Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
Pull ARM SoC cleanups from Olof Johansson:
"Cleanups for 3.16. Among these are:
- a bunch of misc cleanups for Broadcom platforms, mostly
housekeeping
- enabling Common Clock Framework on the older s3c24xx Samsung
chipsets
- cleanup of the Versatile Express system controller code, moving it
to syscon
- power management cleanups for OMAP platforms
plus a handful of other cleanups across the place"
* tag 'cleanup-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
ARM: kconfig: allow PCI support to be selected with ARCH_MULTIPLATFORM
clk: samsung: fix build error
ARM: vexpress: refine dependencies for new code
clk: samsung: clk-s3c2410-dlck: do not use PNAME macro as it declares __initdata
cpufreq: exynos: Fix the compile error
ARM: S3C24XX: move debug-macro.S into the common space
ARM: S3C24XX: use generic DEBUG_UART_PHY/_VIRT in debug macro
ARM: S3C24XX: trim down debug uart handling
ARM: compressed/head.S: remove s3c24xx special case
ARM: EXYNOS: Remove unnecessary inclusion of cpu.h
ARM: EXYNOS: Migrate Exynos specific macros from plat to mach
ARM: EXYNOS: Remove exynos_subsys registration
ARM: EXYNOS: Remove duplicate lines in Makefile
ARM: EXYNOS: use v7_exit_coherency_flush macro for cache disabling
ARM: OMAP4: PRCM: remove references to cm-regbits-44xx.h from PRCM core files
ARM: OMAP3/4: PRM: add support of late_init call to prm_ll_ops
ARM: OMAP3/OMAP4: PRM: add prm_features flags and add IO wakeup under it
ARM: OMAP3/4: PRM: provide io chain reconfig function through irq setup
ARM: OMAP2+: PRM: remove unnecessary cpu_is_XXX calls from prm_init / exit
ARM: OMAP2+: PRCM: cleanup some header includes
...
Merge "Samsung 3rd clock updates for 3.16" from Kukjin Kim:
- add clock for new exynos5410 SoC
* tag 'samsung-clk-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clk: exynos5410: register clocks using common clock framework
Signed-off-by: Olof Johansson <olof@lixom.net>
The EXYNOS5410 clocks are statically listed and registered
using the Samsung specific common clock helper functions.
Signed-off-by: Tarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: Vyacheslav Tyrtov <v.tyrtov@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Merge "Samsung 2nd clock updates for 3.16" from Kukjin Kim:
- Add missing sysmmu clocks for DISP and ISP blocks for exynos5250
* tag 'samsung-clk-2' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Samsung clock updates for 3.16" from Kukjin Kim:
In this time, it is having dependency with arch/arm/ for 3.16,
I pulled them into samsung tree from Tomasz under agreement from Mike.
- Pull for_3.16/exynos5260 from Tomasz Figa:
"This pull request contains patches preparing Samsung Common Clock Framework
helpers to support Exynos5260 by adding support for multiple clock providers
and then adding clock driver for Exynos5260."
- Pull for_3.16/clk_fixes_non_critical from Tomasz Figa:
"This pull requests contains a number of non-critical fixes for Samsung clock
framework and drivers, including:
1) a series of fixes for Exynos5420 to correct clock definitions and make the
driver closer to the documentation,
2) several missing clocks and clock IDs added to Exynos4, Exynos5250 and
Exynos5420 drivers,
3) fix for incorrect initialization of clock table with NULL,
4) compiler warning fix."
- Pull for_3.16/clk_cleanup from Tomasz Figa:
"This pull requests contains minor clean-up related to Samsung clock
support, including:
1) move Kconfig entries of Samsung clock drivers to drivers/clk,
2) compile drivers/clk/samsung conditionally when COMMON_CLK_SAMSUNG is
selected,
3) remove obsolete Kconfig lines after moving s3c24xx to CCF."
