Currently the tlv320aic31xx driver has regulator support but does not
enable the regulators during probe, deferring this until something causes
ASoC to make the card active. It does put the device into cache only mode
but only when the component level probe is called, however if interrupts
are in use the driver will access the regmap before then which if the
regulators are not powered on would cause I/O problems.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210707160234.16253-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
None of the TAS2505 outputs are stereo, do not pretend they are by
implementing them using SOC*DOUBLE* macros referencing the same
register twice, use SOC*SINGLE* instead. Fix volume ranges and mute
control for the codec according to datasheet.
Fixes: b4525b6196 ("ASoC: tlv320aic32x4: add support for TAS2505")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Claudius Heine <ch@denx.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210708091255.56502-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
Pull driver core changes from Greg KH:
"Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues"
* tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
docs: ABI: testing: sysfs-firmware-memmap: add some memmap types.
devres: Enable trace events
devres: No need to call remove_nodes() when there none present
devres: Use list_for_each_safe_from() in remove_nodes()
devres: Make locking straight forward in release_nodes()
kernfs: move revalidate to be near lookup
drivers/base: Constify static attribute_group structs
firmware_loader: remove unneeded 'comma' macro
devcoredump: remove contact information
driver core: Drop helper devm_platform_ioremap_resource_wc()
component: Rename 'dev' to 'parent'
component: Drop 'dev' argument to component_match_realloc()
device property: Don't check for NULL twice in the loops
driver core: auxiliary bus: Fix typo in the docs
drivers/base/node.c: make CACHE_ATTR define static DEVICE_ATTR_RO
debugfs: remove return value of debugfs_create_ulong()
debugfs: remove return value of debugfs_create_bool()
scsi: snic: debugfs: remove local storage of debugfs files
b43: don't save dentries for debugfs
b43legacy: don't save dentries for debugfs
...
Pull mfd updates from Lee Jones:
"Core Frameworks:
- Fix Software Node clean-up code
New Drivers:
- Add support for MediaTek MT6359 PMIC
- Add support for Qualcomm PM8008 PMIC
- Add support for Richtek RT4831
New Device Support:
- Add support for Audio CODECs to Rockchip RK817
- Add support for Alder Lake-M to Intel LPSS PCI
- Add support for Periph Device Charge to ChromeOS EC
New Functionality:
- Provide additional IRQs for wcd934x
- Add optional Reset functionality to lp87565
Fix-ups:
- Namespacing & visibility fixes to lp87565
- Differentiate between Power and Home key IRQs in mt6358
- Export I2C device tables in da9052-i2c, stmpe-i2c
- Adapt IRQ flags in max8907, rn5t61, max8907
- Make some functions/devices optional in axp20x, cros_ec_dev
- Explicitly include used header files in ioc3
- Remove superfluous lines in MAINTAINERS, sec-core, st,stm32-timers
- Resolve Kerneldoc issues in omap-usb-host, omap-usb-tll, si476x-cmd, si476x-i2c
- Convert arizona-core to a module
- Copyright changes in hi655x-pmic
- Drop support for board file initialisation in sec-core
- Trivial spelling, whitespace etc updates in lp87565, si476x-cmd,
mt6360-core, wm831x-core, twl-core, db8500-prcmu
- Simplify various implementations of wcd934x, mt6360-core, max8997,
max8998, da9052-i2c, da9062-core, sec-core,
- Device Tree binding changes in google,cros-ec,
richtek,rt4831-backlight, db8500-prcmu, qcom,pm8008, qcom,spmi-pmic
- Use provided APIs to simplify t7l66xb, as3722, da9055-core,
