Since commit 46164fde6b ("spi: dw: Fix Rx-only DMA transfers") if DMA
interface is enabled, then Tx-buffer must be available in each SPI
transfer. It's required since in order to activate the incoming data
reception either DMA or CPU must be pushing data out to the SPI bus.
But the DW APB SSI DMA driver code is still left in state as if Tx-buffer
might be optional, which is no longer true. Let's fix it so an error would
be returned if no Tx-buffer detected and DMA Tx would be always
enabled.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920112322.24585-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Indeed the registers content doesn't get cleared when the SPI controller
is disabled and enabled. Max burst lengths aren't changed since the Rx and
Tx DMA channels are requested on init stage and are kept acquired until
the device is removed. Obviously SPI controller FIFO depth can't be
changed. Due to all of that we can safely move the DMA Transmit and
Receive data level registers initialization to the SPI controller DMA init
stage (when the SPI controller is being probed) instead of doing it for
each SPI transfer when dma_setup is called. This shall speed the DMA-based
SPI transfer initialization up a bit, particularly if the APB bus is
relatively slow.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920112322.24585-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 530b5affc6 ("spi: fsl-dspi: fix use-after-free in remove
path") this driver causes a kernel oops:
[ 1.891065] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000080
[..]
[ 2.056973] Call trace:
[ 2.059425] dspi_setup+0xc8/0x2e0
[ 2.062837] spi_setup+0xcc/0x248
[ 2.066160] spi_add_device+0xb4/0x198
[ 2.069918] of_register_spi_device+0x250/0x370
[ 2.074462] spi_register_controller+0x4f4/0x770
[ 2.079094] dspi_probe+0x5bc/0x7b0
[ 2.082594] platform_drv_probe+0x5c/0xb0
[ 2.086615] really_probe+0xec/0x3c0
[ 2.090200] driver_probe_device+0x60/0xc0
[ 2.094308] device_driver_attach+0x7c/0x88
[ 2.098503] __driver_attach+0x60/0xe8
[ 2.102263] bus_for_each_dev+0x7c/0xd0
[ 2.106109] driver_attach+0x2c/0x38
[ 2.109692] bus_add_driver+0x194/0x1f8
[ 2.113538] driver_register+0x6c/0x128
[ 2.117385] __platform_driver_register+0x50/0x60
[ 2.122105] fsl_dspi_driver_init+0x24/0x30
[ 2.126302] do_one_initcall+0x54/0x2d0
[ 2.130149] kernel_init_freeable+0x1ec/0x258
[ 2.134520] kernel_init+0x1c/0x120
[ 2.138018] ret_from_fork+0x10/0x34
[ 2.141606] Code: 97e0b11d aa0003f3 b4000680 f94006e0 (f9404000)
[ 2.147723] ---[ end trace 26cf63e6cbba33a8 ]---
This is because since this commit, the allocation of the drivers private
data is done explicitly and in this case spi_alloc_master() won't set the
correct pointer.
Also move the platform_set_drvdata() to have both next to each other.
Fixes: 530b5affc6 ("spi: fsl-dspi: fix use-after-free in remove path")
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200928085500.28254-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull spi fixes from Mark Brown:
"A small collection of driver specific fixes, the fsl-espi and bcm-qspi
changes in particular have been causing breakage for users"
* tag 'spi-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: bcm-qspi: Fix probe regression on iProc platforms
spi: fsl-dspi: fix use-after-free in remove path
spi: fsl-espi: Only process interrupts for expected events
spi: bcm2835: Make polling_limit_us static
spi: spi-fsl-dspi: use XSPI mode instead of DMA for DPAA2 SoCs
This series mainly add the IRQ mode support for hisi-sfc-v3xx driver, and some
cleanups for the preparation of the IRQ mode.
After this patch, the device can work in IRQ mode, or if firmware doesn't
declare irq support it will fall back to Poll mode.
Patch 1-2 refactor the .exec_op() path to make it simpler and clearer.
Patch 3 factor the definition of the interrupt bits.
Patch 4 add the IRQ support of the driver.
Yicong Yang (4):
spi: hisi-sfc-v3xx: factor out IO modes configuration
spi: hisi-sfc-v3xx: factor out bus config and transfer functions
spi: hisi-sfc-v3xx: factor out the bit definition of interrupt
register
spi: hisi-sfc-v3xx: add support for IRQ mode
drivers/spi/spi-hisi-sfc-v3xx.c | 261 +++++++++++++++++++++++++++++-----------
1 file changed, 190 insertions(+), 71 deletions(-)
--
2.8.1
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
CLK_TO_US macro is used to calculate potential transfer time for various
timeout handling. However it overflows on transfer bigger than 512 bytes
because it first did (len * 8 * 1000000).
This controller typically operates at 45MHz. This patch did 2 things:
1. calculate clock / 1000000 first
2. add a 4M transfer size cap so that the final timeout in DMA reading
doesn't overflow
Fixes: 881d1ee9fe ("spi: add support for mediatek spi-nor controller")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200922114905.2942859-1-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch implementes the reporting of the effectivly used speed_hz for the
transfer by setting tfr->effective_speed_hz.
