When set tx-buf-size as 0 by ethtool, hns3_init_tx_spare_buffer()
will return directly and priv->ring->tx_spare->len is uninitialized,
then print function access priv->ring->tx_spare->len will cause
this issue.
When set tx-buf-size as 0 by ethtool, the print function will
print 0 directly and not access priv->ring->tx_spare->len.
Fixes: 2373b35c24 ("net: hns3: add log for setting tx spare buf size")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing simulate_fw_crash operation periodically with a short interval
time such as 10 seconds, it is easy happened WMI command timed out for
WMI_SCAN_CHAN_LIST_CMDID in ath11k_reg_update_chan_list().
log:
[42287.610053] ath11k_pci 0000:01:00.0: wmi command 12291 timeout
[42287.610064] ath11k_pci 0000:01:00.0: failed to send WMI_SCAN_CHAN_LIST cmd
[42287.610073] ath11k_pci 0000:01:00.0: failed to perform regd update : -11
Note that this issue does not occur with a longer interval such as 20 seconds.
The reason the issue occurs with a shorter interval is the following steps:
1) Upon initial boot, or after device recovery, the initial hw scan plus
the 11d scan will run, and when 6 GHz support is present, these scans
can take up to 12 seconds to complete, so ath11k_reg_update_chan_list()
is still waiting the completion of ar->completed_11d_scan.
2) If a simulate_fw_crash operation is received during this time, those
scans do not complete, and ath11k_core_pre_reconfigure_recovery()
complete the ar->completed_11d_scan, then ath11k_reg_update_chan_list()
wakeup and start to send WMI_SCAN_CHAN_LIST_CMDID, but firmware is crashed
at this moment, so wmi timed out occur.
To address this issue, reset the 11d state during device recovery so that
WMI_SCAN_CHAN_LIST_CMDID does not timed out for short interval time such
as 10 seconds.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 1f682dc9fb ("ath11k: reduce the wait time of 11d scan and hw scan while add interface")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220505034636.29582-1-quic_wgong@quicinc.com
update LAN88xx phy ID and phy ID mask because the existing code conflicts with the LAN8742 phy.
The current phy IDs on the available hardware.
LAN8742 0x0007C130, 0x0007C131
LAN88xx 0x0007C132
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DP83TD510E is an ultra-low power Ethernet physical layer transceiver
that supports 10M single pair cable.
This driver was tested with NXP SJA1105, STMMAC and ASIX AX88772B USB Ethernet
controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export genphy_c45_baset1_read_status() to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since MDIO_PMA_PMD_BT1_CTRL register shows actual configuration (and
forced state configuration is equal to the state), we should show
this configuration for ethtool.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move baset1 specific part of genphy_c45_read_pma() code to
separate function to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not change default master/slave forced configuration if no changes was
requested.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move baset1 specific part of genphy_c45_pma_setup_forced() code to
separate function to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not change default master/slave autoneg configuration if no
changes was requested.
Fixes: 3da8ffd854 ("net: phy: Add 10BASE-T1L support in phy-c45")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds extack msg support to vxlan_fdb_delete and vxlan_fdb_parse.
extack is used to propagate meaningful error msgs to the user of vxlan
fdb netlink api
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the mechanism to lock/unlock the device 'deep sleep' mode.
When the PCIe link state is L1.2 or L2, the host side still can keep
the device is in D0 state from the host side point of view. At the same
time, if the device's 'deep sleep' mode is unlocked, the device will
go to 'deep sleep' while it is still in D0 state on the host side.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements suspend, resumes, freeze, thaw, poweroff, and restore
`dev_pm_ops` callbacks.
From the host point of view, the t7xx driver is one entity. But, the
device has several modules that need to be addressed in different ways
during power management (PM) flows.
The driver uses the term 'PM entities' to refer to the 2 DPMA and
2 CLDMA HW blocks that need to be managed during PM flows.
When a dev_pm_ops function is called, the PM entities list is iterated
and the matching function is called for each entry in the list.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Data Path Modem AP Interface (DPMAIF) HIF layer provides methods
for initialization, ISR, control and event handling of TX/RX flows.
DPMAIF TX
Exposes the 'dmpaif_tx_send_skb' function which can be used by the
network device to transmit packets.
