In the case where st->ch_map[GRTS_CH_PRESSURE] < GRTS_MAX_CHANNELS is false
and also st->ch_map[GRTS_CH_Z1] < GRTS_MAX_CHANNELS is false the variable
press is not initialized and contains garbage. In this situation
st->pressure is also false, so we do not actually use press value, but
it is impossible for the compiler to realize this, and it emits
"uninitialized variable" warning. Fix this by initializing press
to 0 and allows us to also remove an else clause that sets press to 0.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 60b7db914d ("Input: resistive-adc-touch - rework mapping of channels")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210603220809.155118-1-colin.king@canonical.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At the moment, the edt-ft5x06 driver can control a single regulator
("vcc"). However, some FocalTech touch controllers have an additional
IOVCC pin that should be supplied with the digital I/O voltage.
The I/O voltage might be provided by another regulator that should also
be kept on. Otherwise, the touchscreen can randomly stop functioning if
the regulator is turned off because no other components still require it.
Implement (optional) support for also enabling an "iovcc-supply".
The datasheet specifies a delay of ~ 10us before enabling VDD/VCC
after IOVCC is enabled, so make sure to enable IOVCC first.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210510193108.50178-2-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the four control requests which erroneously used usb_rcvctrlpipe().
Fixes: 1d3e20236d ("[PATCH] USB: usbtouchscreen: unified USB touchscreen driver")
Fixes: 24ced062a2 ("usbtouchscreen: add support for DMC TSC-10/25 devices")
Fixes: 9e3b25837a ("Input: usbtouchscreen - add support for e2i touchscreen controller")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 2.6.17
Link: https://lore.kernel.org/r/20210524092048.4443-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move the DMI quirks for upside-down mounted Goodix touchscreens from
drivers/input/touchscreen/goodix.c to
drivers/platform/x86/touchscreen_dmi.c,
where all the other x86 touchscreen quirks live.
Note the touchscreen_dmi.c code attaches standard touchscreen
device-properties to an i2c-client device based on a combination of a
DMI match + a device-name match. I've verified that the: Teclast X98 Pro,
WinBook TW100 and WinBook TW700 uses an ACPI devicename of "GDIX1001:00"
based on acpidumps and/or dmesg output available on the web.
This patch was tested on a Teclast X89 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210504185746.175461-2-hdegoede@redhat.com
Pull input updates from Dmitry Torokhov:
- three new touchscreen drivers: Hycon HY46XX, ILITEK Lego Series,
and MStar MSG2638
- a new driver for Azoteq IQS626A proximity and touch controller
- addition of Amazon Game Controller to the list of devices handled
by the xpad driver
- Elan touchscreen driver will avoid binding to devices described as
I2CHID compatible in ACPI tables
- various driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (56 commits)
Input: xpad - add support for Amazon Game Controller
Input: ili210x - add missing negation for touch indication on ili210x
MAINTAINERS: repair reference in HYCON HY46XX TOUCHSCREEN SUPPORT
Input: add driver for the Hycon HY46XX touchpanel series
dt-bindings: touchscreen: Add HY46XX bindings
dt-bindings: Add Hycon Technology vendor prefix
Input: cyttsp - flag the device properly
Input: cyttsp - set abs params for ABS_MT_TOUCH_MAJOR
Input: cyttsp - drop the phys path
Input: cyttsp - reduce reset pulse timings
Input: cyttsp - error message on boot mode exit error
Input: apbps2 - remove useless variable
Input: mms114 - support MMS136
Input: mms114 - convert bindings to YAML and extend
Input: Add support for ILITEK Lego Series
dt-bindings: input: touchscreen: ilitek_ts_i2c: Add bindings
Input: add MStar MSG2638 touchscreen driver
dt-bindings: input/touchscreen: add bindings for msg2638
Input: silead - add workaround for x86 BIOS-es which bring the chip up in a stuck state
Input: elants_i2c - do not bind to i2c-hid compatible ACPI instantiated devices
...
This adds the negation needed for proper finger detection on Ilitek
ili2107/ili210x. This fixes polling issues (on Amazon Kindle Fire)
caused by returning false for the cooresponding finger on the touchscreen.
Signed-off-by: Hansem Ro <hansemro@outlook.com>
Fixes: e3559442af ("ili210x - rework the touchscreen sample processing")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance
optimized for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target
module has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
avoid issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as
we now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for
omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of
using builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"
* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: aspeed: fix a ternary sign expansion bug
memory: mtk-smi: Add device-link between smi-larb and smi-common
memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
clk: socfpga: fix iomem pointer cast on 64-bit
soc: aspeed: Adapt to new LPC device tree layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
ARM: dts: Remove LPC BMC and Host partitions
dt-bindings: aspeed-lpc: Remove LPC partitioning
soc: fsl: enable acpi support in RCPM driver
soc: qcom: mdt_loader: Detect truncated read of segments
soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
soc: qcom: pdr: Fix error return code in pdr_register_listener
firmware: qcom_scm: Fix kernel-doc function names to match
firmware: qcom_scm: Suppress sysfs bind attributes
firmware: qcom_scm: Workaround lack of "is available" call on SC7180
firmware: qcom_scm: Reduce locking section for __get_convention()
firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
...
