Currently, DSA programs VLANs on shared (DSA and CPU) ports each time it
does so on user ports. This is good for basic functionality but has
several limitations:
- the VLAN group which must reach the CPU may be radically different
from the VLAN group that must be autonomously forwarded by the switch.
In other words, the admin may want to isolate noisy stations and avoid
traffic from them going to the control processor of the switch, where
it would just waste useless cycles. The bridge already supports
independent control of VLAN groups on bridge ports and on the bridge
itself, and when VLAN-aware, it will drop packets in software anyway
if their VID isn't added as a 'self' entry towards the bridge device.
- Replaying host FDB entries may depend, for some drivers like mv88e6xxx,
on replaying the host VLANs as well. The 2 VLAN groups are
approximately the same in most regular cases, but there are corner
cases when timing matters, and DSA's approximation of replicating
VLANs on shared ports simply does not work.
- If a user makes the bridge (implicitly the CPU port) join a VLAN by
accident, there is no way for the CPU port to isolate itself from that
noisy VLAN except by rebooting the system. This is because for each
VLAN added on a user port, DSA will add it on shared ports too, but
for each VLAN deletion on a user port, it will remain installed on
shared ports, since DSA has no good indication of whether the VLAN is
still in use or not.
Now that the bridge driver emits well-balanced SWITCHDEV_OBJ_ID_PORT_VLAN
addition and removal events, DSA has a simple and straightforward task
of separating the bridge port VLANs (these have an orig_dev which is a
DSA slave interface, or a LAG interface) from the host VLANs (these have
an orig_dev which is a bridge interface), and to keep a simple reference
count of each VID on each shared port.
Forwarding VLANs must be installed on the bridge ports and on all DSA
ports interconnecting them. We don't have a good view of the exact
topology, so we simply install forwarding VLANs on all DSA ports, which
is what has been done until now.
Host VLANs must be installed primarily on the dedicated CPU port of each
bridge port. More subtly, they must also be installed on upstream-facing
and downstream-facing DSA ports that are connecting the bridge ports and
the CPU. This ensures that the mv88e6xxx's problem (VID of host FDB
entry may be absent from VTU) is still addressed even if that switch is
in a cross-chip setup, and it has no local CPU port.
Therefore:
- user ports contain only bridge port (forwarding) VLANs, and no
refcounting is necessary
- DSA ports contain both forwarding and host VLANs. Refcounting is
necessary among these 2 types.
- CPU ports contain only host VLANs. Refcounting is also necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev_handle_port_obj_add() helper is good for replicating a
port object on the lower interfaces of @dev, if that object was emitted
on a bridge, or on a bridge port that is a LAG.
However, drivers that use this helper limit themselves to a box from
which they can no longer intercept port objects notified on neighbor
ports ("foreign interfaces").
One such driver is DSA, where software bridging with foreign interfaces
such as standalone NICs or Wi-Fi APs is an important use case. There, a
VLAN installed on a neighbor bridge port roughly corresponds to a
forwarding VLAN installed on the DSA switch's CPU port.
To support this use case while also making use of the benefits of the
switchdev_handle_* replication helper for port objects, introduce a new
variant of these functions that crawls through the neighbor ports of
@dev, in search of potentially compatible switchdev ports that are
interested in the event.
The strategy is identical to switchdev_handle_fdb_event_to_device():
if @dev wasn't a switchdev interface, then go one step upper, and
recursively call this function on the bridge that this port belongs to.
At the next recursion step, __switchdev_handle_port_obj_add() will
iterate through the bridge's lower interfaces. Among those, some will be
switchdev interfaces, and one will be the original @dev that we came
from. To prevent infinite recursion, we must suppress reentry into the
original @dev, and just call the @add_cb for the switchdev_interfaces.