The uplink data management uses a Descriptor Ring Buffer (DRB).
First DRB entry is a message type that will be followed by 1 or more
normal DRB entries. Message type DRB will hold the skb information
and each normal DRB entry holds a pointer to the skb payload.
DPMAIF RX
The downlink buffer management uses Buffer Address Table (BAT) and
Packet Information Table (PIT) rings.
The BAT ring holds the address of skb data buffer for the HW to use,
while the PIT contains metadata about a whole network packet including
a reference to the BAT entry holding the data buffer address.
The driver reads the PIT and BAT entries written by the modem, when
reaching a threshold, the driver will reload the PIT and BAT rings.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Control Port implements driver control messages such as modem-host
handshaking, controls port enumeration, and handles exception messages.
The handshaking process between the driver and the modem happens during
the init sequence. The process involves the exchange of a list of
supported runtime features to make sure that modem and host are ready
to provide proper feature lists including port enumeration. Further
features can be enabled and controlled in this handshaking process.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registers the t7xx device driver with the kernel. Setup all the core
components: PCIe layer, Modem Host Cross Core Interface (MHCCIF),
modem control operations, modem state machine, and build
infrastructure.
* PCIe layer code implements driver probe and removal.
* MHCCIF provides interrupt channels to communicate events
such as handshake, PM and port enumeration.
* Modem control implements the entry point for modem init,
reset and exit.
* The modem status monitor is a state machine used by modem control
to complete initialization and stop. It is used also to propagate
exception events reported by other components.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross Layer DMA (CLDMA) Hardware interface (HIF) enables the control
path of Host-Modem data transfers. CLDMA HIF layer provides a common
interface to the Port Layer.
CLDMA manages 8 independent RX/TX physical channels with data flow
control in HW queues. CLDMA uses ring buffers of General Packet
Descriptors (GPD) for TX/RX. GPDs can represent multiple or single
data buffers (DB).
CLDMA HIF initializes GPD rings, registers ISR handlers for CLDMA
interrupts, and initializes CLDMA HW registers.
CLDMA TX flow:
1. Port Layer write
2. Get DB address
3. Configure GPD
4. Triggering processing via HW register write
CLDMA RX flow:
1. CLDMA HW sends a RX "done" to host
2. Driver starts thread to safely read GPD
3. DB is sent to Port layer
4. Create a new buffer for GPD ring
Note: This patch does not enable compilation since it has dependencies
such as t7xx_pcie_mac_clear_int()/t7xx_pcie_mac_set_int() and
struct t7xx_pci_dev which are added by the core patch.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It fixes memory leak in ring buffer change logic.
When ring buffer size is changed(ethtool -G eth0 rx 4096), sfc driver
works like below.
1. stop all channels and remove ring buffers.
2. allocates new buffer array.
3. allocates rx buffers.
4. start channels.
While the above steps are working, it skips some steps if the channel
doesn't have a ->copy callback function.
Due to ptp channel doesn't have ->copy callback, these above steps are
skipped for ptp channel.
It eventually makes some problems.
a. ptp channel's ring buffer size is not changed, it works only
1024(default).
b. memory leak.
The reason for memory leak is to use the wrong ring buffer values.
There are some values, which is related to ring buffer size.
a. efx->rxq_entries
- This is global value of rx queue size.
b. rx_queue->ptr_mask
- used for access ring buffer as circular ring.
- roundup_pow_of_two(efx->rxq_entries) - 1
c. rx_queue->max_fill
- efx->rxq_entries - EFX_RXD_HEAD_ROOM
These all values should be based on ring buffer size consistently.
But ptp channel's values are not.
a. efx->rxq_entries
- This is global(for sfc) value, always new ring buffer size.
b. rx_queue->ptr_mask
- This is always 1023(default).
c. rx_queue->max_fill
- This is new ring buffer size - EFX_RXD_HEAD_ROOM.
Let's assume we set 4096 for rx ring buffer,
normal channel ptp channel
efx->rxq_entries 4096 4096
rx_queue->ptr_mask 4095 1023
rx_queue->max_fill 4086 4086
sfc driver allocates rx ring buffers based on these values.
When it allocates ptp channel's ring buffer, 4086 ring buffers are
allocated then, these buffers are attached to the allocated array.
