The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to cmd64x_tune_pio(), making it return the mode set,
and "wrapping" the new tuneproc() method around it; while at it, also get rid
of the non-working prefetch control code (filtering out related argument values
in the "wrapper"), remove redundant PIO5 mode limitation, make cmdprintk() give
more sensible mode info, and remove mention about the obsolete /proc/ interface.
Get rid of the broken config_chipset_for_pio() which always tried to set PIO4,
switch to always auto-tuning PIO instead.
Oh, and add the missing PIO5 support to the speedproc() method while at it. :-)
Warning: compile tested only -- getting to the real hardware isn't that easy...
On Tuesday 06 February 2007 22:11, Mikael Pettersson <mikpe@it.uu.se> wrote:
>
> Worked fine on my SPARC Ultra5 with a CMD646 IDE controller.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to ali15x3_tune_pio() and "wrapping" the new tuneproc()
method around it and making it return the mode set, update the heading comment.
Also, setting PIO mode via the speedproc() method does not work due to passing
to the tuneproc() method's a mode number not biased by XFER_PIO_0 -- fix this
along with a typo in the heading comment...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The information contained within platform_data should be self-contained.
Replace the pointer to a MAC address with the actual MAC address in
struct mv643xx_eth_platform_data.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit 908b637fe7 removed ETH_DMA_ALIGN
but missed a usage of it in a macro, which broke the build.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This missing line caused transmit errors on the Qlogic 4032 chip.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix copyright and license ("regents" should not have ever been used).
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No need to stop tc35815 before resetting the board. This fixes the
build of tc35815 as a module. This also means there is no caller of
tc35815_killall left, so remove that function also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Conditionalize all PM related stuff in libata core layer using
CONFIG_PM.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add missing #ifdef CONFIG_PM conditionals around all PM related parts
in libata LLDs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some LLDs were missing scsi device PM callbacks while having host/port
suspend support. Add missing ones.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If you'll recall, over a year ago, I pointed out that the current
Radeon driver erroneously returns -EINVAL for valid blanking codes,
here is a link to that thread:
http://lkml.org/lkml/2006/1/28/6
No other driver does this, and it confuses the X server into thinking
that the device does not support blanking properly.
I looked again and there is simply no reason for the Radeon driver to
return -EINVAL for FB_BLANK_NORMAL. It claims it wants to do this in
order to convince fbcon to blank in software, right here:
if (fb_blank(info, blank))
fbcon_generic_blank(vc, info, blank);
to software blank the screen. But it only causes that to happen
in the FB_BLANK_NORMAL case.
That makes no sense because the Radeon code does this:
val |= CRTC_DISPLAY_DIS;
in the FB_BLANK_NORMAL case so should be blanking the hardware, and
there is therefore no reason to SW blank by returning -EINVAL.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Antonino Daplas <adaplas@gmail.com>
We mistakedly modify 'bus' in the innermost loop. What
should happen is that at each register index iteration,
we start with the same 'bus'.
So preserve it's value at the top level, and use a loop
local variable 'dbus' for iteration.
This bug causes registers other than the first to be
decoded improperly.
Signed-off-by: David S. Miller <davem@davemloft.net>
The QDI init code contains some bugs which mean it only works if you have
a test setup that causes both a successful and failed probe. Fix this
Found by Philip Guo
(Who found it working on code analysis tools not running VLB IDE
controllers)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox noticed several hooks in pata_* drivers were missing, when
he authored his ->cable_detect hook patches. This patch extracts
just those fixes from Alan's patches, adding the necessary hooks
(usually ->freeze, ->thaw, and ->post_internal_cmd) to the drivers.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2.6.21-rc has horrible problems with libata and PATA cable types (and
thus speeds). This occurs because Tejun fixed a pile of other bugs and
we now do cable detect enforcement for drive side detection properly.
Unfortunately we don't do the process around cable detection right. Tejun
identified the problem and pointed to the right Annex in the spec, this patch
implements the needed changes.
The basic requirement is that we have to identify the slave before the
master.
The patch switches the identify order so that we can do the drive side
detection correctly.
[NOTE: patch and description extracted from a larger work written
and signed-off-by Alan Cox]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The initial simplex handling code is fooled if you suspend and resume.
This also causes problems with some single channel controllers which
claim to be simplex.
The fix is fairly simple, instead of keeping a flag to remember if we
gave away the simplex channel we remember the actual owner. As the owner
is always part of the host_set we don't even need a refcount.
