The ingenic remoteproc driver requests its IRQ and then immediately
disables it.
The disable is necessary since irq_request() normally enables the IRQ. But
there is a new flag IRQF_NO_AUTOEN that when specified keeps the IRQ
disabled. Use this new flag rather than calling disable_irq().
This slightly reduce the boilerplate code and also avoids a theoretical
race condition where the IRQ could fire between irq_request() and
disable_irq().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211205111349.51213-1-lars@metafoo.de
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
The K3 J721S2 SoCs have three dual-core R5F subsystems, one in MCU voltage
domain and the other two in MAIN voltage domain. These R5F clusters are
similar to the R5F clusters in J7200 SoCs.
Compatible Info is updated to support J721S2 SoCs.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Link: https://lore.kernel.org/r/20211122122726.8532-5-hnagalla@ti.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
The K3 J721S2 SoCs have two C71x DSP subsystems in MAIN voltage domain,
and there are no C66x DSP subsystems on these SoCs. The C71x DSP subsystem
is a slighly updated version of the C71x DSP subsystem on J721e. The
C71x DSPs are 64 bit machine with fixed and floating point DSP
operations.
Extend support to the C71x DSPs with J721S2 compatible strings.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Link: https://lore.kernel.org/r/20211122122726.8532-4-hnagalla@ti.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
When CONFIG_PM_SLEEP is disabled, we get a harmless warning:
drivers/remoteproc/imx_dsp_rproc.c:1145:12: error: 'imx_dsp_resume' defined but not used [-Werror=unused-function]
1145 | static int imx_dsp_resume(struct device *dev)
| ^~~~~~~~~~~~~~
drivers/remoteproc/imx_dsp_rproc.c:1110:12: error: 'imx_dsp_suspend' defined but not used [-Werror=unused-function]
1110 | static int imx_dsp_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~
Mark these as __maybe_unused to get a clean build.
Fixes: ec0e5549f3 ("remoteproc: imx_dsp_rproc: Add remoteproc driver for DSP on i.MX")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211014075239.3714694-1-arnd@kernel.org
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Provide a basic driver to control DSP processor found on NXP i.MX8QM,
i.MX8QXP, i.MX8MP and i.MX8ULP.
Currently it is able to resolve addresses between DSP and main CPU,
start and stop the processor, suspend and resume.
The communication between DSP and main CPU is based on mailbox, there
are three mailbox channels (tx, rx, rxdb).
This driver was tested on NXP i.MX8QM, i.MX8QXP, i.MX8MP and i.MX8ULP.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1633944015-789-4-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
The MESON_AO_RPROC_SRAM_USABLE_BITS macro is used like this:
if (priv->sram_pa & ~MESON_AO_RPROC_SRAM_USABLE_BITS) {
dev_err(dev, "SRAM address contains unusable bits\n");
The problem is that "->sram_pa" is type phys_addr_t which is potentially
64 bits. That means the MESON_AO_RPROC_SRAM_USABLE_BITS macro needs to
be a 64 bit type as well to ensure that high 32 bits are cleared.
Fixes: 6cb58ea897 ("remoteproc: meson-mx-ao-arc: Add a driver for the AO ARC remote procesor")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211004105257.GA27301@kili
Amlogic Meson6, Meson8, Meson8b and Meson8m2 embed an ARC core in the
Always-On (AO) power-domain. This is typically used for waking up the
ARM cores after system suspend.
The configuration is spread across three different registers:
- AO_REMAP_REG0 which must be programmed to zero, it's actual purpose
is unknown. There is a second remap register which is not used in the
vendor kernel (which served as reference for this driver).
- AO_CPU_CNTL is used to start and stop the ARC core.
- AO_SECURE_REG0 in the SECBUS2 register area with unknown purpose.
To boot the ARC core we also need to enable it's gate clock and trigger
a reset.
The actual code for this ARC core can come from an ELF binary, for
example by building the Zephyr RTOS for an ARC EM4 core and then taking
"zephyr.elf" as firmware. This executable does not have any "rsc table"
so we are skipping rproc_elf_load_rsc_table (rproc_ops.parse_fw) and
rproc_elf_find_loaded_rsc_table (rproc_ops.find_loaded_rsc_table).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210921192557.1610709-3-martin.blumenstingl@googlemail.com
[Fixed header file order]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The power domains exposed by the AOSS QMP driver control the load state
resources linked to modem, adsp, cdsp remoteprocs. These are used to
notify the Always on Subsystem (AOSS) that a particular co-processor is
up/down. AOSS uses this information to wait for the co-processors to
suspend before starting its sleep sequence.
