In the error handling in c_can_power_up(), there are two bugs:
1) c_can_pm_runtime_get_sync() will increase usage counter if device is not
empty. Forgetting to call c_can_pm_runtime_put_sync() will result in a
reference leak here.
2) c_can_reset_ram() operation will set start bit when enable is true. We
should clear it in the error handling.
We fix it by adding c_can_pm_runtime_put_sync() for 1), and
c_can_reset_ram(enable is false) for 2) in the error handling.
Fixes: 8212003260 ("can: c_can: Add d_can suspend resume support")
Fixes: 52cde85acc ("can: c_can: Add d_can raminit support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201128133922.3276973-2-zhangqilong3@huawei.com
[mkl: return "0" instead of "ret"]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Losing arbitration is normal in a CAN-bus network, it means that a higher
priority frame is being send and the pending message will be retried later.
Hence most driver only increment arbitration_lost, but the sun4i driver also
incremeants tx_error, causing errors to be reported on a normal functioning
CAN-bus. So stop counting them as errors.
Fixes: 0738eff14d ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Link: https://lore.kernel.org/r/20201127095941.21609-1-jhofstee@victronenergy.com
[mkl: split into two seperate patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Losing arbitration is normal in a CAN-bus network, it means that a higher
priority frame is being send and the pending message will be retried later.
Hence most driver only increment arbitration_lost, but the sja1000 driver also
incremeants tx_error, causing errors to be reported on a normal functioning
CAN-bus. So stop counting them as errors.
Fixes: 8935f57e68 ("can: sja1000: fix network statistics update")
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Link: https://lore.kernel.org/r/20201127095941.21609-1-jhofstee@victronenergy.com
[mkl: split into two seperate patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At lest the revision 3.3.0 of the bosch m_can IP core specifies that valid
register values for "Nominal Time segment after sample point (NTSEG2)" are from
1 to 127. As the hardware uses a value of one more than the programmed value,
mean tseg2_min is 2.
This patch fixes the tseg2_min value accordingly.
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Mario Huettel <mario.huettel@gmx.net>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Link: https://lore.kernel.org/r/20201124190751.3972238-1-mkl@pengutronix.de
Fixes: b03cfc5bb0 ("can: m_can: Enable M_CAN version dependent initialization")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The threaded IRQ handler is used for the tcan4x5x driver only. The IRQ pin of
the tcan4x5x controller is active low, so better not use IRQF_TRIGGER_FALLING
when requesting the IRQ. As this can result in missing interrupts.
Further, if the device tree specified the interrupt as "IRQ_TYPE_LEVEL_LOW",
unloading and reloading of the driver results in the following error during
ifup:
| irq: type mismatch, failed to map hwirq-31 for gpio@20a8000!
| tcan4x5x spi1.1: m_can device registered (irq=0, version=32)
| tcan4x5x spi1.1 can2: TCAN4X5X successfully initialized.
| tcan4x5x spi1.1 can2: failed to request interrupt
This patch fixes the problem by removing the IRQF_TRIGGER_FALLING from the
request_threaded_irq().
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Cc: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/20201127093548.509253-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch add a check to the mcp251xfd_probe() function to bail out and give
the user a proper error message if no IRQ is specified. Otherwise the driver
will probe just fine but ifup will fail with a meaningless "RTNETLINK answers:
Invalid argument" error message.
Link: https://lore.kernel.org/r/20201123113522.3820052-1-mkl@pengutronix.de
Reported-by: Niels Petter <petter@ka-long.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The firmware on the original USB2CAN by Geschwister Schneider Technologie
Entwicklungs- und Vertriebs UG exchanges all data between the host and the
device in host byte order. This is done with the struct
gs_host_config::byte_order member, which is sent first to indicate the desired
byte order.
The widely used open source firmware candleLight doesn't support this feature
and exchanges the data in little endian byte order. This breaks if a device
with candleLight firmware is used on big endianess systems.
To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which
is a transparent cookie) are converted to __le32.
Cc: Maximilian Schneider <max@schneidersoft.net>
Cc: Hubert Denkmair <hubert@denkmair.de>
Reported-by: Michael Rausch <mr@netadair.de>
Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There haven been reports, that the flexcan_close() soradically hangs during
simultanious ifdown, sending of CAN messages and probably open CAN bus:
| (__schedule) from [<808bbd34>] (schedule+0x90/0xb8)
| (schedule) from [<808bf274>] (schedule_timeout+0x1f8/0x24c)
| (schedule_timeout) from [<8016be44>] (msleep+0x18/0x1c)
| (msleep) from [<80746a64>] (napi_disable+0x60/0x70)
| (napi_disable) from [<8052fdd0>] (flexcan_close+0x2c/0x140)
| (flexcan_close) from [<80744930>] (__dev_close_many+0xb8/0xd8)
| (__dev_close_many) from [<8074db9c>] (__dev_change_flags+0xd0/0x1a0)
| (__dev_change_flags) from [<8074dc84>] (dev_change_flags+0x18/0x48)
| (dev_change_flags) from [<80760c24>] (do_setlink+0x44c/0x7b4)
| (do_setlink) from [<80761560>] (rtnl_newlink+0x374/0x68c)
I was unable to reproduce the issue, but a cleanup of the flexcan close
sequence has probably fixed the problem at the reporting user.
