This patch provides generic DSA code for using VLAN (802.1Q) tags for
the same purpose as a dedicated switch tag for injection/extraction.
It is based on the discussions and interest that has been so far
expressed in https://www.spinics.net/lists/netdev/msg556125.html.
Unlike all other DSA-supported tagging protocols, CONFIG_NET_DSA_TAG_8021Q
does not offer a complete solution for drivers (nor can it). Instead, it
provides generic code that driver can opt into calling:
- dsa_8021q_xmit: Inserts a VLAN header with the specified contents.
Can be called from another tagging protocol's xmit function.
Currently the LAN9303 driver is inserting headers that are simply
802.1Q with custom fields, so this is an opportunity for code reuse.
- dsa_8021q_rcv: Retrieves the TPID and TCI from a VLAN-tagged skb.
Removing the VLAN header is left as a decision for the caller to make.
- dsa_port_setup_8021q_tagging: For each user port, installs an Rx VID
and a Tx VID, for proper untagged traffic identification on ingress
and steering on egress. Also sets up the VLAN trunk on the upstream
(CPU or DSA) port. Drivers are intentionally left to call this
function explicitly, depending on the context and hardware support.
The expected switch behavior and VLAN semantics should not be violated
under any conditions. That is, after calling
dsa_port_setup_8021q_tagging, the hardware should still pass all
ingress traffic, be it tagged or untagged.
For uniformity with the other tagging protocols, a module for the
dsa_8021q_netdev_ops structure is registered, but the typical usage is
to set up another tagging protocol which selects CONFIG_NET_DSA_TAG_8021Q,
and calls the API from tag_8021q.h. Null function definitions are also
provided so that a "depends on" is not forced in the Kconfig.
This tagging protocol only works when switch ports are standalone, or
when they are added to a VLAN-unaware bridge. It will probably remain
this way for the reasons below.
When added to a bridge that has vlan_filtering 1, the bridge core will
install its own VLANs and reset the pvids through switchdev. For the
bridge core, switchdev is a write-only pipe. All VLAN-related state is
kept in the bridge core and nothing is read from DSA/switchdev or from
the driver. So the bridge core will break this port separation because
it will install the vlan_default_pvid into all switchdev ports.
Even if we could teach the bridge driver about switchdev preference of a
certain vlan_default_pvid (task difficult in itself since the current
setting is per-bridge but we would need it per-port), there would still
exist many other challenges.
Firstly, in the DSA rcv callback, a driver would have to perform an
iterative reverse lookup to find the correct switch port. That is
because the port is a bridge slave, so its Rx VID (port PVID) is subject
to user configuration. How would we ensure that the user doesn't reset
the pvid to a different value (which would make an O(1) translation
impossible), or to a non-unique value within this DSA switch tree (which
would make any translation impossible)?
Finally, not all switch ports are equal in DSA, and that makes it
difficult for the bridge to be completely aware of this anyway.
The CPU port needs to transmit tagged packets (VLAN trunk) in order for
the DSA rcv code to be able to decode source information.
But the bridge code has absolutely no idea which switch port is the CPU
port, if nothing else then just because there is no netdevice registered
by DSA for the CPU port.
Also DSA does not currently allow the user to specify that they want the
CPU port to do VLAN trunking anyway. VLANs are added to the CPU port
using the same flags as they were added on the user port.
So the VLANs installed by dsa_port_setup_8021q_tagging per driver
request should remain private from the bridge's and user's perspective,
and should not alter the VLAN semantics observed by the user.
In the current implementation a VLAN range ending at 4095 (VLAN_N_VID)
is reserved for this purpose. Each port receives a unique Rx VLAN and a
unique Tx VLAN. Separate VLANs are needed for Rx and Tx because they
serve different purposes: on Rx the switch must process traffic as
untagged and process it with a port-based VLAN, but with care not to
hinder bridging. On the other hand, the Tx VLAN is where the
reachability restrictions are imposed, since by tagging frames in the
xmit callback we are telling the switch onto which port to steer the
frame.
