There are multiple statements that are indented incorrectly. Add
in the missing tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_hubp.c:
In function hubp21_set_vm_system_aperture_settings:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_hubp.c:343:23:
warning: variable mc_vm_apt_default set but not used [-Wunused-but-set-variable]
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
when changing display clock, SMU need to use power up DFS and use
DENTIST to ramp DFS DID to switch target frequency before switching back
to bypass.
[How]
fixed the minimum display clock to 100MHz, it's W/A the same with PCO.
Signed-off-by: Yu-ting Shen <Yu-ting.Shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System will crash when trying to access local sink in
core_link_enable_stream in MST case.
[How]
Access patches directly from stream.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow sometimes occurs during transition into MPO with stutter
enabled.
[How]
When transitioning into MPO, disable stutter. Re-enable stutter within
one frame.
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently clock table struct is very far down in the bounding box struct
making it hard to find while debugging, especially when using the
dal3dbgext.
[HOW]
Move it up so it is the first struct defined, and therefore much easier
to find and access.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some display configuration like 1080P monitor playing a 1080P video,
if user use ALT+F4 to exit Movie and TV, there is a chance clocks are
same only water mark changed. Current clock optimization machanism will
result in water mark keeps high after exit Movie and TV app.
[How]
Return if watermark need to be optimized when doing program watermark,
perform the optimization after.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to assign surface size rather than viewport size for surface size
dml variable.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to update TTU properly if DRAMClockChangeWatermark changes. If
TTU < DRAMClockChangeWatermark, we pstate won't be allowed and we will
hang in some PSR cases.
[How]
Update TTU if DramClockChangeWatermark value increases (only if TTU was
dependent on the watermark value on the DRAMClockChangeWatermark value
in the first place).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
RV2 and variants are indistinguishable by hw internal rev alone, need to
be distinguishable in order to correctly set max vlevel. Previous
detection change incorrectly checked for hw internal rev.
[HOW]
Use pci revision to check if RV2 or low power variant Correct a few
overlapping ASICREV range checks
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.
[How]
Add infrastructure to enable and disable PSR on DMCUB.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update dcn20_populate_dml_pipes_from_context to correctly handle odm
when no surface is provided.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DalMPVisualConfirm does not support FreeSync 2 ARGB2101010 which causes
black visual confirm bar when playing HDR video on FreeSync 2 display in
full screen mode
[How]
Added pink color for DalMPVisualConfirm on FreeSync 2 ARGB2101010
surface
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously implemented early_cr_pattern was link level but the whole
asic should be affected.
[How]
- change old link flag to dc level
- new bit in dc->work_arounds set by DM
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some displays clear ignore MSA bit on mode change, which cause
blackscreen when programming variable vtotals. Ignore MSA bit needs
programming needs to be delayed or re-set to be retained.
[How]
Create patch to delay programming ignore MSA bit after unblanking
stream.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A software workaround is required for all vendor-built cards on platform.
[How]
When performing DP link training, we must send TPS1 before DPCD:100h is
written with the proper bit rate value. This change must be applies in
ALL cases when LT happens.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Not programming dto with same values causes test failures in DCN2 diags
DPP tests.
[HOW]
This reverts commit 1b53e73323.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently DAL programs negative slope for the last point of output
transfer function curve.
[How]
Applying a check for the last PWL point for RGB values not to be
smaller than previous. If smaller, initialize the last point values
to a sum of previous PWL value and previous PWL delta;
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are some structures and functions meant only to be used in the
scope of that single rn_clk_mgr c file.
[How]
Make structs and funcs static if only meant to be used within
rn_clk_mgr
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make panel backlight and power on/off functions into
hardware specific function pointers
[How]
Add function pointers for panel related hw functions
- is_panel_powered_on
- is_panel_backlight_on
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Add optimization to allow pstate change support when all displays
are off in DCN2.
[How]
Add clk_mgr_helper_get_active_plane_cnt() to sum plane_count for all
valid stream_status[]. If plane_count is 0, then there are no active
or virtual streams present. Use plane_count == 0 as extra condition to
enable p_state_change_support in dcn2_update_clocks().
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
According to HW team, PG is dropped for NV12, but programming
the registers will still cause power to be consumed, so don't
program for NV12.
[How]
Set function pointer to NULL if NV12
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bugs occur when TX interrupt comes in when no USB-C on board.
[How]
Check PHY for USB-C before enabling TX interrupt in DMCU FW.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently there is a minor error in scaling filter coefficients
caused by truncation to fit the HW registers.This error accummulates
with increased taps, but has gone unnoticed due to vast majority of
scaling being done with only 4 taps.
Scaling filters are now updated using HW team's filter generator
which has quantization error minimization built in.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Since the i2c payload allocation can fail need to check return codes
[How]
Clean up i2c payload allocations and check for errors
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
core_link_read_dpcd() will invoke dm_helpers_dp_read_dpcd(),
which needs to read dpcd info with the help of aconnector.
If aconnector (dc->links[i]->prev) is NULL, then dpcd status
cannot be read.
As a result, dpcd read fails and a line of error will be
printed out in dmesg.log as:
"*ERROR* Failed to found connector for link!"
[How]
Make sure that aconnector (dc->links[i]->prev) is not NULL,
then read dpcd status.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Joseph Gravenor <Joseph.Gravenor@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
../drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:980:36:
warning: address of 'sink->edid_caps.panel_patch.skip_scdc_overwrite'
will always evaluate to 'true' [-Wpointer-bool-conversion]
if (&sink->edid_caps.panel_patch.skip_scdc_overwrite)
~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~
1 warning generated.
This is probably not what was intended so remove the address of
operator, which matches how skip_scdc_overwrite is handled in the rest
of the driver.
While we're here, drop an extra newline after this if block.
