Directs route lookups to VRF table. Compiles out if NET_VRF is not
enabled. With this patch able to successfully bring up ipsec tunnels
in VRFs, even with duplicate network configuration.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
slow start after idle might reduce cwnd, but we perform this
after first packet was cooked and sent.
With TSO/GSO, it means that we might send a full TSO packet
even if cwnd should have been reduced to IW10.
Moving the SSAI check in skb_entail() makes sense, because
we slightly reduce number of times this check is done,
especially for large send() and TCP Small queue callbacks from
softirq context.
As Neal pointed out, we also need to perform the check
if/when receive window opens.
Tested:
Following packetdrill test demonstrates the problem
// Test of slow start after idle
`sysctl -q net.ipv4.tcp_slow_start_after_idle=1`
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 65535 <mss 1000,sackOK,nop,nop,nop,wscale 7>
+0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 6>
+.100 < . 1:1(0) ack 1 win 511
+0 accept(3, ..., ...) = 4
+0 setsockopt(4, SOL_SOCKET, SO_SNDBUF, [200000], 4) = 0
+0 write(4, ..., 26000) = 26000
+0 > . 1:5001(5000) ack 1
+0 > . 5001:10001(5000) ack 1
+0 %{ assert tcpi_snd_cwnd == 10 }%
+.100 < . 1:1(0) ack 10001 win 511
+0 %{ assert tcpi_snd_cwnd == 20, tcpi_snd_cwnd }%
+0 > . 10001:20001(10000) ack 1
+0 > P. 20001:26001(6000) ack 1
+.100 < . 1:1(0) ack 26001 win 511
+0 %{ assert tcpi_snd_cwnd == 36, tcpi_snd_cwnd }%
+4 write(4, ..., 20000) = 20000
// If slow start after idle works properly, we should send 5 MSS here (cwnd/2)
+0 > . 26001:31001(5000) ack 1
+0 %{ assert tcpi_snd_cwnd == 10, tcpi_snd_cwnd }%
+0 > . 31001:36001(5000) ack 1
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cfg and family arguments to lwt build state functions. cfg is a void
pointer and will either be a pointer to a fib_config or fib6_config
structure. The family parameter indicates which one (either AF_INET
or AF_INET6).
LWT encpasulation implementation may use the fib configuration to build
the LWT state.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do WARN_ON_ONCE instead of WARN_ON in gue_gro_receive when the offload
callcaks are bad (either don't exist or gro_receive is not specified).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remote checksum offload GRO did not consider the case that frag0
might be in use. This patch fixes that by accessing headers using the
skb_gro functions and not saving offsets relative to skb->head.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
This is second pull request includes the conflict resolution patch that
resulted from the updates that we got for the conntrack template through
kmalloc. No changes with regards to the previously sent 15 patches.
The following patchset contains Netfilter updates for your net-next tree, they
are:
1) Rework the existing nf_tables counter expression to make it per-cpu.
2) Prepare and factor out common packet duplication code from the TEE target so
it can be reused from the new dup expression.
3) Add the new dup expression for the nf_tables IPv4 and IPv6 families.
4) Convert the nf_tables limit expression to use a token-based approach with
64-bits precision.
5) Enhance the nf_tables limit expression to support limiting at packet byte.
This comes after several preparation patches.
6) Add a burst parameter to indicate the amount of packets or bytes that can
exceed the limiting.
7) Add netns support to nfacct, from Andreas Schultz.
8) Pass the nf_conn_zone structure instead of the zone ID in nf_tables to allow
accessing more zone specific information, from Daniel Borkmann.
9) Allow to define zone per-direction to support netns containers with
overlapping network addressing, also from Daniel.
10) Extend the CT target to allow setting the zone based on the skb->mark as a
way to support simple mappings from iptables, also from Daniel.
11) Make the nf_tables payload expression aware of the fact that VLAN offload
may have removed a vlan header, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow specification of per route IP tunnel instructions also for IPv6.
This complements commit 3093fbe7ff ("route: Per route IP tunnel metadata
via lightweight tunnel").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
CC: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the lwtunnel state resides in per-protocol data. This is
a problem if we encapsulate ipv6 traffic in an ipv4 tunnel (or vice versa).
The xmit function of the tunnel does not know whether the packet has been
routed to it by ipv4 or ipv6, yet it needs the lwtstate data. Moving the
lwtstate data to dst_entry makes such inter-protocol tunneling possible.
As a bonus, this brings a nice diffstat.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the ipv4_tos and ipv4_ttl fields to just 'tos' and 'ttl', as they'll
be used with IPv6 tunnels, too.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the IPv6 addresses as an union with IPv4 ones. When using IPv4, the
newly introduced padding after the IPv4 addresses needs to be zeroed out.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas reported breakage adding routes with local nexthops:
$ ip route show table main
...
172.28.0.0/24 dev vnf-xe1p0 proto kernel scope link src 172.28.0.16
$ ip route add 10.0.0.0/8 via 172.28.0.32 table 100 dev vnf-xe1p0
RTNETLINK answers: Resource temporarily unavailable
3bfd847203 changed the lookup to use the passed in table but for cases like
this the nexthop is in the local table rather than the passed in table.
Fixes: 3bfd847203 ("net: Use passed in table for nexthop lookups")
Reported-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make fib_encap_match() static as it isn't used outside the file.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, two routes going through the same tunnel interface are considered
the same even when they are routed to a different host after encapsulation.
This causes all routes added after the first one to have incorrect
encapsulation parameters.
This is nicely visible by doing:
# ip r a 192.168.1.2/32 dev vxlan0 tunnel dst 10.0.0.2
# ip r a 192.168.1.3/32 dev vxlan0 tunnel dst 10.0.0.3
# ip r
[...]
192.168.1.2/32 tunnel id 0 src 0.0.0.0 dst 10.0.0.2 [...]
192.168.1.3/32 tunnel id 0 src 0.0.0.0 dst 10.0.0.2 [...]
Implement the missing comparison function.
Fixes: 3093fbe7ff ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The built lwtunnel_state struct has to be freed after comparison.
Fixes: 571e722676 ("ipv4: support for fib route lwtunnel encap attributes")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_proto_csum_replace4,2,16 take a pseudohdr argument which indicates
the checksum field carries a pseudo header. This argument should be a
boolean instead of an int.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the capability to redirect dst input in the same way
that dst output is redirected by LWT.
Also, save the original dst.input and and dst.out when setting up
lwtunnel redirection. These can be called by the client as a pass-
through.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds the possibility of deriving the zone id from the skb->mark
field in a scalable manner. This allows for having only a single template
serving hundreds/thousands of different zones, for example, instead of the
need to have one match for each zone as an extra CT jump target.
Note that we'd need to have this information attached to the template as at
the time when we're trying to lookup a possible ct object, we already need
to know zone information for a possible match when going into
__nf_conntrack_find_get(). This work provides a minimal implementation for
a possible mapping.
In order to not add/expose an extra ct->status bit, the zone structure has
been extended to carry a flag for deriving the mark.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This work adds a direction parameter to netfilter zones, so identity
separation can be performed only in original/reply or both directions
(default). This basically opens up the possibility of doing NAT with
conflicting IP address/port tuples from multiple, isolated tenants
on a host (e.g. from a netns) without requiring each tenant to NAT
twice resp. to use its own dedicated IP address to SNAT to, meaning
overlapping tuples can be made unique with the zone identifier in
original direction, where the NAT engine will then allocate a unique
tuple in the commonly shared default zone for the reply direction.
In some restricted, local DNAT cases, also port redirection could be
used for making the reply traffic unique w/o requiring SNAT.
The consensus we've reached and discussed at NFWS and since the initial
implementation [1] was to directly integrate the direction meta data
into the existing zones infrastructure, as opposed to the ct->mark
approach we proposed initially.
As we pass the nf_conntrack_zone object directly around, we don't have
to touch all call-sites, but only those, that contain equality checks
of zones. Thus, based on the current direction (original or reply),
we either return the actual id, or the default NF_CT_DEFAULT_ZONE_ID.
CT expectations are direction-agnostic entities when expectations are
being compared among themselves, so we can only use the identifier
in this case.
Note that zone identifiers can not be included into the hash mix
anymore as they don't contain a "stable" value that would be equal
for both directions at all times, f.e. if only zone->id would
unconditionally be xor'ed into the table slot hash, then replies won't
find the corresponding conntracking entry anymore.
If no particular direction is specified when configuring zones, the
behaviour is exactly as we expect currently (both directions).
Support has been added for the CT netlink interface as well as the
x_tables raw CT target, which both already offer existing interfaces
to user space for the configuration of zones.
