux
9979dbe515
The mmc_execute_tuning() has already prepared the opcode, there is no need to prepare it again at mmc_send_tuning(), and, there is a BUG of mmc_send_tuning() to determine the opcode by bus width, assume eMMC was running at HS200, 4bit mode, then the mmc_send_tuning() will overwrite the opcode from CMD21 to CMD19, then got error. in addition, extend an argument of "cmd_error" to allow getting if there was cmd error when tune response. Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> [Ulf: Rebased patch] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
599 lines
17 KiB
C
599 lines
17 KiB
C
/*
|
|
* drivers/mmc/host/sdhci-msm.c - Qualcomm SDHCI Platform driver
|
|
*
|
|
* Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 and
|
|
* only version 2 as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/mmc/mmc.h>
|
|
#include <linux/slab.h>
|
|
|
|
#include "sdhci-pltfm.h"
|
|
|
|
#define CORE_MCI_VERSION 0x50
|
|
#define CORE_VERSION_MAJOR_SHIFT 28
|
|
#define CORE_VERSION_MAJOR_MASK (0xf << CORE_VERSION_MAJOR_SHIFT)
|
|
#define CORE_VERSION_MINOR_MASK 0xff
|
|
|
|
#define CORE_HC_MODE 0x78
|
|
#define HC_MODE_EN 0x1
|
|
#define CORE_POWER 0x0
|
|
#define CORE_SW_RST BIT(7)
|
|
|
|
#define MAX_PHASES 16
|
|
#define CORE_DLL_LOCK BIT(7)
|
|
#define CORE_DLL_EN BIT(16)
|
|
#define CORE_CDR_EN BIT(17)
|
|
#define CORE_CK_OUT_EN BIT(18)
|
|
#define CORE_CDR_EXT_EN BIT(19)
|
|
#define CORE_DLL_PDN BIT(29)
|
|
#define CORE_DLL_RST BIT(30)
|
|
#define CORE_DLL_CONFIG 0x100
|
|
#define CORE_DLL_STATUS 0x108
|
|
|
|
#define CORE_VENDOR_SPEC 0x10c
|
|
#define CORE_CLK_PWRSAVE BIT(1)
|
|
|
|
#define CORE_VENDOR_SPEC_CAPABILITIES0 0x11c
|
|
|
|
#define CDR_SELEXT_SHIFT 20
|
|
#define CDR_SELEXT_MASK (0xf << CDR_SELEXT_SHIFT)
|
|
#define CMUX_SHIFT_PHASE_SHIFT 24
|
|
#define CMUX_SHIFT_PHASE_MASK (7 << CMUX_SHIFT_PHASE_SHIFT)
|
|
|
|
struct sdhci_msm_host {
|
|
struct platform_device *pdev;
|
|
void __iomem *core_mem; /* MSM SDCC mapped address */
|
|
struct clk *clk; /* main SD/MMC bus clock */
|
|
struct clk *pclk; /* SDHC peripheral bus clock */
|
|
struct clk *bus_clk; /* SDHC bus voter clock */
|
|
struct mmc_host *mmc;
|
|
struct sdhci_pltfm_data sdhci_msm_pdata;
|
|
};
|
|
|
|
/* Platform specific tuning */
|
|
static inline int msm_dll_poll_ck_out_en(struct sdhci_host *host, u8 poll)
|
|
{
|
|
u32 wait_cnt = 50;
|
|
u8 ck_out_en;
|
|
struct mmc_host *mmc = host->mmc;
|
|
|
|
/* Poll for CK_OUT_EN bit. max. poll time = 50us */
|
|
ck_out_en = !!(readl_relaxed(host->ioaddr + CORE_DLL_CONFIG) &
|
|
CORE_CK_OUT_EN);
|
|
|
|
while (ck_out_en != poll) {
|
|
if (--wait_cnt == 0) {
|
|
dev_err(mmc_dev(mmc), "%s: CK_OUT_EN bit is not %d\n",
|
|
mmc_hostname(mmc), poll);
|
|
return -ETIMEDOUT;
|
|
}
|
|
udelay(1);
|
|
|
|
ck_out_en = !!(readl_relaxed(host->ioaddr + CORE_DLL_CONFIG) &
|
|
CORE_CK_OUT_EN);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int msm_config_cm_dll_phase(struct sdhci_host *host, u8 phase)
|
|
{
|
|
int rc;
|
|
static const u8 grey_coded_phase_table[] = {
|
|
0x0, 0x1, 0x3, 0x2, 0x6, 0x7, 0x5, 0x4,
|
|
0xc, 0xd, 0xf, 0xe, 0xa, 0xb, 0x9, 0x8
|
|
};
|
|
unsigned long flags;
|
|
u32 config;
|
|
struct mmc_host *mmc = host->mmc;
|
|
|
|
spin_lock_irqsave(&host->lock, flags);
|
|
|
|
config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
|
|
config &= ~(CORE_CDR_EN | CORE_CK_OUT_EN);
|
|
config |= (CORE_CDR_EXT_EN | CORE_DLL_EN);
|
|
writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
|
|
|
|
/* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '0' */
|
|
rc = msm_dll_poll_ck_out_en(host, 0);
|
|
if (rc)
|
|
goto err_out;
|
|
|
|
/*
|
|
* Write the selected DLL clock output phase (0 ... 15)
|
|
* to CDR_SELEXT bit field of DLL_CONFIG register.