It looks like this:
br0
/ | \
/ | \
/ | \
swp0 swp1 eth0
1. __switchdev_handle_port_obj_add(eth0)
-> check_cb(eth0) returns false
-> eth0 has no lower interfaces
-> eth0's bridge is br0
-> switchdev_lower_dev_find(br0, check_cb, foreign_dev_check_cb))
finds br0
2. __switchdev_handle_port_obj_add(br0)
-> check_cb(br0) returns false
-> netdev_for_each_lower_dev
-> check_cb(swp0) returns true, so we don't skip this interface
3. __switchdev_handle_port_obj_add(swp0)
-> check_cb(swp0) returns true, so we call add_cb(swp0)
(back to netdev_for_each_lower_dev from 2)
-> check_cb(swp1) returns true, so we don't skip this interface
4. __switchdev_handle_port_obj_add(swp1)
-> check_cb(swp1) returns true, so we call add_cb(swp1)
(back to netdev_for_each_lower_dev from 2)
-> check_cb(eth0) returns false, so we skip this interface to
avoid infinite recursion
Note: eth0 could have been a LAG, and we don't want to suppress the
recursion through its lowers if those exist, so when check_cb() returns
false, we still call switchdev_lower_dev_find() to estimate whether
there's anything worth a recursion beneath that LAG. Using check_cb()
and foreign_dev_check_cb(), switchdev_lower_dev_find() not only figures
out whether the lowers of the LAG are switchdev, but also whether they
actively offload the LAG or not (whether the LAG is "foreign" to the
switchdev interface or not).
The port_obj_info->orig_dev is preserved across recursive calls, so
switchdev drivers still know on which device was this notification
originally emitted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_switchdev_port_vlan_add() currently emits a SWITCHDEV_PORT_OBJ_ADD
event with a SWITCHDEV_OBJ_ID_PORT_VLAN for 2 distinct cases:
- a struct net_bridge_vlan got created
- an existing struct net_bridge_vlan was modified
This makes it impossible for switchdev drivers to properly balance
PORT_OBJ_ADD with PORT_OBJ_DEL events, so if we want to allow that to
happen, we must provide a way for drivers to distinguish between a
VLAN with changed flags and a new one.
Annotate struct switchdev_obj_port_vlan with a "bool changed" that
distinguishes the 2 cases above.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx is special among DSA drivers in that it requires the VTU to
contain the VID of the FDB entry it modifies in
mv88e6xxx_port_db_load_purge(), otherwise it will return -EOPNOTSUPP.
Sometimes due to races this is not always satisfied even if external
code does everything right (first deletes the FDB entries, then the
VLAN), because DSA commits to hardware FDB entries asynchronously since
commit c9eb3e0f87 ("net: dsa: Add support for learning FDB through
notification").
Therefore, the mv88e6xxx driver must close this race condition by
itself, by asking DSA to flush the switchdev workqueue of any FDB
deletions in progress, prior to exiting a VLAN.
Fixes: c9eb3e0f87 ("net: dsa: Add support for learning FDB through notification")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wireless-next patches for v5.18
First set of patches for v5.18, with both wireless and stack patches.
rtw89 now has AP mode support and wcn36xx has survey support. But
otherwise pretty normal.
Major changes:
ath11k
* add LDPC FEC type in 802.11 radiotap header
* enable RX PPDU stats in monitor co-exist mode
wcn36xx
* implement survey reporting
brcmfmac
* add CYW43570 PCIE device
rtw88
* rtw8821c: enable RFE 6 devices
rtw89
* AP mode support
mt76
* mt7916 support
* background radar detection support
This counter has never been visible, there is little point
trying to maintain it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we can control SMC handshake limitation through socket options,
which means that applications who need it must modify their code. It's
quite troublesome for many existing applications. This patch modifies
the global default value of SMC handshake limitation through netlink,
providing a way to put constraint on handshake without modifies any code
for applications.
Suggested-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having to acquire rtnl from netdev_run_todo() for every dismantled
device is not desirable when/if rtnl is under stress.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As depicted in the IEEE 802.15.4 specification, modulation/bands are
tight to a number of page/channels so we can for most of them derive the
durations automatically.
The two locations that must call this new helper to set the variou
symbol durations are:
- when manually requesting a channel change though the netlink interface
- at PHY creation, once the device driver has set the default
page/channel
If an information is missing, the symbol duration is not touched, a
debug message is eventually printed. This keeps the compatibility with
the unconverted drivers for which it was too complicated for me to find
their precise information. If they initially provided a symbol duration,
it would be kept. If they don't, the symbol duration value is left
untouched.
