The chip is similar to IT8732E, but supports only three fans
and pwm outputs instead of four (the driver currently does not
support the 4th fan and pwm output of IT8732E).
Note that the chip ID is 0x8733, not 0x8792 as one would expect.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In IT8620E, after setting pwm control to manual, it was observed that
pwm values for fan 4..6 have reversed results (writing 0 results in fans
running at full speed, writing 255 results in fans turned off).
With the new PWM control, pwm polarity for pwm control 4..6 is specified
in its pwm control registers. Those registers are overwritten when setting
the pwm mode or the temperature mapping. Do not touch bit 2..6 of pwm
control registers on register writes to fix the problem.
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwm4 is enabled if bit 2 of GPIO control register 4 is disabled,
not when it is enabled. Since the check is for the skip condition,
it is reversed. This applies to both IT8620 and IT8628.
Fixes: 36c4d98a78 ("hwmon: (it87) Add support for all pwm channels ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If sensor attributes were never read, the pwm control data has not been
initiialized, which can cause wrong driver behavior. Ensure that cached
data is current before acting on it.
Cc: stable@vger.kernel.org # 4.4+
Reported-by: Kevin Folz <kfolz@evertz.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Configuration registers on ITE8622 are different to 8620 and 8628 and
require special handling. Also, the chip supports up to 5 pwm controls.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8622E is similar to IT8620E, but only supports five pwm controls and
five fan tachometers.
Originally-from: Kevin Folz <kfolz@evertz.com>.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On IT8622E and IT8628E, VIN3 is expected to be connected to +5V.
Add feature flag and reflect in input label.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If btrfs_decompress_buf2page() is handed a bio with its page in the
middle of the working buffer, then we adjust the offset into the working
buffer. After we copy into the bio, we advance the iterator by the
number of bytes we copied. Then, we have some logic to handle the case
of discontiguous pages and adjust the offset into the working buffer
again. However, if we didn't advance the bio to a new page, we may enter
this case in error, essentially repeating the adjustment that we already
made when we entered the function. The end result is bogus data in the
bio.
Previously, we only checked for this case when we advanced to a new
page, but the conversion to bio iterators changed that. This restores
the old, correct behavior.
A case I saw when testing with zlib was:
buf_start = 42769
total_out = 46865
working_bytes = total_out - buf_start = 4096
start_byte = 45056
The condition (total_out > start_byte && buf_start < start_byte) is
true, so we adjust the offset:
buf_offset = start_byte - buf_start = 2287
working_bytes -= buf_offset = 1809
current_buf_start = buf_start = 42769
Then, we copy
bytes = min(bvec.bv_len, PAGE_SIZE - buf_offset, working_bytes) = 1809
buf_offset += bytes = 4096
working_bytes -= bytes = 0
current_buf_start += bytes = 44578
After bio_advance(), we are still in the same page, so start_byte is the
same. Then, we check (total_out > start_byte && current_buf_start < start_byte),
which is true! So, we adjust the values again:
buf_offset = start_byte - buf_start = 2287
working_bytes = total_out - start_byte = 1809
current_buf_start = buf_start + buf_offset = 45056
But note that working_bytes was already zero before this, so we should
have stopped copying.
Fixes: 974b1adc3b ("btrfs: use bio iterators for the decompression handlers")
Reported-by: Pat Erley <pat-lkml@erley.org>
Reviewed-by: Chris Mason <clm@fb.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Tested-by: Liu Bo <bo.li.liu@oracle.com>
Pull networking fixes from David Miller:
1) If the timing is wrong we can indefinitely stop generating new ipv6
temporary addresses, from Marcus Huewe.
2) Don't double free per-cpu stats in ipv6 SIT tunnel driver, from Cong
Wang.
3) Put protections in place so that AF_PACKET is not able to submit
packets which don't even have a link level header to drivers. From
Willem de Bruijn.
4) Fix memory leaks in ipv4 and ipv6 multicast code, from Hangbin Liu.
5) Don't use udp_ioctl() in l2tp code, UDP version expects a UDP socket
and that doesn't go over very well when it is passed an L2TP one.
