This patch adds Renesas R-Car USB phy driver.
It supports R8A7779 chip at this point.
R-Car has some USB controllers, but has only one phy-initializer.
So, this driver is counting users.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The exception is needed on big endian systems too.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need for a vendor specific probe exception just to
match on the interface class.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are many modems in addition to the D-Link DWM 652
exposing the CD interface in modem mode, and some expose
an integrated card reader as well. Always ignore these
interfaces.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1623) removes the ehci_port_power() routine and all the
places that call it. There's no reason for ehci-hcd to change the
port power settings; the hub driver takes care of all that stuff.
There is one exception: When the controller is resumed from
hibernation or following a loss of power, the ports that are supposed
to be handed over to a companion controller must be powered on first.
Otherwise the handover won't work. This process is not visible to the
hub driver, so it has to be handled in ehci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1622) removes the USB-2.1 Link Power Management code
from the ehci-hcd driver. This code was never integrated with
usbcore, it is full of bugs, and it was not getting used by anybody.
However, the debugging code for dumping the LPM-related fields in the
EHCI registers is left in place. In theory it might be useful to see
these values, even though we don't use them.
This essentially amounts to a partial revert of commit
aa4d834298 (USB: EHCI: EHCI 1.1
addendum: preparation) and an almost full revert of commit
48f2497014 (USB: EHCI: EHCI 1.1
addendum: Basic LPM feature support) plus its follow-ons.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1621) removes the limit on the number of loops allowed
in hub_tt_work(). The value is arbitrary, and it's silly to have a
limit in the first place -- anything beyond the limit would not get
handled.
Besides, it's most unlikely that we'll ever need to clear more than a
couple of TT buffers at any time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove all MODULE_VERSION macros and driver-version information (except
for garmin_gps which uses it in a status reply).
It is the kernel version that matters and not some private version
scheme which rarely even gets updated.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 16bit read access to MUSB_INTRTXE results in an 32bit read
access which also reads INTRRX and therefore may lose interrupts.
This patch uses a shadow register of MUSB_INTRTXE so we only perform
write access to it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 16bit read access to MUSB_INTRRXE results in an 32bit read
access which also reads INTRUSB and therefore may lose interrupts.
This patch uses a shadow register of MUSB_INTRRXE so we only perform
write access to it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 8bit read access to FADDR results in an 32bit read
access which also reads INTRTX and therefore may lose interrupts.
This patch removes any reads to FADDR as they are not really required.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 8bit read access to MUSB_POWER results in an 32bit read
access which also reads INTRTX and therefore may lose interrupts.
This patch tries to minimize reads to MUSB_POWER and perform them only
when required.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The lockless implementation of the unique id is quite impressive (:P)
but dirver's core can handle it, we can remove it and make our code a
little smaller.
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The one thing that makes two UDCs+HCDs impossible is the global
the_controller variable. This patch changes this. After device
allocation we allocate the "the_controller" variable and pass it as
platform_data to the UDC and its companion.
We can have now multiple instances dummy hcd and therefore I change the
limit from one to two. I was able to test this with g_ncm adn g_zero:
|# lsusb
|Bus 001 Device 002: ID 0525:a4a0 Netchip Technology, Inc. Linux-USB "Gadget Zero"
|Bus 002 Device 002: ID 0525:a4a1 Netchip Technology, Inc. Linux-USB Ethernet Gadget
|Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
|Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
I was able to start testusb -a and ifconfig usb[01] up with no complains.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch creates & adds multiple instances of the HCD and UDC. We have
a new module option "num" which says how many emulated UDCs + HCDs we
want. The default value is one and currently the maximum is one as well.
This will change soon.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch replaces the single pdev variable by an array. One change:
The device id is no longer -1 (i.e. none) but 0.
This is prepation work for multiple instances of the dummy_hcd + udc
which should help to test gadget framework with multiple UDCs.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of calling usb_string_id() multiple times I replace it with one
usb_string_ids_tab(). The NULL pointer in struct usb_string with "" and
are not overwritten in fail or unbind case.
The conditional assignment remains because some gadgets recycle the string
ID because the same descriptor (and string ID) is used if we have more
than one config descriptor.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is no need for this variable in between.
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the shifting and masking of interface and its alt
setting and provides its own variable.