But ptp channel's ring buffer array size is still 1024(default)
and ptr_mask is still 1023 too.
So, 3062 ring buffers will be overwritten to the array.
This is the reason for memory leak.
Test commands:
ethtool -G <interface name> rx 4096
while :
do
ip link set <interface name> up
ip link set <interface name> down
done
In order to avoid this problem, it adds ->copy callback to ptp channel
type.
So that rx_queue->ptr_mask value will be updated correctly.
Fixes: 7c236c43b8 ("sfc: Add support for IEEE-1588 PTP")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For notifications that the router needs to handle, router lock is taken.
Further, at least to determine whether an event is related to a tunnel
underlay, router lock also needs to be taken. Due to this, the router lock
is always taken for each unhandled event, and also for some handled events,
even if they are not related to underlay. Thus each event implies at least
one router lock, sometimes two.
Instead of deferring the locking to the leaf handlers, take the lock in the
router notifier handler always. This simplifies thinking about the locking
state, and in some cases saves one lock cycle.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The position of netdevice notifier registration no longer depends on the
router initialization, because the event handler no longer dispatches to
the router code. Update the comment at the registration to that effect.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The events related to IPIP tunnels are handled by the router code. Move the
handling from the central dispatcher in spectrum.c to the new notifier
handler in the router module.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The events NETDEV_PRE_CHANGEADDR, NETDEV_CHANGEADDR and NETDEV_CHANGEMTU
have implications for in-ASIC router interface objects, and as such are
handled in the router module. Move the handling from the central dispatcher
in spectrum.c to the new notifier handler in the router module.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L3 HW stats are implemented in mlxsw as RIF counters, and therefore the
code resides in spectrum_router. Exclude the offload xstats events from the
mlxsw_sp_netdevice_event_is_router() predicate, and instead recreate the
glue code in the router module.
Previously, the order of dispatch was that for events on tunnels, a
dedicated handler was called, which however did not handle HW stats events.
But there is nothing special about tunnel devices as far as HW stats: there
is a RIF associated with the tunnel netdevice, and that RIF is where the
counter should be installed. Therefore now, HW stats events are tested
first, independent of netdevice type. The upshot is that as of this commit,
mlxsw supports L3 HW stats work on GRE tunnels.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Events involving VRF, as L3 concern, are handled in the router code, by the
helper mlxsw_sp_netdevice_vrf_event(). The handler is currently invoked
from the centralized dispatcher in spectrum.c. Instead, move the call to
the newly-introduced router-specific notifier handler.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all netdevice events are handled in the centralized notifier
handler maintained by spectrum.c. Since a number of events are involving
router code, spectrum.c needs to dispatch them to spectrum_router.c. The
spectrum module therefore needs to know more about the router code than it
should have, and there is are several API points through which the two
modules communicate.
To simplify the notifier handlers, introduce a new notifier into the router
module.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enslaving netdevices to VRF is currently handled through an
mlxsw_sp_is_vrf_event() conditional in mlxsw_sp_netdevice_event(). In the
following patch sets, VRF enslavement will be handled purely in the router
code. Therefore make handlers of NETDEV_PRECHANGEUPPER tolerant of
enslaving to VRF, so that they do not bounce the change.
For NETDEV_CHANGEUPPER, drop the WARN_ON(1) and bounce from
mlxsw_sp_netdevice_port_vlan_event(). This is the only handler that warned
and bounces even in the CHANGEUPPER code, other handler quietly do nothing
when they encounter an unfamiliar upper.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A handful of WAN drivers use custom napi weights,
switch them to the new API.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8152 uses a custom napi weight, switch to the new
API for setting custom weight.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch all Ethernet drivers which use custom napi weights
to the new API.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
caif_virtio uses a custom napi weight, switch to the new
API for setting custom weights.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The felix driver is the only user of dsa_port_walk_mdbs(), and there
isn't even a good reason for it, considering that the host MDB entries
are already saved by the ocelot switch lib in the ocelot->multicast list.
Rewrite the multicast entry migration procedure around the
ocelot->multicast list so we can delete dsa_port_walk_mdbs().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I just realized we don't need to migrate the host-filtered FDB entries
when the tagging protocol changes from "ocelot" to "ocelot-8021q".
