Implement proper two stage watermark programming for g4x. As with
other pre-SKL platforms, the watermark registers aren't double
buffered on g4x. Hence we must sequence the watermark update
carefully around plane updates.
The code is quite heavily modelled on the VLV/CHV code, with some
fairly significant differences due to the different hardware
architecture:
* g4x doesn't use inverted watermark values
* CxSR actually affects the watermarks since it controls memory self
refresh in addition to the max FIFO mode
* A further HPLL SR mode is possible with higher memory wakeup
latency
* g4x has FBC2 and so it also has FBC watermarks
* max FIFO mode for primary plane only (cursor is allowed, sprite is not)
* g4x has no manual FIFO repartitioning
* some TLB miss related workarounds are needed for the watermarks
Actually the hardware is quite similar to ILK+ in many ways. The
most visible differences are in the actual watermakr register
layout. ILK revamped that part quite heavily whereas g4x is still
using the layout inherited from earlier platforms.
Note that we didn't previously enable the HPLL SR on g4x. So in order
to not introduce too many functional changes in this patch I've not
actually enabled it here either, even though the code is now fully
ready for it. We'll enable it separately later on.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-13-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The current code looks like a typo, the specification calls for setting
bits 31:24 to 0x8C, while preserving bits 23:0. Fix things accordingly.
I'm not aware of the typo causing a real problem, so the fix is only for
consistency.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494408113-379-1-git-send-email-imre.deak@intel.com
In the previous patch we've implemented hwmode tracking a la i915 for
the vblank timestamp calculations. But that was just the basic
semantics, i915 has some nice sanity checks to make sure we keep
getting this right. Move them over too.
v2:
- WARN_ON_ONCE to avoid excessive spam (Ville)
- Really only WARN on atomic drivers.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-5-daniel.vetter@ffwll.ch
We're clearing the legacy_cursor_update flag before calling
drm_atomic_helper_setup_commit() which means the helper will
wait for the flip to complete before cleaning up the framebuffers.
That's not what we want for the legacy cursor, so let's clear
the flag after setting up the commit.
Also toss in a FIXME about solving these problems in a nicer
way using the fabled vblank workers.
v2: Also unsync with legacy page flips
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Rafael Ristovski <rafael.ristovski@gmail.com>
Fixes: a5509abda4 ("drm/i915: Fix legacy cursor vs. watermarks for ILK-BDW")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170329142123.5923-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit 8952030440)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If "crtc" is NULL, then my static checker complains that "ret" isn't
initialized on that path. It doesn't really cause a problem unless
"ret" is somehow set to -EDEADLK which is not likely.
Chris Wilson also noticed another error path where "ret" isn't set
correctly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170414195425.GA8144@mwanda
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit ea49c9acf2.
mode_config.mutex was originally added to fix WARNs in connector
functions, but now that atomic nonblocking modeset support is
included, we will likely never hold any any lock at all.
The WARN mentioned in commit bbf35e9def ("drm/i915:
Pass atomic state to intel_audio_codec_enable, v2."), so it's
safe to revert this now.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491312168-18147-1-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Maarten needs both the new connector->atomic_check hook and the
connection_mutex locking changes in the probe helpers to be able to
start merging the connector property conversion to atomic.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Last drm-misc-next pull req for 4.12
Core changes:
- fb_helper checkpatch cleanup and simplified _add_one_connector() (Thierry)
- drm_ioctl and drm_sysfs improved/gained documentation (Daniel)
- [ABI] Repurpose reserved field in drm_event_vblank for crtc_id (Ander)
- Plumb acquire ctx through legacy paths to avoid lock_all and legacy_backoff
(Daniel)
- Add connector_atomic_check to check conn constraints on modeset (Maarten)
- Add drm_of_find_panel_or_bridge to remove boilerplate in drivers (Rob)
Driver changes:
- meson moved to drm-misc (Neil)
- Added support for Amlogic GX SoCs in dw-hdmi (Neil)
- Rockchip unbind actually cleans up the things bind initializes (Jeffy)
- A couple misc fixes in virtio, dw-hdmi
NOTE: this also includes a backmerge of drm-next as well rc5 (we needed vmwgfx
as well as the new synopsys media formats)
* tag 'drm-misc-next-2017-04-07' of git://anongit.freedesktop.org/git/drm-misc: (77 commits)
Revert "drm: Don't allow interruptions when opening debugfs/crc"
drm: Only take cursor locks when the cursor plane exists
drm/vmwgfx: Fix fbdev emulation using legacy functions
drm/rockchip: Shutdown all crtcs when unbinding drm
drm/rockchip: Reorder drm bind/unbind sequence
drm/rockchip: analogix_dp: Disable clock when unbinding
drm/rockchip: vop: Unprepare clocks when unbinding
drm/rockchip: vop: Enable pm domain before vop_initial
drm/rockchip: cdn-dp: Don't unregister audio dev when unbinding
drm/rockchip: cdn-dp: Don't try to release firmware when not loaded
drm: bridge: analogix: Destroy connector & encoder when unbinding
drm: bridge: analogix: Disable clock when unbinding
drm: bridge: analogix: Unregister dp aux when unbinding
drm: bridge: analogix: Detach panel when unbinding analogix dp
drm: Don't allow interruptions when opening debugfs/crc
drm/virtio: don't leak bo on drm_gem_object_init failure
drm: bridge: dw-hdmi: fix input format/encoding from plat_data
drm: omap: use common OF graph helpers
drm: convert drivers to use drm_of_find_panel_or_bridge
drm: convert drivers to use of_graph_get_remote_node
...
Last 4.12 feature pile:
GVT updates:
- Add mdev attribute group for per-vgpu info
- Time slice based vGPU scheduling QoS support (Gao Ping)
- Initial KBL support for E3 server (Han Xu)
- other misc.
i915:
- lots and lots of small fixes and improvements all over
- refactor fw_domain code (Chris Wilson)
- improve guc code (Oscar Mateo)
- refactor cursor/sprite code, precompute more for less overhead in
the critical path (Ville)
- refactor guc/huc fw loading code a bit (Michal Wajdeczko)
* tag 'drm-intel-testing-2017-04-03' of git://anongit.freedesktop.org/git/drm-intel: (121 commits)
drm/i915: Update DRIVER_DATE to 20170403
drm/i915: Clear gt.active_requests before checking idle status
drm/i915/uc: Drop use of MISSING_CASE on trivial enums
drm/i915: make a few DDI functions static
drm/i915: Combine reset_all_global_seqno() loops into one
drm/i915: Remove redudant wait for each engine to idle from seqno wrap
drm/i915: Wait for all engines to be idle as part of i915_gem_wait_for_idle()
drm/i915: Move retire-requests into i915_gem_wait_for_idle()
drm/i915/uc: Move fw path check to fetch_uc_fw()
drm/i915/huc: Remove unused intel_huc_fini()
drm/i915/uc: Add intel_uc_fw_fini()
drm/i915/uc: Add intel_uc_fw_type_repr()
drm/i915/uc: Move intel_uc_fw_status_repr() to intel_uc.h
drivers: gpu: drm: i915L intel_lpe_audio: Fix kerneldoc comments
drm/i915: Suppress busy status for engines if wedged
drm/i915: Do request retirement before marking engines as wedged
drm/i915: Drop verbose and archaic "ring" from our internal engine names
drm/i915: Use a dummy timeline name for a signaled fence
drm/i915: Ironlake do_idle_maps w/a may be called w/o struct_mutex
drm/i915/guc: Take enable_guc_loading check out of GEM core code
...
By using the same structure for both interruptible and
uninterruptible locking in shrinker code, combined with the
information that mm.interruptible is only being written to, the
code can be greatly simplified.
Also removing the i915_gem_ prefix from the locking functions so
that nobody in their wildest dreams considers exporting them.
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1491562175-27680-1-git-send-email-joonas.lahtinen@linux.intel.com
mode_valid() called from drm_helper_probe_single_connector_modes()
may need to look at connector->state because what a valid mode is may
depend on connector properties being set. For example some HDMI modes
might be rejected when a connector property forces the connector
into DVI mode.
Some implementations of detect() already lock all state,
so we have to pass an acquire_ctx to them to prevent a deadlock.
This means changing the function signature of detect() slightly,
and passing the acquire_ctx for locking multiple crtc's.
For the callbacks, it will always be non-zero. To allow callers
not to worry about this, drm_helper_probe_detect_ctx is added
which might handle -EDEADLK for you.
Changes since v1:
- Always set ctx parameter.
Changes since v2:
- Always take connection_mutex when probing.
Changes since v3:
- Remove the ctx from intel_dp_long_pulse, and add
WARN_ON(!connection_mutex) (danvet)
- Update docs to clarify the locking situation. (danvet)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1491504920-4017-1-git-send-email-maarten.lankhorst@linux.intel.com
It just doesn't work. It probably stopped working way, way before that
(e.g. i915 grabbed random mutexes all over in modeset code at least
since gen6), but with atomic and all the ww_mutex stuff it's indeed
hopeless.
Remove ->mode_set_base_atomic from the 2 atomic drivers (i915 and
nouveau) that still had one (both had dummy implementations already
anyway), and shunt atomic drivers in the helpers debug_enter/leave
functions.
I'll leave the code in for radeon and amdgpu, but I think as soon as
amdgpu is atomic we should think about just ripping it out. Only
having it around for radeon and pre-nv50 is rather pointless. This
would also allow us to nuke all that code from fbdev.
Funny part is that _all_ kms drivers set this hook, despite that no
one else provides the required ->mode_set_base_atomic implementation.
The reason I'm jumping on this is that I want to wire up a full
acquire ctx for the benefit of atomic drivers, everywhere. And the
debug_enter/leave implementations call ->gamma_set. And there's just
no way ever we can create an acquire_ctx in the nmi context of kgdb.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-11-daniel.vetter@ffwll.ch
We do set DRIVER_ATOMIC now.
Note that the comment is outdated, the property paths switched over to
checking drm_drv_uses_atomic_modeset() a while ago. Which means this
can't even break if we revert DRIVER_ATOMIC again.
v2: Add note that this is even safer (Maarten).
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-9-daniel.vetter@ffwll.ch
With all the callers of drm_modeset_lock_crtc gone, and all the places
it was formerly used properly wiring the acquire ctx through, we can
remove this.
The only hidden context magic we still have is now the global one.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-4-daniel.vetter@ffwll.ch
We're clearing the legacy_cursor_update flag before calling
drm_atomic_helper_setup_commit() which means the helper will
wait for the flip to complete before cleaning up the framebuffers.
That's not what we want for the legacy cursor, so let's clear
the flag after setting up the commit.
Also toss in a FIXME about solving these problems in a nicer
way using the fabled vblank workers.
v2: Also unsync with legacy page flips
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Rafael Ristovski <rafael.ristovski@gmail.com>
Fixes: a5509abda4 ("drm/i915: Fix legacy cursor vs. watermarks for ILK-BDW")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170329142123.5923-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
v2 of the commit 2c77bb29d3 ("drm: simplify the locking in the GETCRTC ioctl")
accidentally introduced a unrelated change in intel_display.c, revert the
unrelated change.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 2c77bb29d3 ("drm: simplify the locking in the GETCRTC ioctl")
Reported-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/6be47261-475f-c190-af56-c136677246d9@linux.intel.com
No need to grab both plane and crtc locks at the same time, we can do
them one after the other. If userspace races it'll get what it
deserves either way.
This removes another user of drm_modeset_lock_crtc. There's only one
left.
v2: Make sure all access to primary->state is properly protected
(Harry).
Cc: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170328070145.21520-1-daniel.vetter@ffwll.ch
Just rolling it out, no code change here.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Eric Anholt <eric@anholt.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170322215058.8671-3-daniel.vetter@ffwll.ch
Several major vendor USB-C->HDMI converters, in particular the DA200,
fail to recover a 5.4 GHz 1 lane signal if the link N is greater than
0x80000.
The link M and N depend on the pixel clock and link clock ratio. With
current code link N exceeds 0x80000 only when link clock >= 540000
kHz. Except for the eDP intermediate link clocks, at least the four
least significant bits are always zero. Just one bit shift right would
be enough to bring even the DP 1.4 810000 kHz link clock under 0x80000
link N. The pixel clock for modes that require a link clock >= 540000
kHz would also have several least significant bits zero. Unless the user
provides a mode with an odd pixel clock value, we can reduce the numbers
to reach the goal, with no loss in precision.
The DP spec even mentions sources making choices that "allow for static
and relatively small Mvid and Nvid values", thus reducing the link M/N
regardless of the sink in question seems justified.
Everything here is based on the work and information gathered by Clint
Taylor <clinton.a.taylor@intel.com>. This is just an iteration to reduce
the parameters regardless of lane count, link rate, or sink.
Reference: http://patchwork.freedesktop.org/patch/msgid/1490225256-11667-1-git-send-email-clinton.a.taylor@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93578
Tested-by: Mads <mads@ab3.no>
Tested-by: PJ <foobar@pjmodos.net>
Tested-by: François Guerraz <kubrick@fgv6.net>
Tested-by: Lev Popov <leo@nabam.net>
Tested-by: Igor Krivenko <igor.s.krivenko@gmail.com>
Tested-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1490614405-23337-1-git-send-email-jani.nikula@intel.com
Geminilake platform sports a native HDMI 2.0 controller, and is
capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec
mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required,
enables it during the modeset.
V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in
driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling
in intel_enable_ddi() before enabling the port.
V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor",
so that the implementation could be close to the language of
HDMI spec.
V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling
- high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio
V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all
scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the
conditions again, just go by the crtc_state flags. This will
simplyfy the condition checks.
V6: Addressed review comments from Ville
- Do not add IS_GLK check in disable/enable function, instead add it
in compute_config, while setting state flags.
- Remove unnecessary paranthesis.
- Simplyfy handle_sink_scrambling function as suggested.
- Add readout code for scrambling status in get_ddi_config and add a
check for the same in pipe_config_compare.
V7: Addressed review comments from Ander/Ville
- No separate function for source scrambling, make it inline
- Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
- Do not add platform check while setting source scrambling
- Use pipe_config instead of crtc->config to set sink scrambling
- To readout scrambling status, Compare with SCRAMBLING_MASK
not any of its bits
- Remove platform check in intel_pipe_config_compare while checking
scrambling status
V8: Fixed mege conflict, Addressed review comments from Ander
- Remove the desciption/comment about scrambling fom the caller, move
it to the function
- Move the IS_GLK check into scrambling function
- Fix alignment
V9: Fixed review comments from Ville, Ander
- Pass the scrambling state variables as bool input to the sink_scrambling
function and let the disable call be unconditional.
- Fix alignments in function calls and debug messages.
- Add kernel doc for function intel_hdmi_handle_sink_scrambling
V10: Rebase
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com
All it does is pick the encoder and call intel_get_shared_dpll(). We
can just do this in the caller. One less indirection level during code
reading.
As another plus, now the two callers of intel_get_shared_dpll() are
{ironlake,haswell}_crtc_compute_clock().
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1490209125-20046-2-git-send-email-paulo.r.zanoni@intel.com
All the pre-SKL sprite planes compute the x/y/tile offsets in a
similar way. There are a couple of minor differences but the primary
planes have those as well. Thus i9xx_check_plane_surface()
already does what we need, so let's use it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-7-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The effective difference between i9xx_update_primary_plane()
and ironlake_update_primary_plane() is only the HSW/BDW
DSPOFFSET special case. So bring that over into
i9xx_update_primary_plane() and eliminate the duplicated code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-6-ville.syrjala@linux.intel.com
Extract the primary plane surfae offset/x/y calculations for
pre-SKL platforms into a common function, and call it during the
atomic check phase to reduce the amount of stuff we have to do
during the commit phase. SKL is already doing this.
v2: Update the comment about the rotation adjustments to
match the code better (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-5-ville.syrjala@linux.intel.com
Computing the plane control register value is branchy so moving it out
from the plane commit hook seems prudent. Let's pre-compute it during
the atomic check phase and store the result in the plane state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-4-ville.syrjala@linux.intel.com
Share the code to compute the primary plane control register value
between the i9xx and ilk codepaths as the differences are minimal.
