This patch adds support for the Brainboxes US-159, US-235 and US-320
USB-to-Serial devices.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Allow setting configfs params p_hs_bint/c_hs_bint to 0. If they are set
to 0, determine the largest bInterval (4 to 1) for which the required
bandwidth of the max samplerate fits the max allowed packet size. If the
required bandwidth exceeds max bandwidth for single-packet mode
(ep->mc=1), keep bInterval at 1.
The FS speed is left at fixed bInterval=1.
If for any speed the required bandwidth exceeds the max bandwidth
corresponding to the selected/determined bInterval, print a warning.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20220127114331.41367-4-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The support the external role switch a variety of situations were
addressed, but the transition from USB_ROLE_HOST to USB_ROLE_NONE
leaves the host up which can cause some error messages when
switching from host to none, to gadget, to none, and then back
to host again.
xhci-hcd ee000000.usb: Abort failed to stop command ring: -110
xhci-hcd ee000000.usb: xHCI host controller not responding, assume dead
xhci-hcd ee000000.usb: HC died; cleaning up
usb 4-1: device not accepting address 6, error -108
usb usb4-port1: couldn't allocate usb_device
After this happens it will not act as a host again.
Fix this by releasing the host mode when transitioning to USB_ROLE_NONE.
Fixes: 0604160d8c ("usb: gadget: udc: renesas_usb3: Enhance role switch support")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20220128223603.2362621-1-aford173@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under dummy_hcd, every available endpoint is *either* IN or OUT capable.
But with some real hardware, there are endpoints that support both IN and
OUT. In particular, the PLX 2380 has four available endpoints that each
support both IN and OUT.
raw-gadget currently gets confused and thinks that any endpoint that is
usable as an IN endpoint can never be used as an OUT endpoint.
Fix it by looking at the direction in the configured endpoint descriptor
instead of looking at the hardware capabilities.
With this change, I can use the PLX 2380 with raw-gadget.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Cc: stable <stable@vger.kernel.org>
Tested-by: Andrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20220126205214.2149936-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Programmable lab power supplies made by GW Instek, such as the
GPP-2323, have a USB port exposing a serial port to control the device.
Stringing the supplied Windows driver, references to the ch341 chip are
found. Binding the existing ch341 driver to the VID/PID of the GPP-2323
("GW Instek USB2.0-Serial" as per the USB product name) works out of the
box, communication and control is now possible.
This patch should work with any GPP series power supply due to
similarities in the product line.
Signed-off-by: Stephan Brunner <s.brunner@stephan-brunner.net>
Link: https://lore.kernel.org/r/4a47b864-0816-6f6a-efee-aa20e74bcdc6@stephan-brunner.net
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Consider a case where ffs_func_eps_disable is called from
ffs_func_disable as part of composition switch and at the
same time ffs_epfile_release get called from userspace.
ffs_epfile_release will free up the read buffer and call
ffs_data_closed which in turn destroys ffs->epfiles and
mark it as NULL. While this was happening the driver has
already initialized the local epfile in ffs_func_eps_disable
which is now freed and waiting to acquire the spinlock. Once
spinlock is acquired the driver proceeds with the stale value
of epfile and tries to free the already freed read buffer
causing use-after-free.
Following is the illustration of the race:
CPU1 CPU2
ffs_func_eps_disable
epfiles (local copy)
ffs_epfile_release
ffs_data_closed
if (last file closed)
ffs_data_reset
ffs_data_clear
ffs_epfiles_destroy
spin_lock
dereference epfiles
Fix this races by taking epfiles local copy & assigning it under
spinlock and if epfiles(local) is null then update it in ffs->epfiles
then finally destroy it.
Extending the scope further from the race, protecting the ep related
structures, and concurrent accesses.
Fixes: a9e6f83c2d ("usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable")
Co-developed-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Pratham Pratap <quic_ppratap@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/1643256595-10797-1-git-send-email-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When USB cable gets disconnected, the undergoing playback/capture
stalls, without any notification to u_audio about the change.
Experiments with a dwc2 gadget revealed that Suspend interrupt is
thrown at cable disconnection, which the gadget framework translates to
calling suspend callback of a function, if it is defined.
Add the suspend callback to f_uac2 function, calling
corresponding method of u_audio in order to stop the respective PCM
streams and to notify subscribed clients at cable disconnection.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20220121155308.48794-10-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Playback/Capture ctl currently reports rate value set by USB
control selector UAC2_CS_CONTROL_SAM_FREQ (fixed for UAC1). When the
stops playback/capture, the reported value does not change. The gadget
side has no information whether the host has started/stopped
capture/playback.