Once the symbol duration derived, the lifs and sifs durations are
updated as well.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220201180629.93410-4-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Tdsym is often given in the spec as pretty small numbers in microseconds
and hence was reflected in the code as symbol_duration and was stored as
a u8. Actually, for UWB PHYs, the symbol duration is given in
nanoseconds and are as precise as picoseconds. In order to handle better
these PHYs, change the type of symbol_duration to u32 and store this
value in nanoseconds.
All the users of this variable are updated in a mechanical way.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220201180629.93410-3-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2022-02-10
An update from ieee802154 for your *net-next* tree.
There is more ongoing in ieee802154 than usual. This will be the first pull
request for this cycle, but I expect one more. Depending on review and rework
times.
Pavel Skripkin ported the atusb driver over to the new USB api to avoid unint
problems as well as making use of the modern api without kmalloc() needs in he
driver.
Miquel Raynal landed some changes to ensure proper frame checksum checking with
hwsim, documenting our use of wake and stop_queue and eliding a magic value by
using the proper define.
David Girault documented the address struct used in ieee802154.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) Conntrack sets on CHECKSUM_UNNECESSARY for UDP packet with no checksum,
from Kevin Mitchell.
2) skb->priority support for nfqueue, from Nicolas Dichtel.
3) Remove conntrack extension register API, from Florian Westphal.
4) Move nat destroy hook to nf_nat_hook instead, to remove
nf_ct_ext_destroy(), also from Florian.
5) Wrap pptp conntrack NAT hooks into single structure, from Florian Westphal.
6) Support for tcp option set to noop for nf_tables, also from Florian.
7) Do not run x_tables comment match from packet path in nf_tables,
from Florian Westphal.
8) Replace spinlock by cmpxchg() loop to update missed ct event,
from Florian Westphal.
9) Wrap cttimeout hooks into single structure, from Florian.
10) Add fast nft_cmp expression for up to 16-bytes.
11) Use cb->ctx to store context in ctnetlink dump, instead of using
cb->args[], from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: ctnetlink: use dump structure instead of raw args
nfqueue: enable to set skb->priority
netfilter: nft_cmp: optimize comparison for 16-bytes
netfilter: cttimeout: use option structure
netfilter: ecache: don't use nf_conn spinlock
netfilter: nft_compat: suppress comment match
netfilter: exthdr: add support for tcp option removal
netfilter: conntrack: pptp: use single option structure
netfilter: conntrack: remove extension register api
netfilter: conntrack: handle ->destroy hook via nat_ops instead
netfilter: conntrack: move extension sizes into core
netfilter: conntrack: make all extensions 8-byte alignned
netfilter: nfqueue: enable to get skb->priority
netfilter: conntrack: mark UDP zero checksum as CHECKSUM_UNNECESSARY
====================
Link: https://lore.kernel.org/r/20220209133616.165104-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-02-09
We've added 126 non-merge commits during the last 16 day(s) which contain
a total of 201 files changed, 4049 insertions(+), 2215 deletions(-).
The main changes are:
1) Add custom BPF allocator for JITs that pack multiple programs into a huge
page to reduce iTLB pressure, from Song Liu.
2) Add __user tagging support in vmlinux BTF and utilize it from BPF
verifier when generating loads, from Yonghong Song.
3) Add per-socket fast path check guarding from cgroup/BPF overhead when
used by only some sockets, from Pavel Begunkov.
4) Continued libbpf deprecation work of APIs/features and removal of their
usage from samples, selftests, libbpf & bpftool, from Andrii Nakryiko
and various others.
5) Improve BPF instruction set documentation by adding byte swap
instructions and cleaning up load/store section, from Christoph Hellwig.
6) Switch BPF preload infra to light skeleton and remove libbpf dependency
from it, from Alexei Starovoitov.
7) Fix architecture-agnostic macros in libbpf for accessing syscall
arguments from BPF progs for non-x86 architectures,
from Ilya Leoshkevich.
8) Rework port members in struct bpf_sk_lookup and struct bpf_sock to be
of 16-bit field with anonymous zero padding, from Jakub Sitnicki.
9) Add new bpf_copy_from_user_task() helper to read memory from a different
task than current. Add ability to create sleepable BPF iterator progs,
from Kenny Yu.
10) Implement XSK batching for ice's zero-copy driver used by AF_XDP and
utilize TX batching API from XSK buffer pool, from Maciej Fijalkowski.
11) Generate temporary netns names for BPF selftests to avoid naming
collisions, from Hangbin Liu.