Below a minimal, simplified collision example (script in [2]) with
netperf sessions:
+--- tenant-1 ---+ mark := 1
| netperf |--+
+----------------+ | CT zone := mark [ORIGINAL]
[ip,sport] := X +--------------+ +--- gateway ---+
| mark routing |--| SNAT |-- ... +
+--------------+ +---------------+ |
+--- tenant-2 ---+ | ~~~|~~~
| netperf |--+ +-----------+ |
+----------------+ mark := 2 | netserver |------ ... +
[ip,sport] := X +-----------+
[ip,port] := Y
On the gateway netns, example:
iptables -t raw -A PREROUTING -j CT --zone mark --zone-dir ORIGINAL
iptables -t nat -A POSTROUTING -o <dev> -j SNAT --to-source <ip> --random-fully
iptables -t mangle -A PREROUTING -m conntrack --ctdir ORIGINAL -j CONNMARK --save-mark
iptables -t mangle -A POSTROUTING -m conntrack --ctdir REPLY -j CONNMARK --restore-mark
conntrack dump from gateway netns:
netperf -H 10.1.1.2 -t TCP_STREAM -l60 -p12865,5555 from each tenant netns
tcp 6 431995 ESTABLISHED src=40.1.1.1 dst=10.1.1.2 sport=5555 dport=12865 zone-orig=1
src=10.1.1.2 dst=10.1.1.1 sport=12865 dport=1024
[ASSURED] mark=1 secctx=system_u:object_r:unlabeled_t:s0 use=1
tcp 6 431994 ESTABLISHED src=40.1.1.1 dst=10.1.1.2 sport=5555 dport=12865 zone-orig=2
src=10.1.1.2 dst=10.1.1.1 sport=12865 dport=5555
[ASSURED] mark=2 secctx=system_u:object_r:unlabeled_t:s0 use=1
tcp 6 299 ESTABLISHED src=40.1.1.1 dst=10.1.1.2 sport=39438 dport=33768 zone-orig=1
src=10.1.1.2 dst=10.1.1.1 sport=33768 dport=39438
[ASSURED] mark=1 secctx=system_u:object_r:unlabeled_t:s0 use=1
tcp 6 300 ESTABLISHED src=40.1.1.1 dst=10.1.1.2 sport=32889 dport=40206 zone-orig=2
src=10.1.1.2 dst=10.1.1.1 sport=40206 dport=32889
[ASSURED] mark=2 secctx=system_u:object_r:unlabeled_t:s0 use=2
Taking this further, test script in [2] creates 200 tenants and runs
original-tuple colliding netperf sessions each. A conntrack -L dump in
the gateway netns also confirms 200 overlapping entries, all in ESTABLISHED
state as expected.
I also did run various other tests with some permutations of the script,
to mention some: SNAT in random/random-fully/persistent mode, no zones (no
overlaps), static zones (original, reply, both directions), etc.
[1] http://thread.gmane.org/gmane.comp.security.firewalls.netfilter.devel/57412/
[2] https://paste.fedoraproject.org/242835/65657871/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Table lookup compiles out when VRF is not enabled.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have IFLA_IPTUN_ netlink attributes. The IP_TUN_ attributes look
very similar, yet they serve very different purpose. This is confusing for
anyone trying to implement a user space tool supporting lwt.
As the IP_TUN_ attributes are used only for the lightweight tunnels, prefix
them with LWTUNNEL_IP_ instead to make their purpose clear. Also, it's more
logical to have them in lwtunnel.h together with the encap enum.
Fixes: 3093fbe7ff ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2015-08-17
1) Fix IPv6 ECN decapsulation for IPsec interfamily tunnels.
From Thomas Egerer.
2) Use kmemdup instead of duplicating it in xfrm_dump_sa().
From Andrzej Hajda.
3) Pass oif to the xfrm lookups so that it gets set on the flow
and the resolver routines can match based on oif.
From David Ahern.
4) Add documentation for the new xfrm garbage collector threshold.
From Alexander Duyck.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8133534c76 ("net: limit tcp/udp rmem/wmem to
SOCK_{RCV,SND}BUF_MIN") modified four sysctls to enforce that the values
written to them are not less than SOCK_MIN_{RCV,SND}BUF.
That change causes 4096 to no longer be accepted as a valid value for
'min' in tcp_wmem and udp_wmem_min. 4096 has been the default for both
of those sysctls for a long time, and unfortunately seems to be an
extremely popular setting. This change breaks a large number of sysctl
configurations at Facebook.
That commit referred to b1cb59cf2e ("net: sysctl_net_core: check
SNDBUF and RCVBUF for min length"), which choose to use the SOCK_MIN
constants as the lower limits to avoid nasty bugs. But AFAICS, a limit
of SOCK_MIN_SNDBUF isn't necessary to do that: the BUG_ON cited in the
commit message seems to have happened because unix_stream_sendmsg()
expects a minimum of a full page (ie SK_MEM_QUANTUM) and the math broke,
not because it had less than SOCK_MIN_SNDBUF allocated.
This particular issue doesn't seem to affect TCP however: using a
setting of "1 1 1" for tcp_{r,w}mem works, although it's obviously
suboptimal. SK_MEM_QUANTUM would be a nice minimum, but it's 64K on
some archs, so there would still be breakage.
Since a value of one doesn't seem to cause any problems, we can drop the
minimum 8133534c added to fix this.
This reverts commit 8133534c76.
Fixes: 8133534c76 ("net: limit tcp/udp rmem/wmem to SOCK_MIN...")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sorin Dumitru <sorin@returnze.ro>
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_lookup() forces FIB_LOOKUP_NOREF flag, while fib_table_lookup()
does not.
This patch solves the typical message at reboot time or device
dismantle :
unregister_netdevice: waiting for eth0 to become free. Usage count = 4
Fixes: 3bfd847203 ("net: Use passed in table for nexthop lookups")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ahern <dsa@cumulusnetworks.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When replacing del_timer() with del_timer_sync(), I introduced
a deadlock condition :
reqsk_queue_unlink() is called from inet_csk_reqsk_queue_drop()
inet_csk_reqsk_queue_drop() can be called from many contexts,
one being the timer handler itself (reqsk_timer_handler()).
In this case, del_timer_sync() loops forever.
Simple fix is to test if timer is pending.
Fixes: 2235f2ac75 ("inet: fix races with reqsk timers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fragmentation cache uses information from the IP header to reassemble
packets. That information can be duplicated across VRFs -- same source
and destination addresses, protocol and id. Handle fragmentation with
VRFs by adding the VRF device index to entries in the cache and the
lookup arg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If output device is not specified use VRF device if input device is
enslaved. This is needed to ensure tcp acks and resets go out VRF device.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a user passes in a table for new routes use that table for nexthop
lookups. Specifically, this solves the case where a connected route does
not exist in the main table, but only another table and then a subsequent
route is added with a next hop using the connected route. ie.,
$ ip route ls
default via 10.0.2.2 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
169.254.0.0/16 dev eth0 scope link metric 1003
192.168.56.0/24 dev eth1 proto kernel scope link src 192.168.56.51
$ ip route ls table 10
1.1.1.0/24 dev eth2 scope link
Without this patch adding a nexthop route fails:
$ ip route add table 10 2.2.2.0/24 via 1.1.1.10
RTNETLINK answers: Network is unreachable
With this patch the route is added successfully.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a device associated with a VRF is brought up or down routes
should be added to/removed from the table associated with the VRF.
fib_magic defaults to using the main or local tables. Have it use
the table with the device if there is one.
A part of this is directing prefsrc validations to the correct
table as well.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently inet_addr_type and inet_dev_addr_type expect local addresses
to be in the local table. With the VRF device local routes for devices
associated with a VRF will be in the table associated with the VRF.
Provide an alternate inet_addr lookup to use a specific table rather
than defaulting to the local table.
inet_addr_type_dev_table keeps the same semantics as inet_addr_type but
if the passed in device is enslaved to a VRF then the table for that VRF
is used for the lookup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently inet_addr_type and inet_dev_addr_type expect local addresses
to be in the local table. With the VRF device local routes for devices
associated with a VRF will be in the table associated with the VRF.
Provide an alternate inet_addr lookup to use a specific table rather
than defaulting to the local table.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For unconnected UDP sockets using a VRF device lookup source address
based on VRF table. This allows the UDP header to be properly setup
before showing up at the VRF device via the dst.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with ingress use the index of VRF master device for route lookups on
egress. However, the oif should only be used to direct the lookups to a
specific table. Routes in the table are not based on the VRF device but
rather interfaces that are part of the VRF so do not consider the oif for
lookups within the table. The FLOWI_FLAG_VRFSRC is used to control this
latter part.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ingress use index of VRF master device for route lookups if real device
is enslaved. Rules are expected to be installed for the VRF device to
direct lookups to a specific table.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When generating /proc/net/route we emit a header followed by a line for
each route. When a short read is performed we will restart this process
based on the open file descriptor. When calculating the start point we
fail to take into account that the 0th entry is the header. This leads
us to skip the first entry when doing a continuation read.