Fix from Eric Dumazet.
6) Don't crash on NULL pointer in phy_attach_direct(), from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
l2tp: do not use udp_ioctl()
xen-netfront: Delete rx_refill_timer in xennet_disconnect_backend()
NET: mkiss: Fix panic
net: hns: Fix the device being used for dma mapping during TX
net: phy: Initialize mdio clock at probe function
igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()
xen-netfront: Improve error handling during initialization
sierra_net: Skip validating irrelevant fields for IDLE LSIs
sierra_net: Add support for IPv6 and Dual-Stack Link Sense Indications
kcm: fix 0-length case for kcm_sendmsg()
xen-netfront: Rework the fix for Rx stall during OOM and network stress
net: phy: Fix PHY module checks and NULL deref in phy_attach_direct()
net: thunderx: Fix PHY autoneg for SGMII QLM mode
net: dsa: Do not destroy invalid network devices
ping: fix a null pointer dereference
packet: round up linear to header len
net: introduce device min_header_len
sit: fix a double free on error path
lwtunnel: valid encap attr check should return 0 when lwtunnel is disabled
ipv6: addrconf: fix generation of new temporary addresses
- Two security related issues in the rxe driver
- One compile issue in the RDMA uapi header
-----BEGIN PGP SIGNATURE-----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=zGBQ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Third round of -rc fixes for 4.10 kernel:
- two security related issues in the rxe driver
- one compile issue in the RDMA uapi header"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
RDMA: Don't reference kernel private header from UAPI header
IB/rxe: Fix mem_check_range integer overflow
IB/rxe: Fix resid update
Pull i2c bugfixes from Wolfram Sang:
"Two bugfixes (proper IO mapping and use of mutex) for a driver feature
we introduced in this cycle"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: piix4: Request the SMBUS semaphore inside the mutex
i2c: piix4: Fix request_region size
here is the last-minute fixes for 4.10 final (or -rc8): two fixes for
races in ALSA sequencer queue spotted by syzkaller, a revert for a
regression of LINE6 driver (since 4.9), and a trivial new codec ID
addition for Nvidia HDMI.
-----BEGIN PGP SIGNATURE-----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=CAxe
-----END PGP SIGNATURE-----
Merge tag 'sound-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are some last-minute fixes: two fixes for races in ALSA sequencer
queue spotted by syzkaller, a revert for a regression of LINE6 driver
(since 4.9), and a trivial new codec ID addition for Nvidia HDMI"
* tag 'sound-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - adding a new NV HDMI/DP codec ID in the driver
ALSA: seq: Fix race at creating a queue
Revert "ALSA: line6: Only determine control port properties if needed"
ALSA: seq: Don't handle loop timeout at snd_seq_pool_done()
fixable, but at least one of the fixes is a little ugly. The original
bug has always been there, so we can wait another week or two to get
this right.
-----BEGIN PGP SIGNATURE-----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=1kRc
-----END PGP SIGNATURE-----
Merge tag 'nfsd-4.10-3' of git://linux-nfs.org/~bfields/linux
Pull nfsd revert from Bruce Fields:
"This patch turned out to have a couple problems. The problems are
fixable, but at least one of the fixes is a little ugly. The original
bug has always been there, so we can wait another week or two to get
this right"
* tag 'nfsd-4.10-3' of git://linux-nfs.org/~bfields/linux:
nfsd: Revert "nfsd: special case truncates some more"
Four fixes from Ben:
- Userspace was semi-randomly segfaulting on radix due to us incorrectly
handling a fault triggered by autonuma, caused by a patch we merged earlier
in v4.10 to prevent the kernel executing userspace.
- We weren't marking host IPIs properly for KVM in the OPAL ICP backend.
- The ERAT flushing on radix was missing an isync and was incorrectly marked
as DD1 only.
- The powernv CPU hotplug code was missing a wakeup type and failing to flush
the interrupt correctly when using OPAL ICP.
Thanks to:
Benjamin Herrenschmidt.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yLmR
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes friom Michael Ellerman:
"Apologies for the late pull request, but Ben has been busy finding bugs.