Fixes: a760fc1bff ("drm/amd/display: add monitor patch to disable SCDC read/write")
Link: https://github.com/ClangBuiltLinux/linux/issues/879
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's used by more than just DCN2.0. Fixes missing symbol when
amdgpu is built without DCN support.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
to cover dcn2.x related headers.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN hardware sequencer we do actually call ATOM_INIT correctly per
pipe. The workaround is not necessary for command table offloading.
[How]
Drop the workaround since it's not needed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow is observed when plug in a 4K@60 monitor with
1366x768 eDP due to DPPCLK is too low.
[How]
Limit minimum DPPCLK to 100MHz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Engine can be NULL in some cases, so we must not acquire it.
[How]
Check for NULL engine before acquiring.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Previously drain clk was unconstrained and fill clk was constrained on fclk.
We want to change it to fill clk unconstrained and drain clock constrained
to dcfclk.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:
In function dcn10_post_unlock_program_front_end:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:2623:29:
warning: variable stream_status set but not used [-Wunused-but-set-variable]
commit bbf5f6c3f8 ("drm/amd/display: Split program front end part that occur outside lock")
involved this unused variable.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver needs to know PSR state.
[How]
Use GPINT to call to firmware and get psr state.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN hardware sequencer we do actually call ATOM_INIT correctly per
pipe. The workaround is not necessary for command table offloading.
[How]
Drop the workaround since it's not needed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
customer issue: found that for their specific panel, EDID register space
being overwritten during SCDC read write
[how]
customer accepted HDMI 2 features not working - disabled SCDC read/write
as well as HDMI 2 in general based on monitor patch
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently odm scaling calculations are only done when adding initial
odm pipe. Any scaling re-calculations will mess up odm because of this.
This change resolves the problem by updating scaling split logic to
handle odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the struct dc_panel_patch, we have a field named
manage_secondary_link which is not used by any part of the code. This
commit drops the unused field.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some register defines are redundant or updated
[How]
Update register defines
Remove some redundant defines
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Wyatt Wood <Wyatt.Wood@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Sun peng Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
in dcn10_apply_ctx_for_surface(), if we hit !top_pipe_to_program,
pipe_ctx->update_flags could not get cleared.
[How]
Moved clearing pipe_ctx->update_flags logic before if
(!top_pipe_to_program) to gurantee pipe_ctx->update_flags get cleared.
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Set version is currently not called.
[How]
Add call to set version from copy settings. This
should be the only time this is called as the eDP
caps should never change.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Vendor dongle requires propietary OUI and handshake sequence.
[HOW]
Add a new structure to dc_init_data, to allow creator to pass
an override vendor_oui. This value will be written to DP_SOURCE_OUI
instead of AMD signature, when dpcd_set_source_specific_data is
called.
Signed-off-by: Calvin Hou <Calvin.Hou@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With the fallback case in place for command table offloading via DMCUB
it's no longer an error for the command table to be missing specific
entries.
[How]
Drop the BREAK_TO_DEBUGGER();
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
before we exit early in edp_reciever_ready if we detect that panel
is not edp or below rev 1.2. This will skip the backlight/t7 delay panel
patch.
[how]
edit logic to ensure panel patch is applied regardless of edp rev.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, gcc spews a warning as:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hubbub.c: In function ‘hubbub1_verify_allow_pstate_change_high’:
./include/drm/drm_print.h:316:2: warning: ‘debug_data’ may be used uninitialized in this function [-Wmaybe-uninitialized]
This is because the code checks against a static value although it's
basically a constant and guaranteed to be set.
This patch changes the type prefix from static to const for addressing
the compile warning above and also for letting the compiler optimize
better.
Fixes: 62d591a8e0 ("drm/amd/display: create new files for hubbub functions")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
not turning off the mst hub before detection on reboot
causes us to not be able to light up displays with mst hook
[how]
on hw init, see if any displays are lit up. if so, turn them off
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
these registers should have been double buffered. SW workaround we will have SW program the more aggressive (lower) values
whenever we are upating this register, so we will not have underflow at expense of less optimzal request pattern.
[How]
there is a driver bug where we don't check for 0, which is uninitialzed HW default. since 0 is smaller than any value we need to program,
driver end up with not programming these registers
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] old panel has been enabled for window driver but not linux.
[How] enable oled panel support for linux. this patch is dc part.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow is observed when plug in a 4K@60 monitor with
1366x768 eDP due to DPPCLK is too low.
[How]
Limit minimum DPPCLK to 100MHz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
enum dc_log_type has more than 32 entries. User cannot set larger entries,
like LOG_DSC. Logs from LOG_GAMMA_DEBUG where being printed even though
flag was not enabled, because dal_logger_should_log check erroneously
passed.
[HOW]
Change struct dal_logger.mask and struct dc_init_data.mask to uint64_t.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Having watermark ranges saved inside clk_mgr to be
available for debug at all times would be useful.
Add it to the clk_mgr_internal struct for reference.
Only populated for Renoir, unused for other asics.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
hyperV flag should be passed from dm to DC, and override the
nv12 flip workaround flag.
[How]
Add flag to phy address config struct and pass the value in dm.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous logic is only good for 15W parts. Other configuration
need a smarter logic to match clk levels with pp table in the fuse.
[How]
Cache all 8 DPM level's clock data, find lvl that match each pstate
in the pp table and build input into DML base on that
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
hwss should not guess what type of pipe lock is needed.
The caller of the lock function should know
the right type of pipe lock.
Decouple the setup of global lock outside of pipe control lock
logic.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Engine can be NULL in some cases, so we must not acquire it.
[How]
Check for NULL engine before acquiring.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Previously drain clk was unconstrained and fill clk was constrained on fclk.
