On some older chips, it is necessary to do a reset when we get buffer
errors associated with an RX ring. These buffer errors may become
frequent if the RX ring underruns under heavy traffic. The current
code does a global reset of all reasources when this happens. This
works but creates a big disruption of all rings when one RX ring is
having problem. This patch implements a localized RX ring reset of
just the RX ring having the issue. All other rings including all
TX rings will not be affected by this single RX ring reset.
Only the older chips prior to the P5 class supports this reset.
Because it is not a global reset, packets may still be arriving
while we are calling firmware to reset that ring. We need to be
sure that we don't post any buffers during this time while the
ring is undergoing reset. After firmware completes successfully,
the ring will be in the reset state with no buffers and we can start
filling it with new buffers and posting them.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_init_one_rx_ring() includes logic to initialize the BDs for one RX
ring and to allocate the buffers. Separate the allocation logic into a
new bnxt_alloc_one_rx_ring() function. The allocation function will be
used later to allocate new buffers for one specified RX ring when we
reset that RX ring.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_free_rx_skbs() frees all the allocated buffers and SKBs for
every RX ring. Refactor this function by calling a new function
bnxt_free_one_rx_ring_skbs() to free these buffers on one specified
RX ring at a time. This is preparation work for resetting one RX
ring during run-time.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware does not come out of reset, log FW health status info
to provide more information on firmware status.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NS3 SoC platforms require assistance from the OP-TEE to recover
firmware if a crash occurs while no driver is bound. The
CRASHED_NO_MASTER condition is recorded in the firmware status register
during the crash to indicate when driver intervension is needed to
coordinate a firmware reload. This condition is detected during early
driver initialization in order to effect a firmware fastboot on
supported platforms when necessary.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware now supports device independent discovery of the status
register location. This status register can provide more detailed
information about firmware errors, especially if problems occur
before the HWRM interface is functioning. Attempt to map this
register if it is present and report the firmware status on firmware
init failures.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocator for the firmware health structure conflates allocation
and capability checks, limiting the reusability of the code. This patch
separates out the capability check and disablement and improves the
warning message to better describe the consequences of an allocation
failure.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature allows the user to set the different FEC modes on the NIC
port. Any new setting will take effect immediately after a link toggle.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code is reporting the FEC configured settings during link up.
Change it to report the more useful active FEC encoding that may be
negotiated or auto detected.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .get_fecparam() method to report the configured and active FEC
settings. Also report the supported and advertised FEC settings to
the .get_link_ksettings() method.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some 200G dual port NICs, if one port is configured to 200G,
firmware will disable the ethernet link on the other port. Firmware
will send notification to the driver for the disabled port when this
happens. Define a new field in the link_info structure to keep track
of this state. The new phy_state field replaces the unused loop_back
field.
Log a message when the phy_state changes state. In the disabled state,
disallow any PHY configurations on the disabled port as the firmware
will fail all calls to configure the PHY in this state.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware interface has added support for new link speeds using
PAM4 modulation. Expand the bnxt_link_info structure to closely
mirror the new firmware structures. Add logic to copy the PAM4
capabilities and settings from the firmware.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the code for determining an advertised speed is no longer
supported into a separate function. This will avoid some code
duplication in a later patch when supporting PAM4 speeds, since
these speeds are specified in a separate field.
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main changes include FEC, ECN statistics, HWRM_PORT_PHY_QCFG
response size reduction, and a new counter added to
ctx_hw_stats_ext struct to support the new 58818 chip.
The ctx_hw_stats_ext structure is now the superset supporting the new
58818 chips and the prior P5 chips. Add a new flag to identify the new
chip and use constants for the chip specific ring statistics sizes
instead of the size of the structure.
Because the HWRM_PORT_PHY_QCFG response structure size has shrunk back
to 96 bytes, the workaround added earlier to limit the size of this
message for forwarding to the VF can be removed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong flag value caused the firmware call to return actual port
counters instead of the counter masks. This messed up the counter
overflow logic and caused erratic extended port counters to be
displayed under ethtool -S.
Fixes: 531d1d269c ("bnxt_en: Retrieve hardware masks for port counters.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix it to set the required fid input parameter. The firmware call
fails without this patch.
Fixes: d752d0536c ("bnxt_en: Retrieve hardware counter masks from firmware if available.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning "unknown" as a temperature value violates the hwmon interface
rules. Appropriate error codes should be returned via device_attribute
show instead. These will ultimately be propagated to the user via the
file system interface.
In addition to the corrected error handling, it is an even better idea to
not present the sensor in sysfs at all if it is known that the read will
definitely fail. Given that temp1_input is currently the only sensor
reported, ensure no hwmon registration if TEMP_MONITOR_QUERY is not
supported or if it will fail due to access permissions. Something smarter
may be needed if and when other sensors are added.
Fixes: 12cce90b93 ("bnxt_en: fix HWRM error when querying VF temperature")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using strlcpy() to copy from VPD is not correct because VPD strings
are not necessarily NULL terminated. Use memcpy() to copy the VPD
length up to the destination buffer size - 1. The destination is
zeroed memory so it will always be NULL terminated.
