Process receive event from same process by default. Add a flag to be
able to receive event from all processes, this requires super user
permission.
Event using pid 0 to send the event to all processes, to keep the
default behavior of existing SMI events.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Define new system management interface event IDs for migration, GPU
recoverable page fault, user queues eviction, restore and unmap from
GPU events and corresponding event triggers, those will be implemented
in the following patches.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX10 and up have work group processors (WGP) and WGP mode is the native
compile mode.
KFD and ROCr have no visibility into whether a dispatch is operating
in CU or WGP mode.
Enforce CU masking to be pairwise continguous in enablement and
round robin distribute CUs across the SEs in a pairwise manner to
assume WGP mode at all times.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Both PSFP stats and the port stats read by ocelot_check_stats_work() are
indirectly read through the same mechanism - write to STAT_CFG:STAT_VIEW,
read from SYS:STAT:CNT[n].
It's just that for port stats, we write STAT_VIEW with the index of the
port, and for PSFP stats, we write STAT_VIEW with the filter index.
So if we allow them to run concurrently, ocelot_check_stats_work() may
change the view from vsc9959_psfp_counters_get(), and vice versa.
Fixes: 7d4b564d6a ("net: dsa: felix: support psfp filter on vsc9959")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220629183007.3808130-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric reports that syzbot made short work out of my speculative
fix. Indeed when queue gets detached its tfile->tun remains,
so we would try to stop NAPI twice with a detach(), close()
sequence.
Alternative fix would be to move tun_napi_disable() to
tun_detach_all() and let the NAPI run after the queue
has been detached.
Fixes: a8fc8cb569 ("net: tun: stop NAPI when detaching queues")
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220629181911.372047-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add RaptorLake to the list of processor models supported by the Intel
TCC cooling driver.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
[ rjw: Subject edits, new changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
s390x appears to present two RNG interfaces:
- a "TRNG" that gathers entropy using some hardware function; and
- a "DRBG" that takes in a seed and expands it.
Previously, the TRNG was wired up to arch_get_random_{long,int}(), but
it was observed that this was being called really frequently, resulting
in high overhead. So it was changed to be wired up to arch_get_random_
seed_{long,int}(), which was a reasonable decision. Later on, the DRBG
was then wired up to arch_get_random_{long,int}(), with a complicated
buffer filling thread, to control overhead and rate.
Fortunately, none of the performance issues matter much now. The RNG
always attempts to use arch_get_random_seed_{long,int}() first, which
means a complicated implementation of arch_get_random_{long,int}() isn't
really valuable or useful to have around. And it's only used when
reseeding, which means it won't hit the high throughput complications
that were faced before.
So this commit returns to an earlier design of just calling the TRNG in
arch_get_random_seed_{long,int}(), and returning false in arch_get_
random_{long,int}().
Part of what makes the simplification possible is that the RNG now seeds
itself using the TRNG at bootup. But this only works if the TRNG is
detected early in boot, before random_init() is called. So this commit
also causes that check to happen in setup_arch().
Cc: stable@vger.kernel.org
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Ingo Franzki <ifranzki@linux.ibm.com>
Cc: Juergen Christ <jchrist@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20220610222023.378448-1-Jason@zx2c4.com
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
io_import_iovec uses the s pointer, but this was changed immediately
after the iovec was re-imported and so it was imported into the wrong
place.
Change the ordering.
Fixes: 2be2eb02e2 ("io_uring: ensure reads re-import for selected buffers")
Signed-off-by: Dylan Yudaken <dylany@fb.com>
Link: https://lore.kernel.org/r/20220630132006.2825668-1-dylany@fb.com
[axboe: ensure we don't half-import as well]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull rdma fixes from Jason Gunthorpe:
"Three minor bug fixes:
- qedr not setting the QP timeout properly toward userspace
- Memory leak on error path in ib_cm
- Divide by 0 in RDMA interrupt moderation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
linux/dim: Fix divide by 0 in RDMA DIM
RDMA/cm: Fix memory leak in ib_cm_insert_listen
RDMA/qedr: Fix reporting QP timeout attribute
Pull fanotify fix from Jan Kara:
"A fix for recently added fanotify API to have stricter checks and
refuse some invalid flag combinations to make our life easier in the
future"
* tag 'fsnotify_for_v5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: refine the validation checks on non-dir inode mask
Pull crypto fix from Herbert Xu:
"Fix a regression that breaks the ccp driver"
* tag 'v5.19-p3' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ccp - Fix device IRQ counting by using platform_irq_count()
Display is turned off by i915_drm_suspend() during the suspend
procedure, removing the last reference of some gem objects that were
used by display.