We want to change it to fill clk unconstrained and drain clock constrained
to dcfclk.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
new HW engine mapping requirment use in PSP
[how]
report stream_enc_inst
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The break in apply_ctx_interdependent_lock() may potentially
lead to early break from the loop leaving update plane unlocked
[How]
Remove break
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
int i can go out of boundary which will cause crash
[How]
Fixed the maximum value of i to avoid i going out of boundary
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After locking refactor GSL is not acquired properly
resulting in immediate flip issues.
[How]
Do not copy old GSL state anymore since GSL is acquired
earlier now.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Screen flickering when HDR switches between FP16 and ARGB2101010
[How]
Moved pipe_control_lock so stream update and plane update occur atomically
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Lucy Li <lucy.li@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Diagnostics team reported various issues found when enabling warnings as errors
[How]
Fix implicit conversions
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC updates only set type to FULL UPDATE, but doesn't
flag the change
[How]
Add DSC flag update flag
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Eventually want to lock at a higher level in stack.
To do this, we need to be able to isolate the parts that need to be done
after pipe unlock.
[How]
Split out programming that is done post unlock.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why/how]
We found out that the register we read actually gets reset by SMU
after we loose power, meaning this always returns true
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The call to dp_enable_link_phy are using default/invalid values for clock id
and link settings.
[How]
Move workaround code to after its parameter variables are determined.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Must know psr version during runtime.
[How]
Add set psr version message structures.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We might get different numbers of clocks from powerplay depending
on what the OEM has populated.
v2: add assert for at least one level
Bug: https://gitlab.freedesktop.org/drm/amd/issues/963
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In current code we're essentially drawing the cursor on every pipe
that contains it. This only works when the planes have the same
scaling for src to dest rect, otherwise we'll get "double cursor" where
one cursor is incorrectly filtered and offset from the real position.
[How]
Without dedicated cursor planes on DCN we require at least one pipe
that matches the scaling of the current timing.
This is an optimization and workaround for the most common case where
the top-most plane is not scaled but the bottom-most plane is scaled.
Whenever a pipe has a parent pipe in the blending tree whose recout
fully contains the current pipe we can disable the pipe.
This only applies when the pipe is actually visible of course.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A for-loop is iterating from 0 up to 1000 however the loop variable count
is a u8 and hence not large enough. Fix this by making count an int.
Also remove the redundant initialization of count since this is never used
and add { } on the loop statement make the loop block clearer.
v2: drop useless else (Walter Harms)
Addresses-Coverity: ("Operands don't affect result")
Fixes: ed581a0ace ("drm/amd/display: wait for update when setting dpg test pattern")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allocation isn't required and can fail when resuming from suspend.
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1009
Signed-off-by: Dor Askayo <dor.askayo@gmail.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 80adaebd2d.
[WHY]
This change was working around a regression that occured in this:
commit 0301ccbaf6 ("drm/amd/display: DP Compliance 400.1.1 failure")
With the fix to run verify_link_cap when the SINK_COUNT of
dongles becomes non-zero this change is no longer needed.
Cc: Louis Li <Ching-shih.Li@amd.com>
Cc: Wenjing Liu <Wenjing.Liu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Two years ago the patch referenced by the Fixes tag stopped running
dp_verify_link_cap_with_retries during DP detection when the reason
for the detection was a short-pulse interrupt. This effectively meant
that we were no longer doing the verify_link_cap training on active
dongles when their SINK_COUNT changed from 0 to 1.
A year ago this was partly remedied with:
commit 80adaebd2d ("drm/amd/display: Don't skip link training for empty dongle")
This made sure that we trained the dongle on initial hotplug (without
connected downstream devices).
This is all fine and dandy if it weren't for the fact that there are
some dongles on the market that don't like link training when SINK_COUNT
is 0 These dongles will in fact indicate a SINK_COUNT of 0 immediately
after hotplug, even when a downstream device is connected, and then
trigger a shortpulse interrupt indicating a SINK_COUNT change to 1.
In order to play nicely we will need our policy to not link train an
active DP dongle when SINK_COUNT is 0 but ensure we train it when the
SINK_COUNT changes to 1.
[HOW]
Call dp_verify_link_cap_with_retries on detection even when the detection
is triggered from a short pulse interrupt.
With this change we can also revert this commit which we'll do in a separate
follow-up change:
commit 80adaebd2d ("drm/amd/display: Don't skip link training for empty dongle")
Fixes: 0301ccbaf6 ("drm/amd/display: DP Compliance 400.1.1 failure")
Suggested-by: Louis Li <Ching-shih.Li@amd.com>
Tested-by: Louis Li <Ching-shih.Li@amd.com>
Cc: Wenjing Liu <Wenjing.Liu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
FMT has limitation to support YCbCr420 with h_active greater than 4096.
[how]
Use odm combine to overcome the limitation.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver didn't init hw i2c speed cause hdcp hw cannot
send command, because the default value of speed register
is 0x2.
[How]
Restore the default speed when release i2c engine
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MPO isn't enabled on some 4k videos due to video source width is 4096
and the current limit is 3840.
[How]
Changed the limit to 4096.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
MSA will be deprecated in the future.
Need to support VSC during DP test automation.
[how]
Do not disable VSC during DP test automation.
TODO - need to add VSC update on DM side on test request.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCUB command table doesn't support ATOM_ENABLE/ATOM_DISABLE anymore
so we never end up calling the DCN init path in DMCUB.
[How]
Map ATOM_ENABLE to ATOM_INIT only for DMCUB command table offloading.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardcoded fixed values are not proper.
[How]
Use enum values instead of fixed numbers.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In HG mode, vbios didn't call DispController_Init to program NV1x
XTAL_REF_DIV value when ASIC_INIT, but driver read XTAL_REF_DIV
to calculate i2c reference frequency. it cause i2c frequency change
from 100kHz to 200kHz.
[How]
remove get_speed function and calculate reference frequency at
set_speed functiton.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The types for dummyinteger1 and dummyinteger2 are unsigned
as part of the DML spec. They should not be long.
