Not all RPM firmware versions have the dynamic sleep stats offset
available. Most older versions use a fixed offset of 0xdba0.
Add support for this using new SoC-specific compatibles for APQ8084,
MSM8226, MSM8916 and MSM8974.
Even older SoCs seem to use a different offset and stats format.
If needed those could be supported in the future by adding separate
compatibles for those with a different stats_config.
Cc: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211119213953.31970-3-stephan@gerhold.net
Samsung SoC drivers changes for v5.17
1. Exynos ChipID: add Exynos7885 support.
2. Exynos PMU: add Exynos850 support.
3. Minor bindings cleanup.
4. Add Exynos USIv2 (Universal Serial Interface) driver. The USI block is
a shared IP block between I2C, UART/serial and SPI. Basically one has
to choose which feature the USI block will support and later the
regular I2C/serial/SPI driver will bind and work.
This merges also one commit with dt-binding headers from my dts64
pull request.
Together with a future serial driver change, this will break the ABI.
Affected: Serial on ExynosAutov9 SADK and out-of-tree ExynosAutov9 boards
Why: To properly and efficiently support the USI with new hierarchy
of USI-{serial,SPI,I2C} devicetree nodes.
Rationale:
Recently added serial and USI support was short-sighted and did not
allow to smooth support of other features (SPI and I2C). Adding
support for USI-SPI and USI-I2C would effect in code duplication.
Adding support for different USI versions (currently supported is
USIv2 but support for v1 is planned) would cause even more code
duplication and create a solution difficult to maintain.
Since USI-serial and ExynosAutov9 have been added recently, are
considered fresh development features and there are no supported
products using them, the code/solution is being refactored in
non-backwards compatible way. The compatibility is not broken yet.
It will be when serial driver changes are accepted.
The ABI break was discussed with only known users of ExynosAutov9 and
received their permission.
* tag 'samsung-drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: soc: samsung: keep SoC driver bindings together
soc: samsung: Add USI driver
dt-bindings: soc: samsung: Add Exynos USI bindings
soc: samsung: exynos-pmu: Add Exynos850 support
dt-bindings: samsung: pmu: Document Exynos850
soc: samsung: exynos-chipid: add Exynos7885 SoC support
soc: samsung: exynos-chipid: describe which SoCs go with compatibles
Link: https://lore.kernel.org/r/20211220115405.30434-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX drivers update for 5.17:
- A number of patches from Adam Ford to update gpcv2 and blk-ctrl driver
to keep i.MX8MM VPU-H1 and i.MX8MN GPUMIX bus clocks active, and add
i.MX8MN display related domain support.
- Add optional continuous burst clock support for imx-weim bus driver.
- Call pm_runtime_put_sync_suspend() instead of pm_runtime_put() in
gpcv2 driver to prevent a sequence issue seen with i.MX8MM GPU and
MIX domain.
* tag 'imx-drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: imx8m-blk-ctrl: add i.MX8MN DISP blk-ctrl
dt-bindings: power: imx8mn: add defines for DISP blk-ctrl domains
soc: imx: gpcv2: Add dispmix and mipi domains to imx8mn
soc: imx: gpcv2: keep i.MX8MN gpumix bus clock enabled
bus: imx-weim: optionally enable continuous burst clock
soc: imx: gpcv2: keep i.MX8MM VPU-H1 bus clock active
soc: imx: gpcv2: Synchronously suspend MIX domains
Link: https://lore.kernel.org/r/20211218071427.26745-1-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
soc/tegra: Changes for v5.17-rc1
This set of changes contains some preparatory work that is shared by
several branches and trees to support DVFS via power domains.
There's also a bit of cleanup and improvements to reboot on chips that
use PSCI.
* tag 'tegra-for-5.17-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Rename core power domain
soc/tegra: pmc: Rename 3d power domains
soc/tegra: regulators: Prepare for suspend
soc/tegra: fuse: Use resource-managed helpers
soc/tegra: fuse: Reset hardware
soc/tegra: pmc: Add reboot notifier
soc/tegra: Don't print error message when OPPs not available
Link: https://lore.kernel.org/r/20211217162253.1801077-1-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
drivers: Changes for v5.17-rc1
This is an assortment of driver patches that rely on some of the changes
in the for-5.17/soc branch. These have all been acked by the respective
maintainers and go through the Tegra tree to more easily handle the
build dependency.
