Currently 6G specific tlvs have duplicate entries which is causing
scan failures. Fix this by removing the duplicate entries of the same
tlv. This also fixes out-of-bound memory writes caused due to
adding tlvs when num_hint_bssid and num_hint_s_ssid are ZEROs.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Fixes: 74601ecfef ("ath11k: Add support for 6g scan hint")
Reported-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-7-git-send-email-kvalo@codeaurora.org
There was no way to detect if the firmware crashed so add a warning. At the
moment the firmware is not restarted or anything like that, so when this
happens ath11k modules need to be reloaded.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-2-git-send-email-kvalo@codeaurora.org
HE operation IE in beacons is constructed based on userspace params,
which firmware might not be aware of. This causes firmware not to
configure TXOP duration based RTS threshold which could cause mismatch
in behaviour with respect to what is being advertised in beacons. This
patch sends HE operation IE fetched from beacon to firmware using
WMI interface for configuration.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201020183111.25458-4-pradeepc@codeaurora.org
QMI sequence fails if caldata file is not available.
It is observed that 'rmmod ath11k' fails if qmi message fails.
With this patch rmmod/insmod is working.
Logs:
Direct firmware load for IPQ8074/caldata.bin failed with error -2
Falling back to user helper
qmi failed to load CAL: IPQ8074/caldata.bin
qmi failed to load board data file:-11
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01699-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606916215-24643-1-git-send-email-akolli@codeaurora.org
I am trying to get the ath11k driver to work with VyOS and during the
build it tries to discover the firmware blobs which drivers require.
This doesn't work with ath11k because it doesn't use the MODULE_FIRMWARE
macro. This patch fixes that.
Signed-off-by: Devin Bayer <dev@doubly.so>
[kvalo@codeaurora.org: cleanup commit log, move to pci.c]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201202182705.dhkml4nb4rf2vwav@orac
Incase of hardware encryption, WMI_PEER_AUTH flag will be set by firmware
during install key. Since install key wont be done for software encryption
mode, firmware will not set this flag. Due to this, seeing traffic failure
in software encryption. Hence, avoid resetting peer auth flag if hardware
encryption disabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01421-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606369414-25211-1-git-send-email-seevalam@codeaurora.org
It was observed that the codepath for the ATH11K_SKB_HW_80211_ENCAP was
used even when the IEEE80211_TX_CTRL_HW_80211_ENCAP was not enabled for a
an skbuff. This became even more prominent when the QCAs wlan-open patchset
for ath11k [1] was applied and a sane looking fix just caused crashes when
injecting frames via a monitor interface (for example with ratechecker):
[ 86.963152] Unable to handle kernel NULL pointer dereference at virtual address 00000338
[ 86.963192] pgd = ffffffc0008f0000
[ 86.971034] [00000338] *pgd=0000000051706003, *pud=0000000051706003, *pmd=0000000051707003, *pte=00e800000b000707
[ 86.984292] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[...]
[ 87.713339] [<ffffffbffc802480>] ieee80211_tx_status_8023+0xf8/0x220 [mac80211]
[ 87.715654] [<ffffffbffc98bad4>] ath11k_dp_tx_completion_handler+0x42c/0xa10 [ath11k]
[ 87.722924] [<ffffffbffc989190>] ath11k_dp_service_srng+0x70/0x3c8 [ath11k]
[ 87.730831] [<ffffffbffca03460>] 0xffffffbffca03460
[ 87.737599] [<ffffffc00046ef58>] net_rx_action+0xf8/0x288
[ 87.742462] [<ffffffc000097554>] __do_softirq+0xfc/0x220
[ 87.748014] [<ffffffc000097900>] irq_exit+0x98/0xe8
[ 87.753396] [<ffffffc0000cf188>] __handle_domain_irq+0x90/0xb8
[ 87.757999] [<ffffffc000081ca4>] gic_handle_irq+0x6c/0xc8
[ 87.763899] Exception stack(0xffffffc00081bdc0 to 0xffffffc00081bef0)
Problem is that the state of ath11k_skb_cb->flags must be considered
unknown and could contain anything when it is not manually initialized. So
it could also contain ATH11K_SKB_HW_80211_ENCAP. And this can result in the
code to assume that the ath11k_skb_cb->vif is set - even when this is not
always the case for non ATH11K_SKB_HW_80211_ENCAP transmissions.