[How]
Make them unsigned int instead of long.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver use pipe_ctx to reallocate payload may cause allocate
payload twice on same sink with split pipe.
[How]
Drvier must to check pipe_ctx is split pipe or not to avoid
reallocate payload twice on same sink.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the command table isn't available then we can fallback to DMCUB
offloading if it's enabled and available.
[How]
Instead of assigning NULL for supported command table functions we can
fallback to the DMCUB when it's available.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Empty dsc enc caps when debug option is set to disable DSC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DP 1.4a Spec requires that training pattern only under certain
specific conditions. Currently driver will re-send
training pattern every time voltage swing value changes,
but that should not be the case.
[How]
Do not re-send training pattern every time VS values
are different. Only send it on the first iteration.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On video test pattern request we need to update MSA and VSC so
it will match the requested test pattern dynamic range field.
[how]
Update dynamic range field in MSA and disable VSC as updating VSC
info packet is complicated and not required for test pattern purpose.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DPG is used to generate both blank and test automation test pattern.
When test automation is running the requested test pattern can be
overriden by the blank or unblank call because it is using the same
hardware.
[how]
When test pattern is requested, skip blank or unblank.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Try to allocate MST payload but receive HPD short pulse with link loss
casue driver allocate payload twice. It cause monitor can't light up
successfully.
[How]
When driver receive HPD short pulse with link loss, we need to
deallocate payload then allocate payload.
Then we will not allocate payload twice with same sink.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to fix DML portability issues to enable SW unit testing around DML
[how]
Move calcs into dc include folder since multiple components reference it
Remove relative paths to external dependencies
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The rapid msleep operation causes the white line garbage when
DAL check flip pending status in SetVidPnSourceVisibility.
To execute this msleep will induce context switch, and longer
delay could cause worse garbage situation.
[how]
To replace msleep with mdelay.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only need to do surface flip for video plane via dmcub.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently if seamless boot is enabled, we will skip double buffer enable
for OTG_BLANK. However, we need the double buffer enable in order to
block global sync signals when OTG becomes blanked (for PSR). Blocking
global sync signals prevent pipe from requesting data.
[How]
Move tg_init before seamless boot check.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dpcd cap mismatch in 2200 vs base
[How]
Add monitor patch which using based caps to overwrite 2200
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently we wait for test pattern after each pipe is programmed. For
ODM combined scenario it will cause test pattern is shown on only half
screen for 1 frame. This is not desirable.
[how]
No wait between odm pipe programming, only wait after all pipes are
programmed.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With different refresh rate panels, the PSR entry/exit time is
different since it is dependent on 2 frame entry time today
[How]
Make static screen num frame entry time to be calculated
such that entry time is within 30 ms instead of fixed num
frames.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCU need to wait a vblank to handle psr enter command. When psr exit
coming before vblank, the psr exit command will be skip because current
psr state is disable.
[How]
remove psr state condition when psr exit case
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML Initialization was previously done on dcn21_resource initialization.
This meant that DML soc struct was populated with hardcoded values.
[How]
Move DML initialization to after updating bounding box, to use clock table
values from SMU.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PHY will sometimes be in bad state on hotplugging display from USB-C
dongle.
[How]
Add additional calls to disable and then enable PHY before link training
starts during verify_link_cap.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rework surface programming for RN to separate preparing parameters and
register programming.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Recent double buffering changes for dcn2 use IX_REG_READ.
However, this macro returns the full register value, with the need to
manually shift and mask it to retrieve field data.
[How]
Create new IX_REG_GET macro that handles shift and mask.
Use this for double buffering reads instead of IX_REG_READ.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Programming surface flip addresses via dmcub uC for optimizing the data
flush.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting color temperature, screen tearing was observed.
This was due to overwritten values in gamut remap registers.
This issue was solved for OCSC and ICSC by alternating between "A" and
"B" registers to double buffer the writes.
[How]
Create new set_gamut_remap and program_gamut_remap for dcn20.
Alternate which registers are written to by switching modes each time.
Also fixes ICSC mode reg read to use proper data offset.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Moving PSR from DMCU to DMCUB.
[How]
Add driverside PSR changes required to send inbox messages to fw.
These changes are non-functional until the psr structure allocation
is uncommented.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting video brightness, screen tearing was observed.
This was due to overwritten values in ICSC registers. In dcn10, this issue had been
fixed by implementing double buffering via alternating ICSC modes.
However, the second register set used in dcn1 doesn't exist in dcn2.
[How]
Create new program_input_csc for dcn20.
Use ICSC_B registers instead of COMA registers as second set.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add more fields to support upcoming dml versions
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Don't want to start HW discovery unless we have lost power,
as doing rediscovery otherwise is both unnecessary and time consuming.
Before this change it takes 40 seconds to go in to suspend, after it
takes 27 seconds
[How]
Accelerated mode gets cleared if we lose power. Only do detection if
this register is cleared
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Test pattern should be applied to hardware when exiting set test pattern
function.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
48mhz turn off feature does not work on HDMI and DVI, but the feauture
was only blocked on HDMI, this change will apply the same wa on DVI
[HOW]
Apply workaround for all TMDS signal types (HDMI, DVI single/dual link)
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If dummy pstate latency is 0 we should report the actual
pstate support, and not that pstate is always supported.
[How]
Don't always program pstate support true
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure that lttpr_caps has the mode set to repeater.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting colour properties (e.g. brightness), screen tearing was observed.
This was due to overwritten values in OCSC registers. In dcn10, this issue had been fixed by
implementing double buffering by alternating OCSC modes.
[How]
Alternate which OCSC registers are used by switching modes each time.