Fixes: a0d0fd70fe ("bnxt_en: Read partno and serialno of the board from VPD")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allow drivers to call napi_hash_del() before calling
netif_napi_del() to batch RCU grace periods. This makes
the API asymmetric and leaks internal implementation details.
Soon we will want the grace period to protect more than just
the NAPI hash table.
Restructure the API and have drivers call a new function -
__netif_napi_del() if they want to take care of RCU waits.
Note that only core was checking the return status from
napi_hash_del() so the new helper does not report if the
NAPI was actually deleted.
Some notes on driver oddness:
- veth observed the grace period before calling netif_napi_del()
but that should not matter
- myri10ge observed normal RCU flavor
- bnx2x and enic did not actually observe the grace period
(unless they did so implicitly)
- virtio_net and enic only unhashed Rx NAPIs
The last two points seem to indicate that the calls to
napi_hash_del() were a left over rather than an optimization.
Regardless, it's easy enough to correct them.
This patch may introduce extra synchronize_net() calls for
interfaces which set NAPI_STATE_NO_BUSY_POLL and depend on
free_netdev() to call netif_napi_del(). This seems inevitable
since we want to use RCU for netpoll dev->napi_list traversal,
and almost no drivers set IFF_DISABLE_NETPOLL.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_fw_reset_task() which runs from a workqueue can race with
bnxt_remove_one(). For example, if firmware reset and VF FLR are
happening at about the same time.
bnxt_remove_one() already cancels the workqueue and waits for it
to finish, but we need to do this earlier before the devlink
reporters are destroyed. This will guarantee that
the devlink reporters will always be valid when bnxt_fw_reset_task()
is still running.
Fixes: b148bb238c ("bnxt_en: Fix possible crash in bnxt_fw_reset_task().")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the driver goes through PCIe AER reset in error state, all
firmware messages will timeout because the PCIe bus is no longer
accessible. This can lead to AER reset taking many minutes to
complete as each firmware command takes time to timeout.
Define a new macro BNXT_NO_FW_ACCESS() to skip these firmware messages
when either firmware is in fatal error state or when
pci_channel_offline() is true. It now takes a more reasonable 20 to
30 seconds to complete AER recovery.
Fixes: b4fff2079d ("bnxt_en: Do not send firmware messages if firmware is in error state.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
The recent changes to support user-defined RSS map assume that RX
rings are always reserved and the default RSS map is set after the
RX rings are successfully reserved. If the firmware spec is older
than 1.6.1, no ring reservations are required and the default RSS
map is not setup at all. In another scenario where the fw Resource
Manager is older, RX rings are not reserved and we also end up with
no valid RSS map.
Fix both issues in bnxt_need_reserve_rings(). In both scenarios
described above, we don't need to reserve RX rings so we need to
call this new function bnxt_check_rss_map_no_rmgr() to setup the
default RSS map when needed.
Without valid RSS map, the NIC won't receive packets properly.
Fixes: 1667cbf6a4 ("bnxt_en: Add logical RSS indirection table structure.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no VF rings available during probe when the device is configured
using the Minimal-Static reservation strategy. In this case, the RSS
indirection table can only be initialized later, during bnxt_open_nic().
However, this was not happening because the rings will already have been
reserved via bnxt_init_dflt_ring_mode(), causing bnxt_need_reserve_rings()
to return false in bnxt_reserve_rings() and bypass the RSS table init.
Solve this by pushing the call to bnxt_set_dflt_rss_indir_tbl() into
__bnxt_reserve_rings(), which is common to both paths and is called
whenever ring configuration is changed. After doing this, the RSS table
init that must be called from bnxt_init_one() happens implicitly via
bnxt_set_default_rings(), necessitating doing the allocation earlier in
order to avoid a null pointer dereference.
Fixes: bd3191b5d8 ("bnxt_en: Implement ethtool -X to set indirection table.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware returns RESOURCE_ACCESS_DENIED for HWRM_TEMP_MONITORY_QUERY for
VFs. This produces unpleasing error messages in the log when temp1_input
is queried via the hwmon sysfs interface from a VF.
The error is harmless and expected, so silence it and return unknown as
the value. Since the device temperature is not particularly sensitive
information, provide flexibility to change this policy in future by
silencing the error rather than avoiding the HWRM call entirely for VFs.
Fixes: cde49a42a9 ("bnxt_en: Add hwmon sysfs support to read temperature")
Cc: Marc Smith <msmith626@gmail.com>
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_fw_reset_task() is run from a delayed workqueue. The current
code is not cancelling the workqueue in the driver's .remove()
method and it can potentially crash if the device is removed with
the workqueue still pending.