The issue is that those objects are only actually freed when
mm.free_work executed and that can happen very late in the suspend
process causing issues.
So here draining all freed objects released by display fixing suspend
issues.
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220629134721.48375-1-jose.souza@intel.com
Pull devfreq fixes for 5.19-rc5 from Chanwoo Choi:
"1. Fix devfreq passive governor issue when cpufreq policies are not
ready during kernel boot because some CPUs turn on after kernel
booting or others.
- Re-initialize the vairables of struct devfreq_passive_data when
PROBE_DEFER happens when cpufreq_get() returns NULL.
- Use dev_err_probe to mute warning when PROBE_DEFER.
- Fix cpufreq passive unregister erroring on PROBE_DEFER
by using the allocated parent_cpu_data list to free resouce
instead of for_each_possible_cpu().
- Remove duplicate cpufreq passive unregister and warning when
PROBE_DEFER.
- Use HZ_PER_KZH macro in units.h.
- Fix wrong indentation in SPDX-License line.
2. Fix reference count leak in exynos-ppmu.c by using of_node_put().
3. Rework freq_table to be local to devfreq struct
- struct devfreq_dev_profile includes freq_table array to store
the supported frequencies. If devfreq driver doesn't initialize
the freq_table, devfreq core allocates the memory and initializes
the freq_table.
On a devfreq PROBE_DEFER, the freq_table in the driver profile
struct is never reset and may be left in an undefined state. To fix
this and correctly handle PROBE_DEFER, use a local freq_table and
max_state in the devfreq struct."
* tag 'devfreq-fixes-for-5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
PM / devfreq: passive: revert an editing accident in SPDX-License line
PM / devfreq: Fix kernel warning with cpufreq passive register fail
PM / devfreq: Rework freq_table to be local to devfreq struct
PM / devfreq: exynos-ppmu: Fix refcount leak in of_get_devfreq_events
PM / devfreq: passive: Use HZ_PER_KHZ macro in units.h
PM / devfreq: Fix cpufreq passive unregister erroring on PROBE_DEFER
PM / devfreq: Mute warning on governor PROBE_DEFER
PM / devfreq: Fix kernel panic with cpu based scaling to passive gov
We waste a u64 SQE field for flags even though we don't need as many
bits and it can be used for something more useful later. Store io_uring
specific send/recv flags in sqe->ioprio instead of ->addr2.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Fixes: 0455d4ccec ("io_uring: add POLL_FIRST support for send/sendmsg and recv/recvmsg")
[axboe: change comment in io_uring.h as well]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The ddc pin and aux channel sanitization may disable DVI/HDMI and DP,
respectively, of ports parsed earlier, in "last one wins" fashion. With
parsing and printing interleaved, we'll end up logging support first and
disabling later anyway.
Now that we've split ddi port info parsing and printing, take it further
by doing the printing in a separate loop, fixing the logging.
Note that this also changes the logging order from VBT child device
order to port number order.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220621123732.1118437-1-jani.nikula@intel.com
In mlxsw_sp_nexthop6_init(), a next hop is always added to the router
linked list, and mlxsw_sp_nexthop_type_init() is invoked afterwards. When
that function results in an error, the next hop will not have been removed
from the linked list. As the error is propagated upwards and the caller
frees the next hop object, the linked list ends up holding an invalid
object.
A similar issue comes up with mlxsw_sp_nexthop4_init(), where rollback
block does exist, however does not include the linked list removal.
