Under some conditions, USB gadget devices can show allocated buffer
contents to a host. Fix this up by zero-allocating them so that any
extra data will all just be zeros.
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Tested-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes USB hosts can ask for buffers that are too large from endpoint
0, which should not be allowed. If this happens for OUT requests, stall
the endpoint, but for IN requests, trim the request size to the endpoint
buffer size.
Co-developed-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make xhci_disable_slot() synchronous, thus ensuring it, and
xhci_free_dev() calling it return after xHC controller completes
the disable slot command.
Otherwise the roothub and xHC host may runtime suspend, and clear the
command ring while the disable slot command is being processed.
This causes a command completion mismatch as the completion event can't
be mapped to the correct command.
Command ring gets out of sync and commands time out.
Driver finally assumes host is unresponsive and bails out.
usb 2-4: USB disconnect, device number 10
xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event
...
xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:0d.0: HC died; cleaning up
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.
This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.
So always take XHCI_RESET_ON_RESUME into account to solve the issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, can and netfilter.
Current release - regressions:
- bpf, sockmap: re-evaluate proto ops when psock is removed from
sockmap
Current release - new code bugs:
- bpf: fix bpf_check_mod_kfunc_call for built-in modules
- ice: fixes for TC classifier offloads
- vrf: don't run conntrack on vrf with !dflt qdisc
Previous releases - regressions:
- bpf: fix the off-by-two error in range markings
- seg6: fix the iif in the IPv6 socket control block
- devlink: fix netns refcount leak in devlink_nl_cmd_reload()
- dsa: mv88e6xxx: fix "don't use PHY_DETECT on internal PHY's"
- dsa: mv88e6xxx: allow use of PHYs on CPU and DSA ports
Previous releases - always broken:
- ethtool: do not perform operations on net devices being
unregistered
- udp: use datalen to cap max gso segments
- ice: fix races in stats collection
- fec: only clear interrupt of handling queue in fec_enet_rx_queue()
- m_can: pci: fix incorrect reference clock rate
- m_can: disable and ignore ELO interrupt
- mvpp2: fix XDP rx queues registering
Misc:
- treewide: add missing includes masked by cgroup -> bpf.h
dependency"
* tag 'net-5.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (82 commits)
net: dsa: mv88e6xxx: allow use of PHYs on CPU and DSA ports
net: wwan: iosm: fixes unable to send AT command during mbim tx
net: wwan: iosm: fixes net interface nonfunctional after fw flash
net: wwan: iosm: fixes unnecessary doorbell send
net: dsa: felix: Fix memory leak in felix_setup_mmio_filtering
MAINTAINERS: s390/net: remove myself as maintainer
net/sched: fq_pie: prevent dismantle issue
net: mana: Fix memory leak in mana_hwc_create_wq
seg6: fix the iif in the IPv6 socket control block
nfp: Fix memory leak in nfp_cpp_area_cache_add()
nfc: fix potential NULL pointer deref in nfc_genl_dump_ses_done
nfc: fix segfault in nfc_genl_dump_devices_done
udp: using datalen to cap max gso segments
net: dsa: mv88e6xxx: error handling for serdes_power functions
can: kvaser_usb: get CAN clock frequency from device
can: kvaser_pciefd: kvaser_pciefd_rx_error_frame(): increase correct stats->{rx,tx}_errors counter
net: mvpp2: fix XDP rx queues registering
vmxnet3: fix minimum vectors alloc issue
net, neigh: clear whole pneigh_entry at alloc time
net: dsa: mv88e6xxx: fix "don't use PHY_DETECT on internal PHY's"
...
This reverts commit cefdd52fa0.
On sc7180-trogdor class devices with 'fw_devlink=permissive' and KASAN
enabled, you'll see a Use-After-Free reported at bootup.
The root of the problem is that dwc3_qcom_of_register_core() is adding
a devm-allocated "tx-fifo-resize" property to its device tree node
using of_add_property().
The issue is that of_add_property() makes a _permanent_ addition to
the device tree that lasts until reboot. That means allocating memory
for the property using "devm" managed memory is a terrible idea since
that memory will be freed upon probe deferral or device unbinding.
Let's revert the patch since the system is still functional without
it. The fact that of_add_property() makes a permanent change is extra
fodder for those folks who were aruging that the device tree isn't
really the right way to pass information between parts of the
driver. It is an exercise left to the reader to submit a patch
re-adding the new feature in a way that makes everyone happier.