These co-processors enter low-power modes independent to that of the
application processor and the load state resources linked to them are
expected to remain unaltered across system suspend/resume cycles. To
achieve this behavior lets stop using the power-domains exposed by the
AOSS QMP node and replace them with generic qmp_send interface instead.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
[bjorn: Fixed up build error in q6v5_wcss_remove()]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631800770-371-5-git-send-email-sibis@codeaurora.org
There doesn't seem to be any actual build time dependency on the
RPMSG_QCOM_SMD, besides that these drivers should be a module if the smd
rpmsg code is a module. Drop the compile test dependency so that these
drivers can be used without RPMSG_QCOM_SMD being enabled. This is useful
for the qcom SoCs that are using RPMSG_QCOM_GLINK_SMEM instead of
RPMSG_QCOM_SMD and thus don't want to enable the SMD driver when it is
never used.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210823235120.1203512-2-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When a remoteproc has crashed, rproc_report_crash() is called to
handle whatever recovery is desired. This can happen at almost any
time, often triggered by an interrupt, though it can also be
initiated by a write to debugfs file remoteproc/remoteproc*/crash.
When a crash is reported, the crash handler worker is scheduled to
run (rproc_crash_handler_work()). One thing that worker does is
call rproc_trigger_recovery(), which calls rproc_stop(). That calls
the ->stop method for any remoteproc subdevices before making the
remote processor go offline.
The Q6V5 modem remoteproc driver implements an SSR subdevice that
notifies registered drivers when the modem changes operational state
(prepare, started, stop/crash, unprepared). The IPA driver
registers to receive these notifications.
With that as context, I'll now describe the problem.
There was a situation in which buggy modem firmware led to a modem
crash very soon after system (AP) resume had begun. The crash caused
a remoteproc SSR crash notification to be sent to the IPA driver.
The problem was that, although system resume had begun, it had not
yet completed, and the IPA driver was still in a suspended state.
This scenario could happen to any driver that registers for these
SSR notifications, because they are delivered without knowledge of
the (suspend) state of registered recipient drivers.
This patch offers a simple fix for this, by having the crash
handling worker function run on the system freezable workqueue.
This workqueue does not operate if user space is frozen (for
suspend). As a result, the SSR subdevice only delivers its
crash notification when the system is fully operational (i.e.,
neither suspended nor in suspend/resume transition).
Tested-by: Siddharth Gupta <sidgup@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210519234418.1196387-2-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The remoteproc driver is split between the responsibilities of getting
the SoC-internal ARM core up and running and the external RF (aka
"Iris") part configured.
In order to satisfy the regulator framework's need of a struct device *
to look up supplies this was implemented as two different drivers, using
of_platform_populate() in the remoteproc part to probe the iris part.
Unfortunately it's possible that the iris part probe defers on yet not
available regulators and an attempt to start the remoteproc will have to
be rejected, until this has been resolved. But there's no useful
mechanism of knowing when this would be.
Instead replace the of_platform_populate() and the iris probe with a
function that rolls its own struct device, with the relevant of_node
associated that is enough to acquire regulators and clocks specified in
the DT node and that may propagate the EPROBE_DEFER back to the wcnss
device's probe.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: Anibal Limon <anibal.limon@linaro.org>
Reported-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Anibal Limon <anibal.limon@linaro.org>
Link: https://lore.kernel.org/r/20210312002251.3273013-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Pull remoteproc updates from Bjorn Andersson:
"This adds support for controlling the PRU and R5F clusters on the TI
AM64x, the remote processor in i.MX7ULP, i.MX8MN/P and i.MX8ULP NXP
and the audio, compute and modem remoteprocs in the Qualcomm SC8180x
platform.
It fixes improper ordering of cdev and device creation of the
remoteproc control interface and it fixes resource leaks in the error
handling path of rproc_add() and the Qualcomm modem and wifi
remoteproc drivers.
Lastly it fixes a few build warnings and replace the dummy parameter
passed in the mailbox api of the stm32 driver to something not living
on the stack"
* tag 'rproc-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (32 commits)
remoteproc: qcom: pas: Add SC8180X adsp, cdsp and mpss
dt-bindings: remoteproc: qcom: pas: Add SC8180X adsp, cdsp and mpss
remoteproc: imx_rproc: support i.MX8ULP
dt-bindings: remoteproc: imx_rproc: support i.MX8ULP
remoteproc: stm32: fix mbox_send_message call
remoteproc: core: Cleanup device in case of failure
remoteproc: core: Fix cdev remove and rproc del
remoteproc: core: Move validate before device add
remoteproc: core: Move cdev add before device add
remoteproc: pru: Add support for various PRU cores on K3 AM64x SoCs
dt-bindings: remoteproc: pru: Update bindings for K3 AM64x SoCs
remoteproc: qcom_wcnss: Use devm_qcom_smem_state_get()
remoteproc: qcom_q6v5: Use devm_qcom_smem_state_get() to fix missing put()
soc: qcom: smem_state: Add devm_qcom_smem_state_get()
dt-bindings: remoteproc: qcom: pas: Fix indentation warnings
remoteproc: imx-rproc: Fix IMX_REMOTEPROC configuration
remoteproc: imx_rproc: support i.MX8MN/P
remoteproc: imx_rproc: support i.MX7ULP
remoteproc: imx_rproc: make clk optional
remoteproc: imx_rproc: initial support for mutilple start/stop method
...