The fix is to clear the BNXT_STATE_IN_FW_RESET flag and then cancel
the delayed workqueue in bnxt_remove_one(). bnxt_queue_fw_reset_work()
also needs to check that this flag is set before scheduling. This
will guarantee that no rescheduling will be done after it is cancelled.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PCI error is detected the PCI state could be corrupt, save
the PCI state after initialization and restore it after the slot
reset.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes coccicheck warning:
./drivers/net/ethernet/broadcom/bnxt/bnxt.c:3730:19-37: WARNING:
dma_alloc_coherent use in stats -> hw_stats already zeroes out
memory, so memset is not needed
dma_alloc_coherent use in status already zeroes out memory,
so memset is not needed
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Li Heng <liheng40@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we can report all the full 64-bit CPU endian software accumulated
counters instead of the hw counters, some of which may be less than
64-bit wide. Define the necessary macros to access the software
counters.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the infrastructure in place, add the new function
bnxt_accumulate_all_stats() to periodically accumulate and check for
counter rollover of all ring stats and port stats.
A chip bug was also discovered that could cause some ring counters to
become 0 during DMA. Workaround by ignoring zeros on the affected
chips.
Some older frimware will reset port counters during ifdown. We need
to check for that and free the accumulated port counters during ifdown
to prevent bogus counter overflow detection during ifup.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If supported by newer firmware, make the firmware call to query all
the port counter masks. If not supported, assume 40-bit port
counter masks.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware has a new call HWRM_FUNC_QSTATS_EXT to retrieve the
masks of all ring counters. Make this call when supported to
initialize the hardware masks of all ring counters. If the call
is not available, assume 48-bit ring counter masks on P5 chips.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of these DMAed hardware counters are not full 64-bit counters and
so we need to accumulate them as they overflow. Allocate copies of these
DMA statistics memory blocks with the same size for accumulation. The
hardware counter widths are also counter specific so we allocate
memory for masks that correspond to each counter.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver manages multiple statistics structures of different sizes.
They are all allocated, freed, and handled practically the same. Define
a new bnxt_stats_mem structure and common allocation and free functions
for all staistics memory blocks.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main changes are 200G support and fixing the definitions of discard and
error counters to match the hardware definitions.
Because the HWRM_PORT_PHY_QCFG message size has now exceeded the max.
encapsulated response message size of 96 bytes from the PF to the VF,
we now need to cap this message to 96 bytes for forwarding. The forwarded
response only needs to contain the basic link status and speed information
and can be capped without adding the new information.
v2: Fix bnxt_re compile error.
Cc: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove PCIe non-counters display from ethtool statistics, as
they are not simple counters but register dump. The next few
patches will add logic to detect counter roll-over and it won't
work with these PCIe non-counters.
There will be a follow up patch to get PCIe information via
ethtool register dump.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
The fact that NETIF_F_HW_TC is not set should be a sufficient
indication to the user that TC offloads are not supported.
No need to bother users of older firmware versions with
pointless warnings on every boot.
Also, since the support is optional, bnxt_init_tc() should not
return an error in case FW is old, similarly to how error
is not returned when CONFIG_BNXT_FLOWER_OFFLOAD is not set.
With that we can add an error message to the caller, to warn
about actual unexpected failures.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current completion ring sizing formula is wrong with TPA enabled.
The formula assumes that the number of TPA completions are bound by the
RX ring size, but that's not true. TPA_START completions are immediately
recycled so they are not bound by the RX ring size. We must add
bp->max_tpa to the worst case maximum RX and TPA completions.
The completion ring can overflow because of this mistake. This will
cause hardware to disable the completion ring when this happens,
leading to RX and TX traffic to stall on that ring. This issue is
generally exposed only when the RX ring size is set very small.
Fix the formula by adding bp->max_tpa to the number of RX completions
if TPA is enabled.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.");
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a shared port PHY configuration, async event is received when any of the
port modifies the configuration. Ethtool link settings should be
initialised after updated PHY configuration from firmware.
Fixes: b1613e78e9 ("bnxt_en: Add async. event logic for PHY configuration changes.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new infra, taking advantage of sleeping in callbacks.
v2:
- use bp->*_fw_dst_port_id != INVALID_HW_RING_ID as indication
that the offload is active.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bare-metal use cases require giving firmware and the embedded
application processor control over VLAN offloads. The driver should
not attempt to override or utilize this feature in such scenarios
since it will not work as expected.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware VLAN offload feature on our NIC does not have separate
knobs for handling customer and service tags on RX. Either offloading
of both must be enabled or both must be disabled. Introduce definitions
for the combined feature set in order to clean up the code and make
this constraint more clear. Technically these features can be separately
enabled on TX, however, since the default is to turn both on, the
combined TX feature set is also introduced for code consistency.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new infrastructure in place, we can now support the setting of
the indirection table from ethtool.
When changing channels, in a rare case that firmware cannot reserve the
rings that were promised, we will still try to keep the RSS map and only
revert to default when absolutely necessary.
v4: Revert RSS map to default during ring change only when absolutely
necessary.
v3: Add warning messages when firmware cannot reserve the requested RX
rings, and when the RSS table entries have to change to default.
v2: When changing channels, if the RSS table size changes and RSS map
is non-default, return error.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