This looks better and is smaller:
text data bss dec hex filename
x86-32
6940 956 56 7952 1f10 gadget/audio.o.old
6908 956 56 7920 1ef0 gadget/audio.o.new
arm
7914 956 56 8926 22de gadget/audio.o.old
7886 956 56 8898 22c2 gadget/audio.o.new
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DMA_ADDR_INVALID is used by the UDC driver and the gadgets should
provide only a buffer address. Everything else should be taken core of
by the UDC and udc-core.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
HS and SS descriptors are staticaly created. They are updated during the
bind process with the endpoint address, string id or interface numbers.
After that, the descriptor chain is linked to struct usb_function which
is used by composite in order to serve the GET_DESCRIPTOR requests,
number of available configs and so on.
There is no need to assign the HS descriptor only if the UDC supports
HS speed because composite won't report those to the host if HS support
has not been reached. The same reasoning is valid for SS.
This patch makes sure each function updates HS/SS descriptors
unconditionally and uses the newly introduced helper function to create a
copy the descriptors for the speed which is supported by the UDC.
While at that, also rename f->descriptors to f->fs_descriptors in order
to make it more explicit what that means.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The "video->minor = -1" assigment is done in V4L2 by
video_register_device() so it is removed here.
Now. uvc_function_bind() calls in error case uvc_function_unbind() for
cleanup. The problem is that uvc_function_unbind() frees the uvc struct
and uvc_bind_config() does as well in error case of usb_add_function().
Removing kfree() in usb_add_function() would make the patch smaller but
it would look odd because the new allocated memory is not cleaned up.
However it is not guaranteed that if we call usb_add_function() we also
get to the bind function.
Therefore the patch extracts the conditional cleanup from
uvc_function_unbind() applies to uvc_function_bind().
uvc_function_unbind() now contains only the complete cleanup which is
required once everything has been registrated.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This function works only on FS or HS. If the gadget is HS capable only
HS descriptors are assigned. If we plug it to an 1.1 host it won't work
because we have only 2.0 descriptors. This patch changes the behavior to
provide both sets.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The HS descriptors are only created if HS is supported by the UDC but we
never free them.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whether highspeed configuration is valid or not is something that
composite decides and not the gadget. That gadget can only provide the
required descriptors for it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
I think this is wrong since 72c973dd ("usb: gadget: add
usb_endpoint_descriptor to struct usb_ep"). If we fail to allocate an ep
or bail out early we shouldn't check for the descriptor which is
assigned at ep_enable() time.
Cc: Tatyana Brokhman <tlinder@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case something goes wrong here, don't leak memory / endpoints.
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The 9 for HS means 32ms. Use the macro to make it easier to read.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The 5+4 magic for HS tries to aim 32ms which is also what is intended
with 1 << 5 for FS. This little macro should make this easier to
understand.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The descriptor list for FS speed was not NULL terminated. This patch
fixes this.
While here one of the twe two bAlternateSetting assignments for the BOT
interface. Both assign 0, one is enough.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit d11519 ("usb: gadget: Add Interface Association Descriptor to
ECM") added the IAD descriptor to FS and HS descriptors. The SS
descriptor has been left out probably because it has been added "just
recently".
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch enabled dma mapping, and used dma transfer handler
on mod_host
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
mod.h has irq_bempsts/irq_brdysts to keep each irq status,
but it was difficult to find where they were used
on renesas_usbhs driver by using "grep irq_xxxx" command,
since it used irq_##status macro.