Actually there are no differences between g4x and ilk, so the
current split doesn't really make any sense.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Pull the code to calculate the pre-SKL primary plane control register
value into separate functions. Allows us to pre-compute it in the
future.
v2: Split the pre-ilk vs. ilk+ unification to a separate patch (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
On SKL the planes are uniform so the "sprites" can use the
primary plane code perfectly fine. The only difference we
have is the color key handling, but since we never enable that
for the primary plane the same code works just fine.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170317211808.14693-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The only time we need to emit a flush inside request emission is after
an execbuffer, for which we can use the full __i915_add_request(). All
other instances want the simpler i915_add_request() without flushing, so
remove the useless helper.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170317114709.8388-1-chris@chris-wilson.co.uk
I915_RESET_IN_PROGRESS is being used for both signaling the requirement
to i915_mutex_lock_interruptible() to avoid taking the struct_mutex and
to instruct a waiter (already holding the struct_mutex) to perform the
reset. To allow for a little more coordination, split these two meaning
into a couple of distinct flags. I915_RESET_BACKOFF tells
i915_mutex_lock_interruptible() not to acquire the mutex and
I915_RESET_HANDOFF tells the waiter to call i915_reset().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170316171305.12972-1-chris@chris-wilson.co.uk
Optimize the plane register accesses a little bit by grabbing
the uncore lock manually across the entire pile of accesses and
using I915_READ_FW().
This helps keep the pipe update vblank evade critical section
below our 100 usec deadline, particularly with lockdep enabled.
And in general we want to keep that critical section as short
as possible as it's executed with interrupts disabled.
Not all plane updates currently happen from within the vblank evade
critical section, so we must use the irqsave/irqrestore variants
of the spinlock functions in the plane hooks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170309154434.29303-5-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Pull all the plane register writes closer together to avoid having
a lot of unrelated stuff in between them. This will make things more
clear once we'll grab the uncore lock around the entire bunch. Also
in the future we might even consider moving more of the register
value computation out from the plane update hooks. This should make
that easier to do.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170309154434.29303-4-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Add a big fat warning in __intel_display_resume that the old state is
invalid, and use the correct state everywhere.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489071125-917-5-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[mlankhorst: Change one occurence of conn_state to new_conn_state in
verify_connector_state, and drop old_conn_state there]
The trouble here is that looking at all connector->state in the
verifier isn't good, because that's run from the commit work, which
doesn't hold the connection_mutex. Which means we're only allowed to
look at states in our atomic update.
The simple fix for future proofing would be to switch over to
drm_for_each_connector_in_state, but that has the problem that the
verification then fails if not all connectors are in the state. And we
also need to be careful to check both old and new encoders, and not
screw things up when an encoder gets reassigned.
Note that this isn't the full fix, since we still look at
connector->state. To fix that, we need Maarten's patch series to
switch over to state pointers within drm_atomic_state, but that's a
different series.
v2: Use oldnew iterator (Maarten).
v3: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-6-daniel.vetter@ffwll.ch
This gets rid of the last users of for_each_intel_connector(), remove
that too.
At first I wasn't sure whether the 2 loops in the modeset state
checker should instead only loop over the connectors in the atomic
commit. But we never add connectors to an atomic update if they don't
(or won't have) a CRTC assigned, which means there'd be a gap in check
coverage. Hence loop over everything on those too.
v2: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-5-daniel.vetter@ffwll.ch
Drive-by fixup while looking at all the connector_list walkers -
holding connection_mutex does actually _not_ give you locking to look
at the legacy drm_connector->encoder->crtc pointer chain. That one is
solely owned by the atomic commit workers. Instead we must inspect the
atomic state.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-4-daniel.vetter@ffwll.ch
DRM_UT_CORE generates way too much noise usually, so having the
framebuffer init failures use DRM_UT_CORE is a pain when trying to
find out the reason why you failed in creating a framebuffer.
Let's use DRM_UT_KMS for these debug messages instead.
v2: s/at less than/at most/ in the debug message (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307194210.13400-6-ville.syrjala@linux.intel.com
Let's try to keep the alignment requirements in one place, and so
towards that end let's move the AUX_DIST alignment handling into
intel_surf_alignment() alongside the main surface alignment stuff.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307194210.13400-3-ville.syrjala@linux.intel.com
printks are slow so we should not be doing them from the vblank evade
critical section. These could explain why we sometimes seem to
blow past our 100 usec deadline.
The problem has been there ever since commit bfd16b2a23 ("drm/i915:
Make updating pipe without modeset atomic.") but it may not have
been readily visible until commit e1edbd44e2 ("drm/i915: Complain
if we take too long under vblank evasion.") increased our chances
of noticing it.
Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: bfd16b2a23 ("drm/i915: Make updating pipe without modeset atomic.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307205419.19447-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Backmerge drm-next to get at all the good stuff in drm-misc. We need
that because:
- drm_connector_list_iter conversion for i915 needs the core patches.
- Maarten's patches to use the new atomic state iterators also need
the core patches.
- We need the new link status property to complete the DP retraining
work, merging through 2 branches wasn't a good idea and we had to
partially backtrack.
- Chris needs reservation_object_trylock and we want to roll out
kref_read everywhere.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
4 weeks worth of stuff since I was traveling&lazy:
- lspcon improvements (Imre)
- proper atomic state for cdclk handling (Ville)
- gpu reset improvements (Chris)
- lots and lots of polish around fences, requests, waiting and
everything related all over (both gem and modeset code), from Chris
- atomic by default on gen5+ minus byt/bsw (Maarten did the patch to
flip the default, really this is a massive joint team effort)
- moar power domains, now 64bit (Ander)
- big pile of in-kernel unit tests for various gem subsystems (Chris),
including simple mock objects for i915 device and and the ggtt
manager.
- i915_gpu_info in debugfs, for taking a snapshot of the current gpu
state. Same thing as i915_error_state, but useful if the kernel didn't
notice something is stick. From Chris.
- bxt dsi fixes (Umar Shankar)
- bxt w/a updates (Jani)
- no more struct_mutex for gem object unreference (Chris)
- some execlist refactoring (Tvrtko)
- color manager support for glk (Ander)
- improve the power-well sync code to better take over from the
firmware (Imre)
- gem tracepoint polish (Tvrtko)
- lots of glk fixes all around (Ander)
- ctx switch improvements (Chris)
- glk dsi support&fixes (Deepak M)
- dsi fixes for vlv and clanups, lots of them (Hans de Goede)
- switch to i915.ko types in lots of our internal modeset code (Ander)
- byt/bsw atomic wm update code, yay (Ville)
* tag 'drm-intel-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-intel: (432 commits)
drm/i915: Update DRIVER_DATE to 20170306
drm/i915: Don't use enums for hardware engine id
drm/i915: Split breadcrumbs spinlock into two
drm/i915: Refactor wakeup of the next breadcrumb waiter
drm/i915: Take reference for signaling the request from hardirq
drm/i915: Add FIFO underrun tracepoints
drm/i915: Add cxsr toggle tracepoint
drm/i915: Add VLV/CHV watermark/FIFO programming tracepoints
drm/i915: Add plane update/disable tracepoints
drm/i915: Kill level 0 wm hack for VLV/CHV
drm/i915: Workaround VLV/CHV sprite1->sprite0 enable underrun
drm/i915: Sanitize VLV/CHV watermarks properly
drm/i915: Only use update_wm_{pre,post} for pre-ilk platforms
drm/i915: Nuke crtc->wm.cxsr_allowed
drm/i915: Compute proper intermediate wms for vlv/cvh
drm/i915: Skip useless watermark/FIFO related work on VLV/CHV when not needed
drm/i915: Compute vlv/chv wms the atomic way
drm/i915: Compute VLV/CHV FIFO sizes based on the PM2 watermarks
drm/i915: Plop vlv/chv fifo sizes into crtc state
drm/i915: Plop vlv wm state into crtc_state
...
To prevent having to preserve the drm_crtc_state as we clear the
intel_crtc_state, only memset our extended state.
Fixes:
drivers/gpu/drm/i915/intel_display.c: In function ‘clear_intel_crtc_state’:
drivers/gpu/drm/i915/intel_display.c:11301:1: error: the frame size of 1056 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
v2: Add a comment and BUILD_BUG_ON to explain the memset()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303154644.6709-1-chris@chris-wilson.co.uk
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This cannot be done reliably during vblank evasasion
since the color management registers are not double buffered.
The original commit that moved it always during vblank evasion was
wrong, so revert it to before vblank evasion again.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 20a34e78f0 ("drm/i915: Update color management during vblank evasion.")
Cc: stable@vger.kernel.org # v4.7+
Link: http://patchwork.freedesktop.org/patch/msgid/1488292128-14540-1-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Add tracepoints for plane programming. The tracepoints will dump
the frame and scanline counters, so this can be used to verify eg. that
the plane gets reprogrammed at the right time with respect to watermark
programming (if we have appropriate tracepoints for that as well).
v2: Rebase due to legacy cursor changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-16-ville.syrjala@linux.intel.com
Clear out the watermark for all disabled planes to 0. This is required
to avoid falsely thinking that the inherited watermarks are bogus in
case the watermark is actually higher than the FIFO size.
v2: s/noninverted/raw/ for consistency with other platforms
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-13-ville.syrjala@linux.intel.com
Now that vlv/chv have more proper wm programming support, let's reduce
the the update_wm_{pre,post} flags to only cover the pre-ilk platforms.
When we finally convert those as well we can drop these flags entirely.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-12-ville.syrjala@linux.intel.com
Remove crtc->wm.cxsr_allowed and just rely on crtc_state->disable_cxsr
instead. This was used only by vlv/chv to indicate whether to enable
cxsr in the wm computation. That doesn't really work anymore, and as far
as the optimal watermarks go we'll just consider the number of planes
and the current pipe, and for the intermediate watermarks we'll also
start to consider disable_cxsr which is set appropriately when planes
are being enabled/disabled.
We'll also flip over the crtc_state->wm.need_postvbl_update setup so
that it's the wm code that will set it. Previously the generic code set
it up, and then the wm code cleared it again if it thought it's not
needed after all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-11-ville.syrjala@linux.intel.com
Start computing the vlv/chv watermarks the atomic way, from the
.compute_pipe_wm() hook. We'll recompute the actual watermarks
for only planes that are part of the state, the other planes will
keep their watermark from the last time it was computed.
And the actual watermark programming will happen from the
.initial_watermarks() hook. For now we'll just compute the
optimal watermarks, and we'll hook up the intermediate
watermarks properly later.
The DSPARB registers responsible for the FIFO paritioning are
double buffered, so they will be programming from
intel_begin_crtc_commit().
v2: s/noninverted/raw/ for consistency with other platforms
s/vlv_plane_wm_set/vlv_raw_plane_wm_set/ for clarity
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-8-ville.syrjala@linux.intel.com
In a lot of place we wish to know which planes on the crtc are actually
visible, or how many of them there are. Let's start tracking that in a
bitmask in the crtc state.
We already track enabled planes (ie. ones with an fb and crtc specified by
the user) but that's not quite the same thing as enabled planes may
still end up being invisible due to clipping and whatnot.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-2-ville.syrjala@linux.intel.com
Remove direct usages of intel_crtc->config from the DDI code. Functions
that didn't yet take a pipe_config as an argument were coverted to do
so.
v2: s/pipe_config/const crtc_state/ (Ville)
- take crtc from crtc_state. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-7-ander.conselvan.de.oliveira@intel.com
Pass intel_crtc to functions intel_ddi_enable_transcoder_func(),
intel_ddi_set_pipe_settings() and intel_ddi_set_vc_payload_alloc(),
instead of the generic crtc type. By changing the functions
intel_ddi_get_crtc_encoder() so that it receives an intel_crtc
parameter, there is no need for the drm_crtc in the callers.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-6-ander.conselvan.de.oliveira@intel.com
It is preferred to pass pipe_config to functions instead of accessing
crtc->config directly. Follow suit and pass pipe_config to the fdi link
train functions.
v2: Add const; s/pipe_config/crtc_state/ (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-5-ander.conselvan.de.oliveira@intel.com
Using crtc->config directly is being removed in favor of passing a
pipe_config. Follow the trend and pass pipe_config to pch_enable()
functions.
v2: s/pipe_config/crtc_state/ (Ville)
- constify crtc_state. (Ville)
- take crtc from crtc_state. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-4-ander.conselvan.de.oliveira@intel.com
Currently ILK-BDW explicitly disable LP1+ watermarks from their
.init_clock_gating() hooks. Unfortunately that hook gets called way too
late since by that time we've already initialized all the watermark
state tracking which then gets out of sync with the hardware state.
We may eventually want to consider killing off the explicit LP1+
disable from .init_clock_gating(). In the meantime however, we can
avoid the problem by reordering the init sequence such that
intel_modeset_init_hw()->intel_init_clock_gating() gets called
prior to the hardware state takeover.
I suppose prior to the two stage watermark programming we were
magically saved by something that forced the watermarks to be
reprogrammed fully after .init_clock_gating() got called. But
now that no longer happens.
Note that the diff might look a bit odd as it kills off one
call of intel_update_cdclk(), but that's fine because
intel_modeset_init_hw() does the exact same thing. Previously
we just did it twice.
Actually even this new init sequence is pretty bogus as
.init_clock_gating() really should be called before any gem
hardware init since it can configure various clock gating
workarounds and whatnot that affect the GT side as well. Also
intel_modeset_init() really should get split up into better
defined init stages. Another "fun" detail is that
intel_modeset_gem_init() is where RPS/RC6 gets configured.
Why that is done from the display code is beyond me. I've
decided to leave all this be for now, and just try to fix
the init sequence enough for watermarks to work.
Cc: stable@vger.kernel.org
Cc: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Cc: David Purton <dcpurton@marshwiggle.net>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reported-by: David Purton <dcpurton@marshwiggle.net>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96645
Fixes: ed4a6a7ca8 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170220140443.30891-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to make cursor updates actually safe wrt. watermark programming
we have to clear the legacy_cursor_update flag in the atomic state. That
will cause the regular atomic update path to do the necessary vblank
wait after the plane update if needed, otherwise the vblank wait would
be skipped and we'd feed the optimal watermarks to the hardware before
the plane update has actually happened.
To make the slow vs. fast path determination in
intel_legacy_cursor_update() a little simpler we can ignore the actual
visibility of the plane (which can only get computed once we've already
chosen out path) and instead we simply check whether the fb is being
set or cleared by the user. This means a fully clipped but logically
visible cursor will be considered visible as far as watermark
programming is concerned. We can do that for the cursor since it's a
fixed size plane and the clipped size doesn't play a role in the
watermark computation.
This should fix underruns that can occur when the cursor gets
enable/disabled or the size gets changed. Hopefully it's good enough
that only pure cursor movement and flips go through unthrottled.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Reported-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Fixes: f79f26921e ("drm/i915: Add a cursor hack to allow converting legacy page flip to atomic, v3.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170217150159.11683-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: Rafael Ristovski <rafael.ristovski@gmail.com>
Reintroduce a lock around tiling vs framebuffer creation to prevent
modification of the obj->tiling_and_stride whilst the framebuffer is
being created. Rather than use struct_mutex once again, use the
per-object lock - this will also be required in future to prevent
changing the tiling whilst submitting rendering.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 24dbf51a55 ("drm/i915: struct_mutex is not required for allocating the framebuffer")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301154128.2841-2-chris@chris-wilson.co.uk
No more direct return -EINVAL as we have to unwind the
obj->framebuffer_references.
Fixes: 24dbf51a55 ("drm/i915: struct_mutex is not required for allocating the framebuffer")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301154128.2841-1-chris@chris-wilson.co.uk
According to bspec, the DDI IO power domains should be enabled after
enabling the DPLL and mapping it to the DDI. The current order doesn't
seem to create problems with Skylake and Kabylake, but causes enable
timeouts in Geminilake.
v2: Rebase.
