Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes to resolve some
reported problems:
- led tty trigger fixes based on review and were acked by the led
maintainer
- revert a max310x serial driver patch as it was causing problems
- revert a pty change as it was also causing problems
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "drivers:tty:pty: Fix a race causing data loss on close"
Revert "serial: max310x: rework RX interrupt handling"
leds: trigger/tty: Use led_set_brightness_sync() from workqueue
leds: trigger: Fix error path to not unlock the unlocked mutex
In "tx_empty", we should poll TC bit in both DMA and PIO modes (instead of
TXE) to check transmission data register has been transmitted independently
of the FIFO mode. TC indicates that both transmit register and shift
register are empty. When shift register is empty, tx_empty should return
TIOCSER_TEMT instead of TC value.
Cleans the USART_CR_TC TCCF register define (transmission complete clear
flag) as it is duplicate of USART_ICR_TCCF.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-13-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Transmission complete error is sent when ISR_TC is not set. If port closure
is requested despite data in TDR / TX FIFO has not been sent (because of
flow control), ISR_TC is not set and error message is sent on port closure
but also when a new port is opened.
Flush the data when port is closed, so the error isn't printed twice upon
next port opening.
Fixes: 64c32eab66 ("serial: stm32: Add support of TC bit status check")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-12-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CTS/RTS GPIOs support that has been added recently to STM32 UART driver has
introduced scheduled code in a set_termios part protected by a spin lock.
This generates a potential deadlock scenario:
Chain exists of:
&irq_desc_lock_class --> console_owner --> &port_lock_key
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&port_lock_key);
lock(console_owner);
lock(&port_lock_key);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
4 locks held by stty/766:
Move the scheduled code after the spinlock.
Fixes: 6cf61b9bd7 ("tty: serial: Add modem control gpio support for STM32 UART")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-8-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes several issue with wake-up handling:
- the WUF irq is handled several times at wake-up
- the USART is disabled / enabled at suspend to set wake-up flag.
It can cause glitches during RX.
This patch fix those issues:
- clear wake-up flag and disable wake-up irq in WUF irq handling
- enable wake-up from low power on start bit detection at port
configuration
- Unmask the wake-up flag irq at suspend and mask it at resume
In addition, pm_wakeup_event handling is moved from receice_chars to WUF
irq handling.
Fixes: 270e5a74fe ("serial: stm32: add wakeup mechanism")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-7-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Deadlock issue is seen when enabling CONFIG_PROVE_LOCKING=Y, and uart
console as wakeup source. Deadlock occurs when resuming from low power
mode if system is waked up via usart console.
The deadlock is triggered 100% when also disabling console suspend prior
to go to suspend.
Simplified call stack, deadlock condition:
- stm32_console_write <-- spin_lock already held
- print_circular_bug
- pm_wakeup_dev_event <-- triggers lockdep as seen above
- stm32_receive_chars
- stm32_interrupt <-- wakeup via uart console, takes the lock
So, revisit spin_lock in stm32-usart driver:
- there is no need to hold the lock to access ICR (atomic clear of status
flags)
- only hold the lock inside stm32_receive_chars() routine (no need to
call pm_wakeup_dev_event with lock held)
- keep stm32_transmit_chars() routine called with lock held
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-6-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TX and RX FIFO thresholds may be cleared after suspend/resume, depending
on the low power mode.
Those configurations (done in startup) are not effective for UART console,
as:
- the reference manual indicates that FIFOEN bit can only be written when
the USART is disabled (UE=0)
- a set_termios (where UE is set) is requested firstly for console
enabling, before the startup.
Fixes: 84872dc448 ("serial: stm32: add RX and TX FIFO flush")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-5-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Incorrect characters are observed on console during boot. This issue occurs
when init/main.c is modifying termios settings to open /dev/console on the
rootfs.
This patch adds a waiting loop in set_termios to wait for TX shift register
empty (and TX FIFO if any) before stopping serial port.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-4-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe and remove orders are wrong as the uart_port is registered
before saving device data in the probe, and unregistered after DMA
resource deallocation in the remove. uart_port registering should be
done at the end of probe and unregistering should be done at the begin of
remove to avoid resource allocation issues.
