On i.MX8Plus there are two updates for micfil module.
One is that the output format is S32_LE, only the 24 more
significative bits have information, the other bits are always
zero. Add 'formats' variable in soc data to distinguish the
format on different platform.
Another is that the fifo depth is 32 entries.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1652087663-1908-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For the quality setting the quality setting register values are directly
exposed to the kcontrol and thus to userspace. This is unfortunate
because the register settings contains invalid bit combinations marked
as "N/A". For userspace it doesn't make much sense to be able to set
these just to see that the driver responds with "Please make sure you
select a valid quality." in the kernel log.
Work around this by adding get/set functions for the quality setting.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20220414162249.3934543-17-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The reference manual has this for calculating the micfil internal clock
divider:
MICFIL Clock rate
clkdiv = -----------------
8 * OSR * outrate
(with OSR == Oversampling Rate, outrate == output sample rate)
The driver first sets the MICFIL Clock rate to (outrate * 1024) and then
calculates back the clkdiv value from the above calculation.
Simplify this by using a fixed clkdiv value of 8 and set the MICFIL
Clock rate to (outrate * clkdiv * OSR * 8).
While at it drop disabling the clock before setting its rate. The MICFIL
module is disabled when the rate is changed and it is also resetted
before it is started again, so I doubt it's necessary to disable the
clock.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20220414162249.3934543-16-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Failed register accesses are really not expected in memory mapped
registers. When it fails then the register access itself is likely not
the reason, so no need to have extra error messages for each regmap
access. Just drop the error messages. This also fixes some places where
a return value is concatenated using 'ret |=' and then returned as
error value.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20220414162249.3934543-8-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no defer probe when adding platform component to
snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime()
snd_soc_register_card()
-> snd_soc_bind_card()
-> snd_soc_add_pcm_runtime()
-> adding cpu dai
-> adding codec dai
-> adding platform component.
So if the platform component is not ready at that time, then the
sound card still registered successfully, but platform component
is empty, the sound card can't be used.
As there is defer probe checking for cpu dai component, then register
platform component before cpu dai to avoid such issue.
Fixes: 47a70e6fc9 ("ASoC: Add MICFIL SoC Digital Audio Interface driver.")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1630665006-31437-4-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When there is power domain bind with ipg_clk clock,
The call flow:
devm_regmap_init_mmio_clk
- clk_prepare()
- clk_pm_runtime_get()
cause the power domain of clock always be enabled after
regmap_init(). which impact the power consumption.
So use devm_regmap_init_mmio instead of
devm_regmap_init_mmio_clk,but explicitly enable
clock when it is used.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Viorel Suman <viorel.suman@nxp.com>
Link: https://lore.kernel.org/r/1616579928-22428-7-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_set_drvdata is not needed when the set data comes from
snd_soc_dai_get_drvdata or dev_get_drvdata. The problem was fixed
usingthe following semantic patch: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,y,e;
@@
x = dev_get_drvdata(y->dev)
... when != x = e
- snd_soc_dai_set_drvdata(y,x);
@@
expression x,y,e;
@@
x = snd_soc_dai_get_drvdata(y)
... when != x = e
- snd_soc_dai_set_drvdata(y,x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20210213101907.1318496-5-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
sound/soc/fsl/fsl_micfil.c: In function 'get_clk_div':
sound/soc/fsl/fsl_micfil.c:154:6: warning: variable 'osr' set but not used [-Wunused-but-set-variable]
It is never used since introduction in
commit 47a70e6fc9 ("ASoC: Add MICFIL SoC Digital Audio Interface driver.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Digital Audio Interface driver that convers PDM bitstream to PCM
format.
Features:
- Fixed filtering characteristics for audio application.
- Full or partial set of channels operation with individual enable control.
- Programmable PDM clock generator.
- Programmable decimation rate.
- 16-bit signed output result.
- Overall stopband attenuation more than 80dB.
- Overall passband ripple less than 0.2dB.
Signed-off-by: Cosmin-Gabriel Samoila <cosmin.samoila@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
