Instead of maintaining a single-linked list of devices that must be
searched linearly in .remove() just use spi_set_drvdata() to remember the
link between the spi device and the driver struct. Then the global list
and the next member can be dropped.
This simplifies the driver, reduces the memory footprint and the time to
search the list. Also it makes obvious that there is always a corresponding
driver struct for a given device in .remove(), so the error path for
!max3421_hcd can be dropped, too.
As a side effect this fixes a data inconsistency when .probe() races with
itself for a second max3421 device in manipulating max3421_hcd_list. A
similar race is fixed in .remove(), too.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211018204028.2914597-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of USB_DR_MODE_PERIPHERAL, the OTG clock is disabled at the end of
the probe (it is not the case if USB_DR_MODE_HOST or USB_DR_MODE_OTG).
The clock is then enabled on udc_start.
If dwc2_drd_role_sw_set is called before udc_start (it is the case if the
usb cable is plugged at boot), GOTGCTL and GUSBCFG registers cannot be
read/written, so session cannot be overridden.
To avoid this case, check the ll_hw_enabled value and enable the clock if
it is available, and disable it after the override.
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-3-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of forcing the role to Device, check the dr_mode configuration.
If the core is Host only, force the mode to Host, this to avoid the
dwc2_force_mode warning:
WARNING: CPU: 1 PID: 21 at drivers/usb/dwc2/core.c:615 dwc2_drd_init+0x104/0x17c
When forcing mode to Host, dwc2_force_mode may sleep the time the host
role is applied. To avoid sleeping while atomic context, move the call
to dwc2_force_mode after spin_unlock_irqrestore. It is safe, as
interrupts are not yet unmasked here.
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-2-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While going into S3 or S4 suspend, an OHCI host controller can
generate interrupt requests if the INTR_SF enable flag is set. The
interrupt handler routine isn't prepared for this and it doesn't turn
off the flag, causing an interrupt storm.
To fix this problem, make ohci_rh_suspend() always disable INTR_SF
interrupts after processing the done list and the ED unlinks but
before the controller goes into the suspended (non-UsbOperational)
state. There's no reason to leave the flag enabled, since a
suspended controller doesn't generate Start-of-Frame packets.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Link: https://lore.kernel.org/r/1634095928-29639-1-git-send-email-zhuyinbo@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since function drivers will still be active until dwc3_disconnect_gadget()
is called, some applications will continue to queue packets to DWC3
gadget. This can lead to a flood of messages regarding failed ep queue,
as the endpoint is in the process of being disabled. Change the log
level to debug, so that it can be enabled when debugging issues.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20211018192647.32121-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Struct pci_driver contains a struct device_driver, so for PCI devices, it's
easy to convert a device_driver * to a pci_driver * with to_pci_driver().
The device_driver * is in struct device, so we don't need to also keep
track of the pci_driver * in struct pci_dev.
Replace pdev->driver with to_pci_driver(). This is a step toward removing
pci_dev->driver.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20211004125935.2300113-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The DEF_SCSI_QCMD() macro passes the addresses of the SCSI host lock and
also that of the scsi_done function to the queuecommand_lck() function
implementations. Remove the 'scsi_done' argument since its address is
now a constant and instead call 'scsi_done' directly from inside the
queuecommand_lck() functions.
Link: https://lore.kernel.org/r/20211007204618.2196847-14-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Johan writes:
USB-serial fixes for 5.15-rc6
Here are some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.15-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: add EM9191 QDL support
USB: serial: option: add Quectel EC200S-CN module support
USB: serial: option: add prod. id for Quectel EG91
USB: serial: option: add Telit LE910Cx composition 0x1204
tools/testing/selftests/net/ioam6.sh
7b1700e009 ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make the drivers which use single-byte netdev addresses
(netdev->addr_len == 1) use the appropriate address setting
helpers.
arcnet copies from int variables and io reads a lot, so
add a helper for arcnet drivers to use.
Similar helper could be reused for phonet and appletalk
but there isn't any good central location where we could
put it, and netdevice.h is already very crowded.