- Pull for_3.16/exynos3250 from Tomasz Figa:
"This small pull request contains a patch adding clock driver for Exynos3250,
which depends on previous pull requests in this series."
- add dt bindings for exynos3250 clock
- add exynos5800 specific clocks in current exynos5420 clock
Note that this branch is based on s3c24xx ccf branch
* tag 'samsung-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (59 commits)
clk: exynos5420: Add 5800 specific clocks
dt-bindings: add documentation for Exynos3250 clock controller
ARM: S3C24XX: fix merge conflict
clk: samsung: exynos3250: Add clocks using common clock framework
drivers: clk: use COMMON_CLK_SAMSUNG for Samsung clock support
ARM: S3C24XX: move S3C24XX clock Kconfig options to Samsung clock Kconfig file
ARM: select COMMON_CLK_SAMSUNG for ARCH_EXYNOS and ARCH_S3C64XX
clk: samsung: add new Kconfig for Samsung common clock option
ARM: S3C24XX: Remove omitted Kconfig selects and conditionals
clk: samsung: exynos5420: add more registers to restore list
clk: samsung: exynos5420: add misc clocks
clk: samsung: exynos5420: update clocks for MAU Block
clk: samsung: exynos5420: fix register offset for sclk_bpll
clk: samsung: exynos5420: correct sysmmu-mfc parent clocks
clk: samsung: exynos5420: update clocks for FSYS and FSYS2 blocks
clk: samsung: exynos5420: update clocks for WCORE block
clk: samsung: exynos5420: update clocks for PERIS and GEN blocks
clk: samsung: exynos5420: update clocks for PERIC block
clk: samsung: exynos5420: update clocks for DISP1 block
clk: samsung: exynos5420: update clocks for G2D and G3D blocks
...
Signed-off-by: Olof Johansson <olof@lixom.net>
A new PLL (gpll4) is added on msm8974 PRO devices to support a
faster sdc1 clock rate. Add support for this and the two new sdcc
cal clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Merge "ARM: berlin: DT changes for v3.16" from Sebastian Hesselbart:
Quite a lot changes but it looks like DT approach is really paying off.
BG2Q joins Berlin SoC family with corresponding development board, DW
gpio nodes for all SoCs. Most notably, we have settled clock bindings
to allow us to continue on drivers requiring clocks and pinctrl bindings.
Last but not least, BG2Q gained SDHCI support and is able to properly
boot into userspace.
* tag 'berlin-dt-3.16' of https://github.com/shesselba/linux-berlin:
ARM: dts: berlin: enable SD card reader and eMMC for the BG2Q DMP
ARM: dts: berlin: add the SDHCI nodes for the BG2Q
ARM: dts: berlin: add the pinctrl node and muxing setup for uarts
dt-binding: ARM: add pinctrl binding docs for Marvell Berlin2 SoCs
ARM: dts: berlin: convert BG2Q to DT clock nodes
ARM: dts: berlin: convert BG2 to DT clock nodes
ARM: dts: berlin: convert BG2CD to DT clock nodes
clk: berlin: add binding include for Berlin SoC clock ids
dt-binding: ARM: add clock binding docs for Marvell Berlin2 SoCs
ARM: dts: berlin: add the BG2CD GPIO nodes
ARM: dts: berlin: add the BG2 GPIO nodes
ARM: dts: berlin: add the BG2Q GPIO nodes
ARM: dts: berlin: add scu and chipctrl device nodes for BG2/BG2Q
ARM: dts: berlin: add the Marvell BG2-Q DMP device tree
ARM: dts: berlin: add the Marvell Armada 1500 pro
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: STi: DT changes for v3.16, v3" from Maxime Coquelin:
Please consider these STi DT updates for v3.16.
This 3rd version takes into account Olof's comments on the v2:
- Fix upper-cases in labels and node names
- Sort compatibles order from specific to generic
- Sort dts entries in Makefile
It also adds support for the B2020 revision E board for STiH416 SoC.