12) Implement bpf_core_types_are_compat() with limited recursion for
in-kernel usage, from Matteo Croce.
13) Simplify pahole version detection and finally enable CONFIG_DEBUG_INFO_DWARF5
to be selected with CONFIG_DEBUG_INFO_BTF, from Nathan Chancellor.
14) Misc minor fixes to libbpf and selftests from various folks.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (126 commits)
selftests/bpf: Cover 4-byte load from remote_port in bpf_sk_lookup
bpf: Make remote_port field in struct bpf_sk_lookup 16-bit wide
libbpf: Fix compilation warning due to mismatched printf format
selftests/bpf: Test BPF_KPROBE_SYSCALL macro
libbpf: Add BPF_KPROBE_SYSCALL macro
libbpf: Fix accessing the first syscall argument on s390
libbpf: Fix accessing the first syscall argument on arm64
libbpf: Allow overriding PT_REGS_PARM1{_CORE}_SYSCALL
selftests/bpf: Skip test_bpf_syscall_macro's syscall_arg1 on arm64 and s390
libbpf: Fix accessing syscall arguments on riscv
libbpf: Fix riscv register names
libbpf: Fix accessing syscall arguments on powerpc
selftests/bpf: Use PT_REGS_SYSCALL_REGS in bpf_syscall_macro
libbpf: Add PT_REGS_SYSCALL_REGS macro
selftests/bpf: Fix an endianness issue in bpf_syscall_macro test
bpf: Fix bpf_prog_pack build HPAGE_PMD_SIZE
bpf: Fix leftover header->pages in sparc and powerpc code.
libbpf: Fix signedness bug in btf_dump_array_data()
selftests/bpf: Do not export subtest as standalone test
bpf, x86_64: Fail gracefully on bpf_jit_binary_pack_finalize failures
...
====================
Link: https://lore.kernel.org/r/20220209210050.8425-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change adds a couple of new ioctls for mctp sockets:
SIOCMCTPALLOCTAG and SIOCMCTPDROPTAG. These ioctls provide facilities
for explicit allocation / release of tags, overriding the automatic
allocate-on-send/release-on-reply and timeout behaviours. This allows
userspace more control over messages that may not fit a simple
request/response model.
In order to indicate a pre-allocated tag to the sendmsg() syscall, we
introduce a new flag to the struct sockaddr_mctp.smctp_tag value:
MCTP_TAG_PREALLOC.
Additional changes from Jeremy Kerr <jk@codeconstruct.com.au>.
Contains a fix that was:
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we have a couple of paths that check that an EID matches, or
the match value is MCTP_ADDR_ANY.
Rather than open coding this, add a little helper.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When uncloning an skb dst and its associated metadata, a new
dst+metadata is allocated and later replaces the old one in the skb.
This is helpful to have a non-shared dst+metadata attached to a specific
skb.
The issue is the uncloned dst+metadata is initialized with a refcount of
1, which is increased to 2 before attaching it to the skb. When
tun_dst_unclone returns, the dst+metadata is only referenced from a
single place (the skb) while its refcount is 2. Its refcount will never
drop to 0 (when the skb is consumed), leading to a memory leak.
Fix this by removing the call to dst_hold in tun_dst_unclone, as the
dst+metadata refcount is already 1.
Fixes: fc4099f172 ("openvswitch: Fix egress tunnel info.")
Cc: Pravin B Shelar <pshelar@ovn.org>
Reported-by: Vlad Buslov <vladbu@nvidia.com>
Tested-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When uncloning an skb dst and its associated metadata a new dst+metadata
is allocated and the tunnel information from the old metadata is copied
over there.
The issue is the tunnel metadata has references to cached dst, which are
copied along the way. When a dst+metadata refcount drops to 0 the
metadata is freed including the cached dst entries. As they are also
referenced in the initial dst+metadata, this ends up in UaFs.
In practice the above did not happen because of another issue, the
dst+metadata was never freed because its refcount never dropped to 0
(this will be fixed in a subsequent patch).
Fix this by initializing the dst cache after copying the tunnel
information from the old metadata to also unshare the dst cache.