- Take power domain references before sanitizing encoders. (Imre)
- Add comment to get_encoder_power_domains() defition. (Ander)
v3: Don't put the domain if called with HSW/BDW's analog encoder. (CI)
v4: Put IO power domain before unmapping DPLL. (Imre)
- Change return type of intel_ddi_get_power_domains() to u64. (Imre)
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com> # v1
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224141959.5955-1-ander.conselvan.de.oliveira@intel.com
Backmerge the main pull request to sync up with all the newly landed
drivers. Otherwise we'll have chaos even before 4.12 started in
earnest.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYoM2fAAoJEHm+PkMAQRiGr9MH/izEAMri7rJ0QMc3ejt+WmD0
8pkZw3+MVn71z6cIEgpzk4QkEWJd5rfhkETCeCp7qQ9V6cDW1FDE9+0OmPjiphDt
nnzKs7t7skEBwH5Mq5xygmIfkv+Z0QGHZ20gfQWY3F56Uxo+ARF88OBHBLKhqx3v
98C7YbMFLKBslKClA78NUEIdx0UfBaRqerlERx0Lfl9aoOrbBS6WI3iuREiylpih
9o7HTrwaGKkU4Kd6NdgJP2EyWPsd1LGalxBBjeDSpm5uokX6ALTdNXDZqcQscHjE
RmTqJTGRdhSThXOpNnvUJvk9L442yuNRrVme/IqLpxMdHPyjaXR3FGSIDb2SfjY=
=VMy8
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rc8' into drm-next
Linux 4.10-rc8
Backmerge Linus rc8 to fix some conflicts, but also
to avoid pulling it in via a fixes pull from someone.
Setting retire=true is identical to using origin=ORIGIN_CS, so make the
same simplification to intel_fb_obj_flush() as already employed for
intel_fb_obj_invalidate().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222114049.28456-6-chris@chris-wilson.co.uk
Flushing the cachelines for an object is slow, can be as much as 100ms
for a large framebuffer. We currently do this under the struct_mutex BKL
on execution or on pageflip. But now with the ability to add fences to
obj->resv for both flips and execbuf (and we naturally wait on the fence
before CPU access), we can move the clflush operation to a workqueue and
signal a fence for completion, thereby doing the work asynchronously and
not blocking the driver or its clients.
v2: Introduce i915_gem_clflush.h and use a new name, split out some
extras into separate patches.
Suggested-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222114049.28456-5-chris@chris-wilson.co.uk
We have three different paths by which userspace wants to flush the
display plane (i.e. objects with obj->pin_display). Use a common helper
to identify those paths and to simplify a later change.
v2: Include the conditional in the name, i915_gem_object_flush_if_display
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222114049.28456-3-chris@chris-wilson.co.uk
Verify that the refcount of all power wells match their HW enabled
state at the end of modeset HW state readout.
Also add documentation on how the reference count for each power well is
supposed to be acquired during initialization and HW state readout.
Suggested by Ander.
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487345986-26511-6-git-send-email-imre.deak@intel.com
We do not need the BKL struct_mutex in order to allocate a GEM object,
nor to create the framebuffer, so resist the temptation to take the BKL
willy nilly. As this changes the locking contract around internal API
calls, the patch is a little larger than a plain removal of a pair of
mutex_lock/unlock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170215105919.7347-2-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We do not need to hold struct_mutex for destroying drm_i915_gem_objects
any longer, and with a little care taken over tracking
obj->framebuffer_references, we can relinquish BKL locking around the
destroy of intel_framebuffer.
v2: Use atomic check for WARN_ON framebuffer miscounting
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170216094621.3426-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Once upon a time before we had automated GPU state capture upon hangs,
we had intel_gpu_dump. Now we come almost full circle and reinstate that
view of the current GPU queues and registers by using the error capture
facility to snapshot the GPU state when debugfs/.../i915_gpu_info is
opened - which should provided useful debugging to both the error
capture routines (without having to cause a hang and avoid the error
state being eaten by igt) and generally.
v2: Rename drm_i915_error_state to i915_gpu_state to alleviate some name
collisions between the error state dump and inspecting the gpu state.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170214164611.11381-1-chris@chris-wilson.co.uk
Add for_each_(old)(new)_(plane,connector,crtc)_in_state iterators to
replace the old for_each_xxx_in_state ones. This is useful for >1 flip
depth and getting rid of all xxx->state dereferences.
This requires extra fixups done when committing a state after
duplicating, which in general isn't valid but is used by suspend/resume.
To handle these, introduce drm_atomic_helper_commit_duplicated_state
which performs those fixups before checking & committing the state.
Changes since v1:
- Remove nonblock parameter for commit_duplicated_state.
Changes since v2:
- Use commit_duplicated_state for i915 load detection.
- Add WARN_ON(old_state != obj->state) before swapping.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1484559464-27107-2-git-send-email-maarten.lankhorst@linux.intel.com
This removes the usage of intel_ring_emit in favour of
directly writing to the ring buffer.
intel_ring_emit was preventing the compiler for optimising
fetch and increment of the current ring buffer pointer and
therefore generating very verbose code for every write.
It had no useful purpose since all ringbuffer operations
are started and ended with intel_ring_begin and
intel_ring_advance respectively, with no bail out in the
middle possible, so it is fine to increment the tail in
intel_ring_begin and let the code manage the pointer
itself.
Useless instruction removal amounts to approximately
two and half kilobytes of saved text on my build.
Not sure if this has any measurable performance
implications but executing a ton of useless instructions
on fast paths cannot be good.
v2:
* Change return from intel_ring_begin to error pointer by
popular demand.
* Move tail increment to intel_ring_advance to enable some
error checking.
v3:
* Move tail advance back into intel_ring_begin.
* Rebase and tidy.
v4:
* Complete rebase after a few months since v3.
v5:
* Remove unecessary cast and fix !debug compile. (Chris Wilson)
v6:
* Make intel_ring_offset take request as well.
* Fix recording of request postfix plus a sprinkle of asserts.
(Chris Wilson)
v7:
* Use intel_ring_offset to get the postfix. (Chris Wilson)
* Convert GVT code as well.
v8:
* Rename *out++ to *cs++.
v9:
* Fix GVT out to cs conversion in GVT.
v10:
* Rebase for new intel_ring_begin in selftests.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170214113242.29241-1-tvrtko.ursulin@linux.intel.com
I screwed up the rebase of commit d8fc70b736 ("drm/i915: Make power
domain masks 64 bit long") before sending v2, causing a couple of
conversions from 32 to 64 bit masks to be lost.
Fixes: d8fc70b736 ("drm/i915: Make power domain masks 64 bit long")
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170213145733.8779-1-ander.conselvan.de.oliveira@intel.com
There are currently 30 power domains, which puts us pretty close to the
limit with 32 bit masks. Prepare for the future and increase the limit
to 64 bit.
v2: Rebase
v3: s/unsigned long long/u64/ (Joonas)
Allow the 64th bit of the mask to be used. (Joonas)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170209093121.24410-1-ander.conselvan.de.oliveira@intel.com
With the cdclk state, all the .modeset_commit_cdclk() hooks are
now pointless wrappers. Let's replace them with just a .set_cdclk()
function pointer. However let's wrap that in a small helper that
does the state comparison and prints a unified debug message across
all platforms. We didn't even have the debug print on all platforms
previously. This reduces the clutter in intel_atomic_commit_tail() a
little bit.
v2: Wrap .set_cdclk() in intel_set_cdclk()
v3: Add kernel-docs
v4: Deal with IS_GEN9_BC()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126195201.32638-1-ville.syrjala@linux.intel.com
The current dev_cdclk vs. cdclk vs. atomic_cdclk_freq is quite a mess.
So here I'm introducing the "actual" and "logical" naming for our
cdclk state. "actual" is what we'll bash into the hardware and "logical"
is what everyone should use for state computaion/checking and whatnot.
We'll track both using the intel_cdclk_state as both will need other
differing parameters than just the actual cdclk frequency.
While doing that we can at the same time unify the appearance of the
.modeset_calc_cdclk() implementations a little bit.
v2: Commit dev_priv->cdclk.actual since that already has the
new state by the time .modeset_commit_cdclk() is called.
v3: s/locical/logical/ and improve the docs a bit
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170120182205.8141-9-ville.syrjala@linux.intel.com
Introduce intel_cdclk state which for now will track the cdclk
frequency, the vco frequency and the reference frequency (not sure we
want the last one, but I put it there anyway). We'll also make the
.get_cdclk() function fill out this state structure rather than
just returning the current cdclk frequency.
One immediate benefit is that calling .get_cdclk() will no longer
clobber state stored under dev_priv unless ex[plicitly told to do
so. Previously it clobbered the vco and reference clocks stored
there on some platforms.
We'll expand the use of this structure to actually precomputing the
state and whatnot later.
v2: Constify intel_cdclk_state_compare()
v3: Document intel_cdclk_state_compare()
v4: Deal with i945gm_get_cdclk()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207183345.19763-1-ville.syrjala@linux.intel.com
Let's try to shrink intel_display.c a bit by moving the cdclk/rawclk
stuff to a new file. It's all reasonably self contained so we don't
even have to add that many non-static symbols.
We'll also take the opportunity to shuffle around the functions a bit
to get things in a more consistent order based on the platform.
v2: Add kernel-docs (Ander)
v3: Deal with IS_GEN9_BC()
v4: Deal with i945gm_get_cdclk()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207183305.19656-1-ville.syrjala@linux.intel.com
Let's clean up the mess we have in the if ladder that assigns the
.get_cdclk() hooks. The grouping of the platforms by the function
results in a thing that's not really legible, so let's do it the
other way around and order the if ladder by platform and duplicate
whatever assignments we need.
To further avoid confusion with the function names let's rename
them to just fixed_<freq>_get_cdclk(). The other option would
be to duplicate the functions entirely but it seems quite
pointless to do that since each one just returns a fixed value.
v2: Deal with i945gm_get_cdclk()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207183226.19537-1-ville.syrjala@linux.intel.com
Rename the .get_display_clock_speed() hook to .get_cdclk().
.get_cdclk() is more specific (which clock) and it's much
shorter.
v2: Deal with IS_GEN9_BC()
v3: Deal with i945gm_get_display_clock_speed()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207183146.19420-1-ville.syrjala@linux.intel.com
ilk_max_pixel_rate() will now give the "correct" pixel rate for all
platforms, so let's rename it to intel_max_pixel_rate() and kill
off intel_mode_max_pixclk().
v2: Fix typo in commit message (Ander)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170120182205.8141-3-ville.syrjala@linux.intel.com
Rather than recomputing the pipe pixel rate on demand everywhere, let's
just stick the precomputed value into the crtc state.
v2: Rebase due to min_pixclk[] code movement
Document the new pixel_rate struct member (Ander)
Combine vlv/chv with bdw+ in intel_modeset_readout_hw_state()
v3: Fix typos in commit message (David)
Cc: Ander Conselvan De Oliveira <conselvan2@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126195031.32343-1-ville.syrjala@linux.intel.com
If we have any residual freed atomic state from earlier commits, flush
the freed list after performing the current modeset. This prevents the
freed list from ever-growing if userspace manages to starve the kernel
threads (i.e. we are never able to run our free state worker and
eventually the system may even oom).
Fixes: eb955eee27 ("drm/i915: Move atomic state free from out of fence release")
Testcase: igt/kms_cursor/legacy/all-pipes-single-bo
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202204741.18231-1-chris@chris-wilson.co.uk
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Chris Wilson wants the new fence tracepoint added in
commit 8c96c67801
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Jan 24 11:57:58 2017 +0000
dma/fence: Export enable-signaling tracepoint for emission by drivers
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Another round of -misc stuff:
- Noralf debugfs cleanup cleanup (not yet everything, some more driver
patches awaiting acks).
- More doc work.
- edid/infoframe fixes from Ville.
- misc 1-patch fixes all over, as usual
Noralf needs this for his tinydrm pull request.
* tag 'drm-misc-next-2017-01-30' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
drm/vc4: Remove vc4_debugfs_cleanup()
dma/fence: Export enable-signaling tracepoint for emission by drivers
drm/tilcdc: Remove tilcdc_debugfs_cleanup()
drm/tegra: Remove tegra_debugfs_cleanup()
drm/sti: Remove drm_debugfs_remove_files() calls
drm/radeon: Remove drm_debugfs_remove_files() call
drm/omap: Remove omap_debugfs_cleanup()
drm/hdlcd: Remove hdlcd_debugfs_cleanup()
drm/etnaviv: Remove etnaviv_debugfs_cleanup()
drm/etnaviv: allow build with COMPILE_TEST
drm/amd/amdgpu: Remove drm_debugfs_remove_files() call
drm/prime: Clarify DMA-BUF/GEM Object lifetime
drm/ttm: Make sure BOs being swapped out are cacheable
drm/atomic: Remove drm_atomic_debugfs_cleanup()
drm: drm_minor_register(): Clean up debugfs on failure
drm: debugfs: Remove all files automatically on cleanup
drm/fourcc: add vivante tiled layout format modifiers
drm/edid: Set YQ bits in the AVI infoframe according to CEA-861-F
drm/edid: Set AVI infoframe Q even when QS=0
drm/edid: Introduce drm_hdmi_avi_infoframe_quant_range()
...
In Geminilake, the bits for enabling pipe csc, pipe gamma and plane
gamma moved to a new register. So update the plane update functions
to set the right bits.
Pipe CSC is kept disabled though, since enabling that also enables the
dedicated degamma table, and that is not properly programmed yet,
leading to a black screen.
v2: Use plane_id. (Ville)
Remove unnecessary variable. (Ville)
Keep registers in offset order. (Ville)
Don't set plane gamma disable twice. (Ander)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485429865-10687-3-git-send-email-ander.conselvan.de.oliveira@intel.com
I've seen this trigger twice now, where the i915_gem_object_to_ggtt()
call in intel_unpin_fb_obj() returns NULL, resulting in an oops
immediately afterwards as the (inlined) call to i915_vma_unpin_fence()
tries to dereference it.
It seems to be some race condition where the object is going away at
shutdown time, since both times happened when shutting down the X
server. The call chains were different:
- VT ioctl(KDSETMODE, KD_TEXT):
intel_cleanup_plane_fb+0x5b/0xa0 [i915]
drm_atomic_helper_cleanup_planes+0x6f/0x90 [drm_kms_helper]
intel_atomic_commit_tail+0x749/0xfe0 [i915]
intel_atomic_commit+0x3cb/0x4f0 [i915]
drm_atomic_commit+0x4b/0x50 [drm]
restore_fbdev_mode+0x14c/0x2a0 [drm_kms_helper]
drm_fb_helper_restore_fbdev_mode_unlocked+0x34/0x80 [drm_kms_helper]
drm_fb_helper_set_par+0x2d/0x60 [drm_kms_helper]
intel_fbdev_set_par+0x18/0x70 [i915]
fb_set_var+0x236/0x460
fbcon_blank+0x30f/0x350
do_unblank_screen+0xd2/0x1a0
vt_ioctl+0x507/0x12a0
tty_ioctl+0x355/0xc30
do_vfs_ioctl+0xa3/0x5e0
SyS_ioctl+0x79/0x90
entry_SYSCALL_64_fastpath+0x13/0x94
- i915 unpin_work workqueue:
intel_unpin_work_fn+0x58/0x140 [i915]
process_one_work+0x1f1/0x480
worker_thread+0x48/0x4d0
kthread+0x101/0x140
and this patch purely papers over the issue by adding a NULL pointer
check and a WARN_ON_ONCE() to avoid the oops that would then generally
make the machine unresponsive.
Other callers of i915_gem_object_to_ggtt() seem to also check for the
returned pointer being NULL and warn about it, so this clearly has
happened before in other places.
[ Reported it originally to the i915 developers on Jan 8, applying the
ugly workaround on my own now after triggering the problem for the
second time with no feedback.
