Clean up the line-status handling by dropping redundant initialisations
and returning early on errors.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
ScanLogic SL11R-IDE with firmware older than 2.6c (the latest one) has
broken tag handling, preventing the device from working at all:
usb 1-1: new full-speed USB device number 2 using uhci_hcd
usb 1-1: New USB device found, idVendor=04ce, idProduct=0002, bcdDevice= 2.60
usb 1-1: New USB device strings: Mfr=1, Product=1, SerialNumber=0
usb 1-1: Product: USB Device
usb 1-1: Manufacturer: USB Device
usb-storage 1-1:1.0: USB Mass Storage device detected
scsi host2: usb-storage 1-1:1.0
usbcore: registered new interface driver usb-storage
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
Add US_FL_BULK_IGNORE_TAG to fix it. Also update my e-mail address.
2.6c is the only firmware that claims Linux compatibility.
The firmware can be upgraded using ezotgdbg utility:
https://github.com/asciilifeform/ezotgdbg
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210913210106.12717-1-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race present where the DWC3 runtime resume runs in parallel
to the UDC unbind sequence. This will eventually lead to a possible
scenario where we are enabling the run/stop bit, without a valid
composition defined.
Thread#1 (handling UDC unbind):
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
-->dwc3_gadget_pullup(0)
--> continue UDC unbind sequence
-->Thread#2 is running in parallel here
Thread#2 (handing next cable connect)
__dwc3_set_mode()
-->pm_runtime_get_sync()
-->dwc3_gadget_resume()
-->dwc->gadget_driver is NOT NULL yet
-->dwc3_gadget_run_stop(1)
--> _dwc3gadget_start()
...
Fix this by tracking the pullup disable routine, and avoiding resuming
of the DWC3 gadget. Once the UDC is re-binded, that will trigger the
pullup enable routine, which would handle enabling the DWC3 gadget.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20210917021852.2037-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wrappers usb_control_msg_send/recv eliminate the need of manually
allocating DMA buffers for USB messages. They also treat short reads as
an error. Hence use the wrappers and remove DMA allocations.
Note that short reads are now logged as -EREMOTEIO instead of the amount
of data read.
Signed-off-by: Himadri Pandya <himadrispandya@gmail.com>
Link: https://lore.kernel.org/r/20210801203122.3515-7-himadrispandya@gmail.com
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
usb_control_msg_recv() nicely wraps usb_control_msg() and removes the
compulsion of using DMA buffers for USB messages. It also includes proper
error check for possible short read. So use the wrapper where
appropriate and remove DMA buffers from the callers.
Signed-off-by: Himadri Pandya <himadrispandya@gmail.com>
Link: https://lore.kernel.org/r/20210801203122.3515-5-himadrispandya@gmail.com
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The new wrapper functions usb_control_msg_send/recv accept stack
variables for USB message buffers and eliminate the need of manually
allocating temporary DMA buffers. The read wrapper also treats short
reads as errors. Hence use the wrappers instead of using
usb_control_msg() directly.
Note that the conversion of f81534a_ctrl_set_register() adds an extra an
extra allocation and memcpy for every retry. Since this function is
called rarely and retries are hopefully rare, the overhead should be
acceptable.
Also note that short reads are now logged as -EREMOTEIO instead of
indicating the amount of data read.
Signed-off-by: Himadri Pandya <himadrispandya@gmail.com>
Link: https://lore.kernel.org/r/20210801203122.3515-4-himadrispandya@gmail.com
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
User space can keep a tty open indefinitely and that should not prevent
a hung up port and its USB device from being runtime suspended.
Fix this by incrementing the PM usage counter when the port it activated
and decrementing the counter when the port is shutdown rather than when
the tty is installed and the last reference is dropped, respectively.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the core error labels by consistently naming them after what
they do rather than after from where they are jumped to.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
0xac24 device ID is already defined and used via
BANDB_DEVICE_ID_USO9ML2_4. Remove the duplicate from the list.
Fixes: 27f1281d5f ("USB: serial: Extra device/vendor ID for mos7840 driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
The USBDEVFS_CONTROL and USBDEVFS_BULK ioctls invoke
usb_start_wait_urb(), which contains an uninterruptible wait with a
user-specified timeout value. If timeout value is very large and the
device being accessed does not respond in a reasonable amount of time,
the kernel will complain about "Task X blocked for more than N
seconds", as found in testing by syzbot:
INFO: task syz-executor.0:8700 blocked for more than 143 seconds.