Note that two reset patches are part of this pull request, in order to avoid
compilation breakage.
Adding these two patches in this pull request has been accepted by Philipp Zabel.
* tag 'sti-dt-for-v3.16-1' of git://git.stlinux.com/devel/kernel/linux-sti: (23 commits)
ARM: sti: stih41x: Provide a proper header for this DTSI file
ARM: sti: stih416: Enable board LED support for B2020 RevE
ARM: sti: stih416: Add support for B2020 RevE
ARM: STi: DT: STiH41x Add clk_ignore_unused to bootargs
ARM: STi: DT: STiH415: 415 DT Entry for clockgen A9
ARM: STi: DT: STiH415: Remove unused CLK_S_GMAC0_PHY & CLK_S_ETH1_PHY fixed clocks
ARM: STi: DT: STiH415: Remove unused CLK_S_ICN_REG_0 fixed clock
ARM: STi: DT: STiH415: 415 DT Entry for clockgen A0/1/10/11/12
ARM: STi: DT: STiH416: 416 DT Entry for clockgen A9/DDR/GPU
ARM: STi: DT: STiH416: 416 DT Entry for clockgen B/C/D/E/F
ARM: STi: DT: STiH416: Remove unused CLK_S_GMAC0_PHY & CLK_S_ETH1_PHY fixed clocks
ARM: STi: DT: STiH416: Remove unused CLK_S_ICN_REG_0 fixed clock
ARM: STi: DT: STiH416: 416 DT Entry for clockgen A0/1/10/11/12
ARM: STi: DT: STiH41x: Rename CLK_SYSIN into clk_sysin
ARM: STi: DT: add keyscan for stih41x-b2000
ARM: STi: DT: add keyscan for stih416
ARM: STi: DT: add keyscan for stih415
driver: reset: sti: add keyscan for stih416
driver: reset: sti: add keyscan for stih415
ARM: dts: STiH407: Add B2120 board support
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Patches from Anders Berg applied individually:
Here is version 4 of platform support for AXM5516 SoC.
The clk driver is now applied to clk-next. The rest should be ready for
arm-soc. Haven't got any response from the power/reset maintainers... I hope
this driver can be taken via arm-soc as well.
The AXM55xx family consists of devices that may contain up to 16 ARM Cortex-A15
cores (in a 4x4 cluster configuration). The cores within each cluster share an
L2 cache, and the clusters are connected to each other via a CCN-504 cache
coherent interconnect.
This machine requires CONFIG_ARM_LPAE enabled as all peripherals are located
above 4GB in the memory map.
* axxia/soc:
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
ARM: dts: Device tree for AXM55xx.
ARM: Add platform support for LSI AXM55xx SoC
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The AXM55xx family consists of devices that may contain up to 16 ARM Cortex-A15
cores (in a 4x4 cluster configuration). The cores within each cluster share an
L2 cache, and the clusters are connected to each other via a CCN-504 cache
coherent interconnect.
This machine requires CONFIG_ARM_LPAE enabled as all peripherals are located
above 4GB in the memory map.
Signed-off-by: Anders Berg <anders.berg@lsi.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently the Tegra1x4 clock init code hard-codes the mux setting
for xusb_hs_src and treats it as a fixed-factor clock. It is,
however, a mux which can be parented by either xusb_ss_src/2 or
pll_u_60M. Add the fixed-factor clock xusb_ss_div2 and put an
entry in periph_clks[] for the xusb_hs_src mux.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Merge "Samsung S3C24XX updates for 3.16" from Kukjin Kim:
Samsung S3C24XX to use the common clock framework
- S3C2412, S3C2413, S3C2416 and S3C2443 to use CCF
- S3C2410, S3C2440, S3C2442 to use CCF
- Remove legacy samsung clock from mach-s3c24xx/
- Some of them are missed from previous pull-request
- Clock related sutff got ack from Mike and Tomasz
- Created the last commit due to missing changes
during re-sorting because this branch is provided
as a base to samsung clk tree.