This can be easily seen with the comparison below:
while read l; do echo "$l"; done </proc/net/route >A
cat /proc/net/route >B
diff -bu A B | grep '^[+-]'
On my example machine I have approximatly 10KB of route output. There we
see the very first non-title element is lost in the while read case,
and an entry around the 8K mark in the cat case:
+wlan0 00000000 02021EAC 0003 0 0 400 00000000 0 0 0
-tun1 00C0AC0A 00000000 0001 0 0 950 00C0FFFF 0 0 0
Fix up the off-by-one when reaquiring position on continuation.
Fixes: 8be33e955c ("fib_trie: Fib walk rcu should take a tnode and key instead of a trie and a leaf")
BugLink: http://bugs.launchpad.net/bugs/1483440
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent refactoring of the IGMP and MLD parsing code into
ipv6_mc_check_mld() / ip_mc_check_igmp() introduced a potential crash /
BUG() invocation for bridges:
I wrongly assumed that skb_get() could be used as a simple reference
counter for an skb which is not the case. skb_get() bears additional
semantics, a user count. This leads to a BUG() invocation in
pskb_expand_head() / kernel panic if pskb_may_pull() is called on an skb
with a user count greater than one - unfortunately the refactoring did
just that.
Fixing this by removing the skb_get() call and changing the API: The
caller of ipv6_mc_check_mld() / ip_mc_check_igmp() now needs to
additionally check whether the returned skb_trimmed is a clone.
Fixes: 9afd85c9e4 ("net: Export IGMP/MLD message validation code")
Reported-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TLP fails to send new packet because of receive window
limit, it should fall back to retransmit the last packet instead.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If TLP was unable to send a probe, it extended the RTO to
now + icsk_rto. But extending the RTO makes little sense
if no TLP probe went out. With this commit, instead of
extending the RTO we re-arm it relative to the transmit time
of the write queue head.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a system has multiple ethernet devices and during DHCP
request (for using NFS), the system waits only for HZ/2 which is
500mS before switching to another interface for DHCP.
There are some routers (Ex: Trendnet routers) which responds to
DHCP request at about 560mS. When the system has only one
ethernet interface there is no issue as the timeout is 2S and the
dev xid doesn't changes and only retries.
But when the system has multiple Ethernet like DRA74x with CPSW
in dual EMAC mode, the DHCP response is dropped as the dev xid
changes while shifting to the next device. So changing inter
device timeout to HZ (which is 1S).
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rules can be installed that direct route lookups to specific tables based
on oif. Plumb the oif through the xfrm lookups so it gets set in the flow
struct and passed to the resolver routines.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch replaces the zone id which is pushed down into functions
with the actual zone object. It's a bigger one-time change, but
needed for later on extending zones with a direction parameter, and
thus decoupling this additional information from all call-sites.
No functional changes in this patch.
The default zone becomes a global const object, namely nf_ct_zone_dflt
and will be returned directly in various cases, one being, when there's
f.e. no zoning support.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In commit b357a364c5 ("inet: fix possible panic in
reqsk_queue_unlink()"), I missed fact that tcp_check_req()
can return the listener socket in one case, and that we must
release the request socket refcount or we leak it.
Tested:
Following packetdrill test template shows the issue
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 2920 <mss 1460,sackOK,nop,nop>
+0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK>
+.002 < . 1:1(0) ack 21 win 2920
+0 > R 21:21(0)
Fixes: b357a364c5 ("inet: fix possible panic in reqsk_queue_unlink()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reqsk_queue_destroy() and reqsk_queue_unlink() should use
del_timer_sync() instead of del_timer() before calling reqsk_put(),
otherwise we could free a req still used by another cpu.
But before doing so, reqsk_queue_destroy() must release syn_wait_lock
spinlock or risk a dead lock, as reqsk_timer_handler() might
need to take this same spinlock from reqsk_queue_unlink() (called from
inet_csk_reqsk_queue_drop())
Fixes: fa76ce7328 ("inet: get rid of central tcp/dccp listener timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains five Netfilter fixes for your net tree,
they are:
1) Silence a warning on falling back to vmalloc(). Since 88eab472ec, we can
easily hit this warning message, that gets users confused. So let's get rid
of it.
2) Recently when porting the template object allocation on top of kmalloc to
fix the netns dependencies between x_tables and conntrack, the error
checks where left unchanged. Remove IS_ERR() and check for NULL instead.
Patch from Dan Carpenter.
3) Don't ignore gfp_flags in the new nf_ct_tmpl_alloc() function, from
Joe Stringer.
4) Fix a crash due to NULL pointer dereference in ip6t_SYNPROXY, patch from
Phil Sutter.
5) The sequence number of the Syn+ack that is sent from SYNPROXY to clients is
not adjusted through our NAT infrastructure, as a result the client may
ignore this TCP packet and TCP flow hangs until the client probes us. Also
from Phil Sutter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for sharing GREPROTO_CISCO port was added so that
OVS gre port and kernel GRE devices can co-exist. After
flow-based tunneling patches OVS GRE protocol processing
is completely moved to ip_gre module. so there is no need
for GRE protocol hook. Following patch consolidates
GRE protocol related functions into ip_gre module.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using GRE tunnel meta data collection feature, we can implement
OVS GRE vport. This patch removes all of the OVS
specific GRE code and make OVS use a ip_gre net_device.
Minimal GRE vport is kept to handle compatibility with
current userspace application.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch create new tunnel flag which enable
tunnel metadata collection on given device.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receipt of SYNACK from the server, ipt_SYNPROXY first sends back an ACK to
finish the server handshake, then calls nf_ct_seqadj_init() to initiate
sequence number adjustment of forwarded packets to the client and finally sends
a window update to the client to unblock it's TX queue.
Since synproxy_send_client_ack() does not set synproxy_send_tcp()'s nfct
parameter, no sequence number adjustment happens and the client receives the
window update with incorrect sequence number. Depending on client TCP
implementation, this leads to a significant delay (until a window probe is
being sent).
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This new expression uses the nf_dup engine to clone packets to a given gateway.
Unlike xt_TEE, we use an index to indicate output interface which should be
fine at this stage.
Moreover, change to the preemtion-safe this_cpu_read(nf_skb_duplicated) from
nf_dup_ipv{4,6} to silence a lockdep splat.
Based on the original tee expression from Arturo Borrero Gonzalez, although
this patch has diverted quite a bit from this initial effort due to the
change to support maps.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Extracted from the xtables TEE target. This creates two new modules for IPv4
and IPv6 that are shared between the TEE target and the new nf_tables dup
expressions.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next, they are:
1) A couple of cleanups for the netfilter core hook from Eric Biederman.
2) Net namespace hook registration, also from Eric. This adds a dependency with
the rtnl_lock. This should be fine by now but we have to keep an eye on this
because if we ever get the per-subsys nfnl_lock before rtnl we have may
problems in the future. But we have room to remove this in the future by
propagating the complexity to the clients, by registering hooks for the init
netns functions.
3) Update nf_tables to use the new net namespace hook infrastructure, also from
Eric.
4) Three patches to refine and to address problems from the new net namespace
hook infrastructure.
5) Switch to alternate jumpstack in xtables iff the packet is reentering. This
only applies to a very special case, the TEE target, but Eric Dumazet
reports that this is slowing down things for everyone else. So let's only
switch to the alternate jumpstack if the tee target is in used through a
static key. This batch also comes with offline precalculation of the
jumpstack based on the callchain depth. From Florian Westphal.
6) Minimal SCTP multihoming support for our conntrack helper, from Michal
Kubecek.
7) Reduce nf_bridge_info per skbuff scratchpad area to 32 bytes, from Florian
Westphal.
8) Fix several checkpatch errors in bridge netfilter, from Bernhard Thaler.
9) Get rid of useless debug message in ip6t_REJECT, from Subash Abhinov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
lwtunnel encap is applied for forwarded packets, but not for
locally-generated packets. This is because the output function is not
overridden in __mkroute_output, unlike it is in __mkroute_input.
The lwtunnel state is correctly set on the rth through the call to
rt_set_nexthop, so all that needs to be done is to override the dst
output function to be lwtunnel_output if there is lwtunnel state
present and it requires output redirection.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast dst are not cached. They carry DST_NOCACHE.
As mentioned in commit f886497212 ("ipv4: fix dst race in
sk_dst_get()"), these dst need special care before caching them
into a socket.
Caching them is allowed only if their refcnt was not 0, ie we
must use atomic_inc_not_zero()
Also, we must use READ_ONCE() to fetch sk->sk_rx_dst, as mentioned
in commit d0c294c53a ("tcp: prevent fetching dst twice in early demux
code")
Fixes: 421b3885bf ("udp: ipv4: Add udp early demux")
Tested-by: Gregory Hoggarth <Gregory.Hoggarth@alliedtelesis.co.nz>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Gregory Hoggarth <Gregory.Hoggarth@alliedtelesis.co.nz>
Reported-by: Alex Gartrell <agartrell@fb.com>
Cc: Michal Kubeček <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use union for most of the temporary cruft (original ipv4/ipv6
address, source mac, physoutdev) since they're used during different
stages of br netfilter traversal.
Also get rid of the last two ->mask users.