|
|
*/
|
|
config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
|
|
config &= ~CDR_SELEXT_MASK;
|
|
config |= grey_coded_phase_table[phase] << CDR_SELEXT_SHIFT;
|
|
writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
|
|
|
|
/* Set CK_OUT_EN bit of DLL_CONFIG register to 1. */
|
|
writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
|
|
| CORE_CK_OUT_EN), host->ioaddr + CORE_DLL_CONFIG);
|
|
|
|
/* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '1' */
|
|
rc = msm_dll_poll_ck_out_en(host, 1);
|
|
if (rc)
|
|
goto err_out;
|
|
|
|
config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
|
|
config |= CORE_CDR_EN;
|
|
config &= ~CORE_CDR_EXT_EN;
|
|
writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
|
|
goto out;
|
|
|
|
err_out:
|
|
dev_err(mmc_dev(mmc), "%s: Failed to set DLL phase: %d\n",
|
|
mmc_hostname(mmc), phase);
|
|
out:
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
|
return rc;
|
|
}
|
|
|
|
/*
|
|
* Find out the greatest range of consecuitive selected
|
|
* DLL clock output phases that can be used as sampling
|
|
* setting for SD3.0 UHS-I card read operation (in SDR104
|
|
* timing mode) or for eMMC4.5 card read operation (in HS200
|
|
* timing mode).
|
|
* Select the 3/4 of the range and configure the DLL with the
|
|
* selected DLL clock output phase.
|
|
*/
|
|
|
|
static int msm_find_most_appropriate_phase(struct sdhci_host *host,
|
|
u8 *phase_table, u8 total_phases)
|
|
{
|
|
int ret;
|
|
u8 ranges[MAX_PHASES][MAX_PHASES] = { {0}, {0} };
|
|
u8 phases_per_row[MAX_PHASES] = { 0 };
|
|
int row_index = 0, col_index = 0, selected_row_index = 0, curr_max = 0;
|
|
int i, cnt, phase_0_raw_index = 0, phase_15_raw_index = 0;
|
|
bool phase_0_found = false, phase_15_found = false;
|
|
struct mmc_host *mmc = host->mmc;
|
|
|
|
if (!total_phases || (total_phases > MAX_PHASES)) {
|
|
dev_err(mmc_dev(mmc), "%s: Invalid argument: total_phases=%d\n",
|
|
mmc_hostname(mmc), total_phases);
|
|
return -EINVAL;
|
|
}
|
|
|
|
for (cnt = 0; cnt < total_phases; cnt++) {
|
|
ranges[row_index][col_index] = phase_table[cnt];
|
|
phases_per_row[row_index] += 1;
|
|
col_index++;
|
|
|
|
if ((cnt + 1) == total_phases) {
|
|
continue;
|
|
/* check if next phase in phase_table is consecutive or not */
|
|
} else if ((phase_table[cnt] + 1) != phase_table[cnt + 1]) {
|
|
row_index++;
|
|
col_index = 0;
|
|
}
|
|
}
|
|
|
|
if (row_index >= MAX_PHASES)
|
|
return -EINVAL;
|
|
|
|
/* Check if phase-0 is present in first valid window? */
|
|
if (!ranges[0][0]) {
|
|
phase_0_found = true;
|
|
phase_0_raw_index = 0;
|
|
/* Check if cycle exist between 2 valid windows */
|
|
for (cnt = 1; cnt <= row_index; cnt++) {
|
|
if (phases_per_row[cnt]) {
|
|
for (i = 0; i < phases_per_row[cnt]; i++) {
|
|
if (ranges[cnt][i] == 15) {
|
|
phase_15_found = true;
|
|
phase_15_raw_index = cnt;
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
}
|
|
}
|
|
|
|
/* If 2 valid windows form cycle then merge them as single window */
|
|
if (phase_0_found && phase_15_found) {
|
|
/* number of phases in raw where phase 0 is present */
|
|
u8 phases_0 = phases_per_row[phase_0_raw_index];
|
|
/* number of phases in raw where phase 15 is present */
|
|
u8 phases_15 = phases_per_row[phase_15_raw_index];
|
|
|
|
if (phases_0 + phases_15 >= MAX_PHASES)
|
|
/*
|
|
* If there are more than 1 phase windows then total
|
|
* number of phases in both the windows should not be
|
|
* more than or equal to MAX_PHASES.