Fixes: cefdd52fa0 ("usb: dwc3: dwc3-qcom: Enable tx-fifo-resize property by default")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20211207094327.1.Ie3cde3443039342e2963262a4c3ac36dc2c08b30@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann says:
====================
bpf 2021-12-08
We've added 12 non-merge commits during the last 22 day(s) which contain
a total of 29 files changed, 659 insertions(+), 80 deletions(-).
The main changes are:
1) Fix an off-by-two error in packet range markings and also add a batch of
new tests for coverage of these corner cases, from Maxim Mikityanskiy.
2) Fix a compilation issue on MIPS JIT for R10000 CPUs, from Johan Almbladh.
3) Fix two functional regressions and a build warning related to BTF kfunc
for modules, from Kumar Kartikeya Dwivedi.
4) Fix outdated code and docs regarding BPF's migrate_disable() use on non-
PREEMPT_RT kernels, from Sebastian Andrzej Siewior.
5) Add missing includes in order to be able to detangle cgroup vs bpf header
dependencies, from Jakub Kicinski.
6) Fix regression in BPF sockmap tests caused by missing detachment of progs
from sockets when they are removed from the map, from John Fastabend.
7) Fix a missing "no previous prototype" warning in x86 JIT caused by BPF
dispatcher, from Björn Töpel.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add selftests to cover packet access corner cases
bpf: Fix the off-by-two error in range markings
treewide: Add missing includes masked by cgroup -> bpf dependency
tools/resolve_btfids: Skip unresolved symbol warning for empty BTF sets
bpf: Fix bpf_check_mod_kfunc_call for built-in modules
bpf: Make CONFIG_DEBUG_INFO_BTF depend upon CONFIG_BPF_SYSCALL
mips, bpf: Fix reference to non-existing Kconfig symbol
bpf: Make sure bpf_disable_instrumentation() is safe vs preemption.
Documentation/locking/locktypes: Update migrate_disable() bits.
bpf, sockmap: Re-evaluate proto ops when psock is removed from sockmap
bpf, sockmap: Attach map progs to psock early for feature probes
bpf, x86: Fix "no previous prototype" warning
====================
Link: https://lore.kernel.org/r/20211208155125.11826-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In cdnsp_endpoint_init(), cdnsp_ring_alloc() is assigned to pep->ring
and there is a dereference of it in cdnsp_endpoint_init(), which could
lead to a NULL pointer dereference on failure of cdnsp_ring_alloc().
Fix this bug by adding a check of pep->ring.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_USB_CDNSP_GADGET=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@vger.kernel.org>
Acked-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130172700.206650-1-zhou1615@umn.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.
The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.
Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.
The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.
Fixes: ff0e50d356 ("xhci: Fix command ring pointer corruption while aborting a command")
Cc: stable@vger.kernel.org
Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is another branded 8153 device that doesn't work well with LPM:
r8152 2-2.1:1.0 enp0s13f0u2u1: Stop submitting intr, status -71
Disable LPM to resolve the issue.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan writes:
USB-serial fixes for 5.16-rc3
Here's a fix for a pl2303 type-detection issue and some new modem
devices ids.
All but the last commit have been in linux-next, and with no reported
issues.
* tag 'usb-serial-5.16-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Fibocom FM101-GL variants
USB: serial: pl2303: fix GC type detection
USB: serial: option: add Telit LE910S1 0x9200 composition
it is not allow to create sub group under os_desc,
/sys/kernel/config/usb_gadget/dummy/os_desc # mkdir dummy
mkdir: can't create directory 'dummy': Operation not permitted
no one will kmalloc() os_desc entry and kfree(os_desc) will never be called.
static void os_desc_attr_release(struct config_item *item)
{
struct os_desc *os_desc = to_os_desc(item);
kfree(os_desc);
}
remove struct os_desc definition, to_os_desc() and os_desc_attr_release().
Reviewed-by: Jack Pham <quic_jackp@quicinc.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1637211213-16400-3-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC hardware can only have one slot in default state with address 0
waiting for a unique address at a time, otherwise "undefined behavior
may occur" according to xhci spec 5.4.3.4
The address0_mutex exists to prevent this across both xhci roothubs.