This double buffers the CSC writes.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
While doing seamless boot I made some changes
to dcn2 hubbub functions, missed a link
[how]
link hubbub1 func to hubbub2 usage. It has already
been successfully linked in dcn1 and 3.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If the specific monitor supports DSC, the secondary link should be
disabled, and the other way around, too: if either that monitor or
our ASIC doesn't support DSC, the secodary link should be enabled.
[how]
Add a monitor patch and disable secondary link if that monitor
is detected and if ASIC supports DSC, or otherwise enable secondary
link.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Needed to reprogram vblank_start in dml properly in order to get the
correct dlg params to program VTG.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous implementation we may have residual chroma address offset
if transition from wa enable -> wa disable.
[How]
Clear address offset cache when viewport updates. Also update the
vp size check condition to account for rotation angle
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The conversion to bool is not needed, remove it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
read_current_link_settings_on_detect() on eDP 1.4+ may use the
edp_supported_link_rates table which is set up by
detect_edp_sink_caps(), so that function needs to be called first.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Martin Leung <martin.leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Only a single voltage level should be available to Pollock (min level)
Pollock & Dali get misidentified as Renoir, use wrong clk mgr constructor
[HOW]
Add provided Pollock IDs to ASIC Rev. ID list.
Create new Pollock ASIC RID check, fix RV2 & Dali ASIC checks.
Check RID and set max voltage level to 0 if Pollock is detected.
Work around broken ASICREV_IS_RENOIR, IS_RAVEN2, etc. checks by
performing Dali/Pollock checks before they can be misidentified as RN.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a use case that link loss happens accidentally,
and we need to recover that link loss as soon as possible.
Under this circumstance, we will perform link training,
and try to recover the link that's just lost.
However, if link PHY is disabled before link training
happens, then DP display will never come back again.
Also, please note that dropping this disable_phy function
call won't break USB-C hotplug functionality.
(This line of code was firstly introduced associated with
a patch to fix USB-C hotplug issue)
[How]
Don't disable DP transmitter and its encoder before link
training happens, even if link loss is detected.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If there is limited link bandwidth on a MST network,
it must be divided fairly between the streams on that network
Implement an algorithm to determine the correct DSC config
for each stream
The algorithm:
This
[ ] ( )
represents the range of bandwidths possible for a given stream.
The [] area represents the range of DSC configs, and the ()
represents no DSC. The bandwidth used increases from left to right.
First, try disabling DSC on all streams
[ ] (|)
[ ] (|)
Check this against the bandwidth limits of the link and each branch
(including each endpoint). If it passes, the job is done
Second, try maximum DSC compression on all streams
that support DSC
[| ] ( )
[| ] ( )
If this does not pass, then enabling this combination of streams
is impossible
Otherwise, divide the remaining bandwidth evenly amongst the streams
[ | ] ( )
[ | ] ( )
If one or more of the streams reach minimum compression, evenly
divide the reamining bandwidth amongst the remaining streams
[ |] ( )
[ |] ( )
[ | ] ( )
[ | ] ( )
If all streams can reach minimum compression, disable compression
greedily
[ |] ( )
[ |] ( )
[ ] (|)
Perform this algorithm on each full update, on each MST link
with at least one DSC stream on it
After the configs are computed, call
dcn20_add_dsc_to_stream_resource on each stream with DSC enabled.
It is only after all streams are created that we can know which
of them will need DSC.
Do all of this at the end of amdgpu atomic check. If it fails,
fail check; This combination of timings cannot be supported.
v2: Use drm_dp_mst_atomic_check to validate bw for certain dsc
configurations
v3: Use dc_dsc_policy structure to get min and max bpp rate
for DSC configuration
Acked-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For DSC MST, sometimes monitors would break out
in full-screen static. The issue traced back to the
PPS generation code, where these variables were being used
uninitialized and were picking up garbage.
memset to 0 to avoid this
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:85:6-13: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:88:2-9: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:225:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:226:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:251:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:252:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:256:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:257:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:267:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:269:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:682:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:1013:1-9: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:110:6-13: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:113:2-9: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:243:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:244:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:267:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:268:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:272:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:273:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:283:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:285:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:673:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:962:1-9: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:110:6-13: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:113:2-9: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:243:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:244:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:267:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:268:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:272:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:273:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:283:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:285:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:673:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:961:1-9: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:157:46-64: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:159:2-20: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:161:46-64: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:163:2-20: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:289:1-12: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:290:1-12: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:341:3-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:343:4-15: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_mode_vba_21.c:4124:3-28: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_mode_vba_21.c:4128:5-30: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_mode_vba_21.c:5207:3-37: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c:186:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c:189:2-10: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c:482:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c:485:2-10: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It's required for debug purposes.
[how]
Add a dsc_bpp_increment_div debug option that overrides DPCD
BITS_PER_PIXEL_INCREMENT value. The value dsc_bpp_increment_div should
be set to is the one after parsing, i.e. it could be 1, 2, 4, 8 or 16
(meaning 1pix, 1/2pix, ..., 1/16pix).
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDP is internal link and link loss is unexpected.
It is typically going to be PSR related errors, which is
handled separately.
[How]
Check for eDP and skip check for link loss
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor disappears for some SLS displays that are rotated 180
and 270 degrees. This occurs when there is no pipe split being
done ( ex. 3 or more displays ). The cursor calculations assume
pipe splitting is done so when it calculates the new cursor
position in hwss.set_cursor_position(), it is out-of-bounds so
it disables the cursor in hubp.set_cursor_position().
[How]
In non pipe split cases, calculate cursor using viewport size
( width or height ) instead of viewport size * 2 ( the two
because pipe splitting divides the rectangle into two ).
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous formula for calculating DPP CLK DTO was
hard to understand.
[How]
Replace with easier to understand formula that produces
same results.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A corner case currently exists where DPP DTO is lowered before
pipes are updated to a higher viewport. This causes underflow
as the DPPCLK is too low for the current viewport.