|
|
*/
|
|
return -EINVAL;
|
|
|
|
/* Merge 2 cyclic windows */
|
|
i = phases_15;
|
|
for (cnt = 0; cnt < phases_0; cnt++) {
|
|
ranges[phase_15_raw_index][i] =
|
|
ranges[phase_0_raw_index][cnt];
|
|
if (++i >= MAX_PHASES)
|
|
break;
|
|
}
|
|
|
|
phases_per_row[phase_0_raw_index] = 0;
|
|
phases_per_row[phase_15_raw_index] = phases_15 + phases_0;
|
|
}
|
|
|
|
for (cnt = 0; cnt <= row_index; cnt++) {
|
|
if (phases_per_row[cnt] > curr_max) {
|
|
curr_max = phases_per_row[cnt];
|
|
selected_row_index = cnt;
|
|
}
|
|
}
|
|
|
|
i = (curr_max * 3) / 4;
|
|
if (i)
|
|
i--;
|
|
|
|
ret = ranges[selected_row_index][i];
|
|
|
|
if (ret >= MAX_PHASES) {
|
|
ret = -EINVAL;
|
|
dev_err(mmc_dev(mmc), "%s: Invalid phase selected=%d\n",
|
|
mmc_hostname(mmc), ret);
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static inline void msm_cm_dll_set_freq(struct sdhci_host *host)
|
|
{
|
|
u32 mclk_freq = 0, config;
|
|
|
|
/* Program the MCLK value to MCLK_FREQ bit field */
|
|
if (host->clock <= 112000000)
|
|
mclk_freq = 0;
|
|
else if (host->clock <= 125000000)
|
|
mclk_freq = 1;
|
|
else if (host->clock <= 137000000)
|
|
mclk_freq = 2;
|
|
else if (host->clock <= 150000000)
|
|
mclk_freq = 3;
|
|
else if (host->clock <= 162000000)
|
|
mclk_freq = 4;
|
|
else if (host->clock <= 175000000)
|
|
mclk_freq = 5;
|
|
else if (host->clock <= 187000000)
|
|
mclk_freq = 6;
|
|
else if (host->clock <= 200000000)
|
|
mclk_freq = 7;
|
|
|
|
config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
|
|
config &= ~CMUX_SHIFT_PHASE_MASK;
|
|
config |= mclk_freq << CMUX_SHIFT_PHASE_SHIFT;
|
|
writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
|
|
}
|
|
|
|
/* Initialize the DLL (Programmable Delay Line) */
|
|
static int msm_init_cm_dll(struct sdhci_host *host)
|
|
{
|
|
struct mmc_host *mmc = host->mmc;
|
|
int wait_cnt = 50;
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&host->lock, flags);
|
|
|
|
/*
|
|
* Make sure that clock is always enabled when DLL
|
|
* tuning is in progress. Keeping PWRSAVE ON may
|
|
* turn off the clock.