Fixes: d71785ffc7 ("net: add dst_cache to ovs vxlan lwtunnel")
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: Vlad Buslov <vladbu@nvidia.com>
Tested-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow up to 16-byte comparisons with a new cmp fast version. Use two
64-bit words and calculate the mask representing the bits to be
compared. Make sure the comparison is 64-bit aligned and avoid
out-of-bound memory access on registers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of two exported functions, export a single option structure.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
For updating eache missed value we can use cmpxchg.
This also avoids need to disable BH.
kernel robot reported build failure on v1 because not all arches support
cmpxchg for u16, so extend this to u32.
This doesn't increase struct size, existing padding is used.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Next step for using per netns inet6_addr_lst
is to have per netns work item to ultimately
call addrconf_verify_rtnl() and addrconf_verify()
with a new 'struct net*' argument.
Everything is still using the global inet6_addr_lst[] table.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a per netns hash table and a dedicated spinlock,
first step to get rid of the global inet6_addr_lst[] one.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new dscp_t type to replace the fc_tos field of fib_config, to
ensure IPv4 routes aren't influenced by ECN bits when configured with
non-zero rtm_tos.
Before this patch, IPv4 routes specifying an rtm_tos with some of the
ECN bits set were accepted. However they wouldn't work (never match) as
IPv4 normally clears the ECN bits with IPTOS_RT_MASK before doing a FIB
lookup (although a few buggy code paths don't).
After this patch, IPv4 routes specifying an rtm_tos with any ECN bit
set is rejected.
Note: IPv6 routes ignore rtm_tos altogether, any rtm_tos is accepted,
but treated as if it were 0.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define a dscp_t type and its appropriate helpers that ensure ECN bits
are not taken into account when handling DSCP.
Use this new type to replace the tclass field of struct fib6_rule, so
that fib6-rules don't get influenced by ECN bits anymore.
Before this patch, fib6-rules didn't make any distinction between the
DSCP and ECN bits. Therefore, rules specifying a DSCP (tos or dsfield
options in iproute2) stopped working as soon a packets had at least one
of its ECN bits set (as a work around one could create four rules for
each DSCP value to match, one for each possible ECN value).
After this patch fib6-rules only compare the DSCP bits. ECN doesn't
influence the result anymore. Also, fib6-rules now must have the ECN
bits cleared or they will be rejected.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While testing a patch that will follow later
("net: add netns refcount tracker to struct nsproxy")
I found that devtmpfs_init() was called before init_net
was initialized.
This is a bug, because devtmpfs_setup() calls
ksys_unshare(CLONE_NEWNS);
This has the effect of increasing init_net refcount,
which will be later overwritten to 1, as part of setup_net(&init_net)
We had too many prior patches [1] trying to work around the root cause.
Really, make sure init_net is in BSS section, and that net_ns_init()
is called earlier at boot time.
Note that another patch ("vfs: add netns refcount tracker
to struct fs_context") also will need net_ns_init() being called
before vfs_caches_init()
As a bonus, this patch saves around 4KB in .data section.
[1]
f8c46cb390 ("netns: do not call pernet ops for not yet set up init_net namespace")
b5082df801 ("net: Initialise init_net.count to 1")
734b65417b ("net: Statically initialize init_net.dev_base_head")
v2: fixed a build error reported by kernel build bots (CONFIG_NET=n)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While inspecting some perf report, I noticed that the compiler
emits suboptimal code for the napi CB initialization, fetching
and storing multiple times the memory for flags bitfield.
This is with gcc 10.3.1, but I observed the same with older compiler
versions.
We can help the compiler to do a nicer work clearing several
fields at once using an u32 alias. The generated code is quite
smaller, with the same number of conditional.
Before:
objdump -t net/core/gro.o | grep " F .text"
0000000000000bb0 l F .text 0000000000000357 dev_gro_receive
After:
0000000000000bb0 l F .text 000000000000033c dev_gro_receive
v1 -> v2:
- use struct_group (Alexander and Alex)
RFC -> v1:
- use __struct_group to delimit the zeroed area (Alexander)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tc skb extension is used to send miss info from
tc to ovs datapath module, and driver to tc. For the tc to ovs
miss it is currently always allocated even if it will not
be used by ovs datapath (as it depends on a requested feature).
Export the static key which is used by openvswitch module to
guard this code path as well, so it will be skipped if ovs
datapath doesn't need it. Enable this code path once
ovs datapath needs it.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These no longer register/unregister a meaningful structure so remove it.