Host-filtered addresses are learned towards the PGID_CPU "multicast"
port group, reserved by software, which contains BIT(ocelot->num_phys_ports).
That is the "special" port entry in the analyzer block for the CPU port
module.
In "ocelot" mode, the CPU port module's packets are redirected to the
NPI port.
In "ocelot-8021q" mode, felix_8021q_cpu_port_init() does something funny
anyway, and changes PGID_CPU to stop pointing at the CPU port module and
start pointing at the physical port where the DSA master is attached.
The fact that we can alter the destination of packets learned towards
PGID_CPU without altering the MAC table entries themselves means that it
is pointless to walk through the FDB entries, forget that they were
learned towards PGID_CPU, and re-learn them towards the "unicast" PGID
associated with the physical port connected to the DSA master. We can
let the PGID_CPU value change simply alter the destination of the
host-filtered unicast packets in one fell swoop.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ocelot_fdb_add() redirects FDB entries installed on the NPI port towards
the special reserved PGID_CPU used for host-filtered addresses. PGID_CPU
contains BIT(ocelot->num_phys_ports) in the destination port mask, which
is code name for the CPU port module.
Whereas felix_migrate_fdbs_to_*_port() uses the ocelot->num_phys_ports
PGID directly, and it appears that this works too. Even if this PGID is
set to zero, apparently its number is special and packets still reach
the CPU port module.
Nonetheless, in the end, these addresses end up in the same place
regardless of whether they go through an extra indirection layer or not.
Use PGID_CPU across to have more uniformity.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch increases the polling rate used by the
mlxbf_gige driver on the MDIO bus. The previous
polling rate was every 100us, and the new rate is
every 5us. With this change the amount of time
spent waiting for the MDIO BUSY signal to de-assert
drops from ~100us to ~27us for each operation.
Signed-off-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Link: https://lore.kernel.org/r/20220505162309.20050-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using min_t(int, ...) as a potential array index implies to the compiler
that negative offsets should be allowed. This is not the case, though.
Replace "int" with "unsigned int". Fixes the following warning exposed
under future CONFIG_FORTIFY_SOURCE improvements:
In file included from include/linux/string.h:253,
from include/linux/bitmap.h:11,
from include/linux/cpumask.h:12,
from include/linux/smp.h:13,
from include/linux/lockdep.h:14,
from include/linux/rcupdate.h:29,
from include/linux/rculist.h:11,
from include/linux/pid.h:5,
from include/linux/sched.h:14,
from include/linux/delay.h:23,
from drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:35:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c: In function 't4_get_raw_vpd_params':
include/linux/fortify-string.h:46:33: warning: '__builtin_memcpy' pointer overflow between offset 29 and size [2147483648, 4294967295] [-Warray-bounds]
46 | #define __underlying_memcpy __builtin_memcpy
| ^
include/linux/fortify-string.h:388:9: note: in expansion of macro '__underlying_memcpy'
388 | __underlying_##op(p, q, __fortify_size); \
| ^~~~~~~~~~~~~
include/linux/fortify-string.h:433:26: note: in expansion of macro '__fortify_memcpy_chk'
433 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \
| ^~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2796:9: note: in expansion of macro 'memcpy'
2796 | memcpy(p->id, vpd + id, min_t(int, id_len, ID_LEN));
| ^~~~~~
include/linux/fortify-string.h:46:33: warning: '__builtin_memcpy' pointer overflow between offset 0 and size [2147483648, 4294967295] [-Warray-bounds]
46 | #define __underlying_memcpy __builtin_memcpy
| ^
include/linux/fortify-string.h:388:9: note: in expansion of macro '__underlying_memcpy'
388 | __underlying_##op(p, q, __fortify_size); \
| ^~~~~~~~~~~~~
include/linux/fortify-string.h:433:26: note: in expansion of macro '__fortify_memcpy_chk'
433 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \
| ^~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2798:9: note: in expansion of macro 'memcpy'
2798 | memcpy(p->sn, vpd + sn, min_t(int, sn_len, SERNUM_LEN));
| ^~~~~~
Additionally remove needless cast from u8[] to char * in last strim()
call.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202205031926.FVP7epJM-lkp@intel.com
Fixes: fc9279298e ("cxgb4: Search VPD with pci_vpd_find_ro_info_keyword()")
Fixes: 24c521f81c ("cxgb4: Use pci_vpd_find_id_string() to find VPD ID string")
Cc: Raju Rangoju <rajur@chelsio.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220505233101.1224230-1-keescook@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
10GbE Intel Wired LAN Driver Updates 2022-05-05
This series contains updates to ixgbe and igb drivers.