This is likely to be the same bug reported as
https://bugs.freedesktop.org/show_bug.cgi?id=98829https://bugs.freedesktop.org/show_bug.cgi?id=99134
which has a patch for the underlying problem, but it hasn't gotten to
me, so I'm applying the workaround. ]
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The intel_dp_autotest_video_pattern() function gets invoked through the
compliance test handler on a HPD short pulse if the test type is
set to DP_TEST_VIDEO_PATTERN. This performs the DPCD registers
reads to read the requested test pattern, video pattern resolution,
frame rate and bits per color value. The results of this analysis
are handed off to userspace so that the userspace app can set the
video pattern mode appropriately for the test result/response.
When the test is requested with specific BPC value, we read the BPC
value from the DPCD register. If this BPC value in intel_dp structure
has a non-zero value and we're on a display port connector, then we use
the value to calculate the bpp for the pipe. Also in this case if its
a 18bpp video pattern request, then we force the dithering on pipe to be
disabled since it causes CRC mismatches.
The compliance_test_active flag is set at the end of the individual
test handling functions. This is so that the kernel-side operations
can be completed without the risk of interruption from the userspace
app that is polling on that flag.
v5:
* Remove test_result variable
* Populate the compliance test data at the end of the function (Jani Nikula)
v4:
*Return TEST_NAK on read failures and invalid values (Jani Nikula)
* Address CRC mismatch errors
v3:
* Use the updated properly shifted bit definitions (Jani Nikula)
* Force dithering to be disabled on 18bpp compliance
test request (Manasi Navare)
v2:
* Updated the DPCD Register reads based on proper defines in header (Jani Nikula)
* Squahsed the patch that forced the pipe bpp to compliance test bpp (Jani Nikula)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485274909-17470-1-git-send-email-manasi.d.navare@intel.com
In intel_crtc_disable_noatomic(), bail on a failure to allocate an
atomic state to avoid a NULL pointer dereference.
Fixes: 4a80655827 ("drm/i915: Pass atomic state to crtc enable/disable functions")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484922525-6131-4-git-send-email-ander.conselvan.de.oliveira@intel.com
(cherry picked from commit 31bb2ef97e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Parameters tile_size, tile_width and tile_height were passed in the
wrong order to _intel_adjust_tile_offset() when calculating the rotated
offsets.
This doesn't fix any user visible bug, since for packed formats new
and old offset are the same and the rotated offsets are within a tile
before they are fed to _intel_adjust_tile_offset(). In that case, the
offsets are unchanged. That is not true for planar formats, but those
are currently not supported.
Fixes: 66a2d927cb ("drm/i915: Make intel_adjust_tile_offset() work for linear buffers")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484922525-6131-3-git-send-email-ander.conselvan.de.oliveira@intel.com
(cherry picked from commit 46a1bd2895)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
After we call drm_atomic_commit() on the load-detect state, we can free
our local reference. Upon restore, we only apply and free the previous state.
Fixes: 0853695c3b ("drm: Add reference counting to drm_atomic_state")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170119113749.2517-1-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 7abbd11f34)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
intel_display_resume() may be called without an atomic state to restore,
i.e. dev_priv->modeset_reset_restore state is NULL. One such case is
following a lid open/close event and the forced modeset in
intel_lid_notify().
Reported-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Tested-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Fixes: 0853695c3b ("drm: Add reference counting to drm_atomic_state")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170115125825.18597-1-chris@chris-wilson.co.uk
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
(cherry picked from commit 3c5e37f169)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Along with GLK it was introduced the .is_lp and IS_GEN9_LP.
So, following the same simplification standard we can
put Skylake and Kabylake under the same bucket for most
of the things.
So let's add the IS_GEN9_BC for "Big Core" (non Atom based
platforms).
The i915_drv.c was let out of this patch on purpose
because that is really a decision per platform, just like
other cases where IS_KABYLAKE is different from IS_SKYLAKE.
v2: fix conflict with IS_LP and 3 new cases for this
big core bucket:
- intel_ddi.c: intel_ddi_get_link_dpll
- intel_fbc.c: find_compression_threshold
- i915_gem_gtt.c: gtt_write_workarounds
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485196357-30599-2-git-send-email-rodrigo.vivi@intel.com
This reverts commit 527b6abe5f
(Revert "drm/i915: Use atomic commits for legacy page_flips")
and reapplies commit ee042aa40b.
("drm/i915: Use atomic commits for legacy page_flips")
The reason for the revert was because legacy cursor updates were
forced to wait for pending page flips and rendering after they
were converted to atomic.
Commit f79f26921e
(drm/i915: Add a cursor hack to allow converting legacy page flip to atomic, v3)
adds a fastpath to cursor updates, which fixes the stuttering issues.
With these changes I feel confident enough to re-enable cursor updates.
Legacy cursor update won't block in the following cases:
- Moving cursor
- Changing cursor fb
The legacy cursor update will still block in the following cases:
- Showing/hiding cursor.
- Cursor size or scaling changes.
- cursor update while cursor is invisible (could be fixed, if it turns out to be important).
- Cursor tiling changes (Not sure we support tiled cursors.)
- Last update was a modeset.
Cc: Steven Newbury <steve@snewbury.org.uk>
Cc: Rafael Ristovski <rafael.ristovski@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Rafael Ristovski <rafael.ristovski@gmail.com>
Testcase: igt/kms_cursor_legacy
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In intel_crtc_disable_noatomic(), bail on a failure to allocate an
atomic state to avoid a NULL pointer dereference.
Fixes: 4a80655827 ("drm/i915: Pass atomic state to crtc enable/disable functions")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484922525-6131-4-git-send-email-ander.conselvan.de.oliveira@intel.com
Parameters tile_size, tile_width and tile_height were passed in the
wrong order to _intel_adjust_tile_offset() when calculating the rotated
offsets.
This doesn't fix any user visible bug, since for packed formats new
and old offset are the same and the rotated offsets are within a tile
before they are fed to _intel_adjust_tile_offset(). In that case, the
offsets are unchanged. That is not true for planar formats, but those
are currently not supported.
Fixes: 66a2d927cb ("drm/i915: Make intel_adjust_tile_offset() work for linear buffers")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484922525-6131-3-git-send-email-ander.conselvan.de.oliveira@intel.com
crtc->config is on its way out. Let's reduce our dependence on it a
little bit by removing it from intel_modeset_readout_hw_state().
Also replace crtc->acttive checks with crtc_state->base.active checks.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Suggested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161222140442.7204-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After we call drm_atomic_commit() on the load-detect state, we can free
our local reference. Upon restore, we only apply and free the previous state.
Fixes: 0853695c3b ("drm: Add reference counting to drm_atomic_state")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170119113749.2517-1-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
With atomic plane states we are able to track an allocation right from
preparation, during use and through to the final free after being
swapped out for a new plane. We can couple the VMA we pin for the
framebuffer (and its rotation) to this lifetime and avoid all the clumsy
lookups in between.
v2: Remove residual vma on plane cleanup (Chris)
v3: Add a description for the vma destruction in
intel_plane_destroy_state (Maarten)
References: https://bugs.freedesktop.org/show_bug.cgi?id=98829
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170116152131.18089-1-chris@chris-wilson.co.uk
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
When the plane is invisible we may have all sorts of bogus stuff
in the coordinates, which we must ignore or else we might fail the
plane update. This started to happen on SKL when I moved the plane
offset computation to happen in the check phase. Previously we
happily ignored it all since we never called the update_plane hook
with an invisible plane.
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98258
Testcase: igt/pm_rpm/legacy-planes
Testcase: igt/pm_rpm/universal-planes
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478550057-24864-3-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit a5e4c7d0aa)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The error paths in hsw_trans_edp_pipe_A_crc_wa() and
intel_prepare_reset() would potentially call drm_atomic_state_put with a
NULL state, which would lead to a NULL pointer dereference.
Found by coverity.
v2: Improve the error paths. (Chris)
Fixes: 0853695c3b ("drm: Add reference counting to drm_atomic_state")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484742868-9551-1-git-send-email-ander.conselvan.de.oliveira@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
intel_display_resume() may be called without an atomic state to restore,
i.e. dev_priv->modeset_reset_restore state is NULL. One such case is
following a lid open/close event and the forced modeset in
intel_lid_notify().
Reported-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Tested-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Fixes: 0853695c3b ("drm: Add reference counting to drm_atomic_state")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.10-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170115125825.18597-1-chris@chris-wilson.co.uk
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
When the plane is invisible we may have all sorts of bogus stuff
in the coordinates, which we must ignore or else we might fail the
plane update. This started to happen on SKL when I moved the plane
offset computation to happen in the check phase. Previously we
happily ignored it all since we never called the update_plane hook
with an invisible plane.
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98258
Testcase: igt/pm_rpm/legacy-planes
Testcase: igt/pm_rpm/universal-planes
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478550057-24864-3-git-send-email-ville.syrjala@linux.intel.com
It is only being used to clear a struct and set the type, after which it
is overwritten. Since we no longer check the unset bits of the union,
skipping the clear is permissible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170114002827.31315-6-chris@chris-wilson.co.uk
Reading the ggtt_views is much more pleasant without the extra
characters from specifying the union (i.e. ggtt_view.partial rather than
ggtt_view.params.partial). To make this work inside i915_vma_compare()
with only a single memcmp requires us to ensure that there are no
uninitialised bytes within each branch of the union (we make sure the
structs are packed) and we need to store the size of each branch.
v4: Rewrite changelog and add comments explaining the assert.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170114002827.31315-5-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The visible member used to be in intel_plane_state->visible,
but has been moved to drm_plane_state->visible. In the conversion
some casts were left in that are now useless.
to_intel_plane_state(x)->base.visible is the same as x->visible,
so use the latter to clear up the code a little.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484214225-30328-1-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The core provides now an ABI to userspace for generation of frame CRCs,
so implement the ->set_crc_source() callback and reuse as much code as
possible with the previous ABI implementation.
When handling the pageflip interrupt, we skip 1 or 2 frames depending on
the HW because they contain wrong values. For the legacy ABI for
generating frame CRCs, this was done in userspace but now that we have a
generic ABI it's better if it's not exposed by the kernel.
v2:
- Leave the legacy implementation in place as the ABI implementation
in the core is incompatible with it.
v3:
- Use the "cooked" vblank counter so we have a whole 32 bits.
- Make sure we don't mess with the state of the legacy CRC capture
ABI implementation.
v4:
- Keep use of get_vblank_counter as in the legacy code, will be
changed in a followup commit.
v5:
- Skip first frame or two as it's known that they contain wrong
data.
- A few fixes suggested by Emil Velikov.
v6:
- Rework programming of the HW registers to preserve previous
behavior.
v7:
- Address whitespace issue.
- Added a comment on why in the implementation of the new ABI we
skip the 1st or 2nd frames.
v9:
- Add stub for intel_crtc_set_crc_source.
v12:
- Rebased.
- Remove stub for intel_crtc_set_crc_source and instead set the
callback to NULL (Jani Nikula).
v15:
- Rebased.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Robert Foss <robert.foss@collabora.com>
irq
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170110134305.26326-2-tomeu.vizoso@collabora.com
Directly merge drm-misc into drm-intel since Dave is on vacation and
we need the various drm-misc patches (fb format rework, drm mm fixes,
selftest framework and others). Also pulled back -rc2 in first to
resync with drm-intel-fixes and make sure I can reuse the exact rerere
solutions from drm-tip for safety, and because I'm lazy.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The code was moved, but the comment not updated. It confused me.
Fixes: 7f4c62840c ("drm/i915: Assign hwmode after encoder state readout")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161219082423.27798-6-daniel.vetter@ffwll.ch
Trying to determine the pixel rate of the pipe can't be done until we
know the clock, which means it can't be done until the encoder
.get_config() hooks have been called. So let's move the min_pixclk[]
stuff to the end of intel_modeset_readout_hw_state() when we actually
have gathered all the required infromation.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Fixes: 565602d750 ("drm/i915: Do not acquire crtc state to check clock during modeset, v4.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161220153902.15621-1-ville.syrjala@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit aca1ebf491)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In future patches, we require greater flexibility in describing
the number of scalers available on each CRTC. To ease that transition
we move the current assignment to intel_device_info.
Scaler structure initialisation is done if scaler is available on the CRTC.
Gen9 check is not required as on depending upon numbers of scalers we
initialize scalers or return without doing anything in skl_init_scalers.
v3: Changed skl_init_scaler to intel_crtc_init_scalers
v2: Added Chris's comments.
Signed-off-by: Nabendu Maiti <nabendu.bikash.maiti@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480398794-22741-1-git-send-email-nabendu.bikash.maiti@intel.com
Remove the IS_PLATFORM() macros from intel_dump_pipe_config() and split
that logic in platform specific implementations inside the dpll code,
accessed through a platform independent interface.
v2: Rebase.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1483024933-3726-7-git-send-email-ander.conselvan.de.oliveira@intel.com
The function intel_shared_dpll_commit() performs the equivalent of
drm_atomic_helper_swap_state() for the shared dpll state, which is not
handled by the helpers. So make it do a full swap of the state and
rename it for consistency.
v2: Fix typo in the commit message. (Durga)
v3: Rebase.
v4: Swap the states instead of just renaming the function. (Daniel)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com> (v2)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1483024933-3726-3-git-send-email-ander.conselvan.de.oliveira@intel.com
While the details of getting a shared dpll are wrapped by
intel_get_shared_dpll(), the release was still hand rolled into the
modeset code. Fix that by creating an entry point for releasing the
pll and move that code there.
v2: Take old_dpll from crtc->state instead of crtc_state. (CI)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1483024933-3726-2-git-send-email-ander.conselvan.de.oliveira@intel.com
First set of i915 fixes for code in next.
* tag 'drm-intel-next-fixes-2016-12-22' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: skip the first 4k of stolen memory on everything >= gen8
drm/i915: Fallback to single PAGE_SIZE segments for DMA remapping
drm/i915: Fix use after free in logical_render_ring_init
drm/i915: disable PSR by default on HSW/BDW
drm/i915: Fix setting of boost freq tunable
drm/i915: tune down the fast link training vs boot fail
drm/i915: Reorder phys backing storage release
drm/i915/gen9: Fix PCODE polling during SAGV disabling
drm/i915/gen9: Fix PCODE polling during CDCLK change notification
drm/i915/dsi: Fix chv_exec_gpio disabling the GPIOs it is setting
drm/i915/dsi: Fix swapping of MIPI_SEQ_DEASSERT_RESET / MIPI_SEQ_ASSERT_RESET
drm/i915/dsi: Do not clear DPOUNIT_CLOCK_GATE_DISABLE from vlv_init_display_clock_gating
drm/i915: drop the struct_mutex when wedged or trying to reset
Trying to determine the pixel rate of the pipe can't be done until we
know the clock, which means it can't be done until the encoder
.get_config() hooks have been called. So let's move the min_pixclk[]
stuff to the end of intel_modeset_readout_hw_state() when we actually
have gathered all the required infromation.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Fixes: 565602d750 ("drm/i915: Do not acquire crtc state to check clock during modeset, v4.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161220153902.15621-1-ville.syrjala@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
commit 848496e590
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Jul 13 16:32:03 2016 +0300
drm/i915: Wait up to 3ms for the pcu to ack the cdclk change request on SKL
increased the timeout to match the spec, but we still see a timeout on
at least one SKL. A CDCLK change request following the failed one will
succeed nevertheless.
I could reproduce this problem easily by running kms_pipe_crc_basic in a
loop. In all failure cases _wait_for() was pre-empted for >3ms and so in
the worst case - when the pre-emption happened right after calculating
timeout__ in _wait_for() - we called skl_cdclk_wait_for_pcu_ready() only
once which failed and so _wait_for() timed out. As opposed to this the
spec says to keep retrying the request for at most a 3ms period.
To fix this send the first request explicitly to guarantee that there is
3ms between the first and last request. Though this matches the spec, I
noticed that in rare cases this can still time out if we sent only a few
requests (in the worst case 2) _and_ PCODE is busy for some reason even
after a previous request and a 3ms delay. To work around this retry the
polling with pre-emption disabled to maximize the number of requests.