If hub_port_init() fails, it may unlock the mutex and exit with a xhci
slot in default state. If the other xhci roothub calls hub_port_init()
at this point we end up with two slots in default state.
Make sure the address0_mutex protects the slot default state across
hub_port_init() retries, until slot is addressed or disabled.
Note, one known minor case is not fixed by this patch.
If device needs to be reset during resume, but fails all hub_port_init()
retries in usb_reset_and_verify_device(), then it's possible the slot is
still left in default state when address0_mutex is unlocked.
Cc: <stable@vger.kernel.org>
Fixes: 638139eb95 ("usb: hub: allow to process more usb hub events in parallel")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211115221630.871204-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code that enables either BC_LVL or COMP_CHNG interrupt in tcpm_set_cc
wrongly assumes that the interrupt is unmasked by writing 1 to the apropriate
bit in the mask register. In fact, interrupts are enabled when the mask
is 0, so the tcpm_set_cc enables interrupt for COMP_CHNG when it expects
BC_LVL interrupt to be enabled.
This causes inability of the driver to recognize cable unplug events
in host mode (unplug is recognized only via a COMP_CHNG interrupt).
In device mode this bug was masked by simultaneous triggering of the VBUS
change interrupt, because of loss of VBUS when the port peer is providing
power.
Fixes: 48242e3053 ("usb: typec: fusb302: Revert "Resolve fixed power role contract setup"")
Cc: stable <stable@vger.kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/20211108102833.2793803-1-megous@megous.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/usb/dwc2/hcd_queue.c:1744:25: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
delay = ktime_set(0, DWC2_RETRY_WAIT_DELAY);
^
drivers/usb/dwc2/hcd_queue.c:62:34: note: expanded from macro 'DWC2_RETRY_WAIT_DELAY'
#define DWC2_RETRY_WAIT_DELAY (1 * 1E6L)
^
1 error generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for a floating point value in this driver, as
the value is only used as a parameter to a function that expects an
integer type. Use NSEC_PER_MSEC, which is the same integer value as
'1E6L', to avoid changing functionality but fix the error.
Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: a8083d42b1
Fixes: 6ed30a7d8e ("usb: dwc2: host: use hrtimer for NAK retries")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: John Keeping <john@metanate.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211105145802.2520658-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added updating of request frame number for elapsed frames,
otherwise frame number will remain as previous use of request.
This will allow function driver to correctly track frames in
case of Missed ISOC occurs.
Added setting request actual length to 0 for elapsed frames.
In Slave mode when pushing data to RxFIFO by dwords, request
actual length incrementing accordingly. But before whole packet
will be pushed into RxFIFO and send to host can occurs Missed
ISOC and data will not send to host. So, in this case request
actual length should be reset to 0.
Fixes: 91bb163e1e ("usb: dwc2: gadget: Fix ISOC flow for BDMA and Slave")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/c356baade6e9716d312d43df08d53ae557cb8037.1636011277.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The programming guide noted that the driver needs to verify if the link
state is in U0 before executing the Start Transfer command. If it's not
in U0, the driver needs to perform remote wakeup. This is not accurate.
If the link state is in U1/U2, then the controller will not respond to
link recovery request from DCTL.ULSTCHNGREQ. The Start Transfer command
will trigger a link recovery if it is in U1/U2. A clarification will be
added to the programming guide for all controller versions.
The current implementation shouldn't cause any functional issue. It may
occasionally report an invalid time out warning from failed link
recovery request. The driver will still go ahead with the Start Transfer
command if the remote wakeup fails. The new change only initiates remote
wakeup where it is needed, which is when the link state is in L1/L2/U3.
Fixes: c36d8e947a ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/05b4a5fbfbd0863fc9b1d7af934a366219e3d0b4.1635204761.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The End Transfer command from a stream endpoint will generate a NoStream
event, and we should ignore it. Currently we set the flag
DWC3_EP_IGNORE_NEXT_NOSTREAM to track this prior to sending the command,
and it will be cleared on the next stream event. However, a stream event
may be generated before the End Transfer command completion and
prematurely clear the flag. Fix this by setting the flag on End Transfer
completion instead.
Fixes: 140ca4cfea ("usb: dwc3: gadget: Handle stream transfers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cee1253af4c3600edb878d11c9c08b040817ae23.1635203975.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