Jeff Daly adjusts type for 'allow_unsupported_sfp' to match the
associated struct value for ixgbe.
Alaa Mohamed converts, deprecated, kmap() call to kmap_local_page() for
igb.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igb: Convert kmap() to kmap_local_page()
ixgbe: Fix module_param allow_unsupported_sfp type
====================
Link: https://lore.kernel.org/r/20220505155651.2606195-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Read stale PTP Tx timestamps from PHY on cleanup.
After running out of Tx timestamps request handlers, hardware (HW) stops
reporting finished requests. Function ice_ptp_tx_tstamp_cleanup() used
to only clean up stale handlers in driver and was leaving the hardware
registers not read. Not reading stale PTP Tx timestamps prevents next
interrupts from arriving and makes timestamping unusable.
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The iAVF driver uses 3 virtchnl op codes to communicate with the PF
regarding the VF Tx queues:
* VIRTCHNL_OP_CONFIG_VSI_QUEUES configures the hardware and firmware
logic for the Tx queues
* VIRTCHNL_OP_ENABLE_QUEUES configures the queue interrupts
* VIRTCHNL_OP_DISABLE_QUEUES disables the queue interrupts and Tx rings.
There is a bug in the iAVF driver due to the race condition between VF
reset request and shutdown being executed in parallel. This leads to a
break in logic and VIRTCHNL_OP_DISABLE_QUEUES is not being sent.
If this occurs, the PF driver never cleans up the Tx queues. This results
in leaving behind stale Tx queue settings in the hardware and firmware.
The most obvious outcome is that upon the next
VIRTCHNL_OP_CONFIG_VSI_QUEUES, the PF will fail to program the Tx
scheduler node due to a lack of space.
We need to protect ICE driver against such situation.
To fix this, make sure we clear existing stale settings out when
handling VIRTCHNL_OP_CONFIG_VSI_QUEUES. This ensures we remove the
previous settings.
Calling ice_vf_vsi_dis_single_txq should be safe as it will do nothing if
the queue is not configured. The function already handles the case when the
Tx queue is not currently configured and exits with a 0 return in that
case.
Fixes: 7ad15440ac ("ice: Refactor VIRTCHNL_OP_CONFIG_VSI_QUEUES handling")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Function ice_plug_aux_dev() assigns pf->adev field too early prior
aux device initialization and on other side ice_unplug_aux_dev()
starts aux device deinit and at the end assigns NULL to pf->adev.
This is wrong because pf->adev should always be non-NULL only when
aux device is fully initialized and ready. This wrong order causes
a crash when ice_send_event_to_aux() call occurs because that function
depends on non-NULL value of pf->adev and does not assume that
aux device is half-initialized or half-destroyed.
After order correction the race window is tiny but it is still there,
as Leon mentioned and manipulation with pf->adev needs to be protected
by mutex.
Fix (un-)plugging functions so pf->adev field is set after aux device
init and prior aux device destroy and protect pf->adev assignment by
new mutex. This mutex is also held during ice_send_event_to_aux()
call to ensure that aux device is valid during that call.
Note that device lock used ice_send_event_to_aux() needs to be kept
to avoid race with aux drv unload.
Reproducer:
cycle=1
while :;do
echo "#### Cycle: $cycle"
ip link set ens7f0 mtu 9000
ip link add bond0 type bond mode 1 miimon 100
ip link set bond0 up
ifenslave bond0 ens7f0
ip link set bond0 mtu 9000
ethtool -L ens7f0 combined 1
ip link del bond0
ip link set ens7f0 mtu 1500
sleep 1
let cycle++
done
In short when the device is added/removed to/from bond the aux device
is unplugged/plugged. When MTU of the device is changed an event is
sent to aux device asynchronously. This can race with (un)plugging
operation and because pf->adev is set too early (plug) or too late
(unplug) the function ice_send_event_to_aux() can touch uninitialized
or destroyed fields. In the case of crash below pf->adev->dev.mutex.