Shrinks struct from 48 to 32 on 64bit arch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch creates sk_set_txhash and eliminates protocol specific
inet_set_txhash and ip6_set_txhash. sk_set_txhash simply sets a
random number instead of performing flow dissection. sk_set_txash
is also allowed to be called multiple times for the same socket,
we'll need this when redoing the hash for negative routing advice.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When arp is off on a device, and ioctl(SIOCGARP) is queried,
a buggy answer is given with MAC address of the device, instead
of the mac address of the destination/gateway.
We filter out NUD_NOARP neighbours for /proc/net/arp,
we must do the same for SIOCGARP ioctl.
Tested:
lpaa23:~# ./arp 10.246.7.190
MAC=00:01:e8:22:cb:1d // correct answer
lpaa23:~# ip link set dev eth0 arp off
lpaa23:~# cat /proc/net/arp # check arp table is now 'empty'
IP address HW type Flags HW address Mask Device
lpaa23:~# ./arp 10.246.7.190
MAC=00:1a:11:c3:0d:7f // buggy answer before patch (this is eth0 mac)
After patch :
lpaa23:~# ip link set dev eth0 arp off
lpaa23:~# ./arp 10.246.7.190
ioctl(SIOCGARP) failed: No such device or address
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Vytautas Valancius <valas@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This notification causes the FIB to be updated, which is not needed
because the address already exists, and more importantly it may undo
intentional changes that were made to the FIB after the address was
originally added. (As a point of comparison, when an address becomes
deprecated because its preferred lifetime expired, a notification on
this chain is not generated.)
The motivation for this commit is fixing an incompatibility between
DHCP clients which set and update the address lifetime according to
the lease, and a commercial VPN client which replaces kernel routes
in a way that outbound traffic is sent only through the tunnel (and
disconnects if any further route changes are detected via netlink).
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that update_suffix was taking a long time on systems where
a large number of leaves were attached to a single node. As it turns out
fib_table_flush was calling update_suffix for each leaf that didn't have all
of the aliases stripped from it. As a result, on this large node removing
one leaf would result in us calling update_suffix for every other leaf on
the node.
The fix is to just remove the calls to leaf_pull_suffix since they are
redundant as we already have a call in resize that will go through and
update the suffix length for the node before we exit out of
fib_table_flush or fib_table_flush_external.
Reported-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing experiments with reordering resilience, we found
linux senders were not able to send at full speed under reordering,
because every incoming SACK was releasing one MSS.
This patch removes the limitation, as we did for CWR state
in commit a0ea700e40 ("tcp: tso: allow CA_CWR state in
tcp_tso_should_defer()")
Neal Cardwell had a concern about limited transmit so
Yuchung conducted experiments on GFE and found nothing
worth adding an extra check on fast path :
if (icsk->icsk_ca_state == TCP_CA_Disorder &&
tcp_sk(sk)->reordering == sysctl_tcp_reordering)
goto send_now;
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, tcp_recvmsg enters a busy loop in sk_wait_data if called
with flags = MSG_WAITALL | MSG_PEEK.
sk_wait_data waits for sk_receive_queue not empty, but in this case,
the receive queue is not empty, but does not contain any skb that we
can use.
Add a "last skb seen on receive queue" argument to sk_wait_data, so
that it sleeps until the receive queue has new skbs.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99461
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=18493
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1205258
Reported-by: Enrico Scholz <rh-bugzilla@ensc.de>
Reported-by: Dan Searle <dan@censornet.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It saves some lines and simplify a bit the code when the state is returning
by this function. It's also useful to handle a NULL entry.
To avoid too long lines, I've also renamed lwtunnel_state_get() and
lwtunnel_state_put() to lwtstate_get() and lwtstate_put().
CC: Thomas Graf <tgraf@suug.ch>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can simply remove the INET_FRAG_EVICTED flag to avoid all the flags
race conditions with the evictor and use a participation test for the
evictor list, when we're at that point (after inet_frag_kill) in the
timer there're 2 possible cases:
1. The evictor added the entry to its evictor list while the timer was
waiting for the chainlock
or
2. The timer unchained the entry and the evictor won't see it
In both cases we should be able to see list_evictor correctly due
to the sync on the chainlock.
Joint work with Florian Westphal.
Tested-by: Frank Schreuder <fschreuder@transip.nl>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank reports 'NMI watchdog: BUG: soft lockup' errors when
load is high. Instead of (potentially) unbounded restarts of the
eviction process, just skip to the next entry.
One caveat is that, when a netns is exiting, a timer may still be running
by the time inet_evict_bucket returns.
We use the frag memory accounting to wait for outstanding timers,
so that when we free the percpu counter we can be sure no running
timer will trip over it.
Reported-and-tested-by: Frank Schreuder <fschreuder@transip.nl>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup patch will call it after inet_frag_queue was freed, so q->net
doesn't work anymore (but netf = q->net; free(q); mem_limit(netf) would).
Tested-by: Frank Schreuder <fschreuder@transip.nl>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 65ba1f1ec0 ("inet: frags: fix a race between inet_evict_bucket
and inet_frag_kill") describes the bug, but the fix doesn't work reliably.
Problem is that ->flags member can be set on other cpu without chainlock
being held by that task, i.e. the RMW-Cycle can clear INET_FRAG_EVICTED
bit after we put the element on the evictor private list.
We can crash when walking the 'private' evictor list since an element can
be deleted from list underneath the evictor.
Join work with Nikolay Alexandrov.
Fixes: b13d3cbfb8 ("inet: frag: move eviction of queues to work queue")
Reported-by: Johan Schuijt <johan@transip.nl>
Tested-by: Frank Schreuder <fschreuder@transip.nl>
Signed-off-by: Nikolay Alexandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we do not notice if new alternative gateways
are added. We can do it by checking for present neigh
entry. Also, gateways that are currently probed (NUD_INCOMPLETE)
can be skipped from round-robin probing.
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_select_default considers alternative routes only when
res->fi is for the first alias in res->fa_head. In the
common case this can happen only when the initial lookup
matches the first alias with highest TOS value. This
prevents the alternative routes to require specific TOS.
This patch solves the problem as follows:
- routes that require specific TOS should be returned by
fib_select_default only when TOS matches, as already done
in fib_table_lookup. This rule implies that depending on the
TOS we can have many different lists of alternative gateways
and we have to keep the last used gateway (fa_default) in first
alias for the TOS instead of using single tb_default value.
- as the aliases are ordered by many keys (TOS desc,
fib_priority asc), we restrict the possible results to
routes with matching TOS and lowest metric (fib_priority)
and routes that match any TOS, again with lowest metric.
For example, packet with TOS 8 can not use gw3 (not lowest
metric), gw4 (different TOS) and gw6 (not lowest metric),
all other gateways can be used:
tos 8 via gw1 metric 2 <--- res->fa_head and res->fi
tos 8 via gw2 metric 2
tos 8 via gw3 metric 3
tos 4 via gw4
tos 0 via gw5
tos 0 via gw6 metric 1
Reported-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_trie starting from 4.1 can link fib aliases from
different prefixes in same list. Make sure the alternative
gateways are in same table and for same prefix (0) by
checking tb_id and fa_slen.
Fixes: 79e5ad2ceb ("fib_trie: Remove leaf_info")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the module_init() to a invocation from inet_init() since
ip_tunnel_core is part of the INET built-in.
Fixes: 3093fbe7ff ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton reported following warning on one ARM build
with gcc-4.4 :
net/ipv4/inet_hashtables.c: In function 'inet_ehash_locks_alloc':
net/ipv4/inet_hashtables.c:617: warning: division by zero
Even guarded with a test on sizeof(spinlock_t), compiler does not
like current construct on a !CONFIG_SMP build.
Remove the warning by using a temporary variable.
Fixes: 095dc8e0c3 ("tcp: fix/cleanup inet_ehash_locks_alloc()")
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This add the ability to select a routing table based on the tunnel
id which allows to maintain separate routing tables for each virtual
tunnel network.
ip rule add from all tunnel-id 100 lookup 100
ip rule add from all tunnel-id 200 lookup 200
A new static key controls the collection of metadata at tunnel level
upon demand.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a new IP tunnel lightweight tunnel type which allows
to specify IP tunnel instructions per route. Only IPv4 is supported
at this point.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new flowi_tunnel structure which is a subset of ip_tunnel_key to
allow routes to match on tunnel metadata. For now, the tunnel id is
added to flowi_tunnel which allows for routes to be bound to specific
virtual tunnels.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If output device wants to see the dst, inherit the dst of the
original skb and pass it on to generate the ARP request.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduces a new dst_metadata which enables to carry per packet metadata
between forwarding and processing elements via the skb->dst pointer.
The structure is set up to be a union. Thus, each separate type of
metadata requires its own dst instance. If demand arises to carry
multiple types of metadata concurrently, metadata dst entries can be
made stackable.
The metadata dst entry is refcnt'ed as expected for now but a non
reference counted use is possible if the reference is forced before
queueing the skb.