|
|
*/
|
|
writel_relaxed((readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC)
|
|
& ~CORE_CLK_PWRSAVE), host->ioaddr + CORE_VENDOR_SPEC);
|
|
|
|
/* Write 1 to DLL_RST bit of DLL_CONFIG register */
|
|
writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
|
|
| CORE_DLL_RST), host->ioaddr + CORE_DLL_CONFIG);
|
|
|
|
/* Write 1 to DLL_PDN bit of DLL_CONFIG register */
|
|
writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
|
|
| CORE_DLL_PDN), host->ioaddr + CORE_DLL_CONFIG);
|
|
msm_cm_dll_set_freq(host);
|
|
|
|
/* Write 0 to DLL_RST bit of DLL_CONFIG register */
|
|
writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
|
|
& ~CORE_DLL_RST), host->ioaddr + CORE_DLL_CONFIG);
|
|
|
|
/* Write 0 to DLL_PDN bit of DLL_CONFIG register */
|
|
writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
|
|
& ~CORE_DLL_PDN), host->ioaddr + CORE_DLL_CONFIG);
|
|
|
|
/* Set DLL_EN bit to 1. */
|
|
writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
|
|
| CORE_DLL_EN), host->ioaddr + CORE_DLL_CONFIG);
|
|
|
|
/* Set CK_OUT_EN bit to 1. */
|
|
writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
|
|
| CORE_CK_OUT_EN), host->ioaddr + CORE_DLL_CONFIG);
|
|
|
|
/* Wait until DLL_LOCK bit of DLL_STATUS register becomes '1' */
|
|
while (!(readl_relaxed(host->ioaddr + CORE_DLL_STATUS) &
|
|
CORE_DLL_LOCK)) {
|
|
/* max. wait for 50us sec for LOCK bit to be set */
|
|
if (--wait_cnt == 0) {
|
|
dev_err(mmc_dev(mmc), "%s: DLL failed to LOCK\n",
|
|
mmc_hostname(mmc));
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
|
return -ETIMEDOUT;
|
|
}
|
|
udelay(1);
|
|
}
|
|
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
|
return 0;
|
|
}
|
|
|
|
static int sdhci_msm_execute_tuning(struct sdhci_host *host, u32 opcode)
|
|
{
|
|
int tuning_seq_cnt = 3;
|
|
u8 phase, tuned_phases[16], tuned_phase_cnt = 0;
|
|
int rc;
|
|
struct mmc_host *mmc = host->mmc;
|
|
struct mmc_ios ios = host->mmc->ios;
|
|
|
|
/*
|
|
* Tuning is required for SDR104, HS200 and HS400 cards and
|
|
* if clock frequency is greater than 100MHz in these modes.
|
|
*/
|
|
if (host->clock <= 100 * 1000 * 1000 ||
|
|
!((ios.timing == MMC_TIMING_MMC_HS200) ||
|
|
(ios.timing == MMC_TIMING_UHS_SDR104)))
|
|
return 0;
|
|
|
|
retry:
|
|
/* First of all reset the tuning block */
|
|
rc = msm_init_cm_dll(host);
|
|
if (rc)
|
|
return rc;
|
|
|
|
phase = 0;
|
|
do {
|
|
/* Set the phase in delay line hw block */
|
|
rc = msm_config_cm_dll_phase(host, phase);
|
|
if (rc)
|
|
return rc;
|
|
|
|
rc = mmc_send_tuning(mmc, opcode, NULL);
|
|
if (!rc) {
|
|
/* Tuning is successful at this tuning point */
|
|
tuned_phases[tuned_phase_cnt++] = phase;
|
|
dev_dbg(mmc_dev(mmc), "%s: Found good phase = %d\n",
|
|
mmc_hostname(mmc), phase);
|
|
}
|
|
} while (++phase < ARRAY_SIZE(tuned_phases));
|
|
|
|
if (tuned_phase_cnt) {
|
|
rc = msm_find_most_appropriate_phase(host, tuned_phases,
|
|
tuned_phase_cnt);
|
|
if (rc < 0)
|
|
return rc;
|
|
else
|
|
phase = rc;
|
|
|
|
/*
|
|
* Finally set the selected phase in delay
|
|
* line hw block.