This patch fixup them
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch uses devm_request_irq() instead of request_irq(),
and removed free_irq() from driver
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When rts51x_read_status() returns USB_STOR_TRANSPORT_ERROR,
an error happens. This patch fixes build warning as below:
drivers/usb/storage/realtek_cr.c: In function 'init_realtek_cr':
drivers/usb/storage/realtek_cr.c:476:33: warning: 'buf[15]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[15]' was declared here
drivers/usb/storage/realtek_cr.c:475:33: warning: 'buf[14]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[14]' was declared here
drivers/usb/storage/realtek_cr.c:474:50: warning: 'buf[13]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[13]' was declared here
drivers/usb/storage/realtek_cr.c:472:30: warning: 'buf[12]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[12]' was declared here
drivers/usb/storage/realtek_cr.c:471:31: warning: 'buf[11]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[11]' was declared here
drivers/usb/storage/realtek_cr.c:470:31: warning: 'buf[10]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[10]' was declared here
drivers/usb/storage/realtek_cr.c:469:30: warning: 'buf[9]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[9]' was declared here
drivers/usb/storage/realtek_cr.c:468:27: warning: 'buf[8]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[8]' was declared here
drivers/usb/storage/realtek_cr.c:468:43: warning: 'buf[7]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[7]' was declared here
drivers/usb/storage/realtek_cr.c:467:30: warning: 'buf[6]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[6]' was declared here
drivers/usb/storage/realtek_cr.c:466:30: warning: 'buf[5]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[5]' was declared here
drivers/usb/storage/realtek_cr.c:465:28: warning: 'buf[4]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[4]' was declared here
drivers/usb/storage/realtek_cr.c:464:24: warning: 'buf[3]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[3]' was declared here
drivers/usb/storage/realtek_cr.c:464:40: warning: 'buf[2]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[2]' was declared here
drivers/usb/storage/realtek_cr.c:463:24: warning: 'buf[1]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[1]' was declared here
drivers/usb/storage/realtek_cr.c:463:40: warning: 'buf[0]' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/storage/realtek_cr.c:455:5: note: 'buf[0]' was declared here
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use ftdi_get_modem_status to check hardware buffers in chars_in_buffer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to check hardware buffers when we know that the software
buffers are non-empty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use generic chars_in_buffer rather than copying it's implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export generic chars_in_buffer implementation so it can be used in
subdrivers in combination with checks of any hardware buffers.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we do not return USB-internal error codes to userspace.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Align the modem-control status operands as was originally indented.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unused port field from private port data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there's no possible caller of dbgp_external_startup() and
dbgp_reset_prep() when !USB_EHCI_HCD, there's no point in building and
exporting these functions in that case. This eliminates a build error
under the conditions listed in the subject, introduced with the merge
f1c6872e49.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there's no possible caller of dbgp_external_startup() and
dbgp_reset_prep() when !USB_EHCI_HCD, there's no point in building and
exporting these functions in that case. This eliminates a build error
under the conditions listed in the subject, introduced with the merge
f1c6872e49.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we do not allocate urbs if we do not have a bulk endpoint.
Legacy code used incorrect assumption to test for bulk endpoints.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're reverting MUSB Mode 1 DMA patch which caused many regressions. Meanwhile
Roger is cooking a better version of that patch, which will hopefully be ready
for v3.8 merge window.
We also fix an undeclared error in ux5000_remove() and another build error
when we try to build USB_MUSB_OMAP2PLUS as a module.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=caV/
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
usb: fixes for v3.7-rc4
We're reverting MUSB Mode 1 DMA patch which caused many regressions. Meanwhile
Roger is cooking a better version of that patch, which will hopefully be ready
for v3.8 merge window.
We also fix an undeclared error in ux5000_remove() and another build error
when we try to build USB_MUSB_OMAP2PLUS as a module.
TWL4030_USB & TWL6030_USB must depend on USB_MUSB_OMAP2PLUS in Kconfig else
we get build errors with
CONFIG_USB_MUSB_HDRC=m
CONFIG_USB_MUSB_OMAP2PLUS=m
CONFIG_TWL4030_USB=y
CONFIG_TWL6030_USB=y
LD init/built-in.o
drivers/built-in.o: In function `twl4030_usb_irq':
drivers/usb/otg/twl4030-usb.c:518: undefined reference to `omap_musb_mailbox'
drivers/built-in.o: In function `twl4030_usb_phy_init':
drivers/usb/otg/twl4030-usb.c:540: undefined reference to `omap_musb_mailbox'
drivers/built-in.o: In function `twl6030_usb_irq':
drivers/usb/otg/twl6030-usb.c:230: undefined reference to `omap_musb_mailbox'
drivers/usb/otg/twl6030-usb.c:225: undefined reference to `omap_musb_mailbox'
drivers/built-in.o: In function `twl6030_usbotg_irq':
drivers/usb/otg/twl6030-usb.c:259: undefined reference to `omap_musb_mailbox'
CC: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This pulls in all of the USB changes in 3.7-rc3 into usb-next and
resolves the merge issue with:
drivers/usb/misc/ezusb.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65b3d52d02
(usb: musb: add musb_ida for multi instance support)
used musbid in ux500_remove() but nerver declared it.
I found this in x86_64 platform, but not sure whether
this is a error on the correct ARCH.
$ make drivers/usb/musb/ux500.o
make[1]: Nothing to be done for `all'.
make[1]: Nothing to be done for `relocs'.