In order to allow allocating dsts with variable length, the existing
dst_alloc() is split into a dst_alloc() and dst_init() function. The
existing dst_init() function to initialize the subsystem is being
renamed to dst_subsys_init() to make it clear what is what.
The check before ip_route_input() is changed to ignore metadata dsts
and drop the dst inside the routing function thus allowing to interpret
metadata in a later commit.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_input() unconditionally overwrites the dst. Hide the original
dst attached to the skb by calling skb_dst_set(skb, NULL) prior to
ip_route_input().
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For input routes with tunnel encap state this patch redirects
dst output functions to lwtunnel_output which later resolves to
the corresponding lwtunnel output function.
This has been tested to work with mpls ip tunnels.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support in ipv4 fib functions to parse user
provided encap attributes and attach encap state data to fib_nh
and rtable.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ip_frag_queue() computes positions, it assumes that the passed
sk_buff does not contain L2 headers.
However, when PACKET_FANOUT_FLAG_DEFRAG is used, IP reassembly
functions can be called on outgoing packets that contain L2 headers.
Also, IPv4 checksum is not corrected after reassembly.
Fixes: 7736d33f42 ("packet: Add pre-defragmentation support for ipv4 fanouts.")
Signed-off-by: Edward Hyunkoo Jee <edjee@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_datagram_connect() is doing a lot of socket changes without
socket being locked.
This looks wrong, at least for udp_lib_rehash() which could corrupt
lists because of concurrent udp_sk(sk)->udp_portaddr_hash accesses.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently F-RTO may repeatedly send new data packets on non-recurring
timeouts in CA_Loss mode. This is a bug because F-RTO (RFC5682)
should only be used on either new recovery or recurring timeouts.
This exacerbates the recovery progress during frequent timeout &
repair, because we prioritize sending new data packets instead of
repairing the holes when the bandwidth is already scarce.
Fix it by correcting the test of a new recovery episode.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't bother testing if we need to switch to alternate stack
unless TEE target is used.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In most cases there is no reentrancy into ip/ip6tables.
For skbs sent by REJECT or SYNPROXY targets, there is one level
of reentrancy, but its not relevant as those targets issue an absolute
verdict, i.e. the jumpstack can be clobbered since its not used
after the target issues absolute verdict (ACCEPT, DROP, STOLEN, etc).
So the only special case where it is relevant is the TEE target, which
returns XT_CONTINUE.
This patch changes ip(6)_do_table to always use the jump stack starting
from 0.
When we detect we're operating on an skb sent via TEE (percpu
nf_skb_duplicated is 1) we switch to an alternate stack to leave
the original one alone.
Since there is no TEE support for arptables, it doesn't need to
test if tee is active.
The jump stack overflow tests are no longer needed as well --
since ->stacksize is the largest call depth we cannot exceed it.
A much better alternative to the external jumpstack would be to just
declare a jumps[32] stack on the local stack frame, but that would mean
we'd have to reject iptables rulesets that used to work before.
Another alternative would be to start rejecting rulesets with a larger
call depth, e.g. 1000 -- in this case it would be feasible to allocate the
entire stack in the percpu area which would avoid one dereference.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The {arp,ip,ip6tables} jump stack is currently sized based
on the number of user chains.
However, its rather unlikely that every user defined chain jumps to the
next, so lets use the existing loop detection logic to also track the
chain depths.
The stacksize is then set to the largest chain depth seen.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
net/bridge/br_mdb.c
Minor conflict in br_mdb.c, in 'net' we added a memset of the
on-stack 'ip' variable whereas in 'net-next' we assign a new
member 'vid'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3cc4949269.
There is nothing wrong with coalescing during defragmentation, it
reduces truesize overhead and simplifies things for the receiving
socket (no fraglist walk needed).
However, it also destroys geometry of the original fragments.
While that doesn't cause any breakage (we make sure to not exceed largest
original size) ip_do_fragment contains a 'fastpath' that takes advantage
of a present frag list and results in fragments that (in most cases)
match what was received.
In case its needed the coalescing could be done later, when we're sure
the skb is not forwarded. But discussion during NFWS resulted in
'lets just remove this for now'.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reconsidering my commit 20462155 "net: inet_diag: export IPV6_V6ONLY
sockopt", I am not happy with the limitations it causes for socket
analysing code in userspace. Exporting the value only if it is set makes
it hard for userspace to decide whether the option is not set or the
kernel does not support exporting the option at all.
>From an auditor's perspective, the interesting question for listening
AF_INET6 sockets is: "Does it NOT have IPV6_V6ONLY set?" Because it is
the unexpected case. This patch allows to answer this question reliably.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 900f65d361 ("tcp: move duplicate code from
tcp_v4_init_sock()/tcp_v6_init_sock()"), we no longer
need to export tcp_init_xmit_timers()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flags local variable in __mkroute_input is not used as a variable.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to allow non-local binds similar to how this was done for IPv4.
Non-local binds are very useful in emulating the Internet in a box, etc.
This add the ip_nonlocal_bind sysctl under ipv6.
Testing:
Set up nonlocal binding and receive routing on a host, e.g.:
ip -6 rule add from ::/0 iif eth0 lookup 200
ip -6 route add local 2001:0:0:1::/64 dev lo proto kernel scope host table 200
sysctl -w net.ipv6.ip_nonlocal_bind=1
Set up routing to 2001:0:0:1::/64 on peer to go to first host
ping6 -I 2001:0:0:1::1 peer-address -- to verify
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_twsk_deschedule() calls are followed by inet_twsk_put().
Only particular case is in inet_twsk_purge() but there is no point
to defer the inet_twsk_put() after re-enabling BH.
Lets rename inet_twsk_deschedule() to inet_twsk_deschedule_put()
and move the inet_twsk_put() inside.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
timewait sockets have a complex refcounting logic.
Once we realize it should be similar to established and
syn_recv sockets, we can use sk_nulls_del_node_init_rcu()
and remove inet_twsk_unhash()
In particular, deferred inet_twsk_put() added in commit
13475a30b6 ("tcp: connect() race with timewait reuse")
looks unecessary : When removing a timewait socket from
ehash or bhash, caller must own a reference on the socket
anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The congestion state and cwnd can be updated in the wrong order.
For example, upon receiving a dubious ACK, we incorrectly raise
the cwnd first (tcp_may_raise_cwnd()/tcp_cong_avoid()) because
the state is still Open, then enter recovery state to reduce cwnd.
For another example, if the ACK indicates spurious timeout or
retransmits, we first revert the cwnd reduction and congestion
state back to Open state. But we don't raise the cwnd even though
the ACK does not indicate any congestion.
To fix this problem we should first call tcp_fastretrans_alert() to
process the dubious ACK and update the congestion state, then call
tcp_may_raise_cwnd() that raises cwnd based on the current state.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original design slow start is only used to raise cwnd
when cwnd is stricly below ssthresh. It makes little sense
to slow start when cwnd == ssthresh: especially
when hystart has set ssthresh in the initial ramp, or after
recovery when cwnd resets to ssthresh. Not doing so will
also help reduce the buffer bloat slightly.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to test the slow start condition in various congestion
control modules and other places. This is to prepare a slight improvement
in policy as to exactly when to slow start.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
V1 of this patch contains Eric Dumazet's suggestion to move the per
dst RTAX_QUICKACK check into tcp_in_quickack_mode(). Thanks Eric.
I ran some tests and after setting the "ip route change quickack 1"
knob there were still many delayed ACKs sent. This occured
because when icsk_ack.quick=0 the !icsk_ack.pingpong value is
subsequently ignored as tcp_in_quickack_mode() checks both these
values. The condition for a quick ack to trigger requires
that both icsk_ack.quick != 0 and icsk_ack.pingpong=0. Currently
only icsk_ack.pingpong is controlled by the knob. But the
icsk_ack.quick value changes dynamically depending on heuristics.
The crux of the matter is that delayed acks still cannot be entirely
disabled even with the RTAX_QUICKACK per dst knob enabled. This
patch ensures that a quick ack is always sent when the RTAX_QUICKACK
per dst knob is turned on.
The "ip route change quickack 1" knob was recently added to enable
quickacks. It was modeled around the TCP_QUICKACK setsockopt() option.
This issue is that even with "ip route change quickack 1" enabled
we still see delayed ACKs under some conditions. It would be nice
to be able to completely disable delayed ACKs.
Here is an example:
# netstat -s|grep dela
3 delayed acks sent
For all routes enable the knob
# ip route change quickack 1
Generate some traffic across a slow link and we still see the delayed
acks.
# netstat -s|grep dela
106 delayed acks sent
1 delayed acks further delayed because of locked socket
The issue is that both the "ip route change quickack 1" knob and
the TCP_QUICKACK option set the icsk_ack.pingpong variable to 0.
However at the business end in the __tcp_ack_snd_check() routine,
tcp_in_quickack_mode() checks that both icsk_ack.quick != 0
and icsk_ack.pingpong=0 in order to trigger a quickack. As
icsk_ack.quick is determined by heuristics it can be 0. When
that occurs the icsk_ack.pingpong value is ignored and a delayed
ACK is sent regardless.