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for HSI
Link: https://lore.kernel.org/r/20211012142757.4124842-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 7c75bde329 ("usb: musb: musb_dsps: request_irq() after
initializing musb") has inverted the calls to
dsps_setup_optional_vbus_irq() and dsps_create_musb_pdev() without
updating correctly the error path. dsps_create_musb_pdev() allocates and
registers a new platform device which must be unregistered and freed
with platform_device_unregister(), and this is missing upon
dsps_setup_optional_vbus_irq() error.
While on the master branch it seems not to trigger any issue, I observed
a kernel crash because of a NULL pointer dereference with a v5.10.70
stable kernel where the patch mentioned above was backported. With this
kernel version, -EPROBE_DEFER is returned the first time
dsps_setup_optional_vbus_irq() is called which triggers the probe to
error out without unregistering the platform device. Unfortunately, on
the Beagle Bone Black Wireless, the platform device still living in the
system is being used by the USB Ethernet gadget driver, which during the
boot phase triggers the crash.
My limited knowledge of the musb world prevents me to revert this commit
which was sent to silence a robot warning which, as far as I understand,
does not make sense. The goal of this patch was to prevent an IRQ to
fire before the platform device being registered. I think this cannot
ever happen due to the fact that enabling the interrupts is done by the
->enable() callback of the platform musb device, and this platform
device must be already registered in order for the core or any other
user to use this callback.
Hence, I decided to fix the error path, which might prevent future
errors on mainline kernels while also fixing older ones.
Fixes: 7c75bde329 ("usb: musb: musb_dsps: request_irq() after initializing musb")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211005221631.1529448-1-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clang does not understand the "mrc%?" syntax:
drivers/usb/gadget/udc/pxa25x_udc.c:2330:11: error: invalid % escape in inline assembly string
I don't understand it either, but removing the %? here gets it to build.
This is probably wrong and someone else should do a proper patch.
Any suggestions?
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210927123830.1278953-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EP IN is hard-coded as ASYNC both in f_uac1 and f_uac2 but u_audio sends
steady number of audio frames in each USB packet, without any control.
This patch adds 'Playback Pitch 1000000' ctl analogous to the existing
'Capture Pitch 1000000' ctl. The calculation of playback req->length in
u_audio_iso_complete respects the Playback Pitch ctl value to 1ppm now.
Max. value for Playback Pitch is configured by the existing parameter
uac2_opts->fb_max, used also for the Capture Pitch.
Since the EP IN packet size can be increased by uac2_opts->fb_max now,
maxPacketSize for the playback direction is calculated by the same
algorithm as for the async capture direction in
f_uac2.c:set_ep_max_packet_size.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20211013073934.36476-1-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The command ring pointer is located at [6:63] bits of the command
ring control register (CRCR). All the control bits like command stop,
abort are located at [0:3] bits. While aborting a command, we read the
CRCR and set the abort bit and write to the CRCR. The read will always
give command ring pointer as all zeros. So we essentially write only
the control bits. Since we split the 64 bit write into two 32 bit writes,
there is a possibility of xHC command ring stopped before the upper
dword (all zeros) is written. If that happens, xHC updates the upper
dword of its internal command ring pointer with all zeros. Next time,
when the command ring is restarted, we see xHC memory access failures.
Fix this issue by only writing to the lower dword of CRCR where all
control bits are located.
Cc: stable@vger.kernel.org
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Root-cause:
There is an issue like endpoint is not recognized as primed, when bus
have more pressure and the add dTD tripwire semaphore (ATDTW bit in
USBCMD register) that can cause the controller to ignore a dTD that is
added to a primed endpoint.
This issue observed with the Windows10 host machine.
Workaround:
The software must implement a periodic cycle, and check for each dTD,
if the endpoint is primed. It can do this by reading the corresponding
bits in the ENDPTPRIME and ENDPTSTAT registers. If these bits are read
at 0, the software needs to re-prime the endpoint by writing 1 to the
corresponding bit in the ENDPTPRIME register.
Added conditional revision check of 2.20[CI_REVISION_22].
