mtd_read() returns -EUCLEAN in case of corrected bit-flips.
As data was read, don't error out in this case.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Leave more time to abort transmissions (which could happen at low CCK rates)
Only warn if the last filter command is stuck
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If the driver has configured the hardware to drop packets for a sta that was
in powersave mode, then clearing the flag too early opens up a small race
window during which packets could be dropped on wakeup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add SAR spec support to mt7915 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add SAR spec support to mt7603 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Typically all AP interfaces on a PHY will share the same WMM settings, while
sta/mesh interfaces will usually inherit the settings from a remote device.
In order minimize the likelihood of conflicting WMM settings, make all AP
interfaces share one slot, and all non-AP interfaces another one.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Typically all AP interfaces on a PHY will share the same WMM settings, while
sta/mesh interfaces will usually inherit the settings from a remote device.
In order minimize the likelihood of conflicting WMM settings, make all AP
interfaces share one slot, and all non-AP interfaces another one.
This also fixes running multiple AP interfaces on MT7613, which only has 3
WMM slots.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The mask variable is assigned but not used after testmode disabled:
if (!en)
mask = phy->mt76->chainmask;
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
According to the MT7921S firmware, the cmd MCU_UNI_CMD_HIF_CTRL have to
be last MCU command to execute in suspend handler and all data traffic
have to be stopped before the cmd MCU_UNI_CMD_HIF_CTRL starts as well
in order that mt7921 can successfully fall into the deep sleep mode.
Where we reuse the flag MT76_STATE_SUSPEND and avoid creating
another global flag to stop all of the traffic onto the SDIO bus.
Fixes: 48fab5bbef ("mt76: mt7921: introduce mt7921s support")
Reported-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch for the following patch
("mt76: mt7921s: fix the device cannot sleep deeply in suspend).
mt76_connac_mcu_set_hif_suspend eventually would be handled in each
bus-level suspend/resume handler in either mt7921/sdio.c or mt7921/pci.c
depending on what type of the bus the device is running on. We can move
mt76_connac_mcu_set_hif_suspend to bus-related files to simplify the logic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With 4-address mode VLAN frames, an internal header translation step fails,
leaving behind an extra 2-byte length field that must be reomved by the driver.
Add a check for this condition to fix receiving such packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With 4-address mode VLAN frames, an internal header translation step fails,
leaving behind an extra 2-byte length field that must be reomved by the driver.
Add a check for this condition to fix receiving such packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add SAR spec support to mt76x02 driver to allow configuring SAR power
limitations on the frequency ranges from the userland.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_get_sar_power and mt76_init_sar_power in the common code.
This is a preliminary patch to add sar support to mt76x02 drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check return code from mt76_connac_mcu_set_rate_txpower() in mt7921_config
routine.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
the wiphy's available antennas may be incorrect
When ext phy's antenna_mask is different from main phy
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MAC80211 doesn't care any decryption error in 802.3 path, so received
frame will be dropped if HW tell us that the cipher configuration is not
matched as well as the header has been translated to 802.3. This case only
appears when IEEE80211_FCTL_PROTECTED is 0 and cipher suit is not none in
the corresponding HW entry.
The received frame is only reported to monitor interface if HW decryption
block tell us there is ICV error or CCMP/BIP/WPI MIC error. Note in this
case the reported frame is decrypted 802.11 frame and the payload may be
malformed due to mismatched key.
Signed-off-by: Xing Song <xing.song@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get rid of PHY_MODE_AX_6G configuration in mt76_connac_get_phy_mode
routine since mode is an u8 and PHY_MODE_AX_6G is set in phymode_ext
field in mt76_connac_bss_basic_tlv.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove always false if condition in get_omac_idx for sta type
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Even if it is not a real bug since mt76_connac_get_phy_mode runs just
for mt7921 where only STA is supported, fix a theoretical NULL pointer
dereference if new added modes do not support HE
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix a possible NULL pointer deference issue in mt7921_mac_write_txwi
routine if vif is NULL.