[How]
Only lower DPP DTO when it is safe to lower, or if
the newer clocks are higher than the current ones.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DAL3 should support SRIOV
[how]
Add support for the virtual dal flag. This flag should skip
most/all of DC construction since the HW isn't accessible, but
still construct WindowsDM (almost) normally but with only SW display
targets
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix manual trigger source correctly be TRIGA for DCN2
rather than MANUAL_FLOW.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN21 and DCN2 extended timeout support cap is not set correctly.
[How]
Set extended timeout support for ASIC families to their right values.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously update_bw_bounding_box for RN was commented out
due to incorrect values causing BSOD on Hybrid Graphics.
However, commenting out this function also may cause issues
such as underflow in certain cases such as 2x4K displays.
[How]
Fix dram_speed_mts calculations.
Update from proper index of clock_limits[]
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]:
According to eDP spec, max T7 delay should be 50 ms. Current code uses 300
retry counters may not be accurate enough for different panels.
[How]:
Use absolute time stamp to achive accurate delay.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we rotate 270 in mixed SLS mode, the recouts occupy the
right side of the display. So all the recout_skip_v values
are relative to the left side of the display. This causes
adjust_vp_and_init_for_seamless_clip() to incorrectly increase
the data->viewport.height for that recout. The rotation looks
like the bottom half is duplicated twice.
[How]
recout.x values are being adjusted based on
stream->timing.h_border_left. Instead of using h_border_left,
use dst.x to represent the border. Shift dst.x by the amount of
stream->timing.h_border_left and set
stream->timing.h_border_left to 0. Do all the calculations
and then revert stream->timing.h_border_left and
stream->dst.x back to their original values.
When calculating pipe_ctx->plane_res.scl_data.h_active,
make sure to use the original stream->timing.h_border_left
value.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain instances, there was a reliance on pipe indexing being accurate. However, this
assumption fails with harvesting of pipes 1 or 2, which can occur in production B6 parts.
HW hang would occur as a result.
[How]
Use hubp index for mpcc, and do mpc_init for all theoretical pipes (including disabled ones).
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After read the 3rd Edid blocks, we will reset segment to 0,
which causes this VR fail to read Edid successfully.
[How]
Skip to reset segment to 0 for this VR device.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. Set second screen only then unplug external monitor
2. Enter to S4 then plug in external monitor
3. Resume from S4, eDP will not turn off when OS set
second screen only
Sometimes OS will not set eDP power up cause eDP dpms_off
keep true then driver skipp disable stream
[How]
When drvier try to disable stream, add link status condition
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Up to 4 ODM memory pieces are required per ODM combine and cannot
overlap, i.e. each ODM "session" has to use its own memory pieces.
The ODM-memory mapping is currently broken for generic case.
The maximum number of memory pieces is ASIC-dependent, but it's always
big enough to satisfy maximum number of ODM combines. Memory pieces
are mapped as a bit-map, i.e. one memory piece corresponds to one bit.
The OPTC doing ODM needs to select memory pieces by setting the
corresponding bits, making sure there's no overlap with other OPTC
instances that might be doing ODM.
The current mapping works only for OPTC instance indexes smaller than
3. For instance indexes 3 and up it practically maps no ODM memory,
causing black, gray or white screen in display configs that include
ODM on OPTC instance 3 or up.
[how]
Statically map two unique ODM memory pieces for each OPTC instance
and piece them together when programming ODM combine mode.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add warmup escape support, for diags, in a way that is possible to
choose a new or an existing sequence. For achieving this goal, this
commit adds separated MCIF buffer as VCN request.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Scaling better handled by upper layers before pipe splitting.
[How]
Remove DC code for integer scaling and force cursor update if
viewport or scaling changes occur to prevent underflow from
invalid cursor position.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc previously had bugs that interfered with the ability to inherit a
timing from a device with multiple streams (without flash/blanking).
After this fix there is still a dependency on UEFI support.
[how]
fixed 3 bugs: loaded MPC state, changed bw_optimize flag to a counter
instead of a boolean, and reading dpp/disp clk from HW to ensure we
don't raise the clock's when we're not supposed to.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, pipe resources are assigned to an index that matches the pipe position.
However, if pipe 1 or 2 is disabled, there will be a gap in the arrays which causes a crash when iterating based on pipe_count.
[How]
Fix resource construct to assign resources to minimum available array index.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need previously implemented chroma vp wa to work for rotation cases.
[How]
Implement rotation specific wa.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is one opp per pipe. For certain RN parts, the fourth pipe is disabled, so there is no opp for it.
res_cap->num_opp is hardcoded to 4, so if we use that to iterate over opps we will crash.
[How]
Use the pipe_count value instead, which is not hardcoded and so will have the correct number.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
YQ should be limited range for all cases.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A hardcoded number is used today
[How]
Add definition for number of BL data points
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some use cases we need to be able to adjust the maximum target bpp
allowed by DSC policy.
[How]
New interface dc_dsc_policy_set_max_target_bpp_limit
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Lack of proper timing caused intermittent underflow on unplug external DP.
A previous fix was invalid and caused S0i3 regression, so had to be reverted.
[How]
When unlocking pipe, wait for no pipes to have flip pending before unlocking.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The earlier change: "check phy dpalt lane count config"
uses link encoder registers not defined properly.
That caused regression with mst-enabled display not
lighting up.
[How]
Add missing reg definitions.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc20 containes several FPU-dependent functions without proper FPU
kernel mode enable/disable wrappers. Add the required wrappers
for both x86 and POWER.
This enables Navi DC20 support for POWER systems.
v2: fix compilation
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN requires floating point support to operate. Add the appropriate
x86/ppc64 guards and FPU / AltiVec / VSX context switches to DCN.
Note that the current DC20 code doesn't contain all required FPU
wrappers on x86 or POWER, so this patch is insufficient to fully
enable DC20 on POWER.
v2: s/X86_64/X86/g to retain previous behavior.