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
[1] https://source.codeaurora.org/quic/qsdk/oss/system/feeds/wlan-open/tree/mac80211/patches?h=NHSS.QSDK.11.4.r3
(162 patches at the moment which are often not upstreamed but essential
to get ath11k working)
Fixes: e7f33e0c52 ("ath11k: add tx hw 802.11 encapsulation offloading support")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-2-sven@narfation.org
The driver_data area of ieee80211_tx_info is used in ath11k for
ath11k_skb_cb. The first function in the TX patch which rewrites it to
ath11k_skb_cb is already ath11k_mac_op_tx. No one else in the code path
must use it for something else before it reinitializes it. Otherwise the
data has to be considered uninitialized or corrupt.
But the ieee80211_tx_info.control shares exactly the same area as
ieee80211_tx_info.driver_data and ath11k is still using it. This results in
best case in a
ath11k c000000.wifi1: no vif found for mgmt frame, flags 0x0
or (slightly worse) in a kernel oops.
Instead, the interesting data must be moved first into the ath11k_skb_cb
and ieee80211_tx_info.control must then not be used anymore.
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-1-sven@narfation.org
Set the rx_filter in ath11k_mac_config_mon_status_default(),
only when the rx_filter value exists in ath11k_debug_rx_filter().
Without this change, rx_filter gets set to 0 and peer rssi stats
aren't updating properly from firmware.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01230-QCAHKSWPL_SILICONZ-4
Fixes: ec48d28ba2 ("ath11k: Fix rx_filter flags setting for per peer rx_stats")
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605091117-11005-1-git-send-email-mkenna@codeaurora.org
STS Beamformee capability sent from firmware is overwritten as
num_tx_chains - 1.
When num_tx_chains is 2, then STS is set to invalid value 1.
Since STS is not limited by number of TX chain, not overwriting the
capability received from firmware.
Tested on: IPQ6018 WLAN.HK.2.4.0.1-00303-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramya Gnanasekar <rgnanase@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604933229-15815-1-git-send-email-rgnanase@codeaurora.org
Current ring selector logic follows round-robin scheduling,
when a process switch from one processor to another each time,
the data in the cache would have to be invalidated
and re-loaded from RAM leads to poor cache utilization.
Therefore smp_processor_id() attempt to keep processes
on the same processor via processor affinity which improves
cache utilization. Also, ring selection could be chosen round
robin when the processor_id based ring selection does not
have the resources.
Tested-on : IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00874-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604914915-12831-1-git-send-email-ppranees@codeaurora.org
There is really no point having an auto-start for channels.
This is confusing for the device drivers, some have to enable the
channels, others don't have... and waste resources (e.g. pre allocated
buffers) that may never be used.
This is really up to the MHI device(channel) driver to manage the state
of its channels.
While at it, let's also remove the auto-start option from ath11k mhi
controller.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: clubbed ath11k change]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
ath11k_peer_create() is called without its return value being checked,
meaning errors will be unhandled. Add missing check and, as the mutex is
unconditionally unlocked on leaving this function, simplify the exit
path.
Addresses-Coverity-ID: 1497531 ("Code maintainability issues")
Fixes: 701e48a43e ("ath11k: add packet log support for QCA6390")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004100218.311653-1-alex.dewar90@gmail.com
Host needs to pass at least on bssid with all 0xff to firmware in
WMI_START_SCAN_CMDID, otherwise the bssid and receiver address
in probe requeste are all ZEROs.
This also fixed some hidden AP connection issue because some AP
doesn't respond to probe request which receiver address are all
ZEROs.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201012101733.24137-1-cjhuang@codeaurora.org
Assign the correct hw_op ath11k_init_wmi_config_ipq8074 to
the hw IPQ8074. Also update the correct TWT radio count.
Incorrect TWT radio count cause TWT feature fails on radio2
because physical device count is hardcoded to 2. so set
the value dynamically.