- Userspace was semi-randomly segfaulting on radix due to us
incorrectly handling a fault triggered by autonuma, caused by a
patch we merged earlier in v4.10 to prevent the kernel executing
userspace.
- We weren't marking host IPIs properly for KVM in the OPAL ICP
backend.
- The ERAT flushing on radix was missing an isync and was incorrectly
marked as DD1 only.
- The powernv CPU hotplug code was missing a wakeup type and failing
to flush the interrupt correctly when using OPAL ICP
Thanks to Benjamin Herrenschmidt"
* tag 'powerpc-4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Properly set "host-ipi" on IPIs
powerpc/powernv: Fix CPU hotplug to handle waking on HVI
powerpc/mm/radix: Update ERAT flushes when invalidating TLB
powerpc/mm: Fix spurrious segfaults on radix with autonuma
udp_ioctl(), as its name suggests, is used by UDP protocols,
but is also used by L2TP :(
L2TP should use its own handler, because it really does not
look the same.
SIOCINQ for instance should not assume UDP checksum or headers.
Thanks to Andrey and syzkaller team for providing the report
and a nice reproducer.
While crashes only happen on recent kernels (after commit
7c13f97ffd ("udp: do fwd memory scheduling on dequeue")), this
probably needs to be backported to older kernels.
Fixes: 7c13f97ffd ("udp: do fwd memory scheduling on dequeue")
Fixes: 8558467201 ("udp: Fix udp_poll() and ioctl()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If the irq_desc being output does not have a domain associated the
information following the 'name' is not aligned correctly.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Link: http://lkml.kernel.org/r/20170210165416.5629-1-hsweeten@visionengravers.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
rx_refill_timer should be deleted as soon as we disconnect from the
backend since otherwise it is possible for the timer to go off before
we get to xennet_destroy_queues(). If this happens we may dereference
queue->rx.sring which is set to NULL in xennet_disconnect_backend().
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a USB-to-serial adapter is unplugged, the driver re-initializes, with
dev->hard_header_len and dev->addr_len set to zero, instead of the correct
values. If then a packet is sent through the half-dead interface, the
kernel will panic due to running out of headroom in the skb when pushing
for the AX.25 headers resulting in this panic:
[<c0595468>] (skb_panic) from [<c0401f70>] (skb_push+0x4c/0x50)
[<c0401f70>] (skb_push) from [<bf0bdad4>] (ax25_hard_header+0x34/0xf4 [ax25])
[<bf0bdad4>] (ax25_hard_header [ax25]) from [<bf0d05d4>] (ax_header+0x38/0x40 [mkiss])
[<bf0d05d4>] (ax_header [mkiss]) from [<c041b584>] (neigh_compat_output+0x8c/0xd8)
[<c041b584>] (neigh_compat_output) from [<c043e7a8>] (ip_finish_output+0x2a0/0x914)
[<c043e7a8>] (ip_finish_output) from [<c043f948>] (ip_output+0xd8/0xf0)
[<c043f948>] (ip_output) from [<c043f04c>] (ip_local_out_sk+0x44/0x48)
This patch makes mkiss behave like the 6pack driver. 6pack does not
panic. In 6pack.c sp_setup() (same function name here) the values for
dev->hard_header_len and dev->addr_len are set to the same values as in
my mkiss patch.
[ralf@linux-mips.org: Massages original submission to conform to the usual
standards for patch submissions.]
Signed-off-by: Thomas Osterried <thomas@osterried.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the device being used to DMA map skb->data.
Erroneous device assignment causes the crash when SMMU is enabled.
This happens during TX since buffer gets DMA mapped with device
correspondign to net_device and gets unmapped using the device
related to DSAF.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This can be used to easily identify a specific chip on a system with
multiple chips.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This can be used to easily identify a specific chip on a system with
multiple chips.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
-----BEGIN PGP SIGNATURE-----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=/fPM
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.11-v2' of git://github.com/spi-nor/linux
From Cyrille:
"""
This pull request contains the following notable changes:
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
"""
physmap_of sort of depends on the gemini and versatile modules (when
they're enabled), but this isn't expressed in Kconfig. Let's just merge
the modules all together, when enabled. Then we can avoid exporting a
few symbols, and the versatile and gemini code can now be modular again
(the below commit accidentally made them built-in only).