Fixes: 33920b2bf0 ("mt76: add support for setting mcast rate")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Cap max offset value to ARRAY_SIZE(mt76_rates) - 1 in
mt76_calculate_default_rate routine in order to avoid possible Out Of
Bound accesses.
Fixes: 33920b2bf0 ("mt76: add support for setting mcast rate")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce the basic configuration for BW160 capability in 7922
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix number of rx-queued frames reported by mt76_usb driver.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 2d8be76c16 ("mt76: debugfs: improve queue node readability")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support to set SA/DA/BSSID in testmode.
During mass production stage, some test scripts or test equipments need
to set fixed addresses to detect or parse if a test is passed.
Also, MAC setting is necessary for some tx/rx tests with rx filter,
to make sure rx site only receives expected packets.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Load the default eeprom data when the content of flash/efuse is invalid.
This could help to eliminate some issues due to incorrect or
insufficient rf values.
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Only set RX_FLAG_RADIOTAP_HE and RX_FLAG_RADIOTAP_HE_MU from with their
own decoder functions to prevent header calculation error.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The HW can apply header translation to first fragmented frame, and
ramaining fragmented frame can only keep 802.11 format. Check and
reverse the first fragmented frame to 802.11 format to make sure
them can be defragmented by mac80211.
Signed-off-by: Xing Song <xing.song@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the issue that some registers not configured properly after
restarting testmode.
(e.g. change state from idle to off, and off to idle)
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is a missing mt7921e_driver_own in the MT7921E reset procedure
since the mt7921 mcu.c has been refactored for MT7921S, that will
result in MT7921E reset failure, so add it back now.
Fixes: dfc7743de1 ("mt76: mt7921: refactor mcu.c to be bus independent")
Reported-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ieee80211_register_hw() is called with rtnl_lock held, and this could be
caused lockdep from a work item that's on a workqueue that is flushed
with the rtnl held.
Move mt7615_register_ext_phy() outside the init_work().
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
offload_flags have to be dropped for mt7921 because mt76.omac_idx 0 would
always run as station mode that would cause Tx encapsulation setting
is not applied to mac80211.
Also, drop IEEE80211_OFFLOAD_ENCAP_4ADDR too because it is not really
being supported.
Fixes: e0f9fdda81 ("mt76: mt7921: add ieee80211_ops")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warning removing mt7915_mcu_set_fixed_rate
since it is no longer used:
warning: symbol 'mt7915_mcu_set_fixed_rate' was not declared.
Should it be static?
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Second set of patches for v5.17, planning to do at least one more.
Smaller new features, nothing special this time.
Major changes:
rtw88
* debugfs file to fix tx rate
iwlwifi
* support SAR GEO Offset Mapping (SGOM) via BIOS
* support firmware API version 68
* add some new device IDs
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
* tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (129 commits)
wcn36xx: Implement beacon filtering
wcn36xx: Fix physical location of beacon filter comment
wcn36xx: Fix beacon filter structure definitions
ath11k: Use reserved host DDR addresses from DT for PCI devices
dt: bindings: add new DT entry for ath11k PCI device support
wilc1000: Improve WILC TX performance when power_save is off
wl1251: specify max. IE length
rsi: fix array out of bound
wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"
wilc1000: Rename tx task from "K_TXQ_TASK" to NETDEV-tx
wilc1000: Rename irq handler from "WILC_IRQ" to netdev name
wilc1000: Rename SPI driver from "WILC_SPI" to "wilc1000_spi"
wilc1000: Fix spurious "FW not responding" error
wilc1000: Remove misleading USE_SPI_DMA macro
wilc1000: Fix missing newline in error message
wilc1000: Fix copy-and-paste typo in wilc_set_mac_address
rtw89: coex: Update COEX to 5.5.8
rtw89: coex: Cancel PS leaving while C2H comes
rtw89: coex: Update BT counters while receiving report
rtw89: coex: Define LPS state for BTC using
...
====================
Link: https://lore.kernel.org/r/20211217130952.34887C36AE9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from mac80211, wifi, bpf.
Relatively large batches of fixes from BPF and the WiFi stack, calm in
general networking.
