Add driver support to enable timestamping on all RX packets
that are received by the NIC. This capability can be requested
by the applications using SIOCSHWTSTAMP ioctl with filter type
HWTSTAMP_FILTER_ALL.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For correctness, we need to configure the packet filters for timestamping
during bnxt_open. This way they are always configured after firmware
reset or chip reset. We should not assume that the filters will always
be retained across resets.
This patch modifies the ioctl handler and always configures the PTP
filters in the bnxt_open() path.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom bnxt_ptp driver does not compile with GCC 11.2.2 when
CONFIG_WERROR is enabled. The following error is generated:
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c: In function ‘bnxt_ptp_enable’:
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c:400:43: error: array
subscript 255 is above array bounds of ‘struct pps_pin[4]’
[-Werror=array-bounds]
400 | ptp->pps_info.pins[pin_id].event = BNXT_PPS_EVENT_EXTERNAL;
| ~~~~~~~~~~~~~~~~~~^~~~~~~~
In file included from drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c:20:
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h:75:24: note: while
referencing ‘pins’
75 | struct pps_pin pins[BNXT_MAX_TSIO_PINS];
| ^~~~
cc1: all warnings being treated as errors
This is due to the function ptp_find_pin() returning a pin ID of -1 when
a valid pin is not found and this error never being checked.
Change the TSIO_PIN_VALID() function to also check that a pin ID is not
negative and use this macro in bnxt_ptp_enable() to check the result of
the calls to ptp_find_pin() to return an error early for invalid pins.
This fixes the compilation error.
Cc: <stable@vger.kernel.org>
Fixes: 9e518f2580 ("bnxt_en: 1PPS functions to configure TSIO pins")
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220328062708.207079-1-damien.lemoal@opensource.wdc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for RTC mode if it is supported by firmware. In RTC
mode, the PHC is set to the 64-bit clock. Because the legacy interface
is 48-bit, the driver still has to keep track of the upper 16 bits and
handle the rollover.
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTNL lock must be held between down and up to prevent interleaving
state changes, especially since external state changes might release
and allocate different driver resource subsets that would otherwise
need to be tracked and carefully handled. If the down function fails,
then devlink will not call the corresponding up function, thus the
lock is released in the down error paths.
v2: Don't use devlink_reload_disable() and devlink_reload_enable().
Instead, check that the netdev is not in unregistered state before
proceeding with reload.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-Off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion follows this general pattern for most of the calls:
1. The input message is changed from a stack variable initialized
using bnxt_hwrm_cmd_hdr_init() to a pointer allocated and intialized
using hwrm_req_init().
2. If we don't need to read the firmware response, the hwrm_send_message()
call is replaced with hwrm_req_send().
3. If we need to read the firmware response, the mutex lock is replaced
by hwrm_req_hold() to hold the response. When the response is read, the
mutex unlock is replaced by hwrm_req_drop().
If additional DMA buffers are needed for firmware response data, the
hwrm_req_dma_slice() is used instead of calling dma_alloc_coherent().
Some minor refactoring is also done while doing these conversions.
v2: Fix unintialized variable warnings in __bnxt_hwrm_get_tx_rings()
and bnxt_approve_mac()
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all firmware messaging functions and definitions to new
bnxt_hwrm.[ch]. The follow-on patches will make major modifications
to these APIs.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware interface requires the PTP sequence ID header offset to
be passed to the firmware to properly find the matching timestamp
for all protocols.
Fixes: 83bb623c96 ("bnxt_en: Transmit and retrieve packet timestamps")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once the PPS pins are configured, the FW can report
PPS values using ASYNC event. This patch adds the
ASYNC event handler and subsequent reporting of the
events to kernel.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Application will send ioctls to set/clear PPS pin functions
based on user input. This patch implements the driver
callbacks that will configure the TSIO pins using firmware
commands. After firmware reset, the TSIO pins will be reconfigured
again.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1PPS (One Pulse Per Second) is a signal generated either
by the NIC PHC or an external timing source.
Integrating the support to configure and use 1PPS using
the TSIO pins along with PTP timestamps will add Grand
Master capability to the 5750X family chipsets.
This patch initializes the driver data structures and
registers the 1PPS with kernel, based on the TSIO pins'
capability in the hardware. This will create a /dev/ppsX
device which applications can use to receive PPS events.
Later patches will define functions to configure and use
the pins.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During error recovery or hot firmware upgrade, the chip may be under
reset and the PHC register read cycles may cause completion timeouts.
Check that the chip is not under reset condition before proceeding
to read the PHC by checking the flag BNXT_STATE_IN_FW_RESET. We also
need to take the ptp_lock before we set this flag to prevent race
conditions.
We need this logic because the PHC now will stay registered after
bnxt_close().
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out by Richard Cochran that registering the PHC during
probe is better than during ifup, so move bnxt_ptp_init() back to
bnxt_init_one(). In order to work correctly after firmware reset which
may result in PTP config. changes, we modify bnxt_ptp_init() to return
if the PHC has been registered earlier. If PTP is no longer supported
by the new firmware, we will unregister the PHC and clean up.
This partially reverts:
d7859afb68 ("bnxt_en: Move bnxt_ptp_init() to bnxt_open()")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use the timecounter APIs for the 48-bit PHC and packet timestamps.
We must periodically update the timecounter at roughly half the
overflow interval. The overflow interval is about 78 hours, so
update it every 19 hours (1/4 interval) for some extra margins.
Fixes: 390862f45c ("bnxt_en: Get the full 48-bit hardware timestamp periodically")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device needs to be in ifup state for PTP to function, so move
bnxt_ptp_init() to bnxt_open(). This means that the PHC will be
registered during bnxt_open().
This also makes firmware reset work correctly. PTP configurations
may change after firmware upgrade or downgrade. bnxt_open() will
be called after firmware reset, so it will work properly.
bnxt_ptp_start() is now incorporated into bnxt_ptp_init(). We now
also need to call bnxt_ptp_clear() in bnxt_close().
Fixes: 93cb62d98e ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup the TXBD to enable TX timestamp if requested. At TX packet DMA
completion, if we requested TX timestamp on that packet, we defer to
.do_aux_work() to obtain the TX timestamp from the firmware before we
free the TX SKB.
v2: Use .do_aux_work() to get the TX timestamp from firmware.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RX packet is timestamped by the hardware, the RX completion
record will contain the lower 32-bit of the timestamp. This needs
to be combined with the upper 16-bit of the periodic timestamp that
we get from the timer. The previous snapshot in ptp->old_timer is
used to make sure that the snapshot is not ahead of the RX timestamp
and we adjust for wrap-around if needed.
v2: Make ptp->old_time read access safe on 32-bit CPUs.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From the bnxt_timer(), read the 48-bit hardware running clock
periodically and store it in ptp->current_time. The previous snapshot
of the clock will be stored in ptp->old_time. The old_time snapshot
will be used in the next patches to compute the RX packet timestamps.
v2: Use .do_aux_work() to read the timer periodically.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the clock APIs to set/get/adjust the hw clock, and the related
ioctls and ethtool methods.
v2: Propagate error code from ptp_clock_register().
Add spinlock to serialize access to the timecounter. The
timecounter is accessed in process context and the RX datapath.
Read the PHC using direct registers.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