Also increase the timeout to 10ms to account for interrupts that could
reduce the number of requests. With this change I couldn't trigger
the problem.
v2:
- Use 1ms poll period instead of 10us. (Chris)
v3:
- Poll with pre-emption disabled to increase the number of request
attempts. (Ville, Chris)
- Factor out a helper to poll, it's also needed by the next patch.
v4:
- Pass reply_mask, reply to skl_pcode_request(), instead of assuming the
reply is generic. (Ville)
v5:
- List the request specific timeout values as code comment. (Ville)
v6:
- Try the poll first with preemption enabled.
- Add code comment about first request being queued by PCODE. (Art)
- Add timeout_base_ms argument. (Ville)
v7:
- Clarify code comment about first queued request. (Chris)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: <stable@vger.kernel.org> # v4.2- : 3b2c171 : drm/i915: Wait up to 3ms
Cc: <stable@vger.kernel.org> # v4.2-
Fixes: 5d96d8afcf ("drm/i915/skl: Deinit/init the display at suspend/resume")
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=97929
Testcase: igt/kms_pipe_crc_basic/suspend-read-crc-pipe-B
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1480955258-26311-1-git-send-email-imre.deak@intel.com
(cherry picked from commit a0b8a1fe34)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We grab the struct_mutex in intel_crtc_page_flip, but if we are wedged
or a reset is in progress we bail early but never seem to actually
release the lock.
Fixes: 7f1847ebf4 ("drm/i915: Simplify checking of GPU reset_counter in display pageflips")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161128103648.9235-1-matthew.auld@intel.com
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v4.7+
(cherry picked from commit ddbb271aea)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit e411072d57)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Do something similar to vc4, only allow updating the cursor state
in-place through a fastpath when the watermarks are unaffected. This
will allow cursor movement to be smooth, but changing cursor size or
showing/hiding cursor will still fall back so watermarks can be updated.
Only moving and changing fb is allowed.
Changes since v1:
- Set page flip to always_unused for trybot.
- Copy fence correctly, ignore plane_state->state, should be NULL.
- Check crtc_state for !active and modeset, go to slowpath if the case.
Changes since v2:
- Make error handling work correctly. (Matthew Auld)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/a8e4cb00-5171-14e5-bbe3-dadb654ff296@linux.intel.com
The requests conversion introduced a nasty bug where we could generate a
new request in the middle of constructing a request if we needed to idle
the system in order to evict space for a context. The request to idle
would be executed (and waited upon) before the current one, creating a
minor havoc in the seqno accounting, as we will consider the current
request to already be completed (prior to deferred seqno assignment) but
ring->last_retired_head would have been updated and still could allow
us to overwrite the current request before execution.
We also employed two different mechanisms to track the active context
until it was switched out. The legacy method allowed for waiting upon an
active context (it could forcibly evict any vma, including context's),
but the execlists method took a step backwards by pinning the vma for
the entire active lifespan of the context (the only way to evict was to
idle the entire GPU, not individual contexts). However, to circumvent
the tricky issue of locking (i.e. we cannot take struct_mutex at the
time of i915_gem_request_submit(), where we would want to move the
previous context onto the active tracker and unpin it), we take the
execlists approach and keep the contexts pinned until retirement.
The benefit of the execlists approach, more important for execlists than
legacy, was the reduction in work in pinning the context for each
request - as the context was kept pinned until idle, it could short
circuit the pinning for all active contexts.
We introduce new engine vfuncs to pin and unpin the context
respectively. The context is pinned at the start of the request, and
only unpinned when the following request is retired (this ensures that
the context is idle and coherent in main memory before we unpin it). We
move the engine->last_context tracking into the retirement itself
(rather than during request submission) in order to allow the submission
to be reordered or unwound without undue difficultly.
And finally an ulterior motive for unifying context handling was to
prepare for mock requests.
v2: Rename to last_retired_context, split out legacy_context tracking
for MI_SET_CONTEXT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161218153724.8439-3-chris@chris-wilson.co.uk
Rather than compare the format u32s of two format infos, we can direclty
compare the format info pointers themselves. Noramlly all the ->format
pointers all point to somwehere in the big array, so this is a valid
way to test for equality.
Also drivers may want to point ->format at a private format info struct
instead (eg. for special compressed formats with extra planes), so
just comparing the pixel format values wouldn't necessaritly even work.
But comparing the pointers will also take care of that case.
@@
struct drm_framebuffer *a;
struct drm_framebuffer *b;
@@
(
- a->format->format != b->format->format
+ a->format != b->format
|
- a->format->format == b->format->format
+ a->format == b->format
)
@@
struct drm_plane_state *a;
struct drm_plane_state *b;
@@
(
- a->fb->format->format != b->fb->format->format
+ a->fb->format != b->fb->format
|
- a->fb->format->format == b->fb->format->format
+ a->fb->format == b->fb->format
)
@@
struct drm_crtc *crtc;
struct drm_framebuffer *x;
@@
(
- crtc->primary->fb->format->format != x->format->format
+ crtc->primary->fb->format != x->format
|
- x->format->format != crtc->primary->fb->format->format
+ x->format != crtc->primary->fb->format
)
@@
struct drm_mode_set *set;
@@
- set->fb->format->format != set->crtc->primary->fb->format->format
+ set->fb->format != set->crtc->primary->fb->format
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479498793-31021-35-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
commit 848496e590
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Jul 13 16:32:03 2016 +0300
drm/i915: Wait up to 3ms for the pcu to ack the cdclk change request on SKL
increased the timeout to match the spec, but we still see a timeout on
at least one SKL. A CDCLK change request following the failed one will
succeed nevertheless.
I could reproduce this problem easily by running kms_pipe_crc_basic in a
loop. In all failure cases _wait_for() was pre-empted for >3ms and so in
the worst case - when the pre-emption happened right after calculating
timeout__ in _wait_for() - we called skl_cdclk_wait_for_pcu_ready() only
once which failed and so _wait_for() timed out. As opposed to this the
spec says to keep retrying the request for at most a 3ms period.
To fix this send the first request explicitly to guarantee that there is
3ms between the first and last request. Though this matches the spec, I
noticed that in rare cases this can still time out if we sent only a few
requests (in the worst case 2) _and_ PCODE is busy for some reason even
after a previous request and a 3ms delay. To work around this retry the
polling with pre-emption disabled to maximize the number of requests.
Also increase the timeout to 10ms to account for interrupts that could
reduce the number of requests. With this change I couldn't trigger
the problem.
v2:
- Use 1ms poll period instead of 10us. (Chris)
v3:
- Poll with pre-emption disabled to increase the number of request
attempts. (Ville, Chris)
- Factor out a helper to poll, it's also needed by the next patch.
v4:
- Pass reply_mask, reply to skl_pcode_request(), instead of assuming the
reply is generic. (Ville)
v5:
- List the request specific timeout values as code comment. (Ville)
v6:
- Try the poll first with preemption enabled.
- Add code comment about first request being queued by PCODE. (Art)
- Add timeout_base_ms argument. (Ville)
v7:
- Clarify code comment about first queued request. (Chris)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: <stable@vger.kernel.org> # v4.2- : 3b2c171 : drm/i915: Wait up to 3ms
Cc: <stable@vger.kernel.org> # v4.2-
Fixes: 5d96d8afcf ("drm/i915/skl: Deinit/init the display at suspend/resume")
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=97929
Testcase: igt/kms_pipe_crc_basic/suspend-read-crc-pipe-B
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1480955258-26311-1-git-send-email-imre.deak@intel.com
Replace INTEL_ERR_OR_DBG_KMS macro with an intel_err_or_dbg_kms
function to shrink the code and rodata strings.
text data bss dec hex filename
1271480 41831 2016 1315327 1411ff i915.ko.0
1265160 41831 2016 1309007 13f94f i915.ko.2
Total of ~6 KiB saving across text and strings.
v2:
* Annotate the function for printf-style checking.
* Rename to pipe_config_err. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1481021420-5783-1-git-send-email-tvrtko.ursulin@linux.intel.com
first set of fixes for -next.
* tag 'drm-intel-next-fixes-2016-12-07' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Move priority bumping for flips earlier
drm/i915: Hold a reference on the request for its fence chain
drm/i915/audio: fix hdmi audio noise issue
drm/i915/debugfs: Increment return value of gt.next_seqno
drm/i915/debugfs: Drop i915_hws_info
drm/i915: Initialize dev_priv->atomic_cdclk_freq at init time
drm/i915: Fix cdclk vs. dev_cdclk mess when not recomputing things
drm/i915: Make skl_write_{plane,cursor}_wm() static
drm/i915: Complete requests in nop_submit_request
drm/i915/gvt: fix lock not released bug for dispatch_workload() err path
drm/i915/gvt: fix getting 64bit bar size error
drm/i915/gvt: fix missing init param.primary
Pineview deserves to use its own platform enum (which was already added,
unused, previously). IS_G33() no longer matches Pineview, and gets
replaced by IS_G33() || IS_PINEVIEW() or equivalent. Pineview is no
longer an outlier among platform definitions.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481143689-19672-1-git-send-email-jani.nikula@intel.com
As we use debugobjects to track the lifetime of fences within our atomic
state, we ideally want to mark those objects as freed along with their
containers. This merits us hookin into config->funcs->atomic_state_free
for this purpose.
This allows us to enable debugobjects for sw-fences without triggering
known issues.
Fixes: fc1584059d ("drm/i915: Integrate i915_sw_fence with debugobjects")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161205142941.21965-4-chris@chris-wilson.co.uk
Before we attempt to turn any planes on or off we must first exit
csxr. That's due to cxsr effectively making the plane enable bits
read-only. Currently we achieve that with a vblank wait right after
toggling the cxsr enable bit. We do the vblank wait even if cxsr was
already off, which seems wasteful, so let's try to only do it when
absolutely necessary.
We could start tracking the cxsr state fully somewhere, but for now
it seems easiest to just have intel_set_memory_cxsr() return the
previous cxsr state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480354637-14209-11-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Let's protect the cxsr state with the wm_mutex, since it might
get poked from multiple places if there's a parallel plane update
happening with a pipe getting enable/disabled.
It's still pretty racy for the old platforms, but for vlv/chv it
should work, I think. If not, we'll improve it later anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480354637-14209-10-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
ilk_disable_lp_wm() will tell us whether the LP1+ watermarks were
disabled or not, and hence whether we need to for the vblank wait or
not. Let's use that information to eliminate some useless vblank
waits.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480354637-14209-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
HSW+ all use the .initial_watermarks() hook, so there's no point in
calling intel_update_watermarks() from HSW+ specific code. We'll still
hang on to the .initial_watermarks NULL check since theoretically if the
memory latencies are not populated we would not populate the function
pointer either.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480354637-14209-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Looks like we're only initializing dev_priv->atomic_cdclk_freq
at resume and commit times, not at init time. Let's do that as
well.
We're now hitting the 'WARN_ON(intel_state->cdclk == 0)' in
hsw_compute_linetime_wm() on account of populating
intel_state->cdclk from dev_priv->atomic_cdclk_freq.
Previously we were mispopulating intel_state->cdclk with
dev_priv->cdclk_freq which always had a proper value at init
time and hence the WARN_ON() didn't trigger.
Cc: <stable@vger.kernel.org> # 4.6+: 14676ec6b1 drm/i915: Fix cdclk vs. dev_cdclk mess when not recomputing things
Cc: <stable@vger.kernel.org> # 4.6+
Cc: Matthew Auld <matthew.auld@intel.com>
Reported-by: Matthew Auld <matthew.auld@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98902
Fixes: 14676ec6b1 ("drm/i915: Fix cdclk vs. dev_cdclk mess when not recomputing things")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480428837-4207-1-git-send-email-ville.syrjala@linux.intel.com
Tested-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
(cherry picked from commit 6a259b1f8a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When we end up not recomputing the cdclk, we need to populate
intel_state->cdclk with the "atomic_cdclk_freq" instead of the
current cdclk_freq. When no pipes are active, the actual cdclk_freq
may be lower than what the configuration of the planes and
pipes would require from the point of view of the software state.
This fixes bogus WARNS from skl_max_scale() which is trying to check
the plane software state against the cdclk frequency. So any time
it got called during DPMS off for instance, we might have tripped
the warn if the current mode would have required a higher than
minimum cdclk.
v2: Drop the dev_cdclk stuff (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: bruno.pagani@ens-lyon.org
Cc: Daniel J Blueman <daniel.blueman@gmail.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Paul Bolle <pebolle@tiscali.nl>
Tested-by: Joseph Yasi <joe.yasi@gmail.com> (v1)
Cc: <stable@vger.kernel.org> # v4.6+
Fixes: 1a617b7765 ("drm/i915: Keep track of the cdclk as if all crtc's were active.")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98214
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479141311-11904-2-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit e0ca7a6be3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Resync, and we need all the fancy new drm_mm stuff to implement more
efficient evict algorithms for softpin.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYRIGyAAoJEHm+PkMAQRiG2ksH/jwMUT9j6glbwESxbn1YTqTM
QcBT5AMc7D0wNuidQe0hWZMtG4RbC+4ZhxzZl2wPgA2gueJ+rBnyX7bgtA7ka8ka
Fdc3u/Q1v38HPzf8iBnxcdCs40VgsoMLjFYCXrpOxuGDNKYzRd+Q8aI2TeGvzbyi
X8+6oAWifBwo2oA06jfcuUncEWbyDDyK9aQksmfKOpjHdb26yELPEhsPOlds1g7E
jYLnvUVnU2CoFaumta+rZQ0kzLdc4Ntu0wEao6WzJuQKsgoID+tS/6iudi8cUhDp
YowGAVoOfr6rAJB0mwrDVfugpamaT3386XKyocdNsK0/jR60UIJ8x+WzvvSU+lY=
=JTBj
-----END PGP SIGNATURE-----
Backmerge tag 'v4.9-rc8' into drm-next
Linux 4.9-rc8
Daniel requested this so we could apply some follow on fixes cleanly to -next.
Geminilake has the same register layout, reference clock and programming
sequence as broxton. The difference is that it doesn't support the 1.5
divider and has different ratios, but a lot of code can be shared
between the two platforms.
v2: Rebase (s/broxton/bxt).
v3: Fix vco calculation in glk_de_pll_vco().
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480667037-11215-7-git-send-email-ander.conselvan.de.oliveira@intel.com
Geminilake is mostly backwards compatible with broxton, so change most
of the IS_BROXTON() checks to IS_GEN9_LP(). Differences between the
platforms will be implemented in follow-up patches.
v2: Don't reuse broxton's path in intel_update_max_cdclk().
Don't set plane count as in broxton.
v3: Rebase
v4: Include the check intel_bios_is_port_hpd_inverted().
Commit message.
v5: Leave i915_dmc_info() out; glk's csr version != bxt's. (Rodrigo)
v6: Rebase.
v7: Convert a few mode IS_BROXTON() occurances in pps, ddi, dsi and pll
code. (Rodrigo)
v8: Squash a couple of DDI patches with more conversions. (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480667037-11215-2-git-send-email-ander.conselvan.de.oliveira@intel.com
Simplify the code by passing the right argument in.
v2: Commit message. (Joonas Lahtinen)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Makes all GEM object constructors consistent.
v2: Fix compilation in GVT code.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v1)
Where it is more appropriate and also to be consistent with
the direction of the driver.
v2: Leave out object alloc/free inlining. (Joonas Lahtinen)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We grab the struct_mutex in intel_crtc_page_flip, but if we are wedged
or a reset is in progress we bail early but never seem to actually
release the lock.
Fixes: 7f1847ebf4 ("drm/i915: Simplify checking of GPU reset_counter in display pageflips")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161128103648.9235-1-matthew.auld@intel.com
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v4.7+
(cherry picked from commit ddbb271aea)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Big thing is that drm-misc is now officially a group maintainer/committer
model thing, with MAINTAINERS suitably updated. Otherwise just the usual
pile of misc things all over, nothing that stands out this time around.