Link: https://lore.kernel.org/linux-usb/SJ0PR02MB8644CBBA848A0F68323F1AA5D4D99@SJ0PR02MB8644.namprd02.prod.outlook.com/
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20210913140005.955699-1-piyush.mehta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.15-rc5 that resolve a number of
reported issues:
- gadget driver fixes
- xhci build warning fixes
- build configuration fix
- cdc-acm tty handling fixes
- cdc-wdm fix
- typec fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: cdc-acm: fix break reporting
USB: cdc-acm: fix racy tty buffer accesses
usb: gadget: f_uac2: fixed EP-IN wMaxPacketSize
usb: cdc-wdm: Fix check for WWAN
usb: chipidea: ci_hdrc_imx: Also search for 'phys' phandle
usb: typec: tcpm: handle SRC_STARTUP state if cc changes
usb: typec: tcpci: don't handle vSafe0V event if it's not enabled
usb: typec: tipd: Remove dependency on "connector" child fwnode
Partially revert "usb: Kconfig: using select for USB_COMMON dependency"
usb: dwc3: gadget: Revert "set gadgets parent to the right controller"
usb: xhci: tegra: mark PM functions as __maybe_unused
Pull ARM SoC fixes from Arnd Bergmann:
"This is a larger than normal update for Arm SoC specific code, most of
it in device trees, but also drivers and the omap and at91/sama7
platforms:
- There are four new entries to the MAINTAINERS file: Sven Peter and
Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar,
and Vignesh Raghavendra for TI K3
- Build fixes to address randconfig warnings in sharpsl, dove, omap1,
and qcom platforms as well as the scmi and op-tee subsystems
- Regression fixes for missing CONFIG_FB and other options for
several defconfigs
- Several bug fixes for the newly added Microchip SAMA7 platform,
mostly regarding power management
- Missing SMP barriers to protect accesses to SCMI virtio device
- Regression fixes for TI OMAP, including a boot-time hang on am335x.
- Lots of bug fixes for NXP i.MX, mostly addressing incorrect
settings in devicetree files, and one revert for broken suspend.
- Fixes for ARM Juno/Vexpress devicetree files, addressing a couple
of schema warnings.
- Regression fixes for qualcomm SoC specific drivers and devicetree
files, reverting an mdt_loader change and at least pastially
reverting some of the 5.15 DTS changes, plus some minor bugfixes"
* tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (64 commits)
MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer
MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer
firmware: arm_scmi: Add proper barriers to scmi virtio device
firmware: arm_scmi: Simplify spinlocks in virtio transport
ARM: dts: omap3430-sdp: Fix NAND device node
bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
ARM: sharpsl_param: work around -Wstringop-overread warning
ARM: defconfig: gemini: Restore framebuffer
ARM: dove: mark 'putc' as inline
ARM: omap1: move omap15xx local bus handling to usb.c
MAINTAINERS: Add Vignesh to TI K3 platform maintainership
arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
arm64: dts: ls1028a: fix eSDHC2 node
arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins
ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs
ARM: at91: pm: preload base address of controllers in tlb
ARM: at91: pm: group constants and addresses loading
ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail
...
This reverts commit ce3e90d5a0.
The commit in question added list of quirky hubs, but the match
implementation clearly hasn't been tested at all.
First, hub_udev->dev.parent does not represent a USB interface so using
to_usb_interface() makes no sense and we'd be passing a random pointer
to usb_match_id().
Second, if hub_udev is a root hub it doesn't even even represent a USB
device.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes: ce3e90d5a0 ("usb: misc: ehset: Workaround for "special" hubs")
Cc: Razvan Heghedus <heghedus.razvan@gmail.com>
Link: https://lore.kernel.org/r/20211007090601.19156-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following checkpatch.pl warnings:
drivers/usb/core/config.c:989: CHECK:ALLOC_SIZEOF_STRUCT: Prefer kzalloc(sizeof(*bos)...) over kzalloc(sizeof(struct usb_bos_descriptor)...)
drivers/usb/core/config.c:1010: CHECK:ALLOC_SIZEOF_STRUCT: Prefer kzalloc(sizeof(*dev->bos)...) over kzalloc(sizeof(struct usb_host_bos)...)
Signed-off-by: Robert Greener <rob@robgreener.com>
Link: https://lore.kernel.org/r/20211001151350.ijiexr3ebwvypmdd@shortbread
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