Found this during code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Fixes: 2d4bcbed5b ("ath11k: initialize wmi config based on hw_params")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604512020-25197-1-git-send-email-periyasa@codeaurora.org
Below listed hal descriptor mask are incorrect, so modify it to correct one
- CE destination status description meta info mask is increased from
8 bits to 16 bits from the 0th bit position
- Rx Reo queue duplicate count mask is decreased from 22 bits to 16 bits
- Reo threshold status counter sum mask is increased from 24 bits to 26 bits
No functionality impact, these descriptors are currently not used in any
supported platform. But in future if someone referred these descriptor then
ended with wrong values.
Found this during code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511921-24840-1-git-send-email-periyasa@codeaurora.org
driver not able to bootup in the single radio configured board.
single phy hw mode is converted to invalid hw mode and sent to FW
through wmi init cmd. In that case driver is not receiving wmi
ready event which leads to driver bootup fail. single phy hw mode
is a valid for single radio configured board. so removed the
conversion logic.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511331-22477-1-git-send-email-periyasa@codeaurora.org
The ath11k code will try to insert wheather rader related limits when the
DFS region is set to ETSI. For this reason, it will add two more entries in
the array of reg_rules. But the 2.4.0.1 firmware is prefiltering the list
of reg rules it returns for 2.4GHz PHYs. They will then not contain the
list of 5GHz rules and thus no wheather radar band rules were inserted by
this code.
But the code didn't fix the n_reg_rules for this regulatory domain and PHY
when this happened. This resulted in a rejection by is_valid_rd because it
found rules which start and end at 0khz. This resulted in a splat like:
Invalid regulatory domain detected
------------[ cut here ]------------
WARNING: at backports-20200628-4.4.60-9a94b73e75/net/wireless/reg.c:3721
[...]
ath11k c000000.wifi1: failed to perform regd update : -22
The number of rules must therefore be saved after they were converted from
the ath11k format to the ieee80211_regdomain format and not before.
Tested with IPQ8074 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030101940.2387952-1-sven@narfation.org
The function ath11k_wmi_send_init_country_cmd is taking 3 byte from alpha2
of the structure wmi_init_country_params. But the function
ath11k_reg_notifier is only initializing 2 bytes. The third byte is
therefore always an uninitialized value.
The command can happen to look like
0c 00 87 02 01 00 00 00 00 00 00 00 43 41 f8 00
instead of
0c 00 87 02 01 00 00 00 00 00 00 00 43 41 00 00
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01161-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201021140555.4114715-1-sven@narfation.org
cold boot calibration is the process to calibrate all the channels
during the boot-up to avoid the calibration delay during the
channel change.
During the boot-up, firmware started in cold boot calibration mode
Firmware calibrate all channels and generate CalDb(DDR).
Subsequent wifi bringup will reuse the same CalDb.
Firmware is restarted in normal mode to continue the normal operation.
caldb memory address send to firmware through the QMI message.Firmware
use this address to store the caldb data and use it until next reboot.
This will give the improvement during the channel change. But it is
increasing the boot-up time(up to 15sec depend on number of radios).
So if the user want to reduce the boot-up time and accepting for channel
change delay, user can disable this feature using the module param
cold_boot_cal=0.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01162-QCAHKSWPL_SILICONZ-1
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602862111-14063-1-git-send-email-ssreeela@codeaurora.org
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on IPQ6018 using bus, qmi-chip-id and
qmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.
This problem was already solved on ath10k by adding a ",variant=.*" at the
end of the board name. The same functionality must also be provided for
ath11k.
The device tree requires an additional string to define the variant name
wifi@c000000 {
status = "okay";
qcom,ath11k-calibration-variant = "Cigtech-WF-188";
};
This would create the boarddata identifier for the board-2.bin search
* bus=ahb,qmi-chip-id=0,qmi-board-id=18,variant=Cigtech-WF-188
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-2-sven@narfation.org
This patch adds driver support for FILS discovery and unsolicited
broadcast probe response transmission features which are used for
in-band discovery in 6GHz band.
Currently this support is enabled only in 6GHz by setting hardware flags.
Changes include WMI commands to enable transmission, set packet
interval, set template, and handle events.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007204036.19780-1-alokad@codeaurora.org