Both IPv6 and IPv4 next hops have a similar issue with next-hop counter
rollbacks. As these were introduced in the same patchset as the next hop
linked list, include the cleanup in this patch.
Fixes: dbe4598c1e ("mlxsw: spectrum_router: Keep nexthops in a linked list")
Fixes: a5390278a5 ("mlxsw: spectrum: Add support for setting counters on nexthops")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220629070205.803952-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are UAF bugs in rose_heartbeat_expiry(), rose_timer_expiry()
and rose_idletimer_expiry(). The root cause is that del_timer()
could not stop the timer handler that is running and the refcount
of sock is not managed properly.
One of the UAF bugs is shown below:
(thread 1) | (thread 2)
| rose_bind
| rose_connect
| rose_start_heartbeat
rose_release | (wait a time)
case ROSE_STATE_0 |
rose_destroy_socket | rose_heartbeat_expiry
rose_stop_heartbeat |
sock_put(sk) | ...
sock_put(sk) // FREE |
| bh_lock_sock(sk) // USE
The sock is deallocated by sock_put() in rose_release() and
then used by bh_lock_sock() in rose_heartbeat_expiry().
Although rose_destroy_socket() calls rose_stop_heartbeat(),
it could not stop the timer that is running.
The KASAN report triggered by POC is shown below:
BUG: KASAN: use-after-free in _raw_spin_lock+0x5a/0x110
Write of size 4 at addr ffff88800ae59098 by task swapper/3/0
...
Call Trace:
<IRQ>
dump_stack_lvl+0xbf/0xee
print_address_description+0x7b/0x440
print_report+0x101/0x230
? irq_work_single+0xbb/0x140
? _raw_spin_lock+0x5a/0x110
kasan_report+0xed/0x120
? _raw_spin_lock+0x5a/0x110
kasan_check_range+0x2bd/0x2e0
_raw_spin_lock+0x5a/0x110
rose_heartbeat_expiry+0x39/0x370
? rose_start_heartbeat+0xb0/0xb0
call_timer_fn+0x2d/0x1c0
? rose_start_heartbeat+0xb0/0xb0
expire_timers+0x1f3/0x320
__run_timers+0x3ff/0x4d0
run_timer_softirq+0x41/0x80
__do_softirq+0x233/0x544
irq_exit_rcu+0x41/0xa0
sysvec_apic_timer_interrupt+0x8c/0xb0
</IRQ>
<TASK>
asm_sysvec_apic_timer_interrupt+0x1b/0x20
RIP: 0010:default_idle+0xb/0x10
RSP: 0018:ffffc9000012fea0 EFLAGS: 00000202
RAX: 000000000000bcae RBX: ffff888006660f00 RCX: 000000000000bcae
RDX: 0000000000000001 RSI: ffffffff843a11c0 RDI: ffffffff843a1180
RBP: dffffc0000000000 R08: dffffc0000000000 R09: ffffed100da36d46
R10: dfffe9100da36d47 R11: ffffffff83cf0950 R12: 0000000000000000
R13: 1ffff11000ccc1e0 R14: ffffffff8542af28 R15: dffffc0000000000
...
Allocated by task 146:
__kasan_kmalloc+0xc4/0xf0
sk_prot_alloc+0xdd/0x1a0
sk_alloc+0x2d/0x4e0
rose_create+0x7b/0x330
__sock_create+0x2dd/0x640
__sys_socket+0xc7/0x270
__x64_sys_socket+0x71/0x80
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Freed by task 152:
kasan_set_track+0x4c/0x70
kasan_set_free_info+0x1f/0x40
____kasan_slab_free+0x124/0x190
kfree+0xd3/0x270
__sk_destruct+0x314/0x460
rose_release+0x2fa/0x3b0
sock_close+0xcb/0x230
__fput+0x2d9/0x650
task_work_run+0xd6/0x160
exit_to_user_mode_loop+0xc7/0xd0
exit_to_user_mode_prepare+0x4e/0x80
syscall_exit_to_user_mode+0x20/0x40
do_syscall_64+0x4f/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
This patch adds refcount of sock when we use functions
such as rose_start_heartbeat() and so on to start timer,
and decreases the refcount of sock when timer is finished
or deleted by functions such as rose_stop_heartbeat()
and so on. As a result, the UAF bugs could be mitigated.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Tested-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220629002640.5693-1-duoming@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch corrects packet receiving in ax88179_rx_fixup.