This patch moves the RTAX_QUICKACK per dst check into the
tcp_in_quickack_mode() routine which ensures that a quickack is
always sent when the quickack knob is enabled for that dst.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree. This batch
mostly comes with patches to address fallout from the previous merge window
cycle, they are:
1) Use entry->state.hook_list from nf_queue() instead of the global nf_hooks
which is not valid when used from NFPROTO_NETDEV, this should cause no
problems though since we have no userspace queueing for that family, but
let's fix this now for the sake of correctness. Patch from Eric W. Biederman.
2) Fix compilation breakage in bridge netfilter if CONFIG_NF_DEFRAG_IPV4 is not
set, from Bernhard Thaler.
3) Use percpu jumpstack in arptables too, now that there's a single copy of the
rule blob we can't store the return address there anymore. Patch from
Florian Westphal.
4) Fix a skb leak in the xmit path of bridge netfilter, problem there since
2.6.37 although it should be not possible to hit invalid traffic there, also
from Florian.
5) Eric Leblond reports that when loading a large ruleset with many missing
modules after a fresh boot, nf_tables can take long time commit it. Fix this
by processing the full batch until the end, even on missing modules, then
abort only once and restart processing.
6) Add bridge netfilter files to the MAINTAINER files.
7) Fix a net_device refcount leak in the new IPV6 bridge netfilter code, from
Julien Grall.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This kernel patch exports the value of the new
ignore_routes_with_linkdown via netconf.
v2: changes to notify userspace via netlink when sysctl values change
and proposed for 'net' since this could be considered a bugfix
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Suggested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frag needed should be sent only if the inner header asked
to not fragment. Currently fragmentation is broken if the
tunnel has df set, but df was not asked in the original
packet. The tunnel's df needs to be still checked to update
internally the pmtu cache.
Commit 23a3647bc4 broke it, and this commit fixes
the ipv4 df check back to the way it was.
Fixes: 23a3647bc4 ("ip_tunnels: Use skb-len to PMTU check.")
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PRR slow start is often too aggressive especially when drops are
caused by traffic policers. The policers mainly use token bucket
to enforce the rate so sending (twice) faster than the delivery
rate causes excessive drops.
This patch changes PRR to the conservative reduction bound
(CRB) mode in RFC 6937 by default. CRB follows the packet
conservation rule to send at most the delivery rate by default.
But if many packets are lost and the pipe is empty, CRB may take N
round trips to repair N losses. We conditionally turn on slow start
mode if all these conditions are made to speed up the recovery:
1) on the second round or later in recovery
2) retransmission sent in the previous round is delivered on this ACK
3) no retransmission is marked lost on this ACK
By using packet conservation by default, this change reduces the loss
retransmits signicantly on networks that deploy traffic policers,
up to 20% reduction of overall loss rate.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the retransmission in CA_Loss is lost again, we should not
continue to slow start or raise cwnd in congestion avoidance mode.
Instead we should enter fast recovery and use PRR to reduce cwnd,
following the principle in RFC5681:
"... or the loss of a retransmission, should be taken as two
indications of congestion and, therefore, cwnd (and ssthresh) MUST
be lowered twice in this case."
This is especially important to reduce loss when the CA_Loss
state was caused by a traffic policer dropping the entire inflight.
The CA_Loss state has a problem where a loss of L packets causes the
sender to send a burst of L packets. So a policer that's dropping
most packets in a given RTT can cause a huge retransmit storm. By
contrast, PRR includes logic to bound the number of outbound packets
that result from a given ACK. So switching to CA_Recovery on lost
retransmits in CA_Loss avoids this retransmit storm problem when
in CA_Loss.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KDJO
-----END PGP SIGNATURE-----
Merge tag 'module_init-alternate_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_init replacement part two from Paul Gortmaker:
"Replace module_init with appropriate alternate initcall in non
modules.
This series converts non-modular code that is using the module_init()
call to hook itself into the system to instead use one of our
alternate priority initcalls.
Unlike the previous series that used device_initcall and hence was a
runtime no-op, these commits change to one of the alternate initcalls,
because (a) we have them and (b) it seems like the right thing to do.
For example, it would seem logical to use arch_initcall for arch
specific setup code and fs_initcall for filesystem setup code.
This does mean however, that changes in the init ordering will be
taking place, and so there is a small risk that some kind of implicit
init ordering issue may lie uncovered. But I think it is still better
to give these ones sensible priorities than to just assign them all to
device_initcall in order to exactly preserve the old ordering.
Thad said, we have already made similar changes in core kernel code in
commit c96d6660dc ("kernel: audit/fix non-modular users of
module_init in core code") without any regressions reported, so this
type of change isn't without precedent. It has also got the same
local testing and linux-next coverage as all the other pull requests
that I'm sending for this merge window have got.
Once again, there is an unused module_exit function removal that shows
up as an outlier upon casual inspection of the diffstat"
* tag 'module_init-alternate_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
x86: perf_event_intel_pt.c: use arch_initcall to hook in enabling
x86: perf_event_intel_bts.c: use arch_initcall to hook in enabling
mm/page_owner.c: use late_initcall to hook in enabling
lib/list_sort: use late_initcall to hook in self tests
arm: use subsys_initcall in non-modular pl320 IPC code
powerpc: don't use module_init for non-modular core hugetlb code
powerpc: use subsys_initcall for Freescale Local Bus
x86: don't use module_init for non-modular core bootflag code
netfilter: don't use module_init/exit in core IPV4 code
fs/notify: don't use module_init for non-modular inotify_user code
mm: replace module_init usages with subsys_initcall in nommu.c
commit 482cfc3185 ("netfilter: xtables: avoid percpu ruleset duplication")
Unlike ip and ip6tables, arp tables were never converted to use the percpu
jump stack.
It still uses the rule blob to store return address, which isn't safe
anymore since we now share this blob among all processors.
Because there is no TEE support for arptables, we don't need to cope
with reentrancy, so we can use loocal variable to hold stack offset.
Fixes: 482cfc3185 ("netfilter: xtables: avoid percpu ruleset duplication")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Conflicts:
drivers/net/ethernet/mellanox/mlx4/main.c
net/packet/af_packet.c
Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
For AF_INET6 sockets, the value of struct ipv6_pinfo.ipv6only is
exported to userspace. It indicates whether a socket bound to in6addr_any
listens on IPv4 as well as IPv6. Since the socket is natively IPv6, it is not
listed by e.g. 'ss -l -4'.
This patch is accompanied by an appropriate one for iproute2 to enable
the additional information in 'ss -e'.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is only enabled with the new per-interface or ipv4 global
sysctls called 'ignore_routes_with_linkdown'.
net.ipv4.conf.all.ignore_routes_with_linkdown = 0
net.ipv4.conf.default.ignore_routes_with_linkdown = 0
net.ipv4.conf.lo.ignore_routes_with_linkdown = 0
...
When the above sysctls are set, will report to userspace that a route is
dead and will no longer resolve to this nexthop when performing a fib
lookup. This will signal to userspace that the route will not be
selected. The signalling of a RTNH_F_DEAD is only passed to userspace
if the sysctl is enabled and link is down. This was done as without it
the netlink listeners would have no idea whether or not a nexthop would
be selected. The kernel only sets RTNH_F_DEAD internally if the
interface has IFF_UP cleared.
With the new sysctl set, the following behavior can be observed
(interface p8p1 is link-down):
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1 dead linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1 dead linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
90.0.0.1 via 70.0.0.2 dev p7p1 src 70.0.0.1
cache
local 80.0.0.1 dev lo src 80.0.0.1
cache <local>
80.0.0.2 via 10.0.5.2 dev p9p1 src 10.0.5.15
cache
While the route does remain in the table (so it can be modified if
needed rather than being wiped away as it would be if IFF_UP was
cleared), the proper next-hop is chosen automatically when the link is
down. Now interface p8p1 is linked-up:
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
192.168.56.0/24 dev p2p1 proto kernel scope link src 192.168.56.2
90.0.0.1 via 80.0.0.2 dev p8p1 src 80.0.0.1
cache
local 80.0.0.1 dev lo src 80.0.0.1
cache <local>
80.0.0.2 dev p8p1 src 80.0.0.1
cache
and the output changes to what one would expect.
If the sysctl is not set, the following output would be expected when
p8p1 is down:
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1 linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1 linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
Since the dead flag does not appear, there should be no expectation that
the kernel would skip using this route due to link being down.
v2: Split kernel changes into 2 patches, this actually makes a
behavioral change if the sysctl is set. Also took suggestion from Alex
to simplify code by only checking sysctl during fib lookup and
suggestion from Scott to add a per-interface sysctl.
v3: Code clean-ups to make it more readable and efficient as well as a
reverse path check fix.
v4: Drop binary sysctl
v5: Whitespace fixups from Dave
v6: Style changes from Dave and checkpatch suggestions
v7: One more checkpatch fixup
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a fib flag called RTNH_F_LINKDOWN to any ipv4 nexthops that are
reachable via an interface where carrier is off. No action is taken,
but additional flags are passed to userspace to indicate carrier status.