* tag 's3c24xx-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (23 commits)
ARM: S3C24XX: fix merge conflict
ARM: S3C24XX: remove SAMSUNG_CLOCK remnants after ccf conversion
ARM: S3C24XX: remove legacy clock code
ARM: S3C24XX: convert s3c2410 to common clock framework
ARM: S3C24XX: convert s3c2440 and s3c2442 to common clock framework
ARM: S3C24XX: add platform code for conversion to the common clock framework
clk: samsung: add clock controller driver for s3c2410, s3c2440 and s3c2442
dt-bindings: add documentation for s3c2410 clock controller
ARM: S3C24XX: enable usage of common dclk if common clock framework is enabled
clk: samsung: add clock driver for external clock outputs
ARM: S3C24XX: cpufreq-utils: don't write raw values to MPLLCON when using ccf
ARM: S3C24XX: convert s3c2412 to common clock framework
clk: samsung: add clock controller driver for s3c2412
dt-bindings: add documentation for s3c2412 clock controller
clk: samsung: add plls used by the early s3c24xx cpus
ARM: S3C24XX: only store clock registers when old clock code is active
ARM: S3C24XX: Convert s3c2416 and s3c2443 to common clock framework
ARM: dts: add clock data for s3c2416
ARM: S3C24XX: prevent conflicts between ccf and non-ccf s3c24xx-socs
clk: samsung: add clock-driver for s3c2416, s3c2443 and s3c2450
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: soc changes for 3.16" from Shawn Guo:
i.MX SoC changes for 3.16:
- A few cleanups on mx21ads board file, which should make the later
conversion to DT a little bit easier.
- Add some missing clocks and drop unused clk lookups for i.MX1 and
i.MX27 clock drivers
- Add initial i.MX SoloX (imx6sx) SoC support
- Remove mx51_babbage and mach-cpuimx51sd board files, as the
equivalent DT support is ready for the boards
- Clean up device tree timer initialization a little bit
- Add missing i2c4 clock for i.MX6 DualLite/Solo
- Add missing CKO clock i.MX25
- Add shared gate clock support for i.MX specific clk_gate2
- Add low-level debug support for SoC VF610
- Some random code cleanups and defconfig updates
* tag 'imx-soc-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (33 commits)
ARM: mx25: Add CLKO support
ARM: i.MX1 clk: Remove clk_register_clkdev() for unused clocks
ARM: i.MX1 clk: Add missing clocks
ARM: imx: add basic imx6sx SoC support
ARM: imx: add clock driver for imx6sx
ARM: imx: add low-level debug support for imx6sx
ARM: mx51: Remove mach-cpuimx51sd board file
ARM: i.MX: Setup IRQ handler from IRQ driver
ARM: i.MX27 pca100: remove deprecated IRQF_DISABLED
ARM: imx/mxs defconfigs: add MTD_SPI_NOR (new dependency for M25P80)
ARM: i.MX: Fix eMMa PrP resource size
ARM: imx_v4_v5_defconfig: drop CONFIG_COMMON_CLK_DEBUG option
ARM: i.MX27 clk: Remove clk_register_clkdev() for unused clocks
ARM: i.MX27 clk: Add missing clocks for MSHC and RTIC
ARM: imx6q: add the missing esai_ahb clock
ARM: imx: add shared gate clock support
ARM: imx: lock is always valid for clk_gate2
ARM: imx: define struct clk_gate2 on our own
ARM: i.MX: Remove #ifdef CONFIG_OF
ARM: imx_v6_v7_defconfig: enable option CONFIG_LOCALVERSION_AUTO
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Renesas ARM Based r7s72100 SoC CCF Updates for v3.16" from Simon Horman:
r7s72100 (RZ/A1H) SoC and its Genmai board
* Add and use CCF support
* Initislise SCIF, I2C and SPI via DT
* tag 'renesas-r7s72100-ccf-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r7s72100: use workaround for non DT-clocks
ARM: shmobile: Add forward declaration of struct clk to silence warning
ARM: shmobile: r7s72100: remove SPI DT clocks from legacy clock support
ARM: shmobile: r7s72100: add spi clocks to dtsi
ARM: shmobile: r7s72100: remove I2C DT clocks from legacy clock support
ARM: shmobile: r7s72100: add i2c clocks to dtsi
ARM: shmobile: r7s72100: genmai: platform scif devices only for legacy support
ARM: shmobile: r7s72100: genmai: add uart alias and activate scif2 as console
ARM: shmobile: r7s72100: add scif nodes to dtsi
ARM: shmobile: r7s72100: genmai: populate nodes for external clocks
