Commit d948e6ca18 ("spi: add power control when set_cs") added generic
runtime PM handling, but also changed the return value to be 1 instead
of 0 that we had earlier as pm_runtime_get functions return a positve
value on success.
This causes SPI devices to return errors for cases where they do:
ret = spi_setup(spi);
if (ret)
return ret;
As in many cases the SPI devices do not check for if (ret < 0).
Let's fix this by setting the status to 0 on succeess after the
runtime PM calls. Let's not return 0 at the end of the function
as this might break again later on if the function changes and
starts returning status again.
Fixes: d948e6ca18 ("spi: add power control when set_cs")
Cc: Luhua Xu <luhua.xu@mediatek.com>
Cc: wsd_upstream@mediatek.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20191111195334.44833-1-tony@atomide.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both omap2_mcspi_tx_dma() and omap2_mcspi_rx_dma() are only called from
omap2_mcspi_txrx_dma() and omap2_mcspi_txrx_dma() is always called after
making sure that mcspi_dma->dma_rx and mcspi_dma->dma_tx are not NULL
(see omap2_mcspi_transfer_one()).
Therefore remove redundant NULL checks for omap2_mcspi->dma_tx and
omap2_mcspi->dma_rx pointers in omap2_mcspi_tx_dma() and
omap2_mcspi_rx_dma() respectively.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191109041827.26934-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Zynq QSPI controller features 2 CS. When the num-cs DT property
is set to 2, the hardware will be initialized to support having two
devices connected over each CS.
In this case, both CS lines are driven by the state of the U_PAGE
(upper page) bit. When unset, the lower page (CS0) is selected,
otherwise it is the upper page (CS1).
Change tested on a custom design featuring two SPI-NORs with different
CS on the Zynq-7000 QSPI bus.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-8-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Supporting more than one CS will need some tweaking of the linear
configuration register which is (rightfully) initialized in the
hardware initialization helper. The extra initialization needs the
knowledge of the actual number of CS, which is retrieved by reading
the value of the num-cs DT property.
As the initialization helper is called pretty early and might be
called much later in the probe without side effect, let's delay it a
bit so that the number of CS will be available when running this
helper. This way, adding support for multiple CS lines in a next patch
will be eased.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-7-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The code used to assert and de-assert a chip select line is very
complicated for no reason. Simplify the logic by either setting or
resetting the concerned bit, which actually only changes an electrical
state.
Update the comment to reflect that there is no possibility to actually
choose a CS as the default (CS0) will be driven in any case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-6-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The channels spfi->tx_ch and spfi->rx_ch are not set to NULL after they
are released. As a result, they will be released again, either on the
error handling branch in the same function or in the corresponding
remove function, i.e. img_spfi_remove(). This patch fixes the bug by
setting the two members to NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1573007769-20131-1-git-send-email-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the TXX9 SPI driver to use GPIO descriptors
to control the GPIO chip selects.
As the driver was clearly (ab)using the device tree "reg"
property to offset into the global GPIO chip we have to
add a hack to counter the hack: add a 1-to-1 chip select
to GPIO offset mapping for all 16 lines on the TXX9 GPIO
chip. The details are described in a largeish comment
in the patch.
We do not need to set up the GPIO as output any more since
the core will take care of this, as well as it will handle
the polarity inversion semantics.
Cc: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073832.24038-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When rebooting system, the PMIC watchdog time loading may not be loaded
correctly when another system is feeding the PMIC watchdog, since we did
not check the watchdog busy status before loading time values.
Thus we should set the BIT_WDG_NEW bit before loading time values, that
can support multiple loads without checking busy status to make sure the
time values can be loaded successfully to avoid this potential issue.
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/5655318a7252c9ea518c2f7950a61228ab8f42bf.1572257085.git.baolin.wang@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver does the wrong thing when cs_change is set on a non-last
xfer in a message. When cs_change is set, the driver deactivates the
CS and leaves it off until a later xfer again has cs_change set whereas
it should be briefly toggling CS off and on again.
This patch brings the behaviour of the driver back in line with the
documentation and common sense. The delay of 10 us is the same as is
used by the default spi_transfer_one_message() function in spi.c.
[gregory: rebased on for-5.5 from spi tree]
Fixes: 8090d6d1a4 ("spi: atmel: Refactor spi-atmel to use SPI framework queue")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191018153504.4249-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the previous implementation of this driver, the index of the GPIO
used as CS was linked to the offset of the CS register used to
configure the transfer.
With this new implementation the first CS register not used by
internal CS is associated to all the GPIO CS. It allows to not be
anymore limited to have only 4 CS managed, now it is possible to have
in the same time until 3 internal CS and no more limit for the CS
GPIO.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-7-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