- problem observed:
ifconfig shows allways a lot of 'RX Errors' while packets
are received normally.
This occurs because ax88179_rx_fixup does not recognise properly
the usb urb received.
The packets are normally processed and at the end, the code exits
with 'return 0', generating RX Errors.
(pkt_cnt==-2 and ptk_hdr over field rx_hdr trying to identify
another packet there)
This is a usb urb received by "tcpdump -i usbmon2 -X" on a
little-endian CPU:
0x0000: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
^ packet 1 start (pkt_len = 0x05ec)
^^^^ IP alignment pseudo header
^ ethernet packet start
last byte ethernet packet v
padding (8-bytes aligned) vvvv vvvv
0x05e0: c92d d444 1420 8a69 83dd 272f e82b 9811
0x05f0: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
... ^ packet 2
0x0be0: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
...
0x1130: 9d41 9171 8a38 0ec5 eeee f8e3 3b19 87a0
...
0x1720: 8cfc 15ff 5e4c e85c eeee f8e3 3b19 87a0
...
0x1d10: ecfa 2a3a 19ab c78c eeee f8e3 3b19 87a0
...
0x2070: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
... ^ packet 7
0x2120: 7c88 4ca5 5c57 7dcc 0d34 7577 f778 7e0a
0x2130: f032 e093 7489 0740 3008 ec05 0000 0080
====1==== ====2====
hdr_off ^
pkt_len = 0x05ec ^^^^
AX_RXHDR_*=0x00830 ^^^^ ^
pkt_len = 0 ^^^^
AX_RXHDR_DROP_ERR=0x80000000 ^^^^ ^
0x2140: 3008 ec05 0000 0080 3008 5805 0000 0080
0x2150: 3008 ec05 0000 0080 3008 ec05 0000 0080
0x2160: 3008 5803 0000 0080 3008 c800 0000 0080
===11==== ===12==== ===13==== ===14====
0x2170: 0000 0000 0e00 3821
^^^^ ^^^^ rx_hdr
^^^^ pkt_cnt=14
^^^^ hdr_off=0x2138
^^^^ ^^^^ padding
The dump shows that pkt_cnt is the number of entrys in the
per-packet metadata. It is "2 * packet count".
Each packet have two entrys. The first have a valid
value (pkt_len and AX_RXHDR_*) and the second have a
dummy-header 0x80000000 (pkt_len=0 with AX_RXHDR_DROP_ERR).
Why exists dummy-header for each packet?!?
My guess is that this was done probably to align the
entry for each packet to 64-bits and maintain compatibility
with old firmware.
There is also a padding (0x00000000) before the rx_hdr to
align the end of rx_hdr to 64-bit.
Note that packets have a alignment of 64-bits (8-bytes).
This patch assumes that the dummy-header and the last
padding are optional. So it preserves semantics and
recognises the same valid packets as the current code.
This patch was made using only the dumpfile information and
tested with only one device:
0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
Fixes: 57bc3d3ae8 ("net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup")
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/d6970bb04bf67598af4d316eaeb1792040b18cfd.camel@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
HDMI 2.1 section 10.3.6 defines an HDMI Forum EDID Extension Override
Data Block, which may contain a different extension count than the base
block claims. Add support for reading more EDID data if available. The
extra blocks aren't parsed yet, though.
Hard-coding the EEODB parsing instead of using the iterators we have is
a bit of a bummer, but we have to be able to do this on a partially
allocated EDID while reading it.
v2:
- Check for CEA Data Block Collection size (Ville)
- Amend commit message and comment about hard-coded parsing
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/57b57a355d62eb91ad1e3cf555978576f2bd9fdd.1656494768.git.jani.nikula@intel.com
Add a new function drm_edid_connector_update() to replace the
combination of calls drm_connector_update_edid_property() and
drm_add_edid_modes(). Usually they are called in the drivers in this
order, however the former needs information from the latter.