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
UPD include/generated/utsrelease.h
CALL scripts/checksyscalls.sh
CC drivers/usb/musb/ux500.o
drivers/usb/musb/ux500.c: In function 'ux500_probe':
drivers/usb/musb/ux500.c:78:2: error: 'musbid' undeclared (first use in this function)
drivers/usb/musb/ux500.c:78:2: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [drivers/usb/musb/ux500.o] Error 1
make: *** [drivers/usb/musb/ux500.o] Error 2
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 4f3e8d263d.
it turns out that current implementation of Mode 1
DMA added a few regressions to some users, so we
need to revert this patch and let author work on
a better version of Mode 1 DMA support.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove the variable ep_ctx from xhci_add_endpoint(), since it is
assigned but unused. Caught by Coverity.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Remove the variable slot_ctx from xhci_dbg_ctx(), since it is assigned
but unused. Caught by Coverity.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Coverity complains that xhci_evaluate_context_result() is missing a
break statement after the COMP_EBADSLT switch case. It's not a big
deal, since we wanted to return the same error code as the case
statement below it does. The end result would be one that a Slot
Disabled error completion code would also print the warning message
associated with a Context State error code. No other bad behavior would
result.
It's not worth backporting to stable kernels, since it only fixes an
issue with too much debugging.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The command cancellation code doesn't check whether find_trb_seg()
couldn't find the segment that contains the TRB to be canceled. This
could cause a NULL pointer deference later in the function when next_trb
is called. It's unlikely to happen unless something is wrong with the
command ring pointers, so add some debugging in case it happens.
This patch should be backported to stable kernels as old as 3.0, that
contain the commit b63f4053cc "xHCI:
handle command after aborting the command ring".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch sets hub device's default autosuspend delay as 0 to
speedup bus suspend, see comments in code for details.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hub status endpoint has a long 'bInterval', which is 255ms
for FS/LS device and 256ms for HS device according to USB 2.0 spec,
so the device connection change may be reported later more than 255ms
via status pipe.
The connection change in hub may have been happened already on the
downstream ports, but no status URB completes when it is killed
in hub_suspend(auto), so the connection change may be missed by some
buggy hub devices, which won't generate remote wakeup signal after
their remote wakeup is enabled and they are put into suspend state.
The problem can be observed at least on the below Genesys Logic, Inc.
hub devices:
0x05e3,0x0606
0x05e3,0x0608
In theory, there is no way to fix the problem completely, but we
can make it less likely to occur by this patch.
This patch introduces one quirk of HUB_QUIRK_CHECK_PORTS_AUTOSUSPEND
to check ports' change during hub_suspend(auto) for the buggy
devices. If ports' change is found, terminate the auto suspend and
return to working state.
So for the buggy hubs, if the connection change happend before
the ports' check, it can be handled correctly. If it happens between
the ports' check and enabling remote wakeup/entering suspend, it
will be missed. Considered the interval is quite short, it is very
less likely to happen during the window.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BIOS vendors keep changing the BIOS versions. Only match the beginning
of the string to match all Lucid tablets with board name M11JB.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove temporary do-while(0) loop used to keep changes minimal.
Fixup indentation, remove some line breaks, and replace break with goto
to maintain flow.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the indentation was kept intact using a do-while(0) in order
to facilitate review. A follow-up patch will remove it.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove private zombie flag used to signal disconnect and to prevent
control urb from being submitted from interrupt urb completion handler.
The control urb will not be re-submitted as both the control urb and the
interrupt urb is killed on disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The private int_urb is never allocated so the submission from the
control completion handler will always fail. Remove this odd piece of
broken code.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does not wait until the hardware buffer (for data from the PC to the
UART line) is drained when tcdrain or close is called in an application.
Solution: Implement a chars_in_buffer function that checks both the software
and hardware buffer. If the TEMT (TX empty) bit of the line status register
indicates the hw buffer is not empty, let the function return at least 1. This
has been verified to work correctly with an FT232RL. The check on the hw buffer
can not be done for the original SIO device.
Signed-off-by: Jarkko Huijts <jarkko.huijts@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move interface data allocation to attach so that it is deallocated
should usb-serial probe fail.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move interface data allocation to attach so that it is deallocated
should usb-serial probe fail.