Current release - regressions:
- dpaa2-eth: fix buffer overrun when reporting ethtool statistics
Current release - new code bugs:
- bpf: fix incorrect state pruning for <8B spill/fill
- iavf:
- add missing unlocks in iavf_watchdog_task()
- do not override the adapter state in the watchdog task (again)
- mlxsw: spectrum_router: consolidate MAC profiles when possible
Previous releases - regressions:
- mac80211 fixes:
- rate control, avoid driver crash for retransmitted frames
- regression in SSN handling of addba tx
- a memory leak where sta_info is not freed
- marking TX-during-stop for TX in in_reconfig, prevent stall
- cfg80211: acquire wiphy mutex on regulatory work
- wifi drivers: fix build regressions and LED config dependency
- virtio_net: fix rx_drops stat for small pkts
- dsa: mv88e6xxx: unforce speed & duplex in mac_link_down()
Previous releases - always broken:
- bpf fixes:
- kernel address leakage in atomic fetch
- kernel address leakage in atomic cmpxchg's r0 aux reg
- signed bounds propagation after mov32
- extable fixup offset
- extable address check
- mac80211:
- fix the size used for building probe request
- send ADDBA requests using the tid/queue of the aggregation
session
- agg-tx: don't schedule_and_wake_txq() under sta->lock, avoid
deadlocks
- validate extended element ID is present
- mptcp:
- never allow the PM to close a listener subflow (null-defer)
- clear 'kern' flag from fallback sockets, prevent crash
- fix deadlock in __mptcp_push_pending()
- inet_diag: fix kernel-infoleak for UDP sockets
- xsk: do not sleep in poll() when need_wakeup set
- smc: avoid very long waits in smc_release()
- sch_ets: don't remove idle classes from the round-robin list
- netdevsim:
- zero-initialize memory for bpf map's value, prevent info leak
- don't let user space overwrite read only (max) ethtool parms
- ixgbe: set X550 MDIO speed before talking to PHY
- stmmac:
- fix null-deref in flower deletion w/ VLAN prio Rx steering
- dwmac-rk: fix oob read in rk_gmac_setup
- ice: time stamping fixes
- systemport: add global locking for descriptor life cycle"
* tag 'net-5.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (89 commits)
bpf, selftests: Fix racing issue in btf_skc_cls_ingress test
selftest/bpf: Add a test that reads various addresses.
bpf: Fix extable address check.
bpf: Fix extable fixup offset.
bpf, selftests: Add test case trying to taint map value pointer
bpf: Make 32->64 bounds propagation slightly more robust
bpf: Fix signed bounds propagation after mov32
sit: do not call ipip6_dev_free() from sit_init_net()
net: systemport: Add global locking for descriptor lifecycle
net/smc: Prevent smc_release() from long blocking
net: Fix double 0x prefix print in SKB dump
virtio_net: fix rx_drops stat for small pkts
dsa: mv88e6xxx: fix debug print for SPEED_UNFORCED
sfc_ef100: potential dereference of null pointer
net: stmmac: dwmac-rk: fix oob read in rk_gmac_setup
net: usb: lan78xx: add Allied Telesis AT29M2-AF
net/packet: rx_owner_map depends on pg_vec
netdevsim: Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
dpaa2-eth: fix ethtool statistics
ixgbe: set X550 MDIO speed before talking to PHY
...
ath.git patches for v5.17. Major changes:
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
The prima driver facilitates the direct programming of beacon filter tables via
SMD commands.
The purpose of beacon filters is quote:
/* When beacon filtering is enabled, firmware will
* analyze the selected beacons received during BMPS,
* and monitor any changes in the IEs as listed below.
* The format of the table is:
* - EID
* - Check for IE presence
* - Byte offset
* - Byte value
* - Bit Mask
* - Byte reference
*/
The default filter table looks something like this:
tBeaconFilterIe gaBcnFilterTable[12] =
{
{ WLAN_EID_DS_PARAMS, 0u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_ERP_INFO, 0u, { 0u, 0u, 248u, 0u } },
{ WLAN_EID_EDCA_PARAM_SET, 0u, { 0u, 0u, 240u, 0u } },
{ WLAN_EID_QOS_CAPA, 0u, { 0u, 0u, 240u, 0u } },
{ WLAN_EID_CHANNEL_SWITCH, 1u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_QUIET, 1u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 1u, 0u, 248u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 2u, 0u, 235u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 5u, 0u, 253u, 0u } },
{ WLAN_EID_PWR_CONSTRAINT, 0u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_OPMODE_NOTIF, 0u, { 0u, 0u, 0u, 0u } }
};
Add in an equivalent filter set as present in the prima Linux driver.