ARM: shmobile: r7s72100: add essential clock nodes to dtsi
ARM: shmobile: r7s72100: document MSTP clock support
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Second Round of Renesas ARM Based SoC Clock Updates for v3.16" from
Simon Horman:
r8a7791 (R-Car M2) SoC
* Correct SYS-DMAC clock defines
r8a7740 (R-Mobile A1) SoC
* Correct name of DT Ethernet clock
* tag 'renesas-clock2-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: Correct SYS-DMAC clock defines
ARM: shmobile: r8a7740: Correct name of DT Ethernet clock
Signed-off-by: Olof Johansson <olof@lixom.net>
Exynos5800 clock structure is mostly similar to 5420 with only
a small delta changes. So the 5420 clock file is re-used for
5800 also. The common clocks for both are seggreagated and few
clocks which are different for both are separately initialized.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes some parent-child relationships according
to the latest datasheet and adds more clocks related to
PERIS and GEN blocks.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch includes,
1] renaming of the HSI2C clocks
2] renaming of spi clocks according to the datasheet
3] fixes for child-parent relationships
4] adding of more clocks related to PERIC block
5] use GATE_IP_* offsets instead of GATE_BUS_*
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch corrects some child-parent clock relationships,
and updates the clocks according to the latest datasheet.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds missing clocks of G2D block. It also removes
the aclkg3d alias from G3D block clocks.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds the missing GSCL and MSCL block clocks
and corrects some wrong parent-child relationships.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Adds IDs for the clocks needed by the ARM Mali GPU
in exynos5420.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds the required clocks for ARM Mali IP
in Exynos5250.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
[t.figa: Changed clock ID to avoid conflict with CLK_SSS]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Exynos4210 and Exynos4x12 SoCs have the PL330 MDMA IP block clock
defined exactly in same way in documentation. Using different
names for these clocks is a bit misleading. Since there is no users
of CLK_MDMA2 in existing dts files this patch drops CLK_MDMA2 and
replaces it with CLK_MDMA in the driver. This ensures PL330 MDMA
has correct clock assigned on Exynos4x12 SoCs.
Suggested-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds gating clock for SSS(Security SubSystem)
module on Exynos5250/5420.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
[t.figa: Fixed sort order and group name.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Add macros which are used as Clock IDs in DT and clock file.
It also adds the documentation for the exynos5260 clocks.
Signed-off-by: Rahul Sharma <Rahul.Sharma@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
R-Car M2 has two MSTP bits for SYS-DMAC, not one.
Also bring the naming in sync with the documentation.
This issue was introduced in v3.14, in commit
4d8864c9e9 ("ARM: shmobile: r8a7791: Add
clock index macros for DT sources").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This driver can handle the clock controllers of the socs mentioned above,
as they share a common clock tree with only small differences.
The clock structure is built according to the manuals of the included
SoCs and might include changes in comparison to the previous clock
structure.
As pll-rate-tables only the 12mhz variants are currently included.
The original code was wrongly checking for 169mhz xti values [a 0 to much
at the end], so the original 16mhz pll table would have never been
included and its values are so obscure that I have no possibility to
at least check their sane-ness. When using the formula from the manual
the resulting frequency is near the table value but still slightly off.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