Resolves errors like this:
ERROR: "of_flash_probe_versatile" [drivers/mtd/maps/physmap_of.ko] undefined!
ERROR: "of_flash_probe_gemini" [drivers/mtd/maps/physmap_of.ko] undefined!
Fixes: 56ff337ea4 ("mtd: physmap_of: add a hook for Gemini flash probing")
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 5d70499218 ("vfio/type1: Allow transparent MSI IOVA allocation")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
And also move its remaining functionality to
iommu_device_register() and 'struct iommu_device'.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Register Exynos IOMMUs to the IOMMU core and make them
visible in sysfs. This patch does not add the links between
IOMMUs and translated devices yet.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
- keystone: Fix scheduling while atomic for realtime
- mxs: Enable SKIP_SET_WAKE and MASK_ON_SUSPEND
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJYnb9bAAoJECyKW7NnfWw8UAMP/3A4RqtFwZafbuNyDBbtqUfc
JMvKKeDFIYA6uMPiG5c63OxZr5C9BdOocIr1+Wcnv+oz/VIY9fBFsLSZF0sbw+9W
B90pcquJuDt591OBrwF5Y0Putb/R0epTxhsRAHiOzLYXBqU8s73V2MSo+H+lD6nA
y4it/goX9jxN2njJSDGxegyvaesKP83d1MDTf9asH2jXhP1qKqCRfyc9BUrgRMDQ
fIxBLD6TakdLK3Wrt1h3iScToUXwqTDbBng6v67Q8Ldk6j0yCCS8dPIllUMEkoYx
1Fac/qLXymA/xhDB6aP/d4zL1/jIQEwjZc+PicbOiAVPLdcAJUseVXfqboDtFbu+
pDZQrq2pxhUzJ1p2fX0Kkfg1VZv1BMqBk9mXBC8p2SG0w/SLWh/JK6o77T1fF8NQ
WTzou+D+TeCJLK1fWdZhcQAd8SVxwfI02D9ezAO/AqxPNmOIf7uGU2iSoPLi4C53
Pa/3Sg1KO1z8O4ROBPlUwd6p+bqGkSt0o425FRYJrrcD3R+AI+g9EWqQRrOlbf0L
l6netbUrgrnPs14ZPg4oObps03QHz3nEcw6yZkYpyfBxqPA96m5zff7NzI52pjmv
uFFbg84ZgSqhC2i2Eui7YlnKJIdwBknBToZXnfbw39omc9v835Agsi4pCqXM3AEY
RqSaWgr4dB1SrICLseQW
=zi4v
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-4.10' of git://git.infradead.org/users/jcooper/linux into irq/urgent
Pull irqchip fixes for v4.10 from Jason Cooper
- keystone: Fix scheduling while atomic for realtime
- mxs: Enable SKIP_SET_WAKE and MASK_ON_SUSPEND
Checking for ret < 0 is redundant because a previous check on ret
being non-zero already handles the ret < 0 case. Remove the redundant
code. Found by CoverityScan, CID#1398863, CID#1398864
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Add "mediatek,mt2701-nor" for nor flash node's compatible.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
There are some read modes for flash, such as NORMAL, FAST,
QUAD, DDR QUAD. These modes will use the identical lut table base
So rename SEQID_QUAD_READ to SEQID_READ.
Signed-off-by: Yunhui Cui <B56489@freescale.com>
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
We can get the read/write/erase opcode from the spi nor framework
directly. This patch uses the information stored in the SPI-NOR to
remove the hardcode in the fsl_qspi_init_lut().