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Introduce DC_FP_START()/DC_FP_END() macros to help enable floating
point kernel mode support across various architectures.
v2: move copyright update to commit which adds the changes
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-next-5.6-2019-12-11:
amdgpu:
- Add MST atomic routines
- Add support for DMCUB (new helper microengine for displays)
- Add OEM i2c support in DC
- Use vstartup for vblank events on DCN
- Simplify Kconfig for DC
- Renoir fixes for DC
- Clean up function pointers in DC
- Initial support for HDCP 2.x
- Misc code cleanups
- GFX10 fixes
- Rework JPEG engine handling for VCN
- Add clock and power gating support for JPEG
- BACO support for Arcturus
- Cleanup PSP ring handling
- Add framework for using BACO with runtime pm to save power
- Move core pci state handling out of the driver for pm ops
- Allow guest power control in 1 VF case with SR-IOV
- SR-IOV fixes
- RAS fixes
- Support for power metrics on renoir
- Golden settings updates for gfx10
- Enable gfxoff on supported navi10 skus
- Update MAINTAINERS
amdkfd:
- Clean up generational gfx code
- Fixes for gfx10
- DIQ fixes
- Share more code with amdgpu
radeon:
- PPC DMA fix
- Register checker fixes for r1xx/r2xx
- Misc cleanups
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191211223020.7510-1-alexander.deucher@amd.com
amdgpu is MIT licensed.
Fixes: ec8f24b7fa ("treewide: Add SPDX license identifier - Makefile/Kconfig")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calling kzalloc() and related functions requires the
linux/slab.h header to be included:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c: In function 'dcn21_ipp_create':
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c:679:3: error: implicit declaration of function 'kzalloc'; did you mean 'd_alloc'? [-Werror=implicit-function-declaration]
kzalloc(sizeof(struct dcn10_ipp), GFP_KERNEL);
A lot of other headers also miss a direct include in this file,
but this is the only one that causes a problem for now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu is MIT licensed.
Fixes: ec8f24b7fa ("treewide: Add SPDX license identifier - Makefile/Kconfig")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calling kzalloc() and related functions requires the
linux/slab.h header to be included:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c: In function 'dcn21_ipp_create':
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c:679:3: error: implicit declaration of function 'kzalloc'; did you mean 'd_alloc'? [-Werror=implicit-function-declaration]
kzalloc(sizeof(struct dcn10_ipp), GFP_KERNEL);
A lot of other headers also miss a direct include in this file,
but this is the only one that causes a problem for now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An initialization was added for two optional struct members. One of
these is always present in the dcn20_resource file, but the other one
depends on CONFIG_DRM_AMD_DC_DSC_SUPPORT and causes a build failure if
that is missing:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn20/dcn20_resource.c:926:14: error: excess elements in struct initializer [-Werror]
.num_dsc = 5,
Add another #ifdef around the assignment.
Fixes: c3d03c5a19 ("drm/amd/display: Include num_vmid and num_dsc within NV14's resource caps")
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid a compiler warning.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It seems always request passive flip on RN due to incorrect compare
clock state to determine optization.
[How]
Instead of calling memcmp, compare clock state member to determine the
condition.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When a timeout occurs after a DEFER, some devices require more retries
than in the case of a regular timeout.
[How]
In a timeout occurrence, check whether a DEFER has occurred before the
timeout and retry MAX_DEFER_RETRIES retries times instead of
MAX_TIMEOUT_RETRIES.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Value obtained from DV is not allowing 8k60 CTA mode with DSC to
pass, after checking real value being used in hw, find out that
correct value is 3600, which will allow that mode.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
During mode transition steer fifo could overflow. Quite often it
recovers by itself, but sometimes it doesn't.
[how]
Add steer fifo reset before unblanking the stream. Also add a short
delay when resetting dig resync fifo to make sure register writes
don't end up back-to-back, in which case the HW might miss the reset
request.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The variable mismatch assignment error.
[How]
To use uint32_t replace it.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP spec requires 1000 symbols delay between the end of link training
and enabling FEC in the stream. Currently we are using 1 miliseconds
delay which is not accurate.
[how]
One lane RBR should have the maximum time for transmitting 1000 LL
codes which is 6.173 us. So using 7 microseconds delay instead of
1 miliseconds.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new sr and pstate latencies are optimized for the case when we are not
using lpddr4 memory
[How]
have two different wm tables, one for the lpddr case and one for
non lpddr case
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dc_link_is_dp_sink_present, if dal_ddc_open fails, then
dal_gpio_destroy_ddc is called, destroying pin_data and pin_clock. They
are created only on dc_construct, and next aux access will cause a panic.
[How]
Instead of calling dal_gpio_destroy_ddc, call dal_ddc_close.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When video_memory_type bw_params->vram_type
is assigned, wedistinguish between Ddr4MemType and LpDdr4MemType.
Because of this we will never report that we are using
LpDdr4MemType and never re-purpose WM set D
[How]
populate bios integrated info for renoir by adding the
revision number for renoir and use that integrated info
table instead of of asic_id to get the vram type
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pstate_latency_us never gets updated from the hard coded value
in rn_clk_mgr.c
[how]
update the wm table's values before we do calculations with them
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On ASICs where number of DSCs is the same as OPPs there's no need
for DSC resource management. Mappping 1-to-1 fixes mode-set- or S3-
-related issues for such platforms.
[how]
Map DSC resources 1-to-1 to pipes only if number of OPPs is the same
as number of DSCs. This will still keep other ASICs working.
A follow-up patch to fix mode-set issues on those ASICs will be
required if testing shows issues with mode set.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized latency numbers.
[How]
Add sr latencies to the wm table, use different latencies
for different wm sets.
Also fix bb override from registery key for these latencies.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To quickly validate whether DMCUB is running and accepting commands for
offload testing we want to intercept a common sequence as part of
modeset programming.