Crash:
[ 53.372066] bond0: (slave ens7f0): making interface the new active one
[ 53.378622] bond0: (slave ens7f0): Enslaving as an active interface with an u
p link
[ 53.386294] IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
[ 53.549104] bond0: (slave ens7f1): Enslaving as a backup interface with an up
link
[ 54.118906] ice 0000:ca:00.0 ens7f0: Number of in use tx queues changed inval
idating tc mappings. Priority traffic classification disabled!
[ 54.233374] ice 0000:ca:00.1 ens7f1: Number of in use tx queues changed inval
idating tc mappings. Priority traffic classification disabled!
[ 54.248204] bond0: (slave ens7f0): Releasing backup interface
[ 54.253955] bond0: (slave ens7f1): making interface the new active one
[ 54.274875] bond0: (slave ens7f1): Releasing backup interface
[ 54.289153] bond0 (unregistering): Released all slaves
[ 55.383179] MII link monitoring set to 100 ms
[ 55.398696] bond0: (slave ens7f0): making interface the new active one
[ 55.405241] BUG: kernel NULL pointer dereference, address: 0000000000000080
[ 55.405289] bond0: (slave ens7f0): Enslaving as an active interface with an u
p link
[ 55.412198] #PF: supervisor write access in kernel mode
[ 55.412200] #PF: error_code(0x0002) - not-present page
[ 55.412201] PGD 25d2ad067 P4D 0
[ 55.412204] Oops: 0002 [#1] PREEMPT SMP NOPTI
[ 55.412207] CPU: 0 PID: 403 Comm: kworker/0:2 Kdump: loaded Tainted: G S
5.17.0-13579-g57f2d6540f03 #1
[ 55.429094] bond0: (slave ens7f1): Enslaving as a backup interface with an up
link
[ 55.430224] Hardware name: Dell Inc. PowerEdge R750/06V45N, BIOS 1.4.4 10/07/
2021
[ 55.430226] Workqueue: ice ice_service_task [ice]
[ 55.468169] RIP: 0010:mutex_unlock+0x10/0x20
[ 55.472439] Code: 0f b1 13 74 96 eb e0 4c 89 ee eb d8 e8 79 54 ff ff 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 65 48 8b 04 25 40 ef 01 00 31 d2 <f0> 48 0f b1 17 75 01 c3 e9 e3 fe ff ff 0f 1f 00 0f 1f 44 00 00 48
[ 55.491186] RSP: 0018:ff4454230d7d7e28 EFLAGS: 00010246
[ 55.496413] RAX: ff1a79b208b08000 RBX: ff1a79b2182e8880 RCX: 0000000000000001
[ 55.503545] RDX: 0000000000000000 RSI: ff4454230d7d7db0 RDI: 0000000000000080
[ 55.510678] RBP: ff1a79d1c7e48b68 R08: ff4454230d7d7db0 R09: 0000000000000041
[ 55.517812] R10: 00000000000000a5 R11: 00000000000006e6 R12: ff1a79d1c7e48bc0
[ 55.524945] R13: 0000000000000000 R14: ff1a79d0ffc305c0 R15: 0000000000000000
[ 55.532076] FS: 0000000000000000(0000) GS:ff1a79d0ffc00000(0000) knlGS:0000000000000000
[ 55.540163] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 55.545908] CR2: 0000000000000080 CR3: 00000003487ae003 CR4: 0000000000771ef0
[ 55.553041] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 55.560173] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 55.567305] PKRU: 55555554
[ 55.570018] Call Trace:
[ 55.572474] <TASK>
[ 55.574579] ice_service_task+0xaab/0xef0 [ice]
[ 55.579130] process_one_work+0x1c5/0x390
[ 55.583141] ? process_one_work+0x390/0x390
[ 55.587326] worker_thread+0x30/0x360
[ 55.590994] ? process_one_work+0x390/0x390
[ 55.595180] kthread+0xe6/0x110
[ 55.598325] ? kthread_complete_and_exit+0x20/0x20
[ 55.603116] ret_from_fork+0x1f/0x30
[ 55.606698] </TASK>
Fixes: f9f5301e7e ("ice: Register auxiliary device to provide RDMA")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