Some general guidance on how this support might be employed for
real-life hardware (some comments made by Florian Fainelli):
- If the hardware supports VLAN tag stacking, it should somehow back
up its private VLAN settings when the bridge tries to override them.
Then the driver could re-apply them as outer tags. Dedicating an outer
tag per bridge device would allow identical inner tag VID numbers to
co-exist, yet preserve broadcast domain isolation.
- If the switch cannot handle VLAN tag stacking, it should disable this
port separation when added as slave to a vlan_filtering bridge, in
that case having reduced functionality.
- Drivers for old switches that don't support the entire VLAN_N_VID
range will need to rework the current range selection mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all drivers can be probed using more traditional methods,
remove the legacy probe code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since different types of hardware may or may not support this setting
per-port, DSA keeps it either in dsa_switch or in dsa_port.
While drivers may know the characteristics of their hardware and
retrieve it from the correct place without the need of helpers, it is
cumbersone to find out an unambigous answer from generic DSA code.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current behavior is not as obvious as one would assume (which is
that, if the driver set vlan_filtering_is_global = 1, then checking any
dp->vlan_filtering would yield the same result). Only the ports which
are actively enslaved into a bridge would have vlan_filtering set.
This makes it tricky for drivers to check what the global state is.
So fix this and make the struct dsa_switch hold this global setting.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some switches, the action of whether to parse VLAN frame headers and use
that information for ingress admission is configurable, but not per
port. Such is the case for the Broadcom BCM53xx and the NXP SJA1105
families, for example. In that case, DSA can prevent the bridge core
from trying to apply different VLAN filtering settings on net devices
that belong to the same switch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows drivers to query the VLAN setting imposed by the bridge
driver directly from DSA, instead of keeping their own state based on
the .port_vlan_filtering callback.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that tag drivers dynamically register, we don't need the static
table. Remove it. This also means the tag driver structures can be
made static.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A DSA tag driver module will need to register the tag protocols it
implements with the DSA core. Add macros containing this boiler plate.
The registration/unregistration code is currently just a stub. A Later
patch will add the real implementation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Fix indent of #endif
Rewrite to move list pointer into a new structure
v3
Move kdoc next to macro
Fix THIS_MODULE indentation
Signed-off-by: David S. Miller <davem@davemloft.net>
In order that we can match the tagging protocol a switch driver
request to the tagger, we need to know what protocol the tagger
supports. Add this information to the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
More tag protocol to end of structure to keep hot members at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the tag drivers become modules, we will need to dynamically load
them based on what the switch drivers need. Add aliases to map between
the TAG protocol and the driver.
In order to do this, we need the tag protocol number as something
which the C pre-processor can stringinfy. Only the compiler knows the
value of an enum, CPP cannot use them. So add #defines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than keep a list to map a tagger ops to a name, place the name
into the ops structure. This removes the hard coded list, a step
towards making the taggers more dynamic.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2:
Move name to end of structure, keeping the hot entries at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
Before creating a slave netdevice, get the mac address from DTS and
apply in case it is valid.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ9893 switch is similar to KSZ9477 switch except the ingress tail tag
has 1 byte instead of 2 bytes. The size of the portmap is smaller and
so the override and lookup bits are also moved.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux bridge implementation allows various properties of the bridge
to be controlled, such as flooding unknown unicast and multicast frames.
This patch adds the necessary DSA infrastructure to allow the Linux
bridge support to control these properties for DSA switches.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[florian: Add missing dp and ds variables declaration to fix build]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having net/dsa.h contain both the internal switch tree/driver
structures, split the relevant platform_data parts into
include/linux/platform_data/dsa.h and make that header be included by
net/dsa.h in order not to break any setup. A subsequent set of patches
will update code including net/dsa.h to include only the platform_data
header.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is not currently way to infer the port number through sysfs that
is being used as the CPU port number. Overlay a ndo_get_phys_port_name()
operation onto the DSA master network device in order to retrieve that
information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each DSA tag protocol needs to add additional headers to the Ethernet
frame in order to direct it towards a specific switch egress port. It
must also remove the head from a frame received from a
switch. Indicate the maximum size of these headers in the tag protocol
ops structure, so the core can take these overheads into account.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This handles the tag added by the PMAC on the VRX200 SoC line.