tps80031, 88pm800, 88pm805, asic3, sun6i-prcm, wm831x-core,
wm831x-otp, ucb1x00-assabet, timberdale, sm501, pcf50633-core,
kempld-core, janz-cmodio, intel_soc_pmic_bxtwc, ab8500-core
Bug Fixes:
- Fix unused variable warning in rk817_codec
- Fix regulator voltage configuration in rohm-bd71828
- Fix ongoing freeing of regmap_config 'name' issue in syscon
- Fix error handling path in da9063-i2c
- Fix Kconfig issues in MFD_MP2629
- Fix DMA mask warnings in motorola-cpcap"
* tag 'mfd-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (83 commits)
mfd: cros_ec: Add peripheral device charger
mfd: max8907: Remove IRQF_NO_AUTOEN flag
mfd: ab8500-core: Use DEVICE_ATTR_RO/RW macro
mfd: intel_soc_pmic_bxtwc: Use DEVICE_ATTR_ADMIN_RW macro
mfd: janz-cmodio: Use DEVICE_ATTR_RO macro
mfd: kempld-core: Use DEVICE_ATTR_RO macro
mfd: pcf50633: Use DEVICE_ATTR_ADMIN_RO macro
mfd: sm501: Use DEVICE_ATTR_RO macro
mfd: timberdale: Use DEVICE_ATTR_RO macro
mfd: ucb1x00-assabet: Use DEVICE_ATTR_RO macro
mfd: wm831x: Use DEVICE_ATTR_RO macro
mfd: wm831x: Use DEFINE_RES_IRQ_NAMED() and DEFINE_RES_IRQ() to simplify code
dt-bindings: mfd: stm32-timers: Remove #address/size cells from required properties
mfd: sun6i-prcm: Use DEFINE_RES_MEM() to simplify code
mfd: asic3: Use DEFINE_RES_MEM() and DEFINE_RES_IRQ() to simplify code
mfd: 88pm805: Use DEFINE_RES_IRQ_NAMED() to simplify code
mfd: 88pm800: Use DEFINE_RES_IRQ_NAMED() to simplify code
mfd: tps80031: Use DEFINE_RES_IRQ() to simplify code
mfd: da9055: Use DEFINE_RES_IRQ_NAMED() to simplify code
mfd: as3722: Use DEFINE_RES_IRQ_NAMED() to simplify code
...
When wm_coeff_tlv_get was updated it was accidentally switch to the _raw
version of the helper causing it to ignore the current DSP state it
should be checking. Switch the code back to the correct helper so that
users can't read the controls when they arn't available.
Fixes: 73ecf1a673 ("ASoC: wm_adsp: Correct cache handling of new kernel control API")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210626155941.12251-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
this is v2 from my patchset that add support for the TAS2505 to the tlv320aic32x4 driver.
kind regards,
Claudius
Changes from v1:
- clarified commit message of first patch, which add the type value to the struct
- removed unnecessary code to put and get speaker volume
- removed 'Gain' from 'HP Driver Playback Volume' control
- fixed rebase issues
Claudius Heine (3):
ASoC: tlv320aic32x4: add type to device private data struct
ASoC: tlv320aic32x4: add support for TAS2505
ASoC: tlv320aic32x4: dt-bindings: add TAS2505 to compatible
.../bindings/sound/tlv320aic32x4.txt | 1 +
sound/soc/codecs/tlv320aic32x4-i2c.c | 22 ++-
sound/soc/codecs/tlv320aic32x4-spi.c | 23 ++-
sound/soc/codecs/tlv320aic32x4.c | 139 +++++++++++++++++-
sound/soc/codecs/tlv320aic32x4.h | 10 ++
5 files changed, 186 insertions(+), 9 deletions(-)
base-commit: 70585216fe
--
2.32.0
While this driver can already handle different device variants, the
variant information cannot be used in the driver code and therefor
cannot have different code paths depending on the device variant.
This change adds a `type` value into the `aic32x4_priv` structure, that
contains a device variant identifier, which was set when the driver was
bound to the device.
Signed-off-by: Claudius Heine <ch@denx.de>
Link: https://lore.kernel.org/r/20210617085230.1851503-2-ch@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes below two uninitialized symbol warnings
warning:
sound/soc/codecs/wcd938x.c:2092 wcd938x_tx_swr_ctrl()
error: uninitialized symbol 'rate'
sound/soc/codecs/wcd938x.c:2189 wcd938x_tx_channel_config()
error: uninitialized symbol 'reg'.