Cc: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The nat module already exposes a few functions to the conntrack core.
Move the nat extension destroy hook to it.
After this, no conntrack extension needs a destroy hook.
'struct nf_ct_ext_type' and the register/unregister api can be removed
in a followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
No need to specify this in the registration modules, we already
collect all sizes for build-time checks on the maximum combined size.
After this change, all extensions except nat have no meaningful content
in their nf_ct_ext_type struct definition.
Next patch handles nat, this will then allow to remove the dynamic
register api completely.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All extensions except one need 8 byte alignment, so just make that the
default.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The previous commit d01ffb9eee ("ax25: add refcount in ax25_dev
to avoid UAF bugs") introduces refcount into ax25_dev, but there
are reference leak paths in ax25_ctl_ioctl(), ax25_fwd_ioctl(),
ax25_rt_add(), ax25_rt_del() and ax25_rt_opt().
This patch uses ax25_dev_put() and adjusts the position of
ax25_addr_ax25dev() to fix reference cout leaks of ax25_dev.
Fixes: d01ffb9eee ("ax25: add refcount in ax25_dev to avoid UAF bugs")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220203150811.42256-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Given that standalone ports are now configured to bypass the ATU and
forward all frames towards the upstream port, extend the ATU bypass to
multichip systems.
Load VID 0 (standalone) into the VTU with the policy bit set. Since
VID 4095 (bridged) is already loaded, we now know that all VIDs in use
are always available in all VTUs. Therefore, we can safely enable
802.1Q on DSA ports.
Setting the DSA ports' VTU policy to TRAP means that all incoming
frames on VID 0 will be classified as MGMT - as a result, the ATU is
bypassed on all subsequent switches.
With this isolation in place, we are able to support configurations
that are simultaneously very quirky and very useful. Quirky because it
involves looping cables between local switchports like in this
example:
CPU
| .------.
.---0---. | .----0----.
| sw0 | | | sw1 |
'-1-2-3-' | '-1-2-3-4-'
$ @ '---' $ @ % %
We have three physically looped pairs ($, @, and %).
This is very useful because it allows us to run the kernel's
kselftests for the bridge on mv88e6xxx hardware.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear MapDA on standalone ports to bypass any ATU lookup that might
point the packet in the wrong direction. This means that all packets
are flooded using the PVT config. So make sure that standalone ports
are only allowed to communicate with the local upstream port.
Here is a scenario in which this is needed:
CPU
| .----.
.---0---. | .--0--.
| sw0 | | | sw1 |
'-1-2-3-' | '-1-2-'
'---'
- sw0p1 and sw1p1 are bridged
- sw0p2 and sw1p2 are in standalone mode
- Learning must be enabled on sw0p3 in order for hardware forwarding
to work properly between bridged ports
1. A packet with SA :aa comes in on sw1p2
1a. Egresses sw1p0
1b. Ingresses sw0p3, ATU adds an entry for :aa towards port 3
1c. Egresses sw0p0
2. A packet with DA :aa comes in on sw0p2
2a. If an ATU lookup is done at this point, the packet will be
incorrectly forwarded towards sw0p3. With this change in place,
the ATU is bypassed and the packet is forwarded in accordance
with the PVT, which only contains the CPU port.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to permit a driver to perform "fragmenting" of the
page from within the driver instead of the current model which requires
pre-partitioning the page. The main motivation behind this is to support
use cases where the page will be split up by the driver after DMA instead
of before.
With this change it becomes possible to start using page pool to replace
some of the existing use cases where multiple references were being used
for a single page, but the number needed was unknown as the size could be
dynamic.
For example, with this code it would be possible to do something like
the following to handle allocation:
page = page_pool_alloc_pages();
if (!page)
return NULL;
page_pool_fragment_page(page, DRIVER_PAGECNT_BIAS_MAX);
rx_buf->page = page;
rx_buf->pagecnt_bias = DRIVER_PAGECNT_BIAS_MAX;
Then we would process a received buffer by handling it with:
rx_buf->pagecnt_bias--;
Once the page has been fully consumed we could then flush the remaining
instances with:
if (page_pool_defrag_page(page, rx_buf->pagecnt_bias))
continue;
page_pool_put_defragged_page(pool, page -1, !!budget);
The general idea is that we want to have the ability to allocate a page
with excess fragment count and then trim off the unneeded fragments.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzkaller was able to trigger a deadlock for NTF_MANAGED entries [0]:
kworker/0:16/14617 is trying to acquire lock:
ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: ___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652
[...]
but task is already holding lock:
ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: neigh_managed_work+0x35/0x250 net/core/neighbour.c:1572
The neighbor entry turned to NUD_FAILED state, where __neigh_event_send()
triggered an immediate probe as per commit cd28ca0a3d ("neigh: reduce
arp latency") via neigh_probe() given table lock was held.