Signed-off-by: Yunhui Cui <B56489@freescale.com>
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The page calculation under spi_nor_s3an_addr_convert() was wrong. On
Default Address Mode we need to perform a divide by page_size.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The first argument of ioread32_rep() and ioread8_rep is not
const. Change aspeed_smc_read_from_ahb() prototype to fix compile
warning :
drivers/mtd/spi-nor/aspeed-smc.c: In function 'aspeed_smc_read_from_ahb':
drivers/mtd/spi-nor/aspeed-smc.c:212:16: warning: passing argument 1 of 'ioread32_rep' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
ioread32_rep(src, buf, len >> 2);
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The MR25 family doesn't support JEDEC, so they need explicit mentioning
in the list of supported spi IDs. This makes it possible to add these
using for example:
compatible = "everspin,mr25h40";
There was already an entry for mr25h256. Move that one out of the "keep
for compatibility" section and put in a new group for Everspin MRAMs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
-----BEGIN PGP SIGNATURE-----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=1Yep
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-mtd-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
From Lee Jones:
"""
Immutable branch between MFD and MTD due for the v4.11 merge window
"""
This chip has write protection enabled on power-up,
so this flag is necessary to support write operations.
Signed-off-by: Victor Shyba <victor1984@riseup.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This patch provides an alternative mean to support memory above 16MiB
(128Mib) by replacing 3byte address op codes by their associated 4byte
address versions.
Using the dedicated 4byte address op codes doesn't change the internal
state of the SPI NOR memory as opposed to using other means such as
updating a Base Address Register (BAR) and sending command to enter/leave
the 4byte mode.
Hence when a CPU reset occurs, early bootloaders don't need to be aware
of BAR value or 4byte mode being enabled: they can still access the first
16MiB of the SPI NOR memory using the regular 3byte address op codes.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Tested-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This patch renames the SPINOR_OP_* macros of the 4-byte address
instruction set so the new names all share a common pattern: the 4-byte
address name is built from the 3-byte address name appending the "_4B"
suffix.
The patch also introduces new op codes to support other SPI protocols such
as SPI 1-4-4 and SPI 1-2-2.
This is a transitional patch and will help a later patch of spi-nor.c
to automate the translation from the 3-byte address op codes into their
4-byte address version.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Consider a message size limit when calculating the maximum amount
of data that can be read.
The message size limit has been introduced with 4.9, so cc it
to stable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This driver adds mtd support for the Aspeed AST2400 SoC static memory
controllers:
* New Static Memory Controller (referred as FMC)
. BMC firmware
. AST2500 compatible register set
. 5 chip select pins (CE0 ∼ CE4)
. supports NOR flash, NAND flash and SPI flash memory.
* SPI Flash Controller (SPI)
. host Firmware
. slightly different register set, between AST2500 and the legacy
controller
. supports SPI flash memory
. 1 chip select pin (CE0)
The legacy static memory controller (referred as SMC) is not
supported, as well as types other than SPI.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This driver adds mtd support for the Aspeed AST2500 SoC static memory
controllers :
* Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the
driver
* SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. supports SPI type flash memory
Each controller has a memory range on which it maps its flash module
slaves. Each slave is assigned a memory window for its mapping that
can be changed at bootime with the Segment Address Register.
Each SPI flash slave can then be accessed in two modes: Command and
User. When in User mode, accesses to the memory segment of the slaves
are translated in SPI transfers. When in Command mode, the HW
generates the SPI commands automatically and the memory segment is
accessed as if doing a MMIO.
Currently, only the User mode is supported. Command mode needs a
little more work to check that the memory window on the AHB bus fits
the module size.
Based on previous work from Milton D. Miller II <miltonm@us.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This patch removes the WARN_ONCE() test in spi_nor_write().
This macro triggers the display of a warning message almost every time we
use a UBI file-system because a write operation is performed at offset 64,
which is in the middle of the SPI NOR memory page. This is a valid
operation for ubifs.
Hence this warning is pretty annoying and useless so we just remove it.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Suggested-by: Richard Weinberger <richard@nod.at>
Suggested-by: Andras Szemzo <szemzo.andras@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The patch checks whether the Quad Enable bit is already set in the Status
Register. If so, the function exits immediately with a successful return
code.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