* tag 'tegra-for-5.17-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
media: staging: tegra-vde: Support generic power domain
spi: tegra20-slink: Add OPP support
mtd: rawnand: tegra: Add runtime PM and OPP support
mmc: sdhci-tegra: Add runtime PM and OPP support
pwm: tegra: Add runtime PM and OPP support
bus: tegra-gmi: Add runtime PM and OPP support
usb: chipidea: tegra: Add runtime PM and OPP support
soc/tegra: Add devm_tegra_core_dev_init_opp_table_common()
soc/tegra: Enable runtime PM during OPP state-syncing
Link: https://lore.kernel.org/r/20211217162253.1801077-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
USIv2 IP-core is found on modern ARM64 Exynos SoCs (like Exynos850) and
provides selectable serial protocol (one of: UART, SPI, I2C). USIv2
registers usually reside in the same register map as a particular
underlying protocol it implements, but have some particular offset. E.g.
on Exynos850 the USI_UART has 0x13820000 base address, where UART
registers have 0x00..0x40 offsets, and USI registers have 0xc0..0xdc
offsets. Desired protocol can be chosen via SW_CONF register from System
Register block of the same domain as USI.
Before starting to use a particular protocol, USIv2 must be configured
properly:
1. Select protocol to be used via System Register
2. Clear "reset" flag in USI_CON
3. Configure HWACG behavior (e.g. for UART Rx the HWACG must be
disabled, so that the IP clock is not gated automatically); this is
done using USI_OPTION register
4. Keep both USI clocks (PCLK and IPCLK) running during USI registers
modification
This driver implements the above behavior. Of course, USIv2 driver
should be probed before UART/I2C/SPI drivers. It can be achieved by
embedding UART/I2C/SPI nodes inside of the USI node (in Device Tree);
driver then walks underlying nodes and instantiates those. Driver also
handles USI configuration on PM resume, as register contents can be lost
during CPU suspend.
This driver is designed with different USI versions in mind. So it
should be relatively easy to add new USI revisions to it later.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20211204195757.8600-3-semen.protsenko@linaro.org
Tested-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
soc/tegra: Fixes for v5.16-rc6
This contains a single build fix without which ARM allmodconfig builds
are broken if -Werror is enabled.
* tag 'tegra-for-5.16-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Fix bitwise vs. logical OR warning
Link: https://lore.kernel.org/r/20211215162618.3568474-1-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CORE power domain uses name of device-tree node, which is inconsistent with
the names of PMC domains. Set the name to "core" to make it consistent.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Device-tree schema doesn't allow domain name to start with a number.
We don't use 3d domain yet in device-trees, so rename it to the name
used by Tegra TRMs: TD, TD2.
Reported-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
GENPD core now can set up domain's performance state properly while device
is RPM-suspended. Runtime PM of a device must be enabled during setup
because GENPD checks whether device is suspended and check doesn't work
while RPM is disabled. Instead of replicating the boilerplate RPM-enable
code around OPP helper for each driver, let's make OPP helper to take care
of enabling it.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use resource-managed helpers to make code cleaner and more correct,
properly releasing all resources in case of driver probe error.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The FUSE controller is enabled at a boot time. Reset it in order to put
hardware and clock into clean and disabled state.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra PMC driver implements a restart handler that supports Tegra
specific reboot commands such as placing the device into 'recovery' mode
in order to reprogram the platform. This is accomplished by setting the
appropriate bit in the PMC scratch0 register prior to rebooting the
platform.
For Tegra platforms that support PSCI or EFI, the default Tegra restart
handler is not called and the PSCI or EFI restart handler is called
instead. Hence, for Tegra platforms that support PSCI or EFI, the Tegra
specific reboot commands do not currently work. Fix this by moving the
code that programs the PMC scratch0 register into a separate reboot
notifier that will always be called on reboot.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously we assumed that devm_tegra_core_dev_init_opp_table() will
be used only by drivers that will always have device with OPP table,
but this is not true anymore. For example now Tegra30 will have OPP table
for PWM, but Tegra20 not and both use the same driver. Hence let's not
print the error message about missing OPP table in the common helper,
we can print it elsewhere.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A new warning in clang points out two instances where boolean
expressions are being used with a bitwise OR instead of logical OR:
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: note: cast one or both operands to int to silence this warning
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: note: cast one or both operands to int to silence this warning
2 warnings generated.