Not tainted 5.14.0-rc7-syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz-executor.0 state:D stack:23192 pid: 8700 ppid: 8455 flags:0x00004004
Call Trace:
context_switch kernel/sched/core.c:4681 [inline]
__schedule+0xc07/0x11f0 kernel/sched/core.c:5938
schedule+0x14b/0x210 kernel/sched/core.c:6017
schedule_timeout+0x98/0x2f0 kernel/time/timer.c:1857
do_wait_for_common+0x2da/0x480 kernel/sched/completion.c:85
__wait_for_common kernel/sched/completion.c:106 [inline]
wait_for_common kernel/sched/completion.c:117 [inline]
wait_for_completion_timeout+0x46/0x60 kernel/sched/completion.c:157
usb_start_wait_urb+0x167/0x550 drivers/usb/core/message.c:63
do_proc_bulk+0x978/0x1080 drivers/usb/core/devio.c:1236
proc_bulk drivers/usb/core/devio.c:1273 [inline]
usbdev_do_ioctl drivers/usb/core/devio.c:2547 [inline]
usbdev_ioctl+0x3441/0x6b10 drivers/usb/core/devio.c:2713
...
To fix this problem, this patch replaces usbfs's calls to
usb_control_msg() and usb_bulk_msg() with special-purpose code that
does essentially the same thing (as recommended in the comment for
usb_start_wait_urb()), except that it always uses a killable wait and
it uses GFP_KERNEL rather than GFP_NOIO.
Reported-and-tested-by: syzbot+ada0f7d3d9fd2016d927@syzkaller.appspotmail.com
Suggested-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210903175312.GA468440@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Isochronous endpoints, the SS companion descriptor's
wBytesPerInterval field is required to reserve bus time in order
to transmit the required payload during the service interval.
If left at 0, the UAC2 function is unable to transact data on its
playback or capture endpoints in SuperSpeed mode.
Since f_uac2 currently does not support any bursting this value can
be exactly equal to the calculated wMaxPacketSize.
Tested with Windows 10 as a host.
Fixes: f8cb3d556b ("usb: f_uac2: adds support for SS and SSP")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210909174811.12534-3-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The f_uac2 function fails to enumerate when connected in SuperSpeed
due to the feedback endpoint missing the companion descriptor.
Add a new ss_epin_fback_desc_comp descriptor and append it behind the
ss_epin_fback_desc both in the static definition of the ss_audio_desc
structure as well as its dynamic construction in setup_headers().
Fixes: 24f779dac8 ("usb: gadget: f_uac2/u_audio: add feedback endpoint support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210909174811.12534-2-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According USB spec each ISOC transaction should be performed in a
designated for that transaction interval. On bus errors or delays
in operating system scheduling of client software can result in no
packet being transferred for a (micro)frame. An error indication
should be returned as status to the client software in such a case.
Current implementation in case of missed/dropped interval send same
data in next possible interval instead of reporting missed isoc.
This fix complete requests with -ENODATA if interval elapsed.
HSOTG core in BDMA and Slave modes haven't HW support for
(micro)frames tracking, this is why SW should care about tracking
of (micro)frames. Because of that method and consider operating
system scheduling delays, added few additional checking's of elapsed
target (micro)frame:
1. Immediately before enabling EP to start transfer.
2. With any transfer completion interrupt.
3. With incomplete isoc in/out interrupt.
4. With EP disabled interrupt because of incomplete transfer.
5. With OUT token received while EP disabled interrupt (for OUT
transfers).
6. With NAK replied to IN token interrupt (for IN transfers).
As part of ISOC flow, additionally fixed 'current' and 'target' frame
calculation functions. In HS mode SOF limits provided by DSTS register
is 0x3fff, but in non HS mode this limit is 0x7ff.
Tested by internal tool which also using for dwc3 testing.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/95d1423adf4b0f68187c9894820c4b7e964a3f7f.1631175721.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After we start to do core soft reset while usb role switch,
the phy init is invoked at every switch to device mode, but
its counter part de-init is missing, this causes the actual
phy init can not be done when we really want to re-init phy
like system resume, because the counter maintained by phy
core is not 0. considering phy init is actually redundant for
role switch, so move out the phy init from core soft reset to
dwc3 core init where is the only place required.
Fixes: f88359e158 ("usb: dwc3: core: Do core softreset when switch mode")
Cc: <stable@vger.kernel.org>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Tested-by: John Stultz <john.stultz@linaro.org> #HiKey960
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1631068099-13559-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f3de5d857b.
That commit broke USB on all routers that have USB always powered on and
don't require toggling any GPIO. It's a majority of devices actually.
The original code worked and seemed safe: vcc GPIO is optional and
bcma_hci_platform_power_gpio() takes care of checking the pointer before
using it.
This revert fixes:
[ 10.801127] bcma_hcd: probe of bcma0:11 failed with error -2
Fixes: f3de5d857b ("USB: bcma: Add a check for devm_gpiod_get")
Cc: stable <stable@vger.kernel.org>
Cc: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20210831065419.18371-1-zajec5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use platform_register_drivers() and platform_unregister_drivers() to
register and unregister ehci platform drivers. This simplifies the code
and prevents the following build errors seen with sparc:allmodconfig.
drivers/usb/host/ehci-hcd.c:1301: error:
"PLATFORM_DRIVER" redefined
drivers/usb/host/ehci-sh.c:173:31: error:
'ehci_hcd_sh_driver' defined but not used
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210907123002.3951446-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For DEV_VER_V3 version there exist race condition between clearing
ep_sts.EP_STS_TRBERR and setting ep_cmd.EP_CMD_DRDY bit.