* tag 'drm-misc-next-2016-11-29' of git://anongit.freedesktop.org/git/drm-misc: (33 commits)
drm: Introduce drm_framebuffer_assign()
drm/bridge: adv7511: Enable the audio data and clock pads on adv7533
drm/bridge: adv7511: Add Audio support
drm/edid: Consider alternate cea timings to be the same VIC
drm/atomic: Constify drm_atomic_crtc_needs_modeset()
drm: bridge: dw-hdmi: add ASoC dependency
drm: Fix shift operations for drm_fb_helper::drm_target_preferred()
drm: Avoid NULL dereference for DRM_LEGACY debug message
drm: Use u64_to_user_ptr() helper for blob ioctls
drm: Fix conflicting macro parameter in drm_mm_for_each_node_in_range()
drm: Fixup kernel doc for driver->gem_create_object
drm/hisilicon/hibmc: mark PM functions __maybe_unused
drm/hisilicon/hibmc: Checking for NULL instead of IS_ERR()
drm: bridge: add DesignWare HDMI I2S audio support
drm: Check against color expansion in drm_mm_reserve_node()
drm: Define drm_mm_for_each_node_in_range()
drm/doc: Fix links in drm_property.c
MAINTAINERS: Add link to drm-misc documentation
vgaarb: use valid dev pointer in vgaarb_info()
drm/atomic: Unconfuse the old_state mess in commmit_tail
...
Looks like we're only initializing dev_priv->atomic_cdclk_freq
at resume and commit times, not at init time. Let's do that as
well.
We're now hitting the 'WARN_ON(intel_state->cdclk == 0)' in
hsw_compute_linetime_wm() on account of populating
intel_state->cdclk from dev_priv->atomic_cdclk_freq.
Previously we were mispopulating intel_state->cdclk with
dev_priv->cdclk_freq which always had a proper value at init
time and hence the WARN_ON() didn't trigger.
Cc: stable@vger.kernel.org
Cc: Matthew Auld <matthew.auld@intel.com>
Reported-by: Matthew Auld <matthew.auld@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98902
Fixes: e0ca7a6be3 ("drm/i915: Fix cdclk vs. dev_cdclk mess when not recomputing things")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480428837-4207-1-git-send-email-ville.syrjala@linux.intel.com
Tested-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
99% of the time we access i915_address_space->dev we want the i915
device and not the drm device, so let's store the drm_i915_private
backpointer instead. The only real complication here are the inlines
in i915_vma.h where drm_i915_private is not yet defined and so we have
to choose an alternate path for our asserts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161129095008.32622-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We grab the struct_mutex in intel_crtc_page_flip, but if we are wedged
or a reset is in progress we bail early but never seem to actually
release the lock.
Fixes: 7f1847ebf4 ("drm/i915: Simplify checking of GPU reset_counter in display pageflips")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161128103648.9235-1-matthew.auld@intel.com
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v4.7+
Pass dev_priv to intel_setup_outputs() and functions called by it, since
those are all intel i915 specific functions. Also, in the majority of
the functions dev_priv is used more often than dev. In the rare cases
where there are a few calls back into drm core, a local dev variable was
added.
v2: Don't convert dev to &dev_priv->drm in intel_dsi_init. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479910904-11005-1-git-send-email-ander.conselvan.de.oliveira@intel.com
A modeset on one pipe can update dev_priv->atomic_cdclk_freq without
actually touching the hardware, in which case we won't force a modeset
on all the pipes, and thus won't lock any of the other pipes either.
That means a parallel plane update on another pipe could be looking at
a stale dev_priv->atomic_cdcdlk_freq and thus fail to notice when the
plane configuration is invalid, or potentially reject a valid update.
To overcome this we must protect writes to atomic_cdclk_freq with
all the crtc locks, and thus for reads any single crtc lock will
be sufficient protection.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479141311-11904-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we end up not recomputing the cdclk, we need to populate
intel_state->cdclk with the "atomic_cdclk_freq" instead of the
current cdclk_freq. When no pipes are active, the actual cdclk_freq
may be lower than what the configuration of the planes and
pipes would require from the point of view of the software state.
This fixes bogus WARNS from skl_max_scale() which is trying to check
the plane software state against the cdclk frequency. So any time
it got called during DPMS off for instance, we might have tripped
the warn if the current mode would have required a higher than
minimum cdclk.
v2: Drop the dev_cdclk stuff (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: bruno.pagani@ens-lyon.org
Cc: Daniel J Blueman <daniel.blueman@gmail.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Paul Bolle <pebolle@tiscali.nl>
Tested-by: Joseph Yasi <joe.yasi@gmail.com> (v1)
Cc: stable@vger.kernel.org
Fixes: 1a617b7765 ("drm/i915: Keep track of the cdclk as if all crtc's were active.")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98214
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479141311-11904-2-git-send-email-ville.syrjala@linux.intel.com
Use intel_plane->id to derive the VLV/CHV sprite register offsets
instead of abusing plane->plane which is really meant to for
primary planes only.
v2: Convert assert_sprites_disabled() over as well
v3: Rename the reg macro parameter to 'plane_id' as well (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-6-git-send-email-ville.syrjala@linux.intel.com
Replace the intel_plane->plane and hardcoded 0 usage in the SKL plane
code with intel_plane->id.
This should make the SKL "primary" and "sprite" code virtually
identical, so the next logical step would likely be dropping one
of the copies.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-5-git-send-email-ville.syrjala@linux.intel.com
Add a mask of which planes are available for each pipe. This doesn't
quite work for old platforms with dynamic plane<->pipe assignment, but
as we don't support that sort of stuff (yet) we can get away with it.
The main use I have for this is the for_each_plane_id_on_crtc() macro
for iterating over all possible planes on the crtc. I suppose we could
not add the mask, and instead iterate by comparing intel_plane->pipe
but then we'd need a local intel_plane variable which is just
unnecessary clutter in some cases. But I'm not hung up on this, so if
people prefer the other option I could be convinced to use it.
v2: Use BIT() in the iterator macro too (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-3-git-send-email-ville.syrjala@linux.intel.com
As I told people in [1] we really should not be confusing enum plane
as a per-pipe plane identifier. Looks like that happened nonetheless, so
let's fix it up by splitting the two into two enums.
We'll also want something we just directly pass to various register
offset macros and whatnot on SKL+. So let's make this new thing work for that.
Currently we pass intel_plane->plane for the "sprites" and just a
hardcoded zero for the "primary" planes. We want to get rid of that
hardocoding so that we can share the same code for all planes (apart
from the legacy cursor of course).
[1] https://lists.freedesktop.org/archives/intel-gfx/2015-September/076082.html
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-2-git-send-email-ville.syrjala@linux.intel.com
Currently we only clflush the scanout if it is in the CPU domain. Also
flush if we have a pending CPU clflush. We also want to treat the
dirtyfb path similar, and flush any pending writes there as well.
v2: Only send the fb flush message if flushing the dirt on flip
v3: Make flush-for-flip and dirtyfb look more alike since they serve
similar roles as end-of-frame marker.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> #v2
Link: http://patchwork.freedesktop.org/patch/msgid/20161118211747.25197-1-chris@chris-wilson.co.uk
Kernel pointer does not sound like an useful thing to log and
pipe name is already contained in the crtc name.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
It looks to me skl_update_scaler will already log interesting
debug messages when the state transitions or there is an error.
In this case it feels we can remove the two unconditional
debug messages which happen immediately before calling
skl_update_scaler. This way we get rid of the sole debug
message when switching virtual terminals for example.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479376805-5087-1-git-send-email-tvrtko.ursulin@linux.intel.com
And as usual a little bit of cascaded function prototype changes.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
And a little bit of function prototype changes.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
And a little bit of cascaded function prototype changes.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tvrtko needs
commit b3c11ac267
Author: Eric Engestrom <eric@engestrom.ch>
Date: Sat Nov 12 01:12:56 2016 +0000
drm: move allocation out of drm_get_format_name()
to be able to apply his patches without conflicts.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It has been suggested that having per-plane modifiers is making life
more difficult for userspace, so let's just retire modifier[1-3] and
use modifier[0] to apply to the entire framebuffer.
Obviosuly this means that if individual planes need different tiling
layouts and whatnot we will need a new modifier for each combination
of planes with different tiling layouts.
For a bit of extra backwards compatilbilty the kernel will allow
non-zero modifier[1+] but it require that they will match modifier[0].
This in case there's existing userspace out there that sets
modifier[1+] to something non-zero with planar formats.
Mostly a cocci job, with a bit of manual stuff mixed in.
@@
struct drm_framebuffer *fb;
expression E;
@@
- fb->modifier[E]
+ fb->modifier
@@
struct drm_framebuffer fb;
expression E;
@@
- fb.modifier[E]
+ fb.modifier
Cc: Kristian Høgsberg <hoegsberg@gmail.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tomeu Vizoso <tomeu@tomeuvizoso.net>
Cc: dczaplejewicz@collabora.co.uk
Suggested-by: Kristian Høgsberg <hoegsberg@gmail.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1479295996-26246-1-git-send-email-ville.syrjala@linux.intel.com
dev_priv->hw_ddb is only used by skl_update_crtcs, but the ddb
allocation for each pipe is calculated in crtc_state.
We can rid of the global member by looking at crtc_state.
Do this by saving all active old ddb allocations from the old crtc_state
in an array, and then point them to the new allocation every time we update
a crtc.
This will allow us to keep track of the intermediate ddb allocations,
which is what hw_ddb was previously used for. With hw_ddb gone all
SKL-style watermark values are properly maintained only in crtc_state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478609742-13603-5-git-send-email-maarten.lankhorst@linux.intel.com
[mlankhorst: Reword commit message.]
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
This is the last bit required for making nonblocking modesets work
correctly. The state in intel_crtc->hw_ddb is updated in the
nonblocking part of a nonblocking commit.
This means that even attempting a commit before a nonblocking modeset
completes will fail, because intel_crtc->hw_ddb still has stale values.
The stale values are 0 if the crtc is being enabled resulting in a
failure during atomic check, but it may also result in double use of
ddb allocations.
Fix this by explicitly copying the ddb allocation from the old state.
This has to be done explicitly, because a modeset that doesn't change
active pipes, or a modeset converted to a fastset will will clear the
current state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478609742-13603-4-git-send-email-maarten.lankhorst@linux.intel.com
[mlankhorst: Reword commit message.]
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
The watermark updates for SKL style watermarks are no longer done
in the plane callbacks, but are now called in a separate watermark
update function that's called during the same vblank evasion,
before the plane updates.
This also gets rid of the global skl_results, which was required for
keeping track of the current atomic commit.
Changes since v1:
- Move line unwrap to correct patch. (Lyude)
- Make sure we don't regress ILK watermarks. (Matt)
- Rephrase commit message. (Matt)
Changes since v2:
- Fix disable watermark check to use the correct way to determine single
step watermark support.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lyude <cpaul@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478609742-13603-3-git-send-email-maarten.lankhorst@linux.intel.com
[mlankhorst: Small whitespace fix in skl_initial_wm]
Allow the driver to write watermarks during atomic evasion.
This will make it possible to write the watermarks in a cleaner
way on gen9+.
intel_atomic_state is not used here yet, but will be used when
we program all watermarks as a separate step during evasion.
This also writes linetime all the time, while before it was only
done during plane updates. This looks like this could be a bugfix,
but I'm not sure what it affects.
Changes since v1:
- Add comment about atomic evasion to commit message.
- Unwrap I915_WRITE call. (Lyude)
Changes since v2:
- Rename atomic_evade_watermarks to atomic_update_watermarks. (Ville)
- Add line wraps where appropriate, fix grammar in commit message. (Matt)
Changes since v3:
- Actually fix commit message. (Matt)
- Line wrap calls to watermark update functions. (Matt)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478609742-13603-2-git-send-email-maarten.lankhorst@linux.intel.com
Commit 6b5e90f58c ("drm/i915/scheduler: Boost priorities for flips")
added priority boosting for the modern atomic pageflips (and modesets),
but we should do the same for existing users of mmioflips (we don't yet
need to consider csflips as they are not used by execlists and so do not
have any support for a scheduler).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20161115092249.18356-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Boost the priority of any rendering required to show the next pageflip
as we want to avoid missing the vblank by being delayed by invisible
workload. We prioritise avoiding jank and jitter in the GUI over
starving background tasks.
v2: Descend dma_fence_array when boosting priorities.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161114204105.29171-10-chris@chris-wilson.co.uk
On pre-gen4 we connect plane A to pipe B and vice versa to get an FBC
capable plane feeding the LVDS port by default. We have the logic for
the plane swapping duplicated in many places. Let's remove a bit of the
duplication by having the crtc look up the thing from the primary plane.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478616439-10150-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The primary and sprite planes on CHV pipe B support horizontal
mirroring. Expose it to the world.
Sadly the hardware ignores the mirror bit when the rotate bit is
set, so we'll have to reject the 180+X case.
v2: Drop the BIT()
v3: Pass dev_priv instead of dev to IS_CHERRYVIEW()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479142440-25283-4-git-send-email-ville.syrjala@linux.intel.com
Move the plane control register rotation setup away from the
coordinate munging code. This will result in neater looking
code once we add reflection support for CHV.
v2: Drop the BIT(), drop some usless parens,
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479142440-25283-3-git-send-email-ville.syrjala@linux.intel.com
Using == to check for 180 degree rotation only works as long as the
reflection bits aren't set. That will change soon enough for CHV, so
let's stop doing things the wrong way.
v2: Drop the BIT()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479142440-25283-2-git-send-email-ville.syrjala@linux.intel.com
The function's behaviour was changed in 90844f0004, without changing
its signature, causing people to keep using it the old way without
realising they were now leaking memory.
Rob Clark also noticed it was also allocating GFP_KERNEL memory in
atomic contexts, breaking them.
Instead of having to allocate GFP_ATOMIC memory and fixing the callers
to make them cleanup the memory afterwards, let's change the function's
signature by having the caller take care of the memory and passing it to
the function.
The new parameter is a single-field struct in order to enforce the size
of its buffer and help callers to correctly manage their memory.
Fixes: 90844f0004 ("drm: make drm_get_format_name thread-safe")
Cc: Rob Clark <robdclark@gmail.com>
Cc: Christian König <christian.koenig@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Sinclair Yeh <syeh@vmware.com> (vmwgfx)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Eric Engestrom <eric@engestrom.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161112011309.9799-1-eric@engestrom.ch
After this patch only conversion of INTEL_INFO(p)->gen to
INTEL_GEN(dev_priv) remains before the __I915__ macro can
be removed.
v2: Tidy vlv_compute_wm. (David Weinehall)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
A small selection of macros which can only accept dev_priv from
now on and a resulting trickle of fixups.
v2: Keep original order. (Ville Syrjala)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
- better atomic state debugging from Rob
- fence prep from gustavo
- sumits flushed out his backlog of pending dma-buf/fence patches from
various people
- drm_mm leak debugging plus trying to appease Kconfig (Chris)
- a few misc things all over
* tag 'topic/drm-misc-2016-11-10' of git://anongit.freedesktop.org/drm-intel: (35 commits)
drm: Make DRM_DEBUG_MM depend on STACKTRACE_SUPPORT
drm/i915: Restrict DRM_DEBUG_MM automatic selection
drm: Restrict stackdepot usage to builtin drm.ko
drm/msm: module param to dump state on error irq
drm/msm/mdp5: add atomic_print_state support
drm/atomic: add debugfs file to dump out atomic state
drm/atomic: add new drm_debug bit to dump atomic state
drm: add helpers to go from plane state to drm_rect
drm: add helper for printing to log or seq_file
drm: helper macros to print composite types
reservation: revert "wait only with non-zero timeout specified (v3)" v2
drm/ttm: fix ttm_bo_wait
dma-buf/fence: revert "don't wait when specified timeout is zero" (v2)
dma-buf/fence: make timeout handling in fence_default_wait consistent (v2)
drm/amdgpu: add the interface of waiting multiple fences (v4)
dma-buf: return index of the first signaled fence (v2)
MAINTAINERS: update Sync File Framework files
dma-buf/sw_sync: put fence reference from the fence creation
dma-buf/sw_sync: mark sync_timeline_create() static
drm: Add stackdepot include for DRM_DEBUG_MM
...