One option to fix this situation is to defer the neigh_probe() back to
the neigh_timer_handler() similarly as pre cd28ca0a3d. For the case
of NTF_MANAGED, this deferral is acceptable given this only happens on
actual failure state and regular / expected state is NUD_VALID with the
entry already present.
The fix adds a parameter to __neigh_event_send() in order to communicate
whether immediate probe is allowed or disallowed. Existing call-sites
of neigh_event_send() default as-is to immediate probe. However, the
neigh_managed_work() disables it via use of neigh_event_send_probe().
[0] <TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_deadlock_bug kernel/locking/lockdep.c:2956 [inline]
check_deadlock kernel/locking/lockdep.c:2999 [inline]
validate_chain kernel/locking/lockdep.c:3788 [inline]
__lock_acquire.cold+0x149/0x3ab kernel/locking/lockdep.c:5027
lock_acquire kernel/locking/lockdep.c:5639 [inline]
lock_acquire+0x1ab/0x510 kernel/locking/lockdep.c:5604
__raw_write_lock_bh include/linux/rwlock_api_smp.h:202 [inline]
_raw_write_lock_bh+0x2f/0x40 kernel/locking/spinlock.c:334
___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652
ip6_finish_output2+0x1070/0x14f0 net/ipv6/ip6_output.c:123
__ip6_finish_output net/ipv6/ip6_output.c:191 [inline]
__ip6_finish_output+0x61e/0xe90 net/ipv6/ip6_output.c:170
ip6_finish_output+0x32/0x200 net/ipv6/ip6_output.c:201
NF_HOOK_COND include/linux/netfilter.h:296 [inline]
ip6_output+0x1e4/0x530 net/ipv6/ip6_output.c:224
dst_output include/net/dst.h:451 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
ndisc_send_skb+0xa99/0x17f0 net/ipv6/ndisc.c:508
ndisc_send_ns+0x3a9/0x840 net/ipv6/ndisc.c:650
ndisc_solicit+0x2cd/0x4f0 net/ipv6/ndisc.c:742
neigh_probe+0xc2/0x110 net/core/neighbour.c:1040
__neigh_event_send+0x37d/0x1570 net/core/neighbour.c:1201
neigh_event_send include/net/neighbour.h:470 [inline]
neigh_managed_work+0x162/0x250 net/core/neighbour.c:1574
process_one_work+0x9ac/0x1650 kernel/workqueue.c:2307
worker_thread+0x657/0x1110 kernel/workqueue.c:2454
kthread+0x2e9/0x3a0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
</TASK>
Fixes: 7482e3841d ("net, neigh: Add NTF_MANAGED flag for managed neighbor entries")
Reported-by: syzbot+5239d0e1778a500d477a@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Tested-by: syzbot+5239d0e1778a500d477a@syzkaller.appspotmail.com
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220201193942.5055-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When setting RTO through BPF program, some SYN ACK packets were unaffected
and continued to use TCP_TIMEOUT_INIT constant. This patch adds timeout
option to struct request_sock. Option is initialized with TCP_TIMEOUT_INIT
and is reassigned through BPF using tcp_timeout_init call. SYN ACK
retransmits now use newly added timeout option.
Signed-off-by: Akhmat Karakotov <hmukos@yandex-team.ru>
Acked-by: Martin KaFai Lau <kafai@fb.com>
v2:
- Add timeout option to struct request_sock. Do not call
tcp_timeout_init on every syn ack retransmit.
v3:
- Use unsigned long for min. Bound tcp_timeout_init to TCP_RTO_MAX.
v4:
- Refactor duplicate code by adding reqsk_timeout function.
Signed-off-by: David S. Miller <davem@davemloft.net>