Note that the usb device id is stored at probe so that it can be used
in attach to determine send-setup blacklisting.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move interface data allocation to attach so that it is deallocated
should usb-serial probe fail.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver set the usb-serial port pointers to NULL on errors in attach,
effectively preventing usb-serial core from decrementing the port ref
counters and releasing the port devices and associated data.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure control urb is freed at release.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note also that urb-count for multi-port interfaces has not been changed
even though the usb-serial port number is now determined from the port
and interface minor numbers.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move interface data allocation to attach so that it is deallocated on
errors in usb-serial probe.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure port private data is deallocated on errors in attach.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak in usb-serial probe error path by moving port
data allocation to port_probe.
Since commit a1028f0abf ("usb: usb_wwan: replace release and disconnect
with a port_remove hook") port data is deallocated in port_remove. This
leaves a possibility for memory leaks if usb-serial probe fails after
attach but before the port in question has been successfully registered.
Note that this patch also fixes two additional memory leaks in the error
path of attach should port initialisation fail for any port as the urbs
were never freed and neither was the data of any of the successfully
initialised ports.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix NULL-pointer dereference at release by moving port data allocation
and deallocation to port_probe and port_remove.
Fix NULL-pointer dereference at disconnect by stopping port urbs at
port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer accessible at
disconnect or release.
Note that this patch also fixes port and interface-data memory leaks in
the error path of attach should port initialisation fail for any port.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure generic close is called at close.
The driver relies on the generic write implementation but did not call
generic close.
Note that the call to kill the read urb is not redundant, as mct_u232
uses an interrupt urb from the second port as the read urb and that
generic close therefore fails to kill it.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to allocate the control-message buffer dynamically as some
platforms cannot do DMA from stack.
Note that only the first byte of the old buffer was used.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure no control urb is submitted during close after a disconnect by
checking the disconnected flag.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill urbs unconditionally at close and disconnect.
Note that URB status is not valid outside of completion handler.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that this also fixes memory leaks in the error path of attach where
the write urbs were not freed on errors.
Make sure all interface-data deallocation is done in release by moving
the read urb deallocation from disconnect.
Note that the write urb is killed during close so that the call in
disconnect was superfluous.
Compile-only tested.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix memory leak in attach error path where the read urb was never freed.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that this patch also fixes a second port-data memory leak in the
error path of attach, should parallel-port initialisation fail.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the oob port is never registered as a port device and should
thus be handled in attach and release.
Compile-only tested.
Cc: Peter Berger <pberger@brimson.com>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation to port_probe
and actually implementing deallocation.
Note that this driver has never even bothered to try to deallocate it's
port data...
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the fifth port (command port) is never registered as a
port device and thus should be handled in attach and release.
Compile-only tested.
Cc: <support@connecttech.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure command buffer is deallocated in case of errors during attach.
Cc: <support@connecttech.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure no control urb is submitted during close after a disconnect by
checking the disconnected flag.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the call to metrousb_clean (close) in shutdown was redundant.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1620) speeds up USB root-hub resumes in the common case
where every enabled port has its suspend feature set (which currently
will be true for every runtime resume of the root hub). If all the
enabled ports are suspended then resuming the root hub won't resume
any of the downstream devices. In this case there's no need for a
Resume Recovery delay, because that delay is meant to give devices a
chance to get ready for active use.
To keep track of the port suspend features, the patch adds a
"port_is_suspended" flag to struct usb_device. This has to be tracked
separately from the device's state; it's entirely possible for a USB-2
device to be suspended while the suspend feature on its parent port is
clear. The reason is that devices will go into suspend whenever their
parent hub does.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1619) improves the interface to the "hub_for_each_child"
macro. The name clearly suggests that the macro iterates over child
devices; it does not suggest that the loop will also iterate over
unnconnected ports.
The patch changes the macro so that it will skip over unconnected
ports and iterate only the actual child devices. The two existing
call sites are updated to avoid testing for a NULL child pointer,
which is now unnecessary.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for splitting the ehci-hcd driver into a core library
and separate platform-specific driver modules, this patch (as1618)
moves ehci_update_device() from a couple of platform-specific source
files into ehci-lpm.c. This is where it should have been all along,
since all it does is call a couple of other functions that are already
in ehci-lpm.c.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for splitting the ehci-hcd driver into a core library
and separate platform-specific driver modules, this patch (as1617)
changes the way ehci_read_frame_index() is handled.