|
|
*/
|
|
rc = msm_config_cm_dll_phase(host, phase);
|
|
if (rc)
|
|
return rc;
|
|
dev_dbg(mmc_dev(mmc), "%s: Setting the tuning phase to %d\n",
|
|
mmc_hostname(mmc), phase);
|
|
} else {
|
|
if (--tuning_seq_cnt)
|
|
goto retry;
|
|
/* Tuning failed */
|
|
dev_dbg(mmc_dev(mmc), "%s: No tuning point found\n",
|
|
mmc_hostname(mmc));
|
|
rc = -EIO;
|
|
}
|
|
|
|
return rc;
|
|
}
|
|
|
|
static const struct of_device_id sdhci_msm_dt_match[] = {
|
|
{ .compatible = "qcom,sdhci-msm-v4" },
|
|
{},
|
|
};
|
|
|
|
MODULE_DEVICE_TABLE(of, sdhci_msm_dt_match);
|
|
|
|
static struct sdhci_ops sdhci_msm_ops = {
|
|
.platform_execute_tuning = sdhci_msm_execute_tuning,
|
|
.reset = sdhci_reset,
|
|
.set_clock = sdhci_set_clock,
|
|
.set_bus_width = sdhci_set_bus_width,
|
|
.set_uhs_signaling = sdhci_set_uhs_signaling,
|
|
};
|
|
|
|
static int sdhci_msm_probe(struct platform_device *pdev)
|
|
{
|
|
struct sdhci_host *host;
|
|
struct sdhci_pltfm_host *pltfm_host;
|
|
struct sdhci_msm_host *msm_host;
|
|
struct resource *core_memres;
|
|
int ret;
|
|
u16 host_version, core_minor;
|
|
u32 core_version, caps;
|
|
u8 core_major;
|
|
|
|
msm_host = devm_kzalloc(&pdev->dev, sizeof(*msm_host), GFP_KERNEL);
|
|
if (!msm_host)
|
|
return -ENOMEM;
|
|
|
|
msm_host->sdhci_msm_pdata.ops = &sdhci_msm_ops;
|
|
host = sdhci_pltfm_init(pdev, &msm_host->sdhci_msm_pdata, 0);
|
|
if (IS_ERR(host))
|
|
return PTR_ERR(host);
|
|
|
|
pltfm_host = sdhci_priv(host);
|
|
pltfm_host->priv = msm_host;
|
|
msm_host->mmc = host->mmc;
|
|
msm_host->pdev = pdev;
|
|
|
|
ret = mmc_of_parse(host->mmc);
|
|
if (ret)
|
|
goto pltfm_free;
|
|
|
|
sdhci_get_of_property(pdev);
|
|
|
|
/* Setup SDCC bus voter clock. */
|
|
msm_host->bus_clk = devm_clk_get(&pdev->dev, "bus");
|
|
if (!IS_ERR(msm_host->bus_clk)) {
|
|
/* Vote for max. clk rate for max. performance */
|
|
ret = clk_set_rate(msm_host->bus_clk, INT_MAX);
|
|
if (ret)
|
|
goto pltfm_free;
|
|
ret = clk_prepare_enable(msm_host->bus_clk);
|
|
if (ret)
|
|
goto pltfm_free;
|
|
}
|
|
|
|
/* Setup main peripheral bus clock */
|
|
msm_host->pclk = devm_clk_get(&pdev->dev, "iface");
|
|
if (IS_ERR(msm_host->pclk)) {
|
|
ret = PTR_ERR(msm_host->pclk);
|
|
dev_err(&pdev->dev, "Perpheral clk setup failed (%d)\n", ret);
|
|
goto bus_clk_disable;
|
|
}
|
|
|
|
ret = clk_prepare_enable(msm_host->pclk);
|
|
if (ret)
|
|
goto bus_clk_disable;
|
|
|
|
/* Setup SDC MMC clock */
|
|
msm_host->clk = devm_clk_get(&pdev->dev, "core");
|
|
if (IS_ERR(msm_host->clk)) {
|
|
ret = PTR_ERR(msm_host->clk);
|
|
dev_err(&pdev->dev, "SDC MMC clk setup failed (%d)\n", ret);
|
|
goto pclk_disable;
|
|
}
|
|
|
|
/* Vote for maximum clock rate for maximum performance */
|
|
ret = clk_set_rate(msm_host->clk, INT_MAX);
|
|
if (ret)
|
|
dev_warn(&pdev->dev, "core clock boost failed\n");
|
|
|
|
ret = clk_prepare_enable(msm_host->clk);
|
|
if (ret)
|
|
goto pclk_disable;
|
|
|
|
core_memres = platform_get_resource(pdev, IORESOURCE_MEM, 1);
|
|
msm_host->core_mem = devm_ioremap_resource(&pdev->dev, core_memres);
|
|
|
|
if (IS_ERR(msm_host->core_mem)) {
|
|