Fix probe and remove orders. This enforce resource allocation occur at
proper time.
Terminate both DMA rx and tx transfers before removing device.
Move pm_runtime after uart_remove_one_port() call in remove() to keep the
probe error path.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Earlycon support is identical to S3C2410, but Apple SoCs also need
MMIO mapped as nGnRnE. This is handled generically for normal drivers
including the normal UART path here, but earlycon uses fixmap and
runs before that scaffolding is ready.
Since this is the only case where we need this fix, it makes more
sense to do it here in the UART driver instead of introducing a
whole fdt nonposted-mmio resolver just for earlycon/fixmap.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210304213902.83903-26-marcan@marcan.st
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apple SoCs are a distant descendant of Samsung designs and use yet
another variant of their UART style, with different interrupt handling.
In particular, this variant has the following differences with existing
ones:
* It includes a built-in interrupt controller with different registers,
using only a single platform IRQ
* Internal interrupt sources are treated as edge-triggered, even though
the IRQ output is level-triggered. This chiefly affects the TX IRQ
path: the driver can no longer rely on the TX buffer empty IRQ
immediately firing after TX is enabled, but instead must prime the
FIFO with data directly.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210304213902.83903-25-marcan@marcan.st
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Split out s3c24xx_serial_tx_chars from s3c24xx_serial_tx_irq,
where only the latter acquires the port lock. This will be necessary
on platforms which have edge-triggered IRQs, as we need to call
s3c24xx_serial_tx_chars to kick off transmission from outside IRQ
context, with the port lock held.
* Rename s3c24xx_serial_rx_chars to s3c24xx_serial_rx_irq for
consistency with the above. All it does now is call two other
functions anyway.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210304213902.83903-22-marcan@marcan.st
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of patching a single global ops structure depending on the port
type, use a separate s3c64xx_serial_ops for the S3C64XX type. This
allows us to mark the structures as const.
Also split out s3c64xx_serial_shutdown into a separate function now that
we have a separate ops structure; this avoids excessive branching
control flow and mirrors s3c64xx_serial_startup. tx_claimed and
rx_claimed are only used in the S3C24XX functions.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210304213902.83903-19-marcan@marcan.st
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When SERIAL_IMX_EARLYCON is enabled, and SERIAL_CORE is disabled,
Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for SERIAL_EARLYCON
Depends on [n]: TTY [=y] && HAS_IOMEM [=y] && SERIAL_CORE [=n]
Selected by [y]:
- SERIAL_IMX_EARLYCON [=y] && TTY [=y] && HAS_IOMEM [=y] && (ARCH_MXC [=y] || COMPILE_TEST [=n]) && OF [=y]
This is because SERIAL_IMX_EARLYCON selects SERIAL_EARLYCON,
without selecting SERIAL_CORE, despite that config option depending
on SERIAL_CORE.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Link: https://lore.kernel.org/r/20210225044248.4745-1-julianbraha@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set tty_ldisc_ops::owner to THIS_MODULE. This has no effect currently as
n_tty cannot be built as a module. If someone ever tries to modularize
tty, we wouldn't manage module's reference count as in other ldiscs. So
fix this just in case.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-9-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First, it is never checked. Second, use of it as a debugging aid is
at least questionable. With the current tools, I don't think anyone used
this kind of thing for debugging purposes for years.
On the top of that, e.g. serdev does not set this field of tty_ldisc_ops
at all.
So get rid of this legacy.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the driver is still marked as maintained in MAINTAINERS, Comtrol
does not really care about this ancient driver. They are still
manufacturing serial devices, but those are controlled only by
out-of-tree drivers.
Comtrol didn't answer my pings, so this driver is apparently
unmaintained. Aside from that, the driver was untouched for years, only
whole-tree changes happened during the past years. The driver needs much
more care, so drop it for now. If someone steps up to reintroduce it,
they need to clean it up first.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cyclades driver was orphaned by commit d459883e6c (MAINTAINERS:
remove two dead e-mail) 13 years ago. Noone stepped up to take care of
them and to fix all the issues the driver has.
On the top of that, there is no way to obtain the firmware for Z cards
from the vendor as cyclades.com ceased to exist.
So it's time to drop the driver with all its traces.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