First one my brining in check to already existing if condition and
second one by adding a default switch case to avoid any access to reg.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210621134502.19537-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In the initial driver we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error. While we
did not see this IO error on RT711-sdca-based platforms, the code pattern
is similar to the RT700 case where the IO error was noted, so the fix
is added for consistency.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
The code is slightly different from the other codecs since the
interrupt callback deals with the SDCA interrupts, leading to a much
larger section that's protected by the mutex. The SoundWire interrupt
scheme requires a read after clearing a status, it's not clear from
the specifications what would happen if SDCA interrupts are disabled
in the middle of the sequence, so the entire interrupt status
read/write is kept as is, even if in the end we discard the
information.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 7ad4d237e7 ('ASoC: rt711-sdca: Add RT711 SDCA vendor-specific driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the initial driver we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error. While we
did not see this IO error on RT5682-based platforms, the code pattern
is similar to the RT700 case where the IO error was noted, so the fix
is added for consistency.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
The Fixes tag points to a 5.10 commit, there's no need to propagate
this change to earlier upstream versions.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 4a55000722 ('ASoC: codecs: rt*.c: remove useless pointer cast')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In previous commits we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error. While we
did not see this IO error on RT711-based platforms, the code pattern
is similar to the RT700 case where the IO error was noted, so the fix
is added for consistency.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 501ef01339 ('ASoC: rt711: wait for the delayed work to finish when the system suspends')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In previous commits we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 5f2df2a458 ('ASoC: rt700: wait for the delayed work to finish when the system suspends')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason we ended up with cyclic dependency between snd_soc_wcd938x
and snd_soc_wcd938x_sdw modules.
Remove this cyclic dependency by handling them in respective modules.
Without this below error is reported during make modules_install
depmod: ERROR: Cycle detected: snd_soc_wcd938x -> snd_soc_wcd938x_sdw -> snd_soc_wcd938x
depmod: ERROR: Found 2 modules in dependency cycles!
Fixes: 0454422288 ("ASoC: codecs: wcd938x: add audio routing and Kconfig")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210615132829.23067-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset adds support for Qualcomm WCD938X codec.
Qualcomm WCD9380/WCD9385 Codec is a standalone Hi-Fi audio codec IC
connected over SoundWire. This device has two SoundWire devices, RX and
TX respectively supporting 4 x ADCs, ClassH, Ear, Aux PA, 2xHPH,
7 x TX diff inputs, 8 DMICs and MBHC.
Eventhough this device has two SoundWire devices, only tx device has
access to main codec Control/Status Registers!
For codec driver to be functional it would need both tx and rx Soundwire devices
to be up and this is taken care by using device component framework and device-links
are used to ensure proper pm dependencies. Ex tx does not enter suspend
before rx or codec is suspended.
This patchset along with other SoundWire patches on the list
have been tested on SM8250 MTP device.
Thanks,
srini
Changes since v8:
- moved Kconfig and Makefile changes to last patch as suggested by Mark
- removed array of enums and used static entries instead. Suggested by Mark
- return true if put succeeds, Suggested by Mark
- removed some unneeded semi-colons in switch
Srinivas Kandagatla (9):
ASoC: dt-bindings: wcd938x: add bindings for wcd938x
ASoC: codecs: wcd-clsh: add new version support
ASoC: codecs: wcd938x: add basic driver
ASoC: dt-bindings: wcd938x-sdw: add bindings for wcd938x-sdw
ASoC: codecs: wcd938x-sdw: add SoundWire driver
ASoC: codecs: wcd938x: add basic controls
ASoC: codecs: wcd938x: add playback dapm widgets
ASoC: codecs: wcd938x: add capture dapm widgets
ASoC: codecs: wcd938x: add audio routing and Kconfig
.../bindings/sound/qcom,wcd938x-sdw.yaml | 70 +
.../bindings/sound/qcom,wcd938x.yaml | 146 +
sound/soc/codecs/Kconfig | 14 +
sound/soc/codecs/Makefile | 4 +
sound/soc/codecs/wcd-clsh-v2.c | 348 +-
sound/soc/codecs/wcd-clsh-v2.h | 16 +
sound/soc/codecs/wcd938x-sdw.c | 315 ++
sound/soc/codecs/wcd938x.c | 3753 +++++++++++++++++
sound/soc/codecs/wcd938x.h | 720 ++++
9 files changed, 5376 insertions(+), 10 deletions(-)
create mode 100644 Documentation/devicetree/bindings/sound/qcom,wcd938x-sdw.yaml
create mode 100644 Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml
create mode 100644 sound/soc/codecs/wcd938x-sdw.c
create mode 100644 sound/soc/codecs/wcd938x.c
create mode 100644 sound/soc/codecs/wcd938x.h
--
2.21.0
Pull sound fixes from Takashi Iwai:
"A bit more commits than expected at this time, but likely it's the
last shot before the final.