Pull driver core changes from Greg KH:
"Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues"
* tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
docs: ABI: testing: sysfs-firmware-memmap: add some memmap types.
devres: Enable trace events
devres: No need to call remove_nodes() when there none present
devres: Use list_for_each_safe_from() in remove_nodes()
devres: Make locking straight forward in release_nodes()
kernfs: move revalidate to be near lookup
drivers/base: Constify static attribute_group structs
firmware_loader: remove unneeded 'comma' macro
devcoredump: remove contact information
driver core: Drop helper devm_platform_ioremap_resource_wc()
component: Rename 'dev' to 'parent'
component: Drop 'dev' argument to component_match_realloc()
device property: Don't check for NULL twice in the loops
driver core: auxiliary bus: Fix typo in the docs
drivers/base/node.c: make CACHE_ATTR define static DEVICE_ATTR_RO
debugfs: remove return value of debugfs_create_ulong()
debugfs: remove return value of debugfs_create_bool()
scsi: snic: debugfs: remove local storage of debugfs files
b43: don't save dentries for debugfs
b43legacy: don't save dentries for debugfs
...
i.MX8ULP is a new SoC with Ultra low power support, it has a Cortex-M33
core and two Cortex-A35 cores. We need to add new configuration because
it could not reuse the previous i.MX7/8 configuration.
i.MX8ULP M33 core is kicked by ROM, it is not under control of A35 core.
So need to mark the method is IMX_RPROC_NONE.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210622060148.18411-3-peng.fan@oss.nxp.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
mbox_send_message is called by passing a local dummy message or
a function parameter. As the message is queued, it is dereferenced.
This works because the message field is not used by the stm32 ipcc
driver, but it is not clean.
Fix by passing a constant string in all cases.
The associated comments are removed because rproc should not have to
deal with the behavior of the mailbox frame.
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20210420091922.29429-1-arnaud.pouliquen@foss.st.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When cdev_add is called after device_add has been called there is no
way for the userspace to know about the addition of a cdev as cdev_add
itself doesn't trigger a uevent notification, or for the kernel to
know about the change to devt. This results in two problems:
- mknod is never called for the cdev and hence no cdev appears on
devtmpfs.
- sysfs links to the new cdev are not established.
The cdev needs to be added and devt assigned before device_add() is
called in order for the relevant sysfs and devtmpfs entries to be
created and the uevent to be properly populated.
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1623723671-5517-2-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The K3 AM64x family of SoCs have a ICSSG IP that is similar to the
version on AM65x SR2.0 SoCs with some minor differences. The AM64x
SoCs contain two instances of this newer ICSSG IP. Each ICSSG processor
subsystem contains 2 primary PRU cores, 2 auxiliary PRU cores called
RTUs, and 2 new auxiliary cores called Transmit PRUs (Tx_PRUs).
Enhance the existing PRU remoteproc driver to support all these PRU,
RTU and Tx_PRU cores by using specific compatibles. The cores have the
same memory copying limitations as on AM65x, so reuses the custom memcpy
function within the driver's ELF loader implementation. The initial
names for the firmware images for each PRU core are retrieved from
DT nodes, and can be adjusted through sysfs if required.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210623173243.7862-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When CONFIG_IMX_REMOTEPROC is y and CONFIG_HAVE_ARM_SMCCC
is not set, compiling errors are encountered as follows:
drivers/remoteproc/imx_rproc.o: in function `imx_rproc_stop':
imx_rproc.c:(.text+0x140): undefined reference to `__arm_smccc_smc'
drivers/remoteproc/imx_rproc.o: in function `imx_rproc_detect_mode':
imx_rproc.c:(.text+0x272): undefined reference to `__arm_smccc_smc'
drivers/remoteproc/imx_rproc.o: in function `imx_rproc_start':
imx_rproc.c:(.text+0x5e0): undefined reference to `__arm_smccc_smc'
__arm_smccc_smc is defined when HAVE_ARM_SMCCC is y, so
add dependency on HAVE_ARM_SMCCC in IMX_REMOTEPROC configuration.
Fixes: 79806d32d5 ("remoteproc: imx_rproc: support i.MX8MN/P")
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20210610031530.26326-1-peng.fan@oss.nxp.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