The motivation for the warning is that logical operations short circuit
while bitwise operations do not.
In this instance, tegra_fuse_read_spare() is not semantically returning
a boolean, it is returning a bit value. Use u32 for its return type so
that it can be used with either bitwise or boolean operators without any
warnings.
Fixes: 25cd5a3914 ("ARM: tegra: Add speedo-based process identification")
Link: https://github.com/ClangBuiltLinux/linux/issues/1488
Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This doesn't make any sense as a module since it is a critical device,
and it turns out of_phandle_iterator_args was not exported so the module
version doesn't build anyway.
Fixes: 6df9d38f91 ("soc: apple: Add driver for Apple PMGR power state controls")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
arm64: dts: ZynqMP SoC changes for v5.17
- cleanup and fix PM_INIT_FINALIZE
- check return value of zynqmp_pm_get_api_version()
* tag 'zynqmp-soc-for-v5.17' of https://github.com/Xilinx/linux-xlnx:
firmware: xilinx: check return value of zynqmp_pm_get_api_version()
soc: xilinx: add a to_zynqmp_pm_domain macro
soc: xilinx: use a properly named field instead of flags
soc: xilinx: cleanup debug and error messages
soc: xilinx: move PM_INIT_FINALIZE to zynqmp_pm_domains driver
Link: https://lore.kernel.org/r/48dec441-2c1f-73a0-3e6c-aa0d7be5ba26@monstr.eu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Apple SoC PMGR driver for 5.17
Adds the new PMGR driver. This includes the driver only; DT and
MAINTAINERS changes are part of the DT pull.
Minor change from v3: added `depends on PM` to the Kconfig to
fix COMPILE_TEST randconfig failures.
* tag 'asahi-soc-pmgr-5.17' of https://github.com/AsahiLinux/linux:
soc: apple: Add driver for Apple PMGR power state controls
Link: https://lore.kernel.org/r/049f4de9-51be-7be4-1f9a-a59756af88d7@marcan.st
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is seemingly required for DCP/DCPEXT, without which they refuse to
boot properly. They need to be set to minimum state 4 (clock gated).
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
At the moment, using the ARM32 multi_v7_defconfig always results in two
SoCs being exposed in sysfs. This is wrong, as far as I'm aware the
Qualcomm DragonBoard 410c does not actually make use of a i.MX SoC. :)
qcom-db410c:/sys/devices/soc0$ grep . *
family:Freescale i.MX
machine:Qualcomm Technologies, Inc. APQ 8016 SBC
revision:0.0
serial_number:0000000000000000
soc_id:Unknown
qcom-db410c:/sys/devices/soc1$ grep . *
family:Snapdragon
machine:APQ8016
...
This happens because imx_soc_device_init() registers the soc device
unconditionally, even when running on devices that do not make use of i.MX.
Arnd already reported this more than a year ago and even suggested a fix
similar to this commit, but for some reason it was never submitted.
Fix it by checking if the "__mxc_cpu_type" variable was actually
initialized by earlier platform code. On devices without i.MX it will
simply stay 0.
Cc: Peng Fan <peng.fan@nxp.com>
Fixes: d2199b3487 ("ARM: imx: use device_initcall for imx_soc_device_init")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/CAK8P3a0hxO1TmK6oOMQ70AHSWJnP_CAq57YMOutrxkSYNjFeuw@mail.gmail.com/
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PM_INIT_FINALIZE tells the PMU FW that Linux is able to handle the power
management nodes that are provided by the PMU FW. Nodes that are not
requested are shut down after this call.
Calling PM_INIT_FINALIZE from the zynqmp_power driver is wrong. The PM
node request mechanism is implemented in the zynqmp_pm_domains driver,
which must also call PM_INIT_FINALIZE.
Due to the behavior of the PMU FW, all devices must be powered up before
PM_INIT_FINALIZE is called, because otherwise the devices might
misbehave. Calling PM_INIT_FINALIZE from the sync_state device callback
ensures that all users probed successfully before the PMU FW is allowed
to power off unused domains.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lore.kernel.org/r/20210825150313.4033156-2-m.tretter@pengutronix.de
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