The GSWIP uses internally a GSWIP special tag which is located after the
Ethernet header. The PMAC which connects the GSWIP to the CPU converts
this special tag used by the GSWIP into the PMAC special tag which is
added in front of the Ethernet header.
This was tested with GSWIP 2.1 found in the VRX200 SoCs, other GSWIP
versions use slightly different PMAC special tags.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We avoid 2 VLAs by using a pre-allocated field in dsa_switch. We also
try to avoid dynamic allocation whenever possible (when using fewer than
bits-per-long ports, which is the common case).
Link: http://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Link: http://lkml.kernel.org/r/20180505185145.GB32630@lunn.ch
Signed-off-by: Salvatore Mesoraca <s.mesoraca16@gmail.com>
[kees: tweak commit subject and message slightly]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for PHYLINK within the DSA subsystem in order to support more
complex devices such as pluggable (SFP) and non-pluggable (SFF) modules, 10G
PHYs, and traditional PHYs. Using PHYLINK allows us to drop some amount of
complexity we had while probing fixed and non-fixed PHYs using Device Tree.
Because PHYLINK separates the Ethernet MAC/port configuration into different
stages, we let switch drivers implement those, and for now, we maintain
functionality by calling dsa_slave_adjust_link() during
phylink_mac_link_{up,down} which provides semantically equivalent steps.
Drivers willing to take advantage of PHYLINK should implement the phylink_mac_*
operations that DSA wraps.
We cannot quite remove the adjust_link() callback just yet, because a number of
drivers rely on that for configuring their "CPU" and "DSA" ports, this is done
dsa_port_setup_phy_of() and dsa_port_fixed_link_register_of() still.
Drivers that utilize fixed links for user-facing ports (e.g: bcm_sf2) will need
to implement phylink_mac_ops from now on to preserve functionality, since PHYLINK
*does not* create a phy_device instance for fixed links.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding support for PHYLINK within DSA, define a number of
operations that we will need and that switch drivers can start implementing.
Proper integration with PHYLINK will follow in subsequent patches.
We start selecting PHYLINK (which implies PHYLIB) in net/dsa/Kconfig
such that drivers can be guaranteed that this dependency is properly
taken care of and can start referencing PHYLINK helper functions without
requiring stubs or anything.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the same type of ethtool diversion that we have for
ETH_SS_STATS and make it work with ETH_SS_PHY_STATS. This allows
providing PHY level statistics for CPU ports that are directly
connecting to a PHY device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we largely assumed that we were interested in ETH_SS_STATS
type of strings for all ethtool operations, this is about to change with
the introduction of additional string sets, e.g: ETH_SS_PHY_STATS.
Update all functions to take an appropriate stringset argument and act
on it when it is different than ETH_SS_STATS for now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By passing the port, we allow different ports to have different
statistics. This is useful since some ports have SERDES interfaces
with their own statistic counters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forward the rx/tx timestamp machinery from the dsa infrastructure to the
switch driver.
On the rx side, defer delivery of skbs until we have an rx timestamp.
This mimicks the behavior of skb_defer_rx_timestamp.
On the tx side, identify PTP packets, clone them, and pass them to the
underlying switch driver before we transmit. This mimicks the behavior
of skb_tx_timestamp.
Adjusted txstamp API to keep the allocation and freeing of the clone
in the same central function by Richard Cochran
Signed-off-by: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to the dsa slave network device so that
switch drivers can implement the SIOC[GS]HWTSTAMP ioctls and the
ethtool timestamp-info interface.
Signed-off-by: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a configuration option: CONFIG_NET_DSA_LEGACY allowing to compile out
support for the old platform device and Device Tree binding registration.
Support for these configurations is scheduled to be removed in 4.17.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current dsa_upstream_port() helper still assumes a unique CPU port
in the whole switch fabric. This is becoming wrong, as every port in the
fabric has its dedicated CPU port, thus every port has an upstream port.