Since the same core library will have to work with both PCI and
non-PCI platforms, the quirk handler routine will be compiled
unconditionally. The decision about whether to call it or simply to
read the frame index register is made at run time, based on whether
the frame_index_bug quirk flag is set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for splitting the ehci-hcd driver into a core library
and separate platform-specific driver modules, this patch (as1616)
moves the console logging macros from ehci-dbg.c to ehci.h, where they
will be available to the platform drivers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this condition, all controllers will do this delay,
and increase the resume time.
Only enabled and unsuspended port needs this delay, but
Some buggy hardware(like Synopsys usb controller) will
clear suspend bit once they receive/send resume signal,
so it takes resume bit as consideration.
Tested it at Freescale i.mx6q Sabrelite board.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing compilaton error.
Incrementing usage counter only on successful execution of skel_open.
Removing redundant locking
Some last changes in function skel_open and finally commit
52a7499 Revert "USB: usb-skeleton.c: fix open/disconnect race"
introduced a bug in function skel_open, which this patch fixes.
Changes since v2:
- refactoring
- Removing redundant mutex synchronization.
Changes since v1:
- Fixed accordingly feedback of Oliver Neukum oneukum@suse.de: also need to drop the lock.
Signed-off-by: Constantine Shulyupin <const@MakeLinux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We defined bus_to_hdc for that, use it.
Signed-off-by: Yuanhan Liu <yliu.null@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_ functions allocate memory that is released when a driver
detaches. This patch uses devm_clk_get() for these functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Almost nothing from this file is used, and the file will hopefully be
deleted soon. Copy the tiny portions that are used directly into
tegra_usb_phy.c. I believe that Venu Byravarasu is working on cleaning up
our USB driver, and those cleanups will remove the need for these
constants.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Almost nothing from this file is used, and the file will hopefully be
deleted soon. Copy the tiny portions that are used directly into
ehci-tegra.c. I believe that Venu Byravarasu is working on cleaning up
our USB driver, and those cleanups will remove the need for these
constants.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ezusb code was split out, support was added for the fx2 chip
type, but no one is using these functions, so comment it out. If
someone needs it, it can be added back in the future.
Also properly include <linux/usb/ezusb.h> into the ezusb.c file, to
ensure we catch any function prototype mis-matches
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I found a memory leak in sierra_release() (well sierra_probe() I guess)
that looses 8 bytes each time the driver releases a device.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
flush_work_sync and flush_work are now the same and flush_work_sync
has been deprecated. This fixes the following warning:
drivers/usb/core/hub.c: In function hub_quiesce:
drivers/usb/core/hub.c:1216:3: warning: flush_work_sync is deprecated (declared at include/linux/workqueue.h:448) [-Wdeprecated-declarations]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's four bug fixes for 3.7.
The first patch fixes a potential deadlock in the USB port power off code,
and the last two patches fix bugs in the USB 3.0 Link PM patchset. The
second one is trivial and removes an unnecessary cast.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=W4Wk
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-10-23' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
xHCI fixes for 3.7-rc3
Hi Greg,
Here's four bug fixes for 3.7.
The first patch fixes a potential deadlock in the USB port power off code,
and the last two patches fix bugs in the USB 3.0 Link PM patchset. The
second one is trivial and removes an unnecessary cast.
Sarah Sharp
Here's a new set of fixes for v3.7-rc3. It's quite small, only
four patches.
There's one bug fix for the newly added musb-dsps glue layer where
we could be overflowing a buffer when creating the instance name.
NET2272 got a fix for a case where the lock would be left held
when exiting the IRQ handler with error in case of Spurious IRQs.
Renensas USBHS got a DMA stall fix which would cause transfers to
stall forever and a NULL pointer deref fix in case of pipe detach.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=smxQ
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
usb: fixes for v3.7-rc3
Here's a new set of fixes for v3.7-rc3. It's quite small, only
four patches.
There's one bug fix for the newly added musb-dsps glue layer where
we could be overflowing a buffer when creating the instance name.
NET2272 got a fix for a case where the lock would be left held
when exiting the IRQ handler with error in case of Spurious IRQs.
Renensas USBHS got a DMA stall fix which would cause transfers to
stall forever and a NULL pointer deref fix in case of pipe detach.
xhci_service_interval_to_ns() returns long long
to avoid an overflow. However, the type cast happens
too late. The fix is to force ULL from the beginning.
This patch should be backported to kernels as old as 3.5, that contain
the commit e3567d2c15 "xhci: Add Intel
U1/U2 timeout policy."
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: stable@vger.kernel.org
An le16 is accessed without conversion.