Setting EP_CMD_DRDY will be ignored by controller when
EP_STS_TRBERR is set. So, between these two instructions we have
a small time gap in which the EP_STSS_TRBERR can be set. In such case
the transfer will not start after setting doorbell.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org> # 5.12.x
Tested-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20210907062619.34622-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This loop is supposed to loop until if reads something other than
CS_IDST or until it times out after 30,000 attempts. But because of
the || vs && bug, it will never time out and instead it will loop a
minimum of 30,000 times.
This bug is quite old but the code is only used in USB_DEVICE_TEST_MODE
so it probably doesn't affect regular usage.
Fixes: 96fe53ef54 ("usb: gadget: r8a66597-udc: add support for TEST_MODE")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20210906094221.GA10957@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable master is being masked with ~MST_R_BITS however this
masked value is never used, the following updates to master are
assignments. I suspect the original intention was to mask out the
MST_R_BITS and then bit-wise or in the appropriate read bits rather
than perform an assignment. Fix this by using the |= operator rather
than a straight assignment.
Note that this code is pre-git history, so I can't find a sha for
it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210910163131.94796-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set reference clock period when it differs from dwc3 default hardware
set.
We could calculate clock period based on reference clock frequency. But
this information is not always available. This is the case of PCI bus
attached USB host. For that reason we use a custom property.
Tested (USB2 only) on IPQ6010 SoC based board with 24 MHz reference
clock while hardware default is 19.2 MHz.
[ baruch: rewrite commit message; drop GFLADJ code; remove 'quirk-' from
property name; mention tested hardware ]
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Balaji Prakash J <bjagadee@codeaurora.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Nacked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/9f399bdf1ff752e31ab7497e3d5ce19bbb3ff247.1630389452.git.baruch@tkos.co.il
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull more USB updates from Greg KH:
"Here are some straggler USB-serial changes for 5.15-rc1.
These were not included in the first pull request as they came in
"late" from Johan and I had missed them in my pull request earlier
this week.
Nothing big in here, just some USB to serial driver updates and fixes.
All of these were in linux-next before I pulled them into my tree, and
have been in linux-next all this week from my tree with no reported
problems"
* tag 'usb-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: pl2303: fix GL type detection
USB: serial: replace symbolic permissions by octal permissions
USB: serial: cp210x: determine fw version for CP2105 and CP2108
USB: serial: cp210x: clean up type detection
USB: serial: cp210x: clean up set-chars request
USB: serial: cp210x: clean up control-request timeout
USB: serial: cp210x: fix flow-control error handling
USB: serial: cp210x: fix control-characters error handling
USB: serial: io_edgeport: drop unused descriptor helper
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, qla2xxx,
target, smartpqi, lpfc, mpt3sas).
The core change causing the most churn was replacing the command
request field request with a macro, allowing us to offset map to it
and remove the redundant field; the same was also done for the tag
field.
The most impactful change is the final removal of scsi_ioctl, which
has been deprecated for over a decade"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (293 commits)
scsi: ufs: Fix ufshcd_request_sense_async() for Samsung KLUFG8RHDA-B2D1
scsi: ufs: ufs-exynos: Fix static checker warning
scsi: mpt3sas: Use the proper SCSI midlayer interfaces for PI
scsi: lpfc: Use the proper SCSI midlayer interfaces for PI
scsi: lpfc: Copyright updates for 14.0.0.1 patches
scsi: lpfc: Update lpfc version to 14.0.0.1
scsi: lpfc: Add bsg support for retrieving adapter cmf data
scsi: lpfc: Add cmf_info sysfs entry
scsi: lpfc: Add debugfs support for cm framework buffers
scsi: lpfc: Add support for maintaining the cm statistics buffer
scsi: lpfc: Add rx monitoring statistics
scsi: lpfc: Add support for the CM framework
scsi: lpfc: Add cmfsync WQE support
scsi: lpfc: Add support for cm enablement buffer
scsi: lpfc: Add cm statistics buffer support
scsi: lpfc: Add EDC ELS support
scsi: lpfc: Expand FPIN and RDF receive logging
scsi: lpfc: Add MIB feature enablement support
scsi: lpfc: Add SET_HOST_DATA mbox cmd to pass date/time info to firmware
scsi: fc: Add EDC ELS definition
...
Johan writes:
USB-serial fix for 5.15-rc1
Here's a single fix for a pl2303 type detection regression, and which
has been in linux-next over night.
* tag 'usb-serial-5.15-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: pl2303: fix GL type detection