See the following patch, which adds this feature to the SPI core for more
information:
5d7e2b5ed5 spi: core: allow reporting the effectivly used speed_hz for a transfer
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200917202420.1914104-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 13d515c796 (spi: omap2-mcspi: Switch to
readl_poll_timeout()).
The amount of time spent polling for the MCSPI_CHSTAT bits to be set on
AM335x-icev2 platform is less than 1us (about 0.6us) in most cases, with
or without using DMA. So, in most cases the function need not sleep.
Also, setting the sleep_usecs to zero would not be optimal here because
ktime_add_us() used in readl_poll_timeout() is slower compared to the
direct addition used after the revert. So, it is sub-optimal to use
readl_poll_timeout in this case.
When DMA is not enabled, this revert results in an increase of about 27%
in throughput and decrease of about 20% in CPU usage. However, the CPU
usage and throughput are almost the same when used with DMA.
Therefore, fix this by reverting the commit which switched to using
readl_poll_timeout().
Fixes: 13d515c796 ("spi: omap2-mcspi: Switch to readl_poll_timeout()")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20200910122624.8769-1-a-govindraju@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series implements a number of fixes for the FSI-attached SPI
controller driver.
Changes since v1:
- Switch to a new compatible string for the restricted version of the
SPI controller, rather than a new boolean parameter.
Brad Bishop (3):
spi: fsi: Handle 9 to 15 byte transfers lengths
spi: fsi: Fix clock running too fast
spi: fsi: Fix use of the bneq+ sequencer instruction
Eddie James (3):
dt-bindings: fsi: fsi2spi: Add compatible string for restricted
version
spi: fsi: Implement restricted size for certain controllers
spi: fsi: Check mux status before transfers
.../devicetree/bindings/fsi/ibm,fsi2spi.yaml | 1 +
drivers/spi/spi-fsi.c | 139 ++++++++++++++----
2 files changed, 109 insertions(+), 31 deletions(-)
--
2.26.2
The info message was showing the mapped address of the device. To avoid
security problems, all virtual addresses are converted to __ptrval__, so
the message was useless/ugly:
[ 2.304949] xilinx_spi b0010000.spi-flash: at 0xB0010000 mapped to 0x(____ptrval____), irq=37
Use %pR instead:
[ 15.021354] xilinx_spi b0010000.spi-flash: at [mem 0xb0010000-0xb001ffff], irq=37
Signed-off-by: Ricardo Ribalda <ribalda@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20200915112936.320647-1-ribalda@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the FSI-attached SPI controllers cannot use the loop command in
programming the sequencer due to security requirements. Check the
devicetree compatibility that indicates this condition and restrict the
size for these controllers. Also, add more transfers directly in the
sequence up to the length of the sequence register.
Fixes: bbb6b2f986 ("spi: Add FSI-attached SPI controller driver")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-6-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All of the switches in N2_count_control in the counter configuration are
required to make the branch if not equal and increment command work.
Set them when using bneq+.
A side effect of this mode requires a dummy write to TDR when both
transmitting and receiving otherwise the controller won't start shifting
receive data.
It is likely not possible to avoid TDR underrun errors in this mode and
they are harmless, so do not check for them.
Fixes: bbb6b2f986 ("spi: Add FSI-attached SPI controller driver")
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-4-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a clock divider tuned to a 200MHz FSI bus frequency (the maximum). Use
of the previous divider at 200MHz results in corrupt data from endpoint
devices. Ideally the clock divider would be calculated from the FSI clock,
but that would require some significant work on the FSI driver. With FSI
frequencies slower than 200MHz, the SPI clock will simply run slower, but
safely.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-3-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If we're sending bytes over SPI, we know the FIFO is empty at the
start of the transfer. There's no reason to wait for the interrupt
telling us to start--we can just start right away. Then if we
transmit everything in one swell foop we don't even need to bother
listening for TX interrupts.
In a test of "flashrom -p ec -r /tmp/foo.bin" interrupts were reduced
from ~30560 to ~29730, about a 3% savings.
This patch looks bigger than it is because I moved a few functions
rather than adding a forward declaration. The only actual change to
geni_spi_handle_tx() was to make it return a bool indicating if there
is more to tx.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200912111716.1.Ied5e843fad0d6b733a1fb8bcfb364dd2fa889eb3@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
The arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi device tree lacks DMA
channels for DSPI, so naturally, the driver fails to probe:
[ 2.945302] fsl-dspi 2100000.spi: rx dma channel not available
[ 2.951134] fsl-dspi 2100000.spi: can't get dma channels
In retrospect, this should have been obvious, because LS2080A, LS2085A
LS2088A and LX2160A don't appear to have an eDMA module at all. Looking
again at their datasheets, the CTARE register (which is specific to XSPI
functionality) seems to be documented, so switch them to XSPI mode
instead.