This patch should be backported to kernels as old as 3.5, that contain
the commit e3567d2c15 "xhci: Add Intel
U1/U2 timeout policy."
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: stable@vger.kernel.org
Commit cfa49b4b (USB: ohci: merge ohci_finish_controller_resume with
ohci_resume) merged ohci_finish_controller_resume with ohci_resume but forgot
to update the ohci-sm501 driver accordingly, thus causing the folllowing build
failure:
drivers/usb/host/ohci-sm501.c: In function 'ohci_sm501_resume':
drivers/usb/host/ohci-sm501.c:241:2: error: implicit declaration of function
'ohci_finish_controller_resume' [-Werror=implicit-function-declaration]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
renesas_usbhs driver can switch DMA/PIO transfer by using handler,
and each handler have push/pop direction.
But unfortunately, current dma push handler didn't a path
which calls usbhs_pipe_enable(). Thus, dma transfer never happened.
this patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If renesas_usbhs or DMAEngine interrupt didn't happen by a certain cause,
urb->ep will be NULL by usb time out.
Then, host mode will access to it and crash kernel.
This patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add the missing unlock on the error handle path in function
net2272_irq().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The res_name is used for the name construction of a DT property as
follows:
sprintf(res_name, "port%d-mode", id);
Hence, res_name must be at least 11 characters long in order to store
the name including the terminating '\0'.
While at it, use to snprintf() rather than sprintf() when accessing this
buffer.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Struct usb_hub_descriptor.ss.DeviceRemovable has been defined as __le16
and (__force__ __u16) doesn't need.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When setting usb port's acpi power resource, there will be some xhci hub requests.
This will cause dead lock since xhci->lock has been held before setting acpi power
resource in the xhci_hub_control(). The usb_acpi_power_manageable() function might
fall into sleep so release xhci->lock before invoking it.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The "wusb_cap_descr_default" is never used. GCC doesn't complain about
it because we have that line ".bLength = sizeof(wusb_cap_descr_default)"
inside the definition itself. Clang complains though.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the ohci-platform driver to use the device managed helper
function for requesting memory region and ioremapping memory resources.
As a result the error path in the probe function is simplified, and the
platform driver remove callback does no longer need to release and iounmap
memory resources. devm_request_and_ioremap() will use either the ioremap()
or ioremap_nocache() handler depending on the resource's CACHEABLE flag, so
we are good with this change.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the ehci-platform driver to use the device managed helper
function for requesting memory region and ioremapping memory resources.
As a result the error path in the probe function is simplified, and the
platform driver remove callback does no longer need to release and iounmap
memory resources. devm_request_and_ioremap() will use either the ioremap()
or ioremap_nocache() handler depending on the resource's CACHEABLE flag, so
we are good with this change.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We meant to write "resource" instead of "recourse", this patch fixes this
typo.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the obvious typo in the error message, we meant to write "resource"
instead of "recourse".
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts the ohci-platform driver to use dev_err() functions
instead of pr_err().
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts the ehci-platform driver to make use of the dev_err()
functions instead of pr_err().
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A previous patch converted the Alchemy platform to use the OHCI and EHCI
platform drivers. As a result, all the common logic to handle USB present in
drivers/usb/host/alchemy-common.c has no reason to remain here, so we move it
to arch/mips/alchemy/common/usb.c which is a more appropriate place. This
change was suggested by Manuel Lauss.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All users have been converted to use the OHCI platform driver instead, thus
making ohci-au1xxx obsolete, remove it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All users have been converted to use the OHCI platform driver instead, thus
making ohci-sh obsolete, so remove it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All users have been converted to use the OHCI platform driver instead, thus
making ohci-xls obsolete, remove it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All users have been converted to use the OHCI platform driver instead, thus
making ohci-cns3xxx, so remove it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The users have been converted to use the platform OHCI driver instead, thus
making the ohci-pnx8550 driver obsolete, so remove it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge ohci_finish_controller_resume with ohci_resume as suggested by Alan
Stern. Since ohci_finish_controller_resume no longer exists, update the
various OHCI drivers to call ohci_resume() instead. Some drivers used to set
themselves the bit HCD_FLAG_HW_ACCESSIBLE, which is now handled by
ohci_resume().
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As suggested by Alan Stern, the code checking for the OHCI RH already
suspended is no longer required since the bug it fixes has not been seen in
ages. Remove that check making ohci_suspend much simpler.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