Since the new drm_edid_read*() functions no longer call the connector
updates directly, and the read and update are separated, we'll need this
new function for the connector update.
This is all in drm_edid.c simply to keep struct drm_edid opaque.
v2:
- Share code with drm_connector_update_edid_property() (Ville)
- Add comment about override EDID handling
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/75aa3dbc8c9aa26ebbcdeacd98a466ef8d8827f4.1656494768.git.jani.nikula@intel.com
Add functions drm_edid_override_set() and drm_edid_override_reset() to
support "edid_override" connector debugfs, and to hide the details about
it in drm_edid.c. No functional changes at this time.
Also note in the connector.override_edid flag kernel-doc that this is
only supposed to be modified by the code doing debugfs EDID override
handling. Currently, it is still being modified by amdgpu in
create_eml_sink() and handle_edid_mgmt() for reasons unknown. This was
added in commit 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
and later moved to amdgpu_dm.c in commit e7b07ceef2 ("drm/amd/display:
Merge amdgpu_dm_types and amdgpu_dm").
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8f6b4001630cafac5f44aa5913429ac9979743d2.1656494768.git.jani.nikula@intel.com
If the clear_ids attribute is set to true, the EUI/GUID/UUID is cleared
for the passthru target. By default, loop targets will set clear_ids to
true.
This resolves an issue where a connect to a passthru target fails when
using a trtype of 'loop' because EUI/GUID/UUID is not unique.
Fixes: 2079f41ec6 ("nvme: check that EUI/GUID/UUID are globally unique")
Signed-off-by: Alan Adamson <alan.adamson@oracle.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
commit 0622cab034 ("bonding: fix 802.3ad aggregator reselection"),
resolve case, when there is several aggregation groups in the same bond.
bond_3ad_unbind_slave will invalidate (clear) aggregator when
__agg_active_ports return zero. So, ad_clear_agg can be executed even, when
num_of_ports!=0. Than bond_3ad_unbind_slave can be executed again for,
previously cleared aggregator. NOTE: at this time bond_3ad_unbind_slave
will not update slave ports list, because lag_ports==NULL. So, here we
got slave ports, pointing to freed aggregator memory.
Fix with checking actual number of ports in group (as was before
commit 0622cab034 ("bonding: fix 802.3ad aggregator reselection") ),
before ad_clear_agg().
The KASAN logs are as follows:
[ 767.617392] ==================================================================
[ 767.630776] BUG: KASAN: use-after-free in bond_3ad_state_machine_handler+0x13dc/0x1470
[ 767.638764] Read of size 2 at addr ffff00011ba9d430 by task kworker/u8:7/767
[ 767.647361] CPU: 3 PID: 767 Comm: kworker/u8:7 Tainted: G O 5.15.11 #15
[ 767.655329] Hardware name: DNI AmazonGo1 A7040 board (DT)
[ 767.660760] Workqueue: lacp_1 bond_3ad_state_machine_handler
[ 767.666468] Call trace:
[ 767.668930] dump_backtrace+0x0/0x2d0
[ 767.672625] show_stack+0x24/0x30
[ 767.675965] dump_stack_lvl+0x68/0x84
[ 767.679659] print_address_description.constprop.0+0x74/0x2b8
[ 767.685451] kasan_report+0x1f0/0x260
[ 767.689148] __asan_load2+0x94/0xd0
[ 767.692667] bond_3ad_state_machine_handler+0x13dc/0x1470
Fixes: 0622cab034 ("bonding: fix 802.3ad aggregator reselection")
Co-developed-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220629012914.361-1-yevhen.orlov@plvision.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of asix_ax88772a_link_change_notify() workaround, we run soft
reset which will automatically clear MII_ADVERTISE configuration. The
PHYlib framework do not know about changed configuration state of the
PHY, so we need use phy_init_hw() to reinit PHY configuration.
Fixes: dde2584692 ("net: usb/phy: asix: add support for ax88772A/C PHYs")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220628114349.3929928-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