Knowing the owner also means we can reassign simplex DMA channels in
future hotplug code etc if we need to
Signed-off-by: Alan Cox <alan@redhat.com>
(and a signed-off for the patch I sent before while I remember)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: improve spurious SDB FIS handling
ahci/pata_jmicron: match class not function number
jmicron ATA: reimplement jmicron ATA quirk
pata_jmicron: drop unnecessary device programming in [re]init
libata: blacklist FUJITSU MHT2060BH for NCQ
sata_sil24: kill unused local variable idx in sil24_fill_sg()
libata: clear drvdata in ata_host_release(), take#2
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
HID: fix Logitech DiNovo Edge touchwheel and Logic3 /SpectraVideo middle button
HID: add git tree information to MAINTAINERS
HID: fix broken Logitech S510 keyboard report descriptor; make extra keys work
HID: fix possible double-free on error path in hid parser
HID: hid-debug.c should #include <linux/hid-debug.h>
HID: fix bug in zeroing the last field byte in output reports
USB HID: use CONFIG_HID_DEBUG for outputting report descriptor
USB HID: Fix USB vendor and product IDs endianness for USB HID devices
Spurious SDB FIS during NCQ might not contain spurious completions.
It could be spurious TF update or invalid async notification. Treat
as HSM violation iff a spurious SDB FIS contains spurious completions;
otherwise, just whine once about it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make jmiron_ata quirk update pdev->class after programming the device
and update ahci and pata_jmicron such that they match class code
instead of checking function number manually. For ahci, it matches
for vendor and class. For pata_jmicron, it matches vendor, device and
class as IDE class isn't as well defined as AHCI class.
This makes jmicron device matching more conventional and script
friendly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement jmicron ATA quirk.
* renamed to quirk_jmicron_ata()
* quirk is invoked only for the affected controllers
* programming is stricter. e.g. conf5 bit24 is cleared if
unnecessary.
* code factored for readability
* JMB360 and JMB368 are programmed into proper mode
Verified on JMB360, 363 and 368.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Channel redirect and AHCI mode enable programmings are done via PCI
quirk for both probe and resume paths. Drop duplicate and possibly
unsafe device programming from pata_jmicron().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch provides the following hugetlb-related fixes to the recent stacked
shm files changes:
- Update is_file_hugepages() so it will reconize hugetlb shm segments.
- get_unmapped_area must be called with the nested file struct to handle
the sfd->file->f_ops->get_unmapped_area == NULL case.
- The fsync f_op must be wrapped since it is specified in the hugetlbfs
f_ops.
This is based on proposed fixes from Eric Biederman that were debugged and
tested by me. Without it, attempting to use hugetlb shared memory segments
on powerpc (and likely ia64) will kill your box.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: William Irwin <bill.irwin@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blacklist FUJITSU MHT2060BH for NCQ. On this drive, NCQ works iff
queue depth is equal to or less than 4. Just turn it off.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mike Accetta <maccetta@laurelnetworks.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kill unused local variable idx in sil24_fill_sg().
Spotted by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clearing drvdata in ->remove_one causes NULL pointer deference. Clear
drvdata only in ata_host_release() after all resources are freed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix invalidate_inode_pages2_range() so that it does not immediately exit
just because a single page in the specified range could not be removed.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a possible race that leads to double freeing an idr index.
When the master begin to close, release_dev() is called and then
pty_close() is called:
if (tty->driver->close)
tty->driver->close(tty, filp);
This is done without helding any locks other than BKL. Inside pty_close(),
being a master close, the devpts entry will be removed:
#ifdef CONFIG_UNIX98_PTYS
if (tty->driver == ptm_driver)
devpts_pty_kill(tty->index);
#endif
But devpts_pty_kill() will call get_node() that may sleep while waiting for
&devpts_root->d_inode->i_sem. When this happens and the slave is being
opened, tty_open() just found the driver and index:
driver = get_tty_driver(device, &index);
if (!driver) {
mutex_unlock(&tty_mutex);
return -ENODEV;
}
This part of the code is already protected under tty_mute. The problem is
that the slave close already got an index. Then init_dev() is called and
blocks waiting for the same &devpts_root->d_inode->i_sem.
When the master close resumes, it removes the devpts entry, and the
relation between idr index and the tty is gone. The master then sleeps
waiting for the tty_mutex on release_dev().
Slave open resumes and found no tty for that index. As result, a NULL tty
is returned and init_dev() doesn't flow to fast_track:
/* check whether we're reopening an existing tty */
if (driver->flags & TTY_DRIVER_DEVPTS_MEM) {
tty = devpts_get_tty(idx);
if (tty && driver->subtype == PTY_TYPE_MASTER)
tty = tty->link;
} else {
tty = driver->ttys[idx];
}
if (tty) goto fast_track;
The result of this, is that a new tty will be created and init_dev() returns
sucessfull. After returning, tty_mutex is dropped and master close may resume.
Master close finds it's the only use and both sides are closing, then releases
the tty and the index. At this point, the idr index is free, but slave still
has it.
Slave open then calls pty_open() and finds that tty->link->count is 0,
because there's no master and returns error. Then tty_open() calls
release_dev() which executes without any warning, as it was a case of last
slave close when the master is already closed (master->count == 0,
slave->count == 1). The tty is then released with the already released idr
index.