Add a port argument to the dsa_upstream_port() helper and fetch its CPU
port instead of the deprecated unique fabric CPU port. A CPU or unused
port has no dedicated CPU port, so return itself in this case.
At the same time, change the return value from u8 to unsigned int since
there is no need to limit the size here.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new helper returning the local port used to reach an arbitrary
switch port in the fabric.
Its only user at the moment is the dsa_upstream_port helper, which
returns the local port reaching the dedicated CPU port, but it will be
used in cross-chip FDB operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch MDB ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from MDB prepare and add operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch VLAN ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from VLAN prepare and add operations.
At the same time, fix the following checkpatch warning:
WARNING: line over 80 characters
#74: FILE: drivers/net/dsa/dsa_loop.c:177:
+ const struct switchdev_obj_port_vlan *vlan)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new type: DSA_TAG_PROTO_PREPEND which allows us to support for the
4-bytes Broadcom tag that we already support, but in a format where it
is pre-pended to the packet instead of located between the MAC SA and
the Ethertyper (DSA_TAG_PROTO_BRCM).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers want to check whether the configured CPU port is a
possible configuration for enabling tagging, pass down the CPU port
number so they verify that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit provides better scope for the DSA tree setup and teardown
functions. It renames the "applied" bool to "setup" and print a message
when the tree is setup, as it is done during teardown.
At the same time, check dst->setup in dsa_tree_setup, where it is set to
true.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A DSA port has a dedicated CPU port assigned to it, stored in the cpu_dp
member. It is not meant to be modified by a port, thus make it const.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to a DSA switch and port, rename the tree index from "tree" to
"index" and make it an unsigned int because it isn't supposed to be less
than 0.
u32 is an OF specific data used to retrieve the value and has no need to
be propagated up to the tree index.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the DSA switch index as an unsigned int, because it will never be
less than 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA core provides port types, there is no need to keep this
information at the switch level. This is a static information that is
part of a DSA core dsa_port structure. Remove them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA exposes an enumerated type for the ports, we can use them
directly instead of checking bitmaps, which is more consistent.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an enumerated type for ports, which will be way more explicit
to identify a port type instead of digging into switch port masks.
A port can be of type CPU, DSA, user, or unused by default. This is a
static parsed information that cannot be changed at runtime.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a dsa_user_ports() helper to return the ds->enabled_port_mask
mask which is more explicit. This will also minimize diffs when touching
this internal mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames dsa_is_normal_port to dsa_is_user_port because "user"
is the correct term in the DSA terminology, not "normal".
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to know if a port is of type user, dsa_is_normal_port checks
that the given port is not of type DSA nor CPU. This is not enough
because a port can be unused.
Without the previous fix, this caused the unused mv88e6xxx ports to be
configured in normal mode.
The ds->enabled_port_mask reports the user ports, so check this instead.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the comment above the chunk states, the b53 driver attempts to
disable the unused ports. But using ds->enabled_port_mask is misleading,
because this mask reports in fact the user ports.
To avoid confusion and fix this, this patch introduces an explicit
dsa_is_unused_port helper which ensures the corresponding bit is not
masked in any of the switch port masks.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure is part of DSA core data and must only be updated
by the later. It is OK and sometimes necessary for the DSA drivers to
access this data, but this has to be read only.
For that purpose, add a dsa_to_port() helper which returns a const
pointer to a dsa_port structure which must be used by DSA drivers from
now on instead of digging into ds->ports[] themselves.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure has a "netdev" member, which can be used for
either the master device, or the slave device, depending on its type.
It is true that today, CPU port are not exposed to userspace, thus the
port's netdev member can be used to point to its master interface.
But it is still slightly confusing, so split it into more explicit
"master" and "slave" members inside an anonymous union.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is no user for the .set_addr function, remove it from
DSA. If a switch supports this feature (like mv88e6xxx), the
implementation can be done in the driver setup.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to tell the DSA master network device doing the actual
transmission what the desired switch port and queue number is for it to
resolve that to the internal transmit queue it is mapped to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