dev_err(&pdev->dev, "Failed to remap registers\n");
|
|
ret = PTR_ERR(msm_host->core_mem);
|
|
goto clk_disable;
|
|
}
|
|
|
|
/* Reset the core and Enable SDHC mode */
|
|
writel_relaxed(readl_relaxed(msm_host->core_mem + CORE_POWER) |
|
|
CORE_SW_RST, msm_host->core_mem + CORE_POWER);
|
|
|
|
/* SW reset can take upto 10HCLK + 15MCLK cycles. (min 40us) */
|
|
usleep_range(1000, 5000);
|
|
if (readl(msm_host->core_mem + CORE_POWER) & CORE_SW_RST) {
|
|
dev_err(&pdev->dev, "Stuck in reset\n");
|
|
ret = -ETIMEDOUT;
|
|
goto clk_disable;
|
|
}
|
|
|
|
/* Set HC_MODE_EN bit in HC_MODE register */
|
|
writel_relaxed(HC_MODE_EN, (msm_host->core_mem + CORE_HC_MODE));
|
|
|
|
host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION;
|
|
host->quirks |= SDHCI_QUIRK_SINGLE_POWER_WRITE;
|
|
|
|
host_version = readw_relaxed((host->ioaddr + SDHCI_HOST_VERSION));
|
|
dev_dbg(&pdev->dev, "Host Version: 0x%x Vendor Version 0x%x\n",
|
|
host_version, ((host_version & SDHCI_VENDOR_VER_MASK) >>
|
|
SDHCI_VENDOR_VER_SHIFT));
|
|
|
|
core_version = readl_relaxed(msm_host->core_mem + CORE_MCI_VERSION);
|
|
core_major = (core_version & CORE_VERSION_MAJOR_MASK) >>
|
|
CORE_VERSION_MAJOR_SHIFT;
|
|
core_minor = core_version & CORE_VERSION_MINOR_MASK;
|
|
dev_dbg(&pdev->dev, "MCI Version: 0x%08x, major: 0x%04x, minor: 0x%02x\n",
|
|
core_version, core_major, core_minor);
|
|
|
|
/*
|
|
* Support for some capabilities is not advertised by newer
|
|
* controller versions and must be explicitly enabled.
|
|
*/
|
|
if (core_major >= 1 && core_minor != 0x11 && core_minor != 0x12) {
|
|
caps = readl_relaxed(host->ioaddr + SDHCI_CAPABILITIES);
|
|
caps |= SDHCI_CAN_VDD_300 | SDHCI_CAN_DO_8BIT;
|
|
writel_relaxed(caps, host->ioaddr +
|
|
CORE_VENDOR_SPEC_CAPABILITIES0);
|
|
}
|
|
|
|
ret = sdhci_add_host(host);
|
|
if (ret)
|
|
goto clk_disable;
|
|
|
|
return 0;
|
|
|
|
clk_disable:
|
|
clk_disable_unprepare(msm_host->clk);
|
|
pclk_disable:
|
|
clk_disable_unprepare(msm_host->pclk);
|
|
bus_clk_disable:
|
|
if (!IS_ERR(msm_host->bus_clk))
|
|
clk_disable_unprepare(msm_host->bus_clk);
|
|
pltfm_free:
|
|
sdhci_pltfm_free(pdev);
|
|
return ret;
|
|
}
|
|
|
|
static int sdhci_msm_remove(struct platform_device *pdev)
|
|
{
|
|
struct sdhci_host *host = platform_get_drvdata(pdev);
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct sdhci_msm_host *msm_host = pltfm_host->priv;
|
|
int dead = (readl_relaxed(host->ioaddr + SDHCI_INT_STATUS) ==
|
|
0xffffffff);
|
|
|
|
sdhci_remove_host(host, dead);
|
|
sdhci_pltfm_free(pdev);
|
|
clk_disable_unprepare(msm_host->clk);
|
|
clk_disable_unprepare(msm_host->pclk);
|
|
if (!IS_ERR(msm_host->bus_clk))
|
|
clk_disable_unprepare(msm_host->bus_clk);
|
|
return 0;
|
|
}
|
|
|
|
static struct platform_driver sdhci_msm_driver = {
|
|
.probe = sdhci_msm_probe,
|
|
.remove = sdhci_msm_remove,
|
|
.driver = {
|
|
.name = "sdhci_msm",
|
|
.of_match_table = sdhci_msm_dt_match,
|
|
},
|
|
};
|
|
|
|
module_platform_driver(sdhci_msm_driver);
|
|
|
|
MODULE_DESCRIPTION("Qualcomm Secure Digital Host Controller Interface driver");
|
|
MODULE_LICENSE("GPL v2");
|