This normally would only issue a warning on idr_remove() but in case of a
customer's critical application, it's never too simple:
thread1: opens master, gets index X
thread1: begin closing master
thread2: begin opening slave with index X
thread1: finishes closing master, index X released
thread3: opens master, gets index X, just released
thread2: fails opening slave, releases index X <----
thread4: opens master, gets index X, init_dev() then find an already in use
and healthy tty and fails
If no more indexes are released, ptmx_open() will keep failing, as the
first free index available is X, and it will make init_dev() fail because
you're trying to "reopen a master" which isn't valid.
The patch notices when this race happens and make init_dev() fail
imediately. The init_dev() function is called with tty_mutex held, so it's
safe to continue with tty till the end of function because release_dev()
won't make any further changes without grabbing the tty_mutex.
Without the patch, on some machines it's possible get easily idr warnings
like this one:
idr_remove called for id=15 which is not allocated.
[<c02555b9>] idr_remove+0x139/0x170
[<c02a1b62>] release_mem+0x182/0x230
[<c02a28e7>] release_dev+0x4b7/0x700
[<c02a0ea7>] tty_ldisc_enable+0x27/0x30
[<c02a1e64>] init_dev+0x254/0x580
[<c02a0d64>] check_tty_count+0x14/0xb0
[<c02a4f05>] tty_open+0x1c5/0x340
[<c02a4d40>] tty_open+0x0/0x340
[<c017388f>] chrdev_open+0xaf/0x180
[<c017c2ac>] open_namei+0x8c/0x760
[<c01737e0>] chrdev_open+0x0/0x180
[<c0167bc9>] __dentry_open+0xc9/0x210
[<c0167e2c>] do_filp_open+0x5c/0x70
[<c0167a91>] get_unused_fd+0x61/0xd0
[<c0167e93>] do_sys_open+0x53/0x100
[<c0167f97>] sys_open+0x27/0x30
[<c010303b>] syscall_call+0x7/0xb
using this test application available on:
http://www.ruivo.org/~aris/pty_sodomizer.c
Signed-off-by: Aristeu Sergio Rozanski Filho <aris@ruivo.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When it goes to free1_out, dev->dma_mem has not been freed.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CAPI trace debug functions were using a fixed size buffer, which can be
overflowed if wrong formatted CAPI messages were sent to the kernel capi
layer. The code was also not protected against multiple callers. This fix
bug 8028.
Additionally the patch make the CAPI trace functions optional.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
page_lock_anon_vma() uses spin_lock() to block RCU. This doesn't work with
PREEMPT_RCU, we have to do rcu_read_lock() explicitely. Otherwise, it is
theoretically possible that slab returns anon_vma's memory to the system
before we do spin_unlock(&anon_vma->lock).
[ Hugh points out that this only matters for PREEMPT_RCU, which isn't merged
yet, and may never be. Regardless, this patch is conceptually the
right thing to do, even if it doesn't matter at this point. - Linus ]
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Describes how/when the information exported to `/proc/stat' is calculated,
and possible problems with this approach.
Signed-off-by: Vassili Karpov <av1474@comtv.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SMT scheduler incorrectly skips kernel threads even if they are
runnable (but they are preempted by a higher-prio user-space task which got
SMT-delayed by an even higher-priority task running on a sibling CPU).
Fix this for now by only doing the SMT-nice optimization if the
to-be-delayed task is the only runnable task. (This should cover most of
the real-life cases anyway.)
This bug has been in the SMT scheduler since 2.6.17 or so, but has only
been noticed now by the active check in the dynticks code.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3: Introduce CONFIG_PS3_ADVANCED, as suggested by Roman Zippel, and use
it to control questions about PS3 subsystems that may not be obvious for
the casual user.
This gets rid of the following warning on non-powerpc platforms: |
drivers/video/Kconfig:1604:warning: 'select' used by config symbol 'FB_PS3'
refer to undefined symbol 'PS3_PS3AV'
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are race issues around ext[34] xattr block release code.
ext[34]_xattr_release_block() checks the reference count of xattr block
(h_refcount) and frees that xattr block if it is the last one reference it.
Unlike ext2, the check of this counter is unprotected by any lock.
ext[34]_xattr_release_block() will free the mb_cache entry before freeing
that xattr block. There is a small window between the check for the re
h_refcount ==1 and the call to mb_cache_entry_free(). During this small
window another inode might find this xattr block from the mbcache and reuse
it, racing a refcount updates. The xattr block will later be freed by the
first inode without notice other inode is still use it. Later if that
block is reallocated as a datablock for other file, then more serious
problem might happen.
We need put a lock around places checking the refount as well to avoid
racing issue. Another place need this kind of protection is in
ext3_xattr_block_set(), where it will modify the xattr block content in-
the-fly if the refcount is 1 (means it's the only inode reference it).
This will also fix another issue: the xattr block may not get freed at all
if no lock is to protect the refcount check at the release time. It is
possible that the last two inodes could release the shared xattr block at
the same time. But both of them think they are not the last one so only
decreased the h_refcount without freeing xattr block at all.
We need to call lock_buffer() after ext3_journal_get_write_access() to
avoid deadlock (because the later will call lock_buffer()/unlock_buffer
() as well).
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Cc: Andreas Gruenbacher <agruen@suse.de>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
