This patch disables RX_TRANS_SHORT to make MDP to do header translation
when payload less than 8 bytes, hence the (QoS) null data can be encapsulated
to 802.3 format. However, WDS requires (QoS) null data in 802.11 format
to created vlan AP interfaces.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: lian.chen <lian.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Don't populate the read-only array ppet16_ppet8_ru3_ru0 on the stack but
instead make it static const. Also makes the object code a little smaller.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Soft reboot might not clear certain condition, so always call
mt7915_wfsys_reset() during init.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
By default, mt7915e does not enable thermal management until the default
thermal zone does not reach a trip point. If the rest of the system
have better cooling than the wireless hardware, then it is possible that
the wireless chip can overheat while the rest of the system is fine.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The firmware-controlled actual throttle state was previously available
by reading the cooling_device, but this confused the thermal subsystem.
Add a hwmon attribute to get it instead.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7915e registers a cooling_device with wrong semantics:
1. cooling_device expect that higher states values should cool more, but
mt7915e did the opposite... with the exception of state == 0, which
should "disable thermal management", but does not seem to have any
effect since the previous state is kept.
The result is that when the thermal zone heats up a bit and bumps the
cooling_device state from 0 to 1 to cool a bit, the performance is
destroyed, and when going back from 1 to 0, the performance stays bad.
2. Reading the cooling_device state does not always return the last
written state, but can return the actual hardware throttle state,
which is different.
This is a problem because the mt7915 firmware actually implement the
equivalent of a thermal zone with trip points. Setting the cooling
device state actually changes the throttles at each trip point, so the
following could occur if the first issue is fixed:
- thermal subsystem set state to 100% power (state=0)
- mt7915e driver set trip throttles to [100%, 50%, 25%, 12%]
- hardware heats up and decides to switch to 50% power
- thermal subsystem see that power is 50% (state=50), decide to increase
it to 60% (state=40) because the rest of the system is cool.
- mt7915e driver set trip throttle to [60%, 30%, 15%, 7%]
- hardware thus switches to 30% power
[race to the bottom continues...]
This patch corrects the semantics of the cooling_device to the one that
the thermal subsystem expect it.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Client mode on DFS channels was broken, because the old code was activating
the DFS detector on radar channels while leaving it in CAC state.
This was caused by making the decision based on the channel radar flag,
instead of hw->conf.radar_enabled.
In order to properly deal with the various corner cases, rip out the state
handling code and replace it with something that's much easier to reason
about.
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7915_mcu_rdd_background_enable and
mt7915_mcu_background_chain_ctrl routines to configure rx dfs dedicated chain.
This is a preliminary patch to add zero-wait dfs support performing CAC
detection on rdd2.
Tested-by: Owen Peng <owen.peng@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The RXQ of mt7916 are separated to MT_RXQ_MAIN_WA and MT_RXQ_MCU_WA,
so, add initialization and preftech setting for the queue MT_RXQ_MAIN_WA.
This is an intermediate patch to add mt7916 support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update max rx len of some hw modules, which aligns out vendor SDK.
In normal modes, we exchange MPDU 7991 cap with peers; however, this
won't play a part in sniffer mode.
To prevent packets which exceed the max MPDU size from entering specific
rx path in hw, we need to set a proper limit to filter them out.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix missing HE phy cap related to vif and starec setting.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable HE UL MU-MIMO in sta_rec_muru, which works on both ap and station
mode.
For sending trigger frames, one of the conditions fw uses is to check if
mib rx airtime meets the threshold.
There's a main control of mib rx airtime report register in fw, so we
need to enable the register by mcu cmd instead of directly writing it,
otherwise it will still be disabled by fw.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce a dedicated mt76 debugfs sub-dir for ext-phy in dbdc mode.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce individual TWT support to mt7915 in AP mode.
Implement the two following mac80211 callbacks:
- add_twt_setup
- twt_teardown_request
Tested-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Without this change, garbage is seen in the hwmon name and sensors output
for mt7915 is garbled. It appears that the hwmon logic does not make a
copy of the incoming string, but instead just copies a char* and expects
it to never go away.
Fixes: 33fe9c639c ("mt76: mt7915: add thermal sensor device support")
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The user is allowed to change beacon tx rate (HT/VHT/HE) from hostapd.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mcu APIs to configure bss coloring and to report bss coloring
collisions. Add support to report coloring countdown in beacon sent by
the device.
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize brightness_set and blink_set callbacks to enable LED support.
The base 0x7c000000 is MCU space so driver can't touch it, and should
map the LED base to 0x18000000 host's view.
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Money Wang <money.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
At 160, this chip can only do 2x2 NSS. Fix the features
accordingly, verified it shows up properly in iw phy foo info
now.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With this patch, users can set the trigger/restore temperature for
thermal service according to their use cases.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Report tx rate from tx status packets instead of receving periodic mcu
event. This improves flexibility, accuracy and AQL performance, and
simplifies code flow for better readability.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Disable TWT REQ/RES mac capabilities since TWT is not supported
yet in mt7915/mt7921.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The value of station mode is always 0.
Fixed: 00b2e16e00 ("mt76: mt7915: add TxBF capabilities")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt7915_mcu_set_txbf() to reduce global functions. This can be
easily extended to support other TxBF commands in further patches.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Firmware functions (SCS, MU ...) also require read-clear phy counters,
hence firmware prepares a global task to read shared fields out to a
shared pool to avoid concurrency. Switch to event format accordingly.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by adjusting Tx period by given percentage of time. The thermal
device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder
To set duty cycle as 80%,
echo 80 > /sys/class/ieee80211/phy*/cooling_device/cur_state
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This provides userspace with a unified interface, hwmon sysfs, to monitor
temperature in the hardware and can be adapted to system monitoring tools.
For reading temperature, cat /sys/class/ieee80211/phy*/hwmon*/temp1_input
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_rates array in mt76 module and remove duplicated code since it
is shared by all drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to remove duplicated code, move mt76_token_init in
mt76_alloc_device routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