This patch changes the sequence in flexcan_close() to:
- stop the TX queue
- disable the interrupts on the chip level and wait via free_irq()
synchronously for the interrupt handler to finish
- disable RX offload, which disables synchronously NAPI
- disable the flexcan on the chip level
- free RX offload
- disable the transceiver
- close the CAN device
- disable the clocks
Link: https://lore.kernel.org/r/20201119100917.3013281-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function flexcan_chip_start() first configures the CAN controller and then
enables the interrupt, flexcan_chip_stop() does the opposite.
In an upcoming patch the order of operations in flexcan_open() and
flexcan_close() are changed. This requires
flexcan_chip_start()/flexcan_chip_stop_disable_on_error() and
flexcan_chip_interrupts_{enable,disable}() to be independent of each other.
This patch moves the enabling of the interrupts from flexcan_chip_start() to
its callers flexcan_open() and flexcan_resume(). Likewise the disabling of the
interrupts is moved from __flexcan_chip_stop() to its indirect callers
flexcan_close() and flexcan_suspend().
Link: https://lore.kernel.org/r/20201119100917.3013281-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The helper functions can_len2dlc and can_dlc2len are only relevant for
CAN FD data length code (DLC) conversion.
To fit the introduced can_cc_dlc2len for Classical CAN we rename:
can_dlc2len -> can_fd_dlc2len to get the payload length from the DLC
can_len2dlc -> can_fd_len2dlc to get the DLC from the payload length
Suggested-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-6-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The naming of can_dlc as element of struct can_frame and also as variable
name is misleading as it claims to be a 'data length CODE' but in reality
it always was a plain data length.
With the indroduction of a new 'len' element in struct can_frame we can now
remove can_dlc as name and make clear which of the former uses was a plain
length (-> 'len') or a data length code (-> 'dlc') value.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201120100444.3199-1-socketcan@hartkopp.net
[mkl: gs_usb: keep struct gs_host_frame::can_dlc as is]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Avoid processing bogus interrupt statuses when the HW is runtime suspended and
the M_CAN_IR register read may get all bits 1's. Handler can be called if the
interrupt request is shared with other peripherals or at the end of free_irq().
Therefore check the runtime suspended status before processing.
Fixes: cdf8259d65 ("can: m_can: Add PM Support")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20200915134715.696303-1-jarkko.nikula@linux.intel.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the CAN controller goes into bus off, the do_set_mode() callback with
CAN_MODE_START can be used to recover the controller, which then calls
flexcan_chip_start(). If configured, this is done automatically by the
framework or manually by the user.
In flexcan_chip_start() there is an explicit call to
flexcan_transceiver_enable(), which does a regulator_enable() on the
transceiver regulator. This results in a net usage counter increase, as there
is no corresponding flexcan_transceiver_disable() in the bus off code path.
This further leads to the transceiver stuck enabled, even if the CAN interface
is shut down.
To fix this problem the
flexcan_transceiver_enable()/flexcan_transceiver_disable() are moved out of
flexcan_chip_start()/flexcan_chip_stop() into flexcan_open()/flexcan_close().
Fixes: e955cead03 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20201118150148.2664024-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There might be some requests pending in the buffer when the interface close
sequence occurs. In some devices, these pending requests might lead to the
module not shutting down properly when m_can_clk_stop() is called.
Therefore, move the device to init state before potentially powering it down.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200825055442.16994-1-faiz_abbas@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can_handle_state_change() is called with the new_state as an argument.
In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the
following code indicate that a CAN_STATE_ERROR_WARNING is handled.
This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING.
Signed-off-by: Wu Bo <wubo.oduw@gmail.com>
Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com
Cc: Dan Murphy <dmurphy@ti.com>
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
regmap is a library function that gets selected by drivers that need it. No
driver modules should depend on it. Instead depends on SPI and select
REGMAP_SPI. Depending on REGMAP_SPI makes this driver only build if another
driver already selected REGMAP_SPI, as the symbol can't be selected through the
menu kernel configuration.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: http://lore.kernel.org/r/20200413141013.506613-1-enric.balletbo@collabora.com
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