All of this state should be updated as soon as possible. It shouldn't be
done later because then future updates may not depend on it.
Changes since v1:
- Move the modeset update to before drm_atomic_state_get. (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478609742-13603-10-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
[seanpaul resolved conflict in drm_plane.h]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The code to determine the primary plane offset for gen2/3 looks
different than the code for gen4+, but in fact it's doing the same
thing. Let's make it uniform. Allows us to eliminate the 'obj' from
the list of local variables as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478550057-24864-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
According to BSpec, cdclk for BDW has to be not less than 432 MHz with DP
audio enabled, port width x4, and link rate HBR2 (5.4 GHz). With cdclk less
than 432 MHz, enabling audio leads to pipe FIFO underruns and displays
cycling on/off.
Let's apply this work around to GEN9 platforms too, as it fixes the same
issue.
v2: Move drm_device to drm_i915_private conversion
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97907
Cc: stable@vger.kernel.org
Cc: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478117601-19122-1-git-send-email-dhinakaran.pandiyan@intel.com
(cherry picked from commit 9c75402418)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
According to BSpec, cdclk for BDW has to be not less than 432 MHz with DP
audio enabled, port width x4, and link rate HBR2 (5.4 GHz). With cdclk less
than 432 MHz, enabling audio leads to pipe FIFO underruns and displays
cycling on/off.
From BSpec:
"Display» BDW-SKL» dpr» [Register] DP_TP_CTL [BDW+,EXCLUDE(CHV)]
Workaround : Do not use DisplayPort with CDCLK less than 432 MHz, audio
enabled, port width x4, and link rate HBR2 (5.4 GHz), or else there may
be audio corruption or screen corruption."
Since, some DP configurations (e.g., MST) use port width x4 and HBR2
link rate, let's increase the cdclk to >= 432 MHz to enable audio for those
cases.
v4: Changed commit message
v3: Combine BDW pixel rate adjustments into a function (Jani)
v2: Restrict fix to BDW
Retain the set cdclk across modesets (Ville)
Cc: stable@vger.kernel.org
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478026080-2925-1-git-send-email-dhinakaran.pandiyan@intel.com
(cherry picked from commit b30ce9e055)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
According to BSpec, cdclk for BDW has to be not less than 432 MHz with DP
audio enabled, port width x4, and link rate HBR2 (5.4 GHz). With cdclk less
than 432 MHz, enabling audio leads to pipe FIFO underruns and displays
cycling on/off.
Let's apply this work around to GEN9 platforms too, as it fixes the same
issue.
v2: Move drm_device to drm_i915_private conversion
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97907
Cc: stable@vger.kernel.org
Cc: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478117601-19122-1-git-send-email-dhinakaran.pandiyan@intel.com
According to BSpec, cdclk for BDW has to be not less than 432 MHz with DP
audio enabled, port width x4, and link rate HBR2 (5.4 GHz). With cdclk less
than 432 MHz, enabling audio leads to pipe FIFO underruns and displays
cycling on/off.
From BSpec:
"Display» BDW-SKL» dpr» [Register] DP_TP_CTL [BDW+,EXCLUDE(CHV)]
Workaround : Do not use DisplayPort with CDCLK less than 432 MHz, audio
enabled, port width x4, and link rate HBR2 (5.4 GHz), or else there may
be audio corruption or screen corruption."
Since, some DP configurations (e.g., MST) use port width x4 and HBR2
link rate, let's increase the cdclk to >= 432 MHz to enable audio for those
cases.
v4: Changed commit message
v3: Combine BDW pixel rate adjustments into a function (Jani)
v2: Restrict fix to BDW
Retain the set cdclk across modesets (Ville)
Cc: stable@vger.kernel.org
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478026080-2925-1-git-send-email-dhinakaran.pandiyan@intel.com
Replace the open coded dev_priv->pipe_to_crtc_mapping[] usage with
intel_get_crtc_for_pipe().
Mostly done with coccinelle, with a few manual tweaks
@@
expression E1, E2;
@@
(
- E1->pipe_to_crtc_mapping[E2]
+ intel_get_crtc_for_pipe(E1, E2)
|
- E1->plane_to_crtc_mapping[E2]
+ intel_get_crtc_for_plane(E1, E2)
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477946245-14134-12-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
There's no need to keep a duplicate skl_pipe_wm around any more,
everything can be discovered from crtc_state, which we pass around
correctly now even in case of plane disable.
The copy in intel_crtc->wm.skl.active is equal to
crtc_state->wm.skl.optimal after the atomic commit completes.
It's useful for two-step watermark programming, but not required for
gen9+ which does it in a single step. We can pull the old allocation
from old_crtc_state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477489299-25777-9-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Due to the plane->index not getting readjusted in drm_plane_cleanup(),
we can't continue initialization of some plane/crtc init fails.
Well, we sort of could I suppose if we left all initialized planes on
the list, but that would expose those planes to userspace as well.
But for crtcs the situation is even worse since we assume that
pipe==crtc index occasionally, so we can't really deal with a partially
initialize set of crtcs.
So seems safest to just abort the entire thing if anything goes wrong.
All the failure paths here are kmalloc()s anyway, so it seems unlikely
we'd get very far if these start failing.
v2: Add (enum plane) case to silence gcc
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477411083-19255-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After combining the dma-buf reservation object and the GEM reservation
object, we lost the ability to do a nonblocking wait on the i915 request
(as we blocked upon the reservation object during prepare_fb). We can
instead convert the reservation object into a fence upon which we can
asynchronously wait (including a forced timeout in case the DMA fence is
never signaled).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161028125858.23563-22-chris@chris-wilson.co.uk
In preparation to support many distinct timelines, we need to expand the
activity tracking on the GEM object to handle more than just a request
per engine. We already use the struct reservation_object on the dma-buf
to handle many fence contexts, so integrating that into the GEM object
itself is the preferred solution. (For example, we can now share the same
reservation_object between every consumer/producer using this buffer and
skip the manual import/export via dma-buf.)
v2: Reimplement busy-ioctl (by walking the reservation object), postpone
the ABI change for another day. Similarly use the reservation object to
find the last_write request (if active and from i915) for choosing
display CS flips.
Caveats:
* busy-ioctl: busy-ioctl only reports on the native fences, it will not
warn of stalls (in set-domain-ioctl, pread/pwrite etc) if the object is
being rendered to by external fences. It also will not report the same
busy state as wait-ioctl (or polling on the dma-buf) in the same
circumstances. On the plus side, it does retain reporting of which
*i915* engines are engaged with this object.
* non-blocking atomic modesets take a step backwards as the wait for
render completion blocks the ioctl. This is fixed in a subsequent
patch to use a fence instead for awaiting on the rendering, see
"drm/i915: Restore nonblocking awaits for modesetting"
* dynamic array manipulation for shared-fences in reservation is slower
than the previous lockless static assignment (e.g. gem_exec_lut_handle
runtime on ivb goes from 42s to 66s), mainly due to atomic operations
(maintaining the fence refcounts).
* loss of object-level retirement callbacks, emulated by VMA retirement
tracking.
* minor loss of object-level last activity information from debugfs,
could be replaced with per-vma information if desired
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161028125858.23563-21-chris@chris-wilson.co.uk
Having moved the locked phase of freeing an object to a separate worker,
we can now declare to the core that we only need the unlocked variant of
driver->gem_free_object, and can use the simple unreference internally.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161028125858.23563-20-chris@chris-wilson.co.uk
Our low-level wait routine has evolved from our generic wait interface
that handled unlocked, RPS boosting, waits with time tracking. If we
push our GEM fence tracking to use reservation_objects (required for
handling multiple timelines), we lose the ability to pass the required
information down to i915_wait_request(). However, if we push the extra
functionality from i915_wait_request() to the individual callsites
(i915_gem_object_wait_rendering and i915_gem_wait_ioctl) that make use
of those extras, we can both simplify our low level wait and prepare for
extending the GEM interface for use of reservation_objects.
v2: Rewrite i915_wait_request() kerneldocs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161028125858.23563-4-chris@chris-wilson.co.uk
This macro's name is a bit misleading; it doesn't actually iterate over
all planes since it omits the cursor plane. Its only uses are in gen9
code which is using it to iterate over the universal planes (which we
treat as primary+sprites); in these cases the legacy cursor registers
are programmed independently if necessary. The macro's iterator value
(0 for primary plane, spritenum+1 for each secondary plane) also isn't
meaningful outside the gen9 context where the hardware considers them to
all be "universal" planes that follow this numbering.
This is just a renaming/clarification patch with no functional change.
However it will make the subsequent patches more clear.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477522291-10874-2-git-send-email-matthew.d.roper@intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Pass the framebuffer size in .16 fixed point coordinates to
drm_rect_rotate() since that's what the source coordinates are as well
at this stage. We used to do this part of the computation in integer
coordinates, but that got changed when moving the computation to
happen in the check phase of the operation. Unfortunately I forgot
to shift up the fb width and height appropriately.
With the bogus size we ended up with some negative fb offset, which when
added to the vma offset caused out scanout to start at an offset earlier
than we inteded. Eg. when testing on my SKL I saw a row of incorrect
tiles at the top of my screen.
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477325584-23679-1-git-send-email-ville.syrjala@linux.intel.com
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit da064b47c0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The previous code would wait for fences on the framebuffer from the old
plane state to complete, rather than the new, so you would see tearing
everywhere. Fix this to wait on the new state before we make it active.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Fixes: 94f050246b ("drm/i915: nonblocking commit")
Cc: stable@vger.kernel.org
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161021144454.6288-1-daniels@collabora.com
(cherry picked from commit 2d2c5ad83f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Pass the framebuffer size in .16 fixed point coordinates to
drm_rect_rotate() since that's what the source coordinates are as well
at this stage. We used to do this part of the computation in integer
coordinates, but that got changed when moving the computation to
happen in the check phase of the operation. Unfortunately I forgot
to shift up the fb width and height appropriately.
With the bogus size we ended up with some negative fb offset, which when
added to the vma offset caused out scanout to start at an offset earlier
than we inteded. Eg. when testing on my SKL I saw a row of incorrect
tiles at the top of my screen.
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477325584-23679-1-git-send-email-ville.syrjala@linux.intel.com
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Backmerge because Chris Wilson needs the very latest&greates of
Gustavo Padovan's sync_file work, specifically the refcounting changes
from:
commit 30cd85dd6e
Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Date: Wed Oct 19 15:48:32 2016 -0200
dma-buf/sync_file: hold reference to fence when creating sync_file
Also good to sync in general since git tends to get confused with the
cherry-picking going on.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
- first slice of the gvt device model (Zhenyu et al)
- compression support for gpu error states (Chris)
- sunset clause on gpu errors resulting in dmesg noise telling users
how to report them
- .rodata diet from Tvrtko
- switch over lots of macros to only take dev_priv (Tvrtko)
- underrun suppression for dp link training (Ville)
- lspcon (hmdi 2.0 on skl/bxt) support from Shashank Sharma, polish
from Jani
- gen9 wm fixes from Paulo&Lyude
- updated ddi programming for kbl (Rodrigo)
- respect alternate aux/ddc pins (from vbt) for all ddi ports (Ville)
* tag 'drm-intel-next-2016-10-24' of git://anongit.freedesktop.org/drm-intel: (227 commits)
drm/i915: Update DRIVER_DATE to 20161024
drm/i915: Stop setting SNB min-freq-table 0 on powersave setup
drm/i915/dp: add lane_count check in intel_dp_check_link_status
drm/i915: Fix whitespace issues
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_ddc_pin for all DDI ports
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: Remove WaEnableYV12BugFixInHalfSliceChicken7
drm/i915: KBL - Recommended buffer translation programming for DisplayPort
drm/i915: Move down skl/kbl ddi iboost and n_edp_entires fixup
drm/i915: Add a sunset clause to GPU hang logging
drm/i915: Stop reporting error details in dmesg as well as the error-state
drm/i915/gvt: do not ignore return value of create_scratch_page
drm/i915/gvt: fix spare warnings on odd constant _Bool cast
drm/i915/gvt: mark symbols static where possible
drm/i915/gvt: fix sparse warnings on different address spaces
drm/i915/gvt: properly access enabled intel_engine_cs
drm/i915/gvt: Remove defunct vmap_batch()
drm/i915/gvt: Use common mapping routines for shadow_bb object
drm/i915/gvt: Use common mapping routines for indirect_ctx object
...
First -misc pull for 4.10:
- drm_format rework from Laurent
- reservation patches from Chris that missed 4.9.
- aspect ratio support in infoframe helpers and drm mode/edid code
(Shashank Sharma)
- rotation rework from Ville (first parts at least)
- another attempt at the CRC debugfs interface from Tomeu
- piles and piles of misc patches all over
* tag 'topic/drm-misc-2016-10-24' of git://anongit.freedesktop.org/drm-intel: (55 commits)
drm: Use u64 for intermediate dotclock calculations
drm/i915: Use the per-plane rotation property
drm/omap: Use per-plane rotation property
drm/omap: Set rotation property initial value to BIT(DRM_ROTATE_0) insted of 0
drm/atmel-hlcdc: Use per-plane rotation property
drm/arm: Use per-plane rotation property
drm: Add support for optional per-plane rotation property
drm/atomic: Reject attempts to use multiple rotation angles at once
drm: Add drm_rotation_90_or_270()
dma-buf/sync_file: hold reference to fence when creating sync_file
drm/virtio: kconfig: Fixup white space.
drm/fence: release fence reference when canceling event
drm/i915: Handle early failure during intel_get_load_detect_pipe
drm/fb_cma_helper: do not free fbdev if there is none
drm: fix sparse warnings on undeclared symbols in crc debugfs
gpu: Remove depends on RESET_CONTROLLER when not a provider
i915: don't call drm_atomic_state_put on invalid pointer
drm: Don't export the drm_fb_get_bpp_depth() function
drm/arm: mali-dp: Replace drm_fb_get_bpp_depth() with drm_format_plane_cpp()
drm: vmwgfx: Replace drm_fb_get_bpp_depth() with drm_format_info()
...
The previous code would wait for fences on the framebuffer from the old
plane state to complete, rather than the new, so you would see tearing
everywhere. Fix this to wait on the new state before we make it active.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Fixes: 94f050246b ("drm/i915: nonblocking commit")
Cc: stable@vger.kernel.org
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161021144454.6288-1-daniels@collabora.com
On certain platforms not all planes support the same set of
rotations/reflections, so let's use the per-plane property
for this.
This is already a problem on SKL when we use the legay cursor plane
as it only supports 0|180 whereas the universal planes support
0|90|180|270, and it will be a problem on CHV soon.
v2: Use drm_plane_create_rotation_property() helper
v3: Drop the BIT(), use INTEL_GEN()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1474907460-10717-12-git-send-email-ville.syrjala@linux.intel.com
We have intel_rotation_90_or_270() in i915 to check if the rotation is
90 or 270 degrees. Similar checks are elsewhere in drm, so let's move
the helper into a central place and use it everwhere.
v2: Drop the BIT()
Convert all new intel_rotation_90_or_270() calls
Deal with superfluous code shuffling
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1474907460-10717-2-git-send-email-ville.syrjala@linux.intel.com
Wrapping strings is against the guidelines in Documentation/CodingStyle,
chapter 2.
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476480722-13015-11-git-send-email-cpaul@redhat.com
Thanks to Paulo Zanoni for indirectly pointing this out.
Looks like we never actually added any code for checking whether or not
we actually wrote watermark levels properly. Let's fix that.