Many of changes are device-specific fix-ups for various ASoC drivers,
while a few usual HD-audio quirks and a FireWire fix, as well as a
couple of ALSA / ASoC core fixes.
All look nice and small, and nothing to scare much"
* tag 'sound-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: Fix race of snd_seq_timer_open()
ALSA: hda/realtek: fix mute/micmute LEDs for HP ZBook Power G8
ALSA: hda/realtek: headphone and mic don't work on an Acer laptop
ASoC: qcom: lpass-cpu: Fix pop noise during audio capture begin
ALSA: firewire-lib: fix the context to call snd_pcm_stop_xrun()
ALSA: hda/realtek: fix mute/micmute LEDs for HP EliteBook 840 Aero G8
ALSA: hda/realtek: fix mute/micmute LEDs and speaker for HP EliteBook x360 1040 G8
ALSA: hda/realtek: fix mute/micmute LEDs and speaker for HP Elite Dragonfly G2
ASoC: rt5682: Fix the fast discharge for headset unplugging in soundwire mode
ASoC: tas2562: Fix TDM_CFG0_SAMPRATE values
ASoC: meson: gx-card: fix sound-dai dt schema
ASoC: AMD Renoir: Remove fix for DMI entry on Lenovo 2020 platforms
ASoC: AMD Renoir - add DMI entry for Lenovo 2020 AMD platforms
ASoC: SOF: reset enabled_cores state at suspend
ASoC: fsl-asoc-card: Set .owner attribute when registering card.
ASoC: topology: Fix spelling mistake "vesion" -> "version"
ASoC: rt5659: Fix the lost powers for the HDA header
ASoC: core: Fix Null-point-dereference in fmt_single_name()
The IEC958 status bit is usually set by the userspace after hw_params
has been called, so in order to use whatever is set by the userspace, we
need to implement the prepare hook. Let's add it to the hdmi_codec_ops,
and mandate that either prepare or hw_params is implemented.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210525132354.297468-6-maxime@cerno.tech
The IEC958 status bits can be exposed and modified by the userspace
through dedicated ALSA controls.
This patch implements those controls for the hdmi-codec driver. It
relies on a default value being setup at probe time that can later be
overridden by the control put.
The hw_params callback is then called with a buffer filled with the
proper bits for the current parameters being passed on so the underlying
driver can just reuse those bits as is.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210525132354.297468-5-maxime@cerno.tech
One of the fixes reverted as part of the UMN fallout was actually fine,
however rather than undoing the revert the process that handled all this
stuff resulted in a patch which attempted to add extra error checks
instead. Unfortunately this new change wasn't really based on a good
understanding of the subsystem APIs and bypassed the usual patch flow
without ensuring it was reviewed by people with subsystem knowledge and
was merged as a fix rather than during the merge window.
The effect of the new fix is to upgrade what were previously warnings on
static data in the code to hard errors on that data. If this actually
happens then it would break existing systems, if it doesn't happen then
the change has no effect so this was not a safe change to apply as a fix
to the release candidates. Since the new code has not been tested and
doesn't in practice improve error handling revert it instead, and also
drop the original revert since the original fix was fine. This takes
the driver back to what it was in -rc1.
Fixes: 5e70b8e22b ("ASoC: rt5645: add error checking to rt5645_probe function")
Fixes: 1e0ce84215 ("Revert "ASoC: rt5645: fix a NULL pointer dereference")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Phillip Potter <phil@philpotter.co.uk>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210608160713.21040-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
