The newer chip will generate security header itself, so don't set
IEEE80211_KEY_FLAG_GENERATE_IV in this kind of chip. But, it needs to fill
key_index, PN and 802.11 header length to TX descriptor, and then hardware
uses these to generate security header.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-11-pkshih@realtek.com
The CAM, meaning address CAM and bssid CAM here, will get leaks during
SER (system error recover) L2 reset process and ieee80211_restart_hw()
which is called by L2 reset process eventually.
The normal flow would be like
-> add interface (acquire 1)
-> enter ips (release 1)
-> leave ips (acquire 1)
-> connection (occupy 1) <(A) 1 leak after L2 reset if non-sec connection>
The ieee80211_restart_hw() flow (under connection)
-> ieee80211 reconfig
-> add interface (acquire 1)
-> leave ips (acquire 1)
-> connection (occupy (A) + 2) <(B) 1 more leak>
Originally, CAM is released before HW restart only if connection is under
security. Now, release CAM whatever connection it is to fix leak in (A).
OTOH, check if CAM is already valid to avoid acquiring multiple times to
fix (B).
Besides, if AP mode, release address CAM of all stations before HW restart.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-2-pkshih@realtek.com
In AP mode, each connected station needs an entry of address CAM. The
address CAM of vif is still needed to assit in AP itself.
For station mode, it still uses vif's address CAM.
Add a help macro rtw89_get_addr_cam_of() to get addr_cam from vif or sta
for all use cases.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220207063900.43643-3-pkshih@realtek.com
With wrong rtwsta->mac_id, it can't send out ack properly when we receive
assoc response occasionally. Then, it failed to connect an AP.
The cause is that we store 'sta' and use it somewhere. To correct this,
remove the variable and use mac_id in drv_priv of 'sta' or 'vif' passed
by mac80211.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211201080607.11211-1-pkshih@realtek.com
This driver named rtw89, which is the next generation of rtw88, supports
Realtek 8852AE 802.11ax 2x2 chip whose new features are OFDMA, DBCC,
Spatial reuse, TWT and BSS coloring; now some of them aren't implemented
though.
The chip architecture is entirely different from the chips supported by
rtw88 like RTL8822CE 802.11ac chip. First of all, register address ranges
are totally redefined, so it's impossible to reuse register definition. To
communicate with firmware, new H2C/C2H format is proposed. In order to have
better utilization, TX DMA flow is changed to two stages DMA. To provide
rich RX status information, additional RX PPDU packets are added.
Since there are so many differences mentioned above, we decide to propose
a new driver. It has many authors, they are listed in alphabetic order:
Chin-Yen Lee <timlee@realtek.com>
Ping-Ke Shih <pkshih@realtek.com>
Po Hao Huang <phhuang@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Vincent Fann <vincent_fann@realtek.com>
Yan-Hsuan Chuang <tony0620emma@gmail.com>
Zong-Zhe Yang <kevin_yang@realtek.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211008035627.19463-1-pkshih@realtek.com