Fixes: 0feaf8f5af ("spi: spi-fsl-dspi: Convert the instantiations that support it to DMA")
Reported-by: Qiang Zhao <qiang.zhao@nxp.com>
Tested-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200910121532.1138596-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We always toggle the chip select manually in spi-geni-qcom so that we
can properly implement the Linux API. There's no reason to program
this to the hardware on every transfer. Program it once at init and
be done with it.
This saves some part of a microsecond of overhead on each transfer.
While not really noticeable on any real world benchmarks, we might as
well save the time.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200912140730.2.I33e571179986850b4ec17042e813d0b08fb1b9c1@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 902481a78e ("spi: spi-geni-qcom: Actually use our FIFO") I
explained that the maximum size we could program the FIFO was
"mas->tx_fifo_depth - 3" but that I chose "mas->tx_fifo_depth()"
because I was worried about decreased bandwidth.
Since that time:
* All the interconnect patches have landed, making things run at the
proper speed.
* I've done more measurements.
This lets me confirm that there's really no downside of using the FIFO
more. Specifically I did "flashrom -p ec -r /tmp/foo.bin" on a
Chromebook and averaged over several runs.
Before: It took 6.66 seconds and 59669 interrupts fired.
After: It took 6.66 seconds and 47992 interrupts fired.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200912140730.1.Ie67fa32009b94702d56232c064f1d89065ee8836@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull spi fixes from Mark Brown:
"There's some driver specific fixes here plus one core fix for memory
leaks that could be triggered by a potential race condition when
cleaning up after we have split transfers to fit into what the
controller can support"
* tag 'spi-fix-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: stm32: fix pm_runtime_get_sync() error checking
spi: Fix memory leak on splited transfers
spi: spi-cadence-quadspi: Fix mapping of buffers for DMA reads
spi: stm32: Rate-limit the 'Communication suspended' message
spi: spi-loopback-test: Fix out-of-bounds read
spi: spi-cadence-quadspi: Populate get_name() interface
MAINTAINERS: add myself as maintainer for spi-fsl-dspi driver
The arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi device tree lacks DMA
channels for DSPI, so naturally, the driver fails to probe:
[ 2.945302] fsl-dspi 2100000.spi: rx dma channel not available
[ 2.951134] fsl-dspi 2100000.spi: can't get dma channels
In retrospect, this should have been obvious, because LS2080A, LS2085A
LS2088A and LX2160A don't appear to have an eDMA module at all. Looking
again at their datasheets, the CTARE register (which is specific to XSPI
functionality) seems to be documented, so switch them to XSPI mode
instead.
Fixes: 0feaf8f5af ("spi: spi-fsl-dspi: Convert the instantiations that support it to DMA")
Reported-by: Qiang Zhao <qiang.zhao@nxp.com>
Tested-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200910121532.1138596-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hello,
This cleans up some of the user code around calls to
dev_pm_opp_of_remove_table().
All the patches can be picked by respective maintainers directly except
for the last patch, which needs the previous two to get merged first.
These are based for 5.9-rc1.
Rajendra, Since most of these changes are related to qcom stuff, it
would be great if you can give them a try. I wasn't able to test them
due to lack of hardware.
Ulf, I had to revise the sdhci patch, sorry about that. Please pick this
one.
Diff between V1 and V2 is mentioned in each of the patches separately.
Viresh Kumar (8):
cpufreq: imx6q: Unconditionally call dev_pm_opp_of_remove_table()
drm/lima: Unconditionally call dev_pm_opp_of_remove_table()
drm/msm: Unconditionally call dev_pm_opp_of_remove_table()
mmc: sdhci-msm: Unconditionally call dev_pm_opp_of_remove_table()
spi: spi-geni-qcom: Unconditionally call dev_pm_opp_of_remove_table()
spi: spi-qcom-qspi: Unconditionally call dev_pm_opp_of_remove_table()
tty: serial: qcom_geni_serial: Unconditionally call
dev_pm_opp_of_remove_table()
qcom-geni-se: remove has_opp_table
drivers/cpufreq/imx6q-cpufreq.c | 10 ++--------
drivers/gpu/drm/lima/lima_devfreq.c | 6 +-----
drivers/gpu/drm/lima/lima_devfreq.h | 1 -
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c | 14 +++++---------
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.h | 1 -
drivers/gpu/drm/msm/dsi/dsi_host.c | 8 ++------
drivers/mmc/host/sdhci-msm.c | 14 +++++---------
drivers/spi/spi-geni-qcom.c | 13 +++++--------
drivers/spi/spi-qcom-qspi.c | 15 ++++++---------
drivers/tty/serial/qcom_geni_serial.c | 13 +++++--------
include/linux/qcom-geni-se.h | 2 --
11 files changed, 31 insertions(+), 66 deletions(-)
base-commit: f4d51dffc6
--
2.25.0.rc1.19.g042ed3e048af