For now omit the beacon filter "rem" command as the driver does not have an
explicit call to that SMD command. The filter mask should only count when
we are inside BMPS anyway.
Replicating the ability to program the filter table gives us scope to add and
remove elements in future. For now though this patch makes the rote-copy of the
downstream Linux beacon filter table, which we can tweak as desired from now
on.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211214134630.2214840-4-bryan.odonoghue@linaro.org
The comment in the header with respect to beacon filtering makes a
reference to "the structure above" and "the structure below" which would be
informative if the comment appeared in the right place but, it does not.
Fix the comment location so that it a least makes sense w/r/t the physical
location statements.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211214134630.2214840-3-bryan.odonoghue@linaro.org
Host DDR memory (contiguous 45 MB in mode-0 or 15 MB in mode-2)
is reserved through DT entries for firmware usage. Send the base
address from DT entries.
If DT entry is available, PCI device will work with
fixed_mem_region else host allocates multiple segments.
IPQ8074 on HK10 board supports multiple PCI devices.
IPQ8074 + QCN9074 is tested with this patch.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638789319-2950-2-git-send-email-akolli@codeaurora.org
The wakeup and sleep commands need to be sent to the WILC chip only
when it is in power save mode (PSM, as controlled by "iw dev wlan0 set
power_save on/off"). The commands are relatively costly, so it pays
to skip them when possible.
iperf3 without this patch (no significant different with PSM on/off):
TX 0.00-120.01 sec 140 MBytes 9.82 Mbits/sec
RX 0.00-120.69 sec 283 MBytes 19.6 Mbits/sec
with this patch applied:
PSM off (TX is 46% improved, RX slightly improved; may not be significant):
TX 0.00-120.00 sec 206 MBytes 14.4 Mbits/sec
RX 0.00-120.48 sec 322 MBytes 22.4 Mbits/sec
PSM on (no significant change):
TX 0.00-120.00 sec 140 MBytes 9.78 Mbits/sec
RX 0.00-120.08 sec 257 MBytes 18.0 Mbits/sec
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211210203016.3680425-2-davidm@egauge.net
This fix is similar to commit 77c91295ea ("wil6210: specify max. IE
length"). Without the max IE length set, wpa_supplicant cannot operate
using the nl80211 interface.
This patch is a workaround - the number 512 is taken from the wlcore
driver, but note that per Paul Fertser:
there's no correct number because the driver will ignore the data
passed in extra IEs.
Suggested-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211212221310.5453-1-merlijn@wizzup.org
first set of iwlwifi patches for v5.17
* A few mei fixes;
* Some improvements in D3;
* Support for new FW API commands;
* Fixes and cleanups in device configurations;
* Support some new FW API command versions;
* Fix WGDS revision 3 reading bug;
* Some firmware debugging improvements;
* Fixes for in device configuration structures;
* Improvements in the session protection code;
* Support SAR GEO Offset Mapping (SGOM) via BIOS;
* Continued work on the new Bz device family;
* Some more firmware debugging improvements;
* Support new FW API version 68;
* Add some new device IDs;
* Some other small fixes, clean-ups and improvements.
This follows normal Linux convention and is more useful since the new
name will make it apparent which network device the work-queue is for
(e.g., the name will be "wlan0-wq" for network device "wlan0").
hif_workqueue allocation has to move from
cfg80211.c:wilc_cfg80211_init() to netdev.c:wilc_netdev_ifc_init()
because the network device name is not known until after the netdev is
registered. The move also makes sense because netdev.c is already
responsible for destroying the work queue when it is no longer needed.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211209044411.3482259-5-davidm@egauge.net