This also includes a cleanup to fib_disable_ip to more clearly indicate
what event made the function call to replace the more cryptic force
option previously used.
v2: Split out kernel functionality into 2 patches, this patch simply
sets and clears new nexthop flag RTNH_F_LINKDOWN.
v3: Cleanups suggested by Alex as well as a bug noticed in
fib_sync_down_dev and fib_sync_up when multipath was not enabled.
v5: Whitespace and variable declaration fixups suggested by Dave.
v6: Style fixups noticed by Dave; ran checkpatch to be sure I got them
all.
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP messages can trigger ICMP and local errors. In this case
serr->port is 0 and starting from Linux 4.0 we do not return
the original target address to the error queue readers.
Add function to define which errors provide addr_offset.
With this fix my ping command is not silent anymore.
Fixes: c247f0534c ("ip: fix error queue empty skb handling")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_diag_dump_reqs() is called from inet_diag_dump_icsk() with BH
disabled. So no need to disable BH in inet_diag_dump_reqs().
Signed-off-by: Hiroaki Shimoda <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.2:
API:
- Convert RNG interface to new style.
- New AEAD interface with one SG list for AD and plain/cipher text.
All external AEAD users have been converted.
- New asymmetric key interface (akcipher).
Algorithms:
- Chacha20, Poly1305 and RFC7539 support.
- New RSA implementation.
- Jitter RNG.
- DRBG is now seeded with both /dev/random and Jitter RNG. If kernel
pool isn't ready then DRBG will be reseeded when it is.
- DRBG is now the default crypto API RNG, replacing krng.
- 842 compression (previously part of powerpc nx driver).
Drivers:
- Accelerated SHA-512 for arm64.
- New Marvell CESA driver that supports DMA and more algorithms.
- Updated powerpc nx 842 support.
- Added support for SEC1 hardware to talitos"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (292 commits)
crypto: marvell/cesa - remove COMPILE_TEST dependency
crypto: algif_aead - Temporarily disable all AEAD algorithms
crypto: af_alg - Forbid the use internal algorithms
crypto: echainiv - Only hold RNG during initialisation
crypto: seqiv - Add compatibility support without RNG
crypto: eseqiv - Offer normal cipher functionality without RNG
crypto: chainiv - Offer normal cipher functionality without RNG
crypto: user - Add CRYPTO_MSG_DELRNG
crypto: user - Move cryptouser.h to uapi
crypto: rng - Do not free default RNG when it becomes unused
crypto: skcipher - Allow givencrypt to be NULL
crypto: sahara - propagate the error on clk_disable_unprepare() failure
crypto: rsa - fix invalid select for AKCIPHER
crypto: picoxcell - Update to the current clk API
crypto: nx - Check for bogus firmware properties
crypto: marvell/cesa - add DT bindings documentation
crypto: marvell/cesa - add support for Kirkwood and Dove SoCs
crypto: marvell/cesa - add support for Orion SoCs
crypto: marvell/cesa - add allhwsupport module parameter
crypto: marvell/cesa - add support for all armada SoCs
...
This patch adds NLM_F_APPEND flag to struct nlmsg_hdr->nlmsg_flags
in newroute notifications if the route add was an append.
(This is similar to how NLM_F_REPLACE is already part of new
route replace notifications today)
This helps userspace determine if the route add operation was
an append.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an inet_sock is destroyed, its source port (sk_num) is set to
zero as part of the unhash procedure. In order to supply a source
port as part of the NETLINK_SOCK_DIAG socket destruction broadcasts,
the source port number must be read from inet_sport instead.
Tested: ss -E
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the mvebu/drivers branch of the arm-soc tree which contains
just a single patch bfa1ce5f38 ("bus:
mvebu-mbus: add mv_mbus_dram_info_nooverlap()") that happens to be
a prerequisite of the new marvell/cesa crypto driver.
The file net/ipv4/netfilter.o is created based on whether
CONFIG_NETFILTER is set. However that is defined as a bool, and
hence this file with the core netfilter hooks will never be
modular. So using module_init as an alias for __initcall can be
somewhat misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing. Also add an inclusion of init.h, as
that was previously implicit here in the netfilter.c file.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of subsys_initcall (which
seems to make sense for netfilter code) will thus change this
registration from level 6-device to level 4-subsys (i.e. slightly
earlier). However no observable impact of that small difference
has been observed during testing, or is expected. (i.e. the
location of the netfilter messages in dmesg remains unchanged
with respect to all the other surrounding messages.)
As for the module_exit, rather than replace it with __exitcall,
we simply remove it, since it appears only UML does anything
with those, and even for UML, there is no relevant cleanup
to be done here.
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netfilter-devel@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This get_info handler will simply dispatch to the appropriate
existing inet protocol handler.
This patch also includes a new netlink attribute
(INET_DIAG_PROTOCOL). This attribute is currently only used
for multicast messages. Without this attribute, there is no
way of knowing the IP protocol used by the socket information
being broadcast. This attribute is not necessary in the 'dump'
variant of this protocol (though it could easily be added)
because dump requests are issued for specific family/protocol
pairs.
Tested: ss -E (note, the -E option has not yet been merged into
the upstream version of ss).
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, there was no clear distinction between the inet protocols
that used struct tcp_info to report information and those that didn't.
This change adds a specific size attribute to the inet_diag_handler
struct which defines these interfaces. This will make dispatching
sock_diag get_info requests identical for all inet protocols in a
following patch.
Tested: ss -au
Tested: ss -at
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
This a bit large (and late) patchset that contains Netfilter updates for
net-next. Most relevantly br_netfilter fixes, ipset RCU support, removal of
x_tables percpu ruleset copy and rework of the nf_tables netdev support. More
specifically, they are:
1) Warn the user when there is a better protocol conntracker available, from
Marcelo Ricardo Leitner.
2) Fix forwarding of IPv6 fragmented traffic in br_netfilter, from Bernhard
Thaler. This comes with several patches to prepare the change in first place.
3) Get rid of special mtu handling of PPPoE/VLAN frames for br_netfilter. This
is not needed anymore since now we use the largest fragment size to
refragment, from Florian Westphal.
4) Restore vlan tag when refragmenting in br_netfilter, also from Florian.
5) Get rid of the percpu ruleset copy in x_tables, from Florian. Plus another
follow up patch to refine it from Eric Dumazet.
6) Several ipset cleanups, fixes and finally RCU support, from Jozsef Kadlecsik.
7) Get rid of parens in Netfilter Kconfig files.
8) Attach the net_device to the basechain as opposed to the initial per table
approach in the nf_tables netdev family.
9) Subscribe to netdev events to detect the removal and registration of a
device that is referenced by a basechain.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After Florian patches, there is no need for XT_TABLE_INFO_SZ anymore :
Only one copy of table is kept, instead of one copy per cpu.
We also can avoid a dereference if we put table data right after
xt_table_info. It reduces register pressure and helps compiler.
Then, we attempt a kmalloc() if total size is under order-3 allocation,
to reduce TLB pressure, as in many cases, rules fit in 32 KB.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
According to the reporter, they are not needed.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
text data bss dec hex filename
old: 16527 44 0 16571 40bb net/ipv4/ip_output.o
new: 14935 44 0 14979 3a83 net/ipv4/ip_output.o
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We store the rule blob per (possible) cpu. Unfortunately this means we can
waste lot of memory on big smp machines. ipt_entry structure ('rule head')
is 112 byte, so e.g. with maxcpu=64 one single rule eats
close to 8k RAM.
Since previous patch made counters percpu it appears there is nothing
left in the rule blob that needs to be percpu.
On my test system (144 possible cpus, 400k dummy rules) this
change saves close to 9 Gigabyte of RAM.
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The binary arp/ip/ip6tables ruleset is stored per cpu.
The only reason left as to why we need percpu duplication are the rule
counters embedded into ipt_entry et al -- since each cpu has its own copy
of the rules, all counters can be lockless.
The downside is that the more cpus are supported, the more memory is
required. Rules are not just duplicated per online cpu but for each
possible cpu, i.e. if maxcpu is 144, then rule is duplicated 144 times,
not for the e.g. 64 cores present.
To save some memory and also improve utilization of shared caches it
would be preferable to only store the rule blob once.
So we first need to separate counters and the rule blob.
Instead of using entry->counters, allocate this percpu and store the
percpu address in entry->counters.pcnt on CONFIG_SMP.
This change makes no sense as-is; it is merely an intermediate step to
remove the percpu duplication of the rule set in a followup patch.
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
since commit d6b915e29f
("ip_fragment: don't forward defragmented DF packet") the largest
fragment size is available in the IPCB.