This patch sets the value reported by the respective rate ctl to zero
when the host side has stopped playback/capture. Also, it calls
snd_ctl_notify when start/stop occurs, so that a subscribed client can
act appropriately.
Tests have confirmed that USB hosts change UAC2_CS_CONTROL_SAM_FREQ
before switching altsetting to activate playback/capture, resulting in
correct order (params->c/p_srate is set to requested rate before
u_audio_start_capture/playback is called).
The gadget rate notifications are used by user-space audio gadget
controller gaudio_ctl https://github.com/pavhofman/gaudio_ctl.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20220121155308.48794-8-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A list of sampling rates can be specified via configfs. All enabled
sampling rates are sent to the USB host on request. When the host
selects a sampling rate the internal active rate is updated.
Config strings with single value stay compatible with the previous version.
Multiple samplerates passed as configuration arrays to g_audio module
when built for f_uac1.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20220121155308.48794-7-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A list of sampling rates can be specified via configfs. All enabled
sampling rates are sent to the USB host on request. When the host
selects a sampling rate, the internal active rate (stored in
struct f_uac2) is updated.
The gadget no longer supports only one frequency. Therefore USB strings
corresponding to the clock sources are renamed from specific Hz value to
general names Input clock/Output clock.
Config strings with single value stay compatible with the previous
version.
Multiple samplerates passed as configuration arrays to g_audio module
when built for f_uac2.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20220121155308.48794-6-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_hcd_pci_probe() searches for an I/O BAR using a combination of
PCI_STD_NUM_BARS (to control loop iteration) and PCI_ROM_RESOURCE (to check
whether the loop exits without finding anything).
Use PCI_STD_NUM_BARS consistently.
No functional change since PCI_STD_NUM_BARS == PCI_ROM_RESOURCE, but this
removes a dependency on that relationship and makes the code read better.
Fixes: c9c13ba428 ("PCI: Add PCI_STD_NUM_BARS for the number of standard BARs")
Cc: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20220121183330.1141702-1-helgaas@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unplugging USB device may cause an incorrect warm reset loop and the
port can no longer be used:
[ 143.039019] xhci_hcd 0000:00:14.0: Port change event, 2-3, id 19, portsc: 0x4202c0
[ 143.039025] xhci_hcd 0000:00:14.0: handle_port_status: starting usb2 port polling.
[ 143.039051] hub 2-0:1.0: state 7 ports 10 chg 0000 evt 0008
[ 143.039058] xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x4202c0, return 0x4102c0
[ 143.039092] xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x4002c0
[ 143.039096] usb usb2-port3: link state change
[ 143.039099] xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
[ 143.039101] usb usb2-port3: do warm reset
[ 143.096736] xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0
[ 143.096751] usb usb2-port3: not warm reset yet, waiting 50ms
[ 143.131500] xhci_hcd 0000:00:14.0: Can't queue urb, port error, link inactive
[ 143.138260] xhci_hcd 0000:00:14.0: Port change event, 2-3, id 19, portsc: 0x2802a0
[ 143.138263] xhci_hcd 0000:00:14.0: handle_port_status: starting usb2 port polling.
[ 143.160756] xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2802a0, return 0x3002a0
[ 143.160798] usb usb2-port3: not warm reset yet, waiting 200ms
The port status is PP=1, CCS=0, PED=0, PLS=Inactive, which is Error
state per "USB3 Root Hub Port State Machine". It's reasonable to perform
warm reset several times, but if the port is still not enabled after
many attempts, consider it's gone and treat it as disconnected.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220120070518.1643873-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some UDCs may return an error during pullup disable as part of the
unbind path for a USB configuration. This will lead to a scenario
where the disable() callback is skipped, whereas the unbind() still
occurs. If this happens, the u_serial driver will continue to fail
subsequent binds, due to an already existing entry in the ports array.
Ensure that gserial_disconnect() is called during the f_serial unbind,
so the ports entry is properly cleared.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220111064850.24311-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling dwc2_hsotg_ep_disable on ep0 (in/out) will lead to the following
logs before returning -EINVAL:
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
To avoid these two logs while suspending, start disabling the endpoint
from the index 1, as done in dwc2_hsotg_udc_stop:
/* all endpoints should be shutdown */
for (ep = 1; ep < hsotg->num_of_eps; ep++) {
if (hsotg->eps_in[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_in[ep]->ep);
if (hsotg->eps_out[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_out[ep]->ep);
}
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207130101.270314-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