[How]
OTG enable will cause the most impact in terms of golden register
changes and it's a single register write.
This approach was previously done in dcn10 code when it was shared with
dcn20 but it wasn't ported over to the dcn20 code.
Port over start, execute and wait sequence into dcn20_optc.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When setting lttpr mode, the new mode to bet is not logged properly.
[How]
Update log message to show the right mode.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation for further changes
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It seems always request passive flip on RN due to incorrect compare
clock state to determine optization.
[How]
Instead of calling memcmp, compare clock state member to determine the
condition.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When a timeout occurs after a DEFER, some devices require more retries
than in the case of a regular timeout.
[How]
In a timeout occurrence, check whether a DEFER has occurred before the
timeout and retry MAX_DEFER_RETRIES retries times instead of
MAX_TIMEOUT_RETRIES.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we require HDR_MULT >= 1.0
There are scenarios where we need < 1.0
[How]
Only guard against 0 - it will black-screen image.
It is up to higher-level logic to decide what HDR_MULT
values are allowed in each particular case.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need support for more color management in 10bit
surface.
[How]
Provide support for DePQ for 10bit surface
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Value obtained from DV is not allowing 8k60 CTA mode with DSC to
pass, after checking real value being used in hw, find out that
correct value is 3600, which will allow that mode.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor position needs to take into account plane scaling as well.
[How]
Translate cursor coords from stream space to plane space.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is causing green Line at the bottom of SDR 480p
MPO playback
[How]
Limit workaround to vertical > 512
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc needs to expose its internal dsc policy.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
add_dsc_to_stream_resource could be called for validation.
Failing validation is completely fine.
However failing it inside commit streams is bad.
This code could be triggered for both contexts.
The function itself cannot distinguish the caller, which
makes it impossible to output the log only in the
meaningful case (commit streams).
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to support 6 bpp for 420 pixel encoding only.
[how]
Add a dc function to determine what bpp range can be supported
for given pixel encoding.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
I was advised that we don't need this call of program_front_end, as
earlier and later calls in the same sequence are sufficient.
[How]
Remove first call of program_front_end in dc_commit_state_no_check.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
I was advised that we may need to check for mpcc idle in more cases
than just when opp_changed is true. Also, mpcc_inst is equal to
pipe_idx, so remove for loop.
[How]
Remove opp_changed flag check and mpcc_inst loop.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When training with repeater the aux read interval must be set to
repeater specific aux_red_interval. This value is always 100us for CR.
[How]
Check for repeater when setting the aux_rd_interval in channel
equalization.
Use the right offset in the aux_rd_interval array
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: George Shen <George.Shen@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MPCC programming was being missed during certain split pipe enables due
to full_update flag not being true. This caused a momentary flash on
half the screen. After discussion, determined we should not have that
flag check within update_mpcc, as it should always perform full
programming when called.
[How]
Remove flag check. We call update_blending within insert_plane, so we
do not need to replace its call from the if block.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized sr latency numbers, for lpddr4
[How]
change the sr laency in the lpddr4 wm table to the new latency
number
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Commands will be considered a stable ABI between driver and firmware.
Commands are also split between DC commands, DAL feature commands,
and VBIOS commands.
Commands are currently not designated to a specific ID and the enum
does not provide a stable ABI.
We currently group all of these into a single command type of 8-bits.
With the stable ABI consideration in mind it's not unreasonable to
run out of command IDs.
For cleaner separation and versioning split the commands into a main
type and a subtype.
[How]
For commands where performance matters (like reg sequences) these
are still considered main commands.
Sub commands will be split by ownership/feature.
Update existing command sequences to reflect new changes.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The function is expected to return instance of the timing generator
therefore we shouldn't be returning boolean in integer function,
and we shouldn't be returning zero so changing it to -1.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The link setting will be modify after disable phy
and due to DP Compliance Fails.
[How]
Save and resotre link setting for disable link phy when link retraining.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to know DP protocol version
[How]
In DC create we initialize a cap to indicate the max
DP protocol version supported
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized latency numbers, for lpddr4
[How]
change the p-state laency in the lpddr4 wm table to the new latency
number
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need support for more color management in 10bit
surface.
[How]
Provide support for DePQ for 10bit surface
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
During mode transition steer fifo could overflow. Quite often it
recovers by itself, but sometimes it doesn't.
[how]
Add steer fifo reset before unblanking the stream. Also add a short
delay when resetting dig resync fifo to make sure register writes
don't end up back-to-back, in which case the HW might miss the reset
request.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Bring this calculation in line with HW programming guide.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Previous Renoir chroma viewport workaround fixed an MPO flicker by
increasing the chroma viewport size. However, when the MPO plane is
rotated 180 degrees, the viewport is read in reverse. Since the workaround
increases viewport size, when reading in reverse it causes a vertical
chroma offset.
[HOW]
Pass rotation value to viewport set functions
Temporarily disable the chroma viewport w/a when hubp is rotated 180 degrees
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The variable mismatch assignment error.
[How]
To use uint32_t replace it.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP spec requires 1000 symbols delay between the end of link training
and enabling FEC in the stream. Currently we are using 1 miliseconds
delay which is not accurate.
[how]
One lane RBR should have the maximum time for transmitting 1000 LL
codes which is 6.173 us. So using 7 microseconds delay instead of
1 miliseconds.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before was using HW counter value to determine the dprefclk. Which
take into account ss, but has large variation, not good enough for
generating audio dto. Also, the bios parser code to get the ss
percentage was not working.
[How]
After this change, dprefclk is hard coded, same as on RV. We don't
expect this to change on Renoir. Modified bios parser code to get
the right ss percentage.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new sr and pstate latencies are optimized for the case when we are not
using lpddr4 memory
[How]
have two different wm tables, one for the lpddr case and one for
non lpddr case
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