Therefore we no longer need to care about 'encapsulation'
overhead of stripped PPPOE/VLAN headers since ip_do_fragment
doesn't use device mtu in such cases.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We had various issues in the past when TCP stack was modifying
gso_size/gso_segs while clones were in flight.
Commit c52e2421f7 ("tcp: must unclone packets before mangling them")
fixed these bugs and added a WARN_ON_ONCE(skb_cloned(skb)); in
tcp_set_skb_tso_segs()
These bugs are now fixed, and because TCP stack now only sets
shinfo->gso_size|segs on the clone itself, the check can be removed.
As a result of this change, compiler inlines tcp_set_skb_tso_segs() in
tcp_init_tso_segs()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit cd7d8498c9 ("tcp: change tcp_skb_pcount() location") we stored
gso_segs in a temporary cache hot location.
This patch does the same for gso_size.
This allows to save 2 cache line misses in tcp xmit path for
the last packet that is considered but not sent because of
various conditions (cwnd, tso defer, receiver window, TSQ...)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_set_skb_tso_segs() & tcp_init_tso_segs() no longer
use the sock pointer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our goal is to touch skb_shinfo(skb) only when absolutely needed,
to avoid two cache line misses in TCP output path for last skb
that is considered but not sent because of various conditions
(cwnd, tso defer, receiver window, TSQ...)
A packet is GSO only when skb_shinfo(skb)->gso_size is not zero.
We can set skb_shinfo(skb)->gso_type to sk->sk_gso_type even for
non GSO packets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_gso_segment() and tcp_gro_receive() are not strictly
part of TCP stack. They should not assume tcp_skb_mss(skb)
is in fact skb_shinfo(skb)->gso_size.
This will allow us to change tcp_skb_mss() in following patches.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAIA Delay-Gradient (CDG) is a TCP congestion control that modifies
the TCP sender in order to [1]:
o Use the delay gradient as a congestion signal.
o Back off with an average probability that is independent of the RTT.
o Coexist with flows that use loss-based congestion control, i.e.,
flows that are unresponsive to the delay signal.
o Tolerate packet loss unrelated to congestion. (Disabled by default.)
Its FreeBSD implementation was presented for the ICCRG in July 2012;
slides are available at http://www.ietf.org/proceedings/84/iccrg.html
Running the experiment scenarios in [1] suggests that our implementation
achieves more goodput compared with FreeBSD 10.0 senders, although it also
causes more queueing delay for a given backoff factor.
The loss tolerance heuristic is disabled by default due to safety concerns
for its use in the Internet [2, p. 45-46].
We use a variant of the Hybrid Slow start algorithm in tcp_cubic to reduce
the probability of slow start overshoot.
[1] D.A. Hayes and G. Armitage. "Revisiting TCP congestion control using
delay gradients." In Networking 2011, pages 328-341. Springer, 2011.
[2] K.K. Jonassen. "Implementing CAIA Delay-Gradient in Linux."
MSc thesis. Department of Informatics, University of Oslo, 2015.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: David Hayes <davihay@ifi.uio.no>
Cc: Andreas Petlund <apetlund@simula.no>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Nicolas Kuhn <nicolas.kuhn@telecom-bretagne.eu>
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upcoming tcp_cdg uses tcp_enter_cwr() to initiate PRR. Export this
function so that CDG can be compiled as a module.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: David Hayes <davihay@ifi.uio.no>
Cc: Andreas Petlund <apetlund@simula.no>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Nicolas Kuhn <nicolas.kuhn@telecom-bretagne.eu>
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dctcp_alpha can be read by from dctcp_get_info() without
synchro, so use WRITE_ONCE() to prevent compiler from using
dctcp_alpha as a temporary variable.
Also, playing with small dctcp_shift_g (like 1), can expose
an overflow with 32bit values shifted 9 times before divide.
Use an u64 field to avoid this problem, and perform the divide
only if acked_bytes_ecn is not zero.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Alexander Duyck pointed out that:
struct tnode {
...
struct key_vector kv[1];
}
The kv[1] member of struct tnode is an arry that refernced by
a null pointer will not crash the system, like this:
struct tnode *p = NULL;
struct key_vector *kv = p->kv;
As such p->kv doesn't actually dereference anything, it is simply a
means for getting the offset to the array from the pointer p.
This patch make the code more regular to avoid making people feel
odd when they look at the code.
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 and IPv6 share same implementation of get_cookie_sock(),
and there is no point inlining it.
We add tcp_ prefix to the common helper name and export it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For same reasons than in commit 12e25e1041 ("tcp: remove redundant
checks"), we can remove redundant checks done for timewait sockets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an application needs to force a source IP on an active TCP socket
it has to use bind(IP, port=x).
As most applications do not want to deal with already used ports, x is
often set to 0, meaning the kernel is in charge to find an available
port.
But kernel does not know yet if this socket is going to be a listener or
be connected.
It has very limited choices (no full knowledge of final 4-tuple for a
connect())
With limited ephemeral port range (about 32K ports), it is very easy to
fill the space.
This patch adds a new SOL_IP socket option, asking kernel to ignore
the 0 port provided by application in bind(IP, port=0) and only
remember the given IP address.
The port will be automatically chosen at connect() time, in a way
that allows sharing a source port as long as the 4-tuples are unique.
This new feature is available for both IPv4 and IPv6 (Thanks Neal)
Tested:
Wrote a test program and checked its behavior on IPv4 and IPv6.
strace(1) shows sequences of bind(IP=127.0.0.2, port=0) followed by
connect().
Also getsockname() show that the port is still 0 right after bind()
but properly allocated after connect().
socket(PF_INET, SOCK_STREAM, IPPROTO_IP) = 5
setsockopt(5, SOL_IP, IP_BIND_ADDRESS_NO_PORT, [1], 4) = 0
bind(5, {sa_family=AF_INET, sin_port=htons(0), sin_addr=inet_addr("127.0.0.2")}, 16) = 0
getsockname(5, {sa_family=AF_INET, sin_port=htons(0), sin_addr=inet_addr("127.0.0.2")}, [16]) = 0
connect(5, {sa_family=AF_INET, sin_port=htons(53174), sin_addr=inet_addr("127.0.0.3")}, 16) = 0
getsockname(5, {sa_family=AF_INET, sin_port=htons(38050), sin_addr=inet_addr("127.0.0.2")}, [16]) = 0
IPv6 test :
socket(PF_INET6, SOCK_STREAM, IPPROTO_IP) = 7
setsockopt(7, SOL_IP, IP_BIND_ADDRESS_NO_PORT, [1], 4) = 0
bind(7, {sa_family=AF_INET6, sin6_port=htons(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, 28) = 0
getsockname(7, {sa_family=AF_INET6, sin6_port=htons(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, [28]) = 0
connect(7, {sa_family=AF_INET6, sin6_port=htons(57300), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, 28) = 0
getsockname(7, {sa_family=AF_INET6, sin6_port=htons(60964), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, [28]) = 0
I was able to bind()/connect() a million concurrent IPv4 sockets,
instead of ~32000 before patch.
lpaa23:~# ulimit -n 1000010
lpaa23:~# ./bind --connect --num-flows=1000000 &
1000000 sockets
lpaa23:~# grep TCP /proc/net/sockstat
TCP: inuse 2000063 orphan 0 tw 47 alloc 2000157 mem 66
Check that a given source port is indeed used by many different
connections :
lpaa23:~# ss -t src :40000 | head -10
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 0 127.0.0.2:40000 127.0.202.33:44983
ESTAB 0 0 127.0.0.2:40000 127.2.27.240:44983
ESTAB 0 0 127.0.0.2:40000 127.2.98.5:44983
ESTAB 0 0 127.0.0.2:40000 127.0.124.196:44983
ESTAB 0 0 127.0.0.2:40000 127.2.139.38:44983
ESTAB 0 0 127.0.0.2:40000 127.1.59.80:44983
ESTAB 0 0 127.0.0.2:40000 127.3.6.228:44983
ESTAB 0 0 127.0.0.2:40000 127.0.38.53:44983
ESTAB 0 0 127.0.0.2:40000 127.1.197.10:44983
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xen virtual network driver has higher latency than a physical NIC.
Having only 128K as limit for TSQ introduced 30% regression in guest
throughput.
This patch raises the limit to 256K. This reduces the regression to 8%.
This buys us more time to work out a proper solution in the long run.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_v4_rcv() checks the following before calling tcp_v4_do_rcv():
if (th->doff < sizeof(struct tcphdr) / 4)
goto bad_packet;
if (!pskb_may_pull(skb, th->doff * 4))
goto discard_it;
So following check in tcp_v4_do_rcv() is redundant
and "goto csum_err;" is wrong anyway.
if (skb->len < tcp_hdrlen(skb) || ...)
goto csum_err;
A second check can be removed after no_tcp_socket label for same reason.
Same tests can be removed in tcp_v6_do_rcv()
Note : short tcp frames are not properly accounted in tcpInErrs MIB,
because pskb_may_pull() failure simply drops incoming skb, we might
fix this in a separate patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