Changes since v1:
- Use %u instead of %d when printing WM state mismatches
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476480722-13015-10-git-send-email-cpaul@redhat.com
Now that we've make skl_wm_levels make a little more sense, we can
remove all of the redundant wm information. Up until now we'd been
storing two copies of all of the skl watermarks: one being the
skl_pipe_wm structs, the other being the global wm struct in
drm_i915_private containing the raw register values. This is confusing
and problematic, since it means we're prone to accidentally letting the
two copies go out of sync. So, get rid of all of the functions
responsible for computing the register values and just use a single
helper, skl_write_wm_level(), to convert and write the new watermarks on
the fly.
Changes since v1:
- Fixup skl_write_wm_level()
- Fixup skl_wm_level_from_reg_val()
- Don't forget to copy *active to intel_crtc->wm.active.skl
Changes since v2:
- Fix usage of wrong cstate
Changes since v3 (by Paulo):
- Rebase
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v2)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476814189-6062-1-git-send-email-paulo.r.zanoni@intel.com
The introduction of reference counting on the state structures caused
sanitize_watermarks() in i915 to break in the error handling case,
as pointed out by gcc -Wmaybe-uninitialized
drivers/gpu/drm/i915/intel_display.c: In function ‘intel_modeset_init’:
include/drm/drm_atomic.h:224:2: error: ‘state’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This changes the function back to only drop the reference count
when it was successfully allocated first.
Fixes: 0853695c3b ("drm: Add reference counting to drm_atomic_state")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161018151652.2690201-1-arnd@arndb.de
drm_atomic_state has a complicated single owner model that tracks the
single reference from allocation through to destruction on another
thread - or perhaps on a local error path. We can simplify this tracking
by using reference counting (at a cost of a few more atomics). This is
even more beneficial when the lifetime of the state becomes more
convoluted than being passed to a single worker thread for the commit.
v2: Double check !intel atomic_commit functions for missing gets
v3: Update kerneldocs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161014121833.439-27-chris@chris-wilson.co.uk
Next part of cleaning up the watermark code for skl. This is easy, since
it seems that we never actually needed to keep track of the linetime in
the skl_wm_values struct anyway.
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
First part of cleaning up all of the skl watermark code. This moves the
structures for storing the ddb allocations of each pipe into
intel_crtc_state, along with moving the structures for storing the
current ddb allocations active on hardware into intel_crtc.
Changes since v1:
- Don't replace alloc->start = alloc->end = 0;
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Saves 944 bytes of .rodata strings and 128 bytes of .text.
v2: Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Saves 864 bytes of .rodata strings and ~100 of .text.
v2: Add parantheses around dev_priv. (Ville Syrjala)
v3: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Saves 1392 bytes of .rodata strings.
Also change a few function/macro prototypes in i915_gem_gtt.c
from dev to dev_priv where it made more sense to do so.
v2: Add parantheses around dev_priv. (Ville Syrjala)
v3: Mention function prototype changes. (David Weinehall)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
This saves 3248 bytes of .rodata strings.
v2: Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
With the possibility of addition of many more number of rings in future,
the drm_i915_private structure could bloat as an array, of type
intel_engine_cs, is embedded inside it.
struct intel_engine_cs engine[I915_NUM_ENGINES];
Though this is still fine as generally there is only a single instance of
drm_i915_private structure used, but not all of the possible rings would be
enabled or active on most of the platforms. Some memory can be saved by
allocating intel_engine_cs structure only for the enabled/active engines.
Currently the engine/ring ID is kept static and dev_priv->engine[] is simply
indexed using the enums defined in intel_engine_id.
To save memory and continue using the static engine/ring IDs, 'engine' is
defined as an array of pointers.
struct intel_engine_cs *engine[I915_NUM_ENGINES];
dev_priv->engine[engine_ID] will be NULL for disabled engine instances.
There is a text size reduction of 928 bytes, from 1028200 to 1027272, for
i915.o file (but for i915.ko file text size remain same as 1193131 bytes).
v2:
- Remove the engine iterator field added in drm_i915_private structure,
instead pass a local iterator variable to the for_each_engine**
macros. (Chris)
- Do away with intel_engine_initialized() and instead directly use the
NULL pointer check on engine pointer. (Chris)
v3:
- Remove for_each_engine_id() macro, as the updated macro for_each_engine()
can be used in place of it. (Chris)
- Protect the access to Render engine Fault register with a NULL check, as
engine specific init is done later in Driver load sequence.
v4:
- Use !!dev_priv->engine[VCS] style for the engine check in getparam. (Chris)
- Kill the superfluous init_engine_lists().
v5:
- Cleanup the intel_engines_init() & intel_engines_setup(), with respect to
allocation of intel_engine_cs structure. (Chris)
v6:
- Rebase.
v7:
- Optimize the for_each_engine_masked() macro. (Chris)
- Change the type of 'iter' local variable to enum intel_engine_id. (Chris)
- Rebase.
v8: Rebase.
v9: Rebase.
v10:
- For index calculation use engine ID instead of pointer based arithmetic in
intel_engine_sync_index() as engine pointers are not contiguous now (Chris)
- For appropriateness, rename local enum variable 'iter' to 'id'. (Joonas)
- Use for_each_engine macro for cleanup in intel_engines_init() and remove
check for NULL engine pointer in cleanup() routines. (Joonas)
v11: Rebase.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476378888-7372-1-git-send-email-akash.goel@intel.com
We currently capture the GPU state after we detect a hang. This is vital
for us to both triage and debug hangs in the wild (post-mortem
debugging). However, it comes at the cost of running some potentially
dangerous code (since it has to make very few assumption about the state
of the driver) that is quite resource intensive.
This patch introduces both a method to disable error capture at runtime
(for users who hit bugs at runtime and need a workaround) and to disable
error capture at compiletime (for realtime users who want to minimise
any possible latency, and never require error capture, saving ~30k of
code). The cost is that we now have to be wary of (and test!) a kconfig
flag and a module parameter. The effect of the module parameter is easy
to verify through code inspection and runtime testing, but a kconfig flag
needs regular compile checking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch
Link: http://patchwork.freedesktop.org/patch/msgid/20161012090522.367-2-chris@chris-wilson.co.uk
It's been over two months, git definitely lost it's marbles. Conflicts
resolved by picking our version, plus manually checking the diff with
the parent in drm-intel-next-queued to make sure git didn't do
anything stupid. It did, so I removed 2 occasions where it
double-inserted a bit of code. The diff is now just
- kernel-doc changes
- drm format/name changes
- display-info changes
so looks all reasonable.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
DPLL_SDVO_HIGH_SPEED must be set for SDVO/HDMI/DP, but nowhere is it
forbidden to set it for LVDS/CRT as well. So let's also set it on
CRT to make it possible to share the DPLL between HDMI and CRT.
What that bit apparently does is enable the x5 clock to the port,
which then pumps out the bits on both edges of the clock. The DAC
doesn't need that clock since it's not pumping out bits, but I don't
think it hurts to have the DPLL output that clock anyway.
This is fairly important on IVB since it has only two DPLLs with three
pipes. So trying to drive three or more PCH ports with three pipes
is only possible when at least one of the DPLLs gets shared between
two of the pipes.
SNB doesn't really need to do this since it has only two pipes. It could
be done to avoid enabling the second DPLL at all in certain cases, but
I'm not sure that's such a huge win. So let's not do it for SNB, at
least for now. On ILK it never makes sense as the DPLLs can't be shared.
v2: Just always enable the high speed clock to keep things simple (Daniel)
Beef up the commit message a bit (Daniel)
Cc: Nick Yamane <nick.diego@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Tested-by: Nick Yamane <nick.diego@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97204
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474878646-17711-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
(cherry picked from commit 7d7f8633a8)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
And use it to move knowledge about the SAGV-supporting platforms from
the callers to the SAGV code.
We'll add more platforms to intel_has_sagv(), so IMHO it makes more
sense to move all this to a single function instead of patching all
the callers every time we add SAGV support to a new platform.
v2: Move I915_SAGV_NOT_CONTROLLED to the new function (Lyude).
Cc: stable@vger.kernel.org
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474578035-424-3-git-send-email-paulo.r.zanoni@intel.com
(cherry picked from commit 56feca9197)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The plan is to introduce intel_has_sagv() and then use it to discover
which platforms actually support it.
I thought about keeping the functions with their current skl names,
but found two problems: (i) skl_has_sagv() would become a very
confusing name, and (ii) intel_atomic_commit_tail() doesn't seem to be
calling any functions whose name start with a platform name, so the
"intel_" naming scheme seems make more sense than the "firstplatorm_"
naming scheme here.
Cc: stable@vger.kernel.org
Reviewed-by: Lyude <cpaul@redhat.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474578035-424-2-git-send-email-paulo.r.zanoni@intel.com
(cherry picked from commit 16dcdc4edb)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We never remembered to set it (so it was zero), but this was not a
problem in the past due to the way handled the hardware registers.
Unfortunately we changed how we set the hardware and forgot to set
intel_crtc->dspaddr_offset.
This started to reflect on a few kms_frontbuffer_tracking subtests
that relied on page flips with CRTCs that don't point to the x:0,y:0
coordinates of the frontbuffer. After the page flip the CRTC was
showing the x:0,y:0 coordinate of the frontbuffer instead of
x:500,y:500. This problem is present even if we don't enable FBC or
PSR.
While trying to bisect it I realized that the first bad commit
actually just gives me a black screen for the mentioned tests instead
of showing the wrong x:0,y:0 offsets. A few commits later the black
screen problem goes away and we get to the point where the code is
today, but I'll consider the black screen as the first bad commit
since it's the point where the IGT subtests start to fail.
Fixes: 6687c9062c ("drm/i915: Rewrite fb rotation GTT handling")
Testcase: kms_frontbuffer_tracking/fbc-1p-primscrn-shrfb-pgflip-blt
Testcase: kms_frontbuffer_tracking/fbc-1p-primscrn-shrfb-evflip-blt
Testcase: kms_frontbuffer_tracking/fbc-1p-shrfb-fliptrack
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471644203-23463-1-git-send-email-paulo.r.zanoni@intel.com
(cherry picked from commit 4c0b8a8bc4)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reapply the PPS register unlock workaround after GPU reset on platforms
where the reset clobbers the display HW state. This at least gets rid of
the related WARN during LVDS encoder enabling on PNV.
Fixes: ed6143b8f7 ("drm/i915/lvds: Restore initial HW state during encoder enabling")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473847453-4771-1-git-send-email-imre.deak@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 51f592050a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
DPLL_SDVO_HIGH_SPEED must be set for SDVO/HDMI/DP, but nowhere is it
forbidden to set it for LVDS/CRT as well. So let's also set it on
CRT to make it possible to share the DPLL between HDMI and CRT.
What that bit apparently does is enable the x5 clock to the port,
which then pumps out the bits on both edges of the clock. The DAC
doesn't need that clock since it's not pumping out bits, but I don't
think it hurts to have the DPLL output that clock anyway.
This is fairly important on IVB since it has only two DPLLs with three
pipes. So trying to drive three or more PCH ports with three pipes
is only possible when at least one of the DPLLs gets shared between
two of the pipes.
SNB doesn't really need to do this since it has only two pipes. It could
be done to avoid enabling the second DPLL at all in certain cases, but
I'm not sure that's such a huge win. So let's not do it for SNB, at
least for now. On ILK it never makes sense as the DPLLs can't be shared.
v2: Just always enable the high speed clock to keep things simple (Daniel)
Beef up the commit message a bit (Daniel)
Cc: Nick Yamane <nick.diego@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Tested-by: Nick Yamane <nick.diego@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97204
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474878646-17711-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX6H4uAAoJEHm+PkMAQRiG5sMH/3yzrMiUCSokdS+cvY+jgKAG
JS58JmRvBPz2mRaU3MRPBGRDeCz/Nc9LggL2ZcgM+E1ZYirlYyQfIED3lkqk5R07
kIN1wmb+kQhXyU4IY3fEX7joqyKC6zOy4DUChPkBQU0/0+VUmdVmcJvsuPlnMZtf
g95m0BdYTui+eDezASRqOEp3Lb5ONL4c3ao4yBP0LHF033ctj3VJQiyi5uERPZJ0
5e6Mo7Wxn78t9WqJLQAiEH46kTwT2plNlxf3XXqTenfIdbWhqE873HPGeSMa3VQV
VywXTpCpSPQsA8BYg66qIbebdKOhs9MOviHVfqDtwQlvwhjlBDya0gNHfI5fSy4=
=Y/L5
-----END PGP SIGNATURE-----
Merge tag 'v4.8-rc8' into drm-next
Linux 4.8-rc8
There was a lot of fallout in the imx/amdgpu/i915 drivers, so backmerge
it now to avoid troubles.
* tag 'v4.8-rc8': (1442 commits)
Linux 4.8-rc8
fault_in_multipages_readable() throws set-but-unused error
mm: check VMA flags to avoid invalid PROT_NONE NUMA balancing
radix tree: fix sibling entry handling in radix_tree_descend()
radix tree test suite: Test radix_tree_replace_slot() for multiorder entries
fix memory leaks in tracing_buffers_splice_read()
tracing: Move mutex to protect against resetting of seq data
MIPS: Fix delay slot emulation count in debugfs
MIPS: SMP: Fix possibility of deadlock when bringing CPUs online
mm: delete unnecessary and unsafe init_tlb_ubc()
huge tmpfs: fix Committed_AS leak
shmem: fix tmpfs to handle the huge= option properly
blk-mq: skip unmapped queues in blk_mq_alloc_request_hctx
MIPS: Fix pre-r6 emulation FPU initialisation
arm64: kgdb: handle read-only text / modules
arm64: Call numa_store_cpu_info() earlier.
locking/hung_task: Fix typo in CONFIG_DETECT_HUNG_TASK help text
nvme-rdma: only clear queue flags after successful connect
i2c: qup: skip qup_i2c_suspend if the device is already runtime suspended
perf/core: Limit matching exclusive events to one PMU
...
And use it to move knowledge about the SAGV-supporting platforms from
the callers to the SAGV code.
We'll add more platforms to intel_has_sagv(), so IMHO it makes more
sense to move all this to a single function instead of patching all
the callers every time we add SAGV support to a new platform.
v2: Move I915_SAGV_NOT_CONTROLLED to the new function (Lyude).
Cc: stable@vger.kernel.org
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474578035-424-3-git-send-email-paulo.r.zanoni@intel.com
The plan is to introduce intel_has_sagv() and then use it to discover
which platforms actually support it.
I thought about keeping the functions with their current skl names,
but found two problems: (i) skl_has_sagv() would become a very
confusing name, and (ii) intel_atomic_commit_tail() doesn't seem to be
calling any functions whose name start with a platform name, so the
"intel_" naming scheme seems make more sense than the "firstplatorm_"
naming scheme here.
Cc: stable@vger.kernel.org
Reviewed-by: Lyude <cpaul@redhat.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474578035-424-2-git-send-email-paulo.r.zanoni@intel.com
We never remembered to set it (so it was zero), but this was not a
problem in the past due to the way handled the hardware registers.
Unfortunately we changed how we set the hardware and forgot to set
intel_crtc->dspaddr_offset.
This started to reflect on a few kms_frontbuffer_tracking subtests
that relied on page flips with CRTCs that don't point to the x:0,y:0
coordinates of the frontbuffer. After the page flip the CRTC was
showing the x:0,y:0 coordinate of the frontbuffer instead of
x:500,y:500. This problem is present even if we don't enable FBC or
PSR.
While trying to bisect it I realized that the first bad commit
actually just gives me a black screen for the mentioned tests instead
of showing the wrong x:0,y:0 offsets. A few commits later the black
screen problem goes away and we get to the point where the code is
today, but I'll consider the black screen as the first bad commit
since it's the point where the IGT subtests start to fail.
Fixes: 6687c9062c ("drm/i915: Rewrite fb rotation GTT handling")
Testcase: kms_frontbuffer_tracking/fbc-1p-primscrn-shrfb-pgflip-blt
Testcase: kms_frontbuffer_tracking/fbc-1p-primscrn-shrfb-evflip-blt
Testcase: kms_frontbuffer_tracking/fbc-1p-shrfb-fliptrack
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471644203-23463-1-git-send-email-paulo.r.zanoni@intel.com