Pull input fixes from Dmitry Torokhov:
"Just a few driver fixes here"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elants_i2c - drop zero-checking of ABS_MT_TOUCH_MAJOR resolution
Input: elants_i2c - fix division by zero if firmware reports zero phys size
Input: nspire-keypad - enable interrupts only when opened
Input: i8042 - fix Pegatron C15B ID entry
Input: n64joy - fix return value check in n64joy_probe()
Input: s6sy761 - fix coordinate read bit shift
When I test to use the CY8CTMA340 with PostmarketOS I don't have any
problem whatsoever in dropping this phys path, it finds and uses the
touchscreen just as well. I suppose it is because userspace is using
modern input libraries.
I challenge the maintainers to point out a valid and still used
userspace that actually need this. I say we drop it.
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210408131153.3446138-7-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The data sheet for CY8CTMA340 specifies that the reset pulse shall be at
least 1 ms. Specify 1-2 ms with usleep_range() to cut some slack for the
scheduler.
Curiously the datasheet does not specify how long we have to wait after a
hard reset until the chip is up, but I have found a vendor tree (Samsung
GT-S7710) that has code for this touch screen and there this is set to 5
ms so I use this with the same 1 ms fuzz.
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210408131153.3446138-6-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Melfas MMS136 is similar to the other MMS variants but
has event packages of 6 bytes rather than 8 as the others.
The define is named FINGER_EVENT_SZ in the vendor drivers
so I renamed it from MMS*_PACKET_SZ to MMS*_EVENT_SZ.
After this patch, the touchscreen on the Samsung GT-I8530
works fine with PostmarketOS.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210404232619.3092682-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some buggy BIOS-es bring up the touchscreen-controller in a stuck
state where it blocks the I2C bus. Specifically this happens on
the Jumper EZpad 7 tablet model.
After much poking at this problem I have found that the following steps
are necessary to unstuck the chip / bus:
1. Turn off the Silead chip.
2. Try to do an I2C transfer with the chip, this will fail in response to
which the I2C-bus-driver will call: i2c_recover_bus() which will unstuck
the I2C-bus. Note the unstuck-ing of the I2C bus only works if we first
drop the chip of the bus by turning it off.
3. Turn the chip back on.
On the x86/ACPI systems were this problem is seen, step 1. and 3. require
making ACPI calls and dealing with ACPI Power Resources. This commit adds
a workaround which runtime-suspends the chip to turn it off, leaving it up
to the ACPI subsystem to deal with all the ACPI specific details.
There is no good way to detect this bug, so the workaround gets activated
by a new "silead,stuck-controller-bug" boolean device-property. Since this
is only used on x86/ACPI, this will be set by model specific device-props
set by drivers/platform/x86/touchscreen_dmi.c. Therefor this new
device-property is not documented in the DT-bindings.
Dmesg will contain the following messages on systems where the workaround
is activated:
[ 54.309029] silead_ts i2c-MSSL1680:00: [Firmware Bug]: Stuck I2C bus: please ignore the next 'controller timed out' error
[ 55.373593] i2c_designware 808622C1:04: controller timed out
[ 55.582186] silead_ts i2c-MSSL1680:00: Silead chip ID: 0x80360000
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202745.16777-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Several users have been reporting that elants_i2c gives several errors
during probe and that their touchscreen does not work on their Lenovo AMD
based laptops with a touchscreen with a ELAN0001 ACPI hardware-id:
[ 0.550596] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vcc33 not found, using dummy regulator
[ 0.551836] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vccio not found, using dummy regulator
[ 0.560932] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.562427] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.595925] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.597974] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.621893] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.622504] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.632650] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (4d 61 69 6e): -121
[ 0.634256] elants_i2c i2c-ELAN0001:00: boot failed: -121
[ 0.699212] elants_i2c i2c-ELAN0001:00: invalid 'hello' packet: 00 00 ff ff
[ 1.630506] elants_i2c i2c-ELAN0001:00: Failed to read fw id: -121
[ 1.645508] elants_i2c i2c-ELAN0001:00: unknown packet 00 00 ff ff
Despite these errors, the elants_i2c driver stays bound to the device
(it returns 0 from its probe method despite the errors), blocking the
i2c-hid driver from binding.
Manually unbinding the elants_i2c driver and binding the i2c-hid driver
makes the touchscreen work.
Check if the ACPI-fwnode for the touchscreen contains one of the i2c-hid
compatiblity-id strings and if it has the I2C-HID spec's DSM to get the
HID descriptor address, If it has both then make elants_i2c not bind,
so that the i2c-hid driver can bind.
This assumes that non of the (older) elan touchscreens which actually
need the elants_i2c driver falsely advertise an i2c-hid compatiblity-id
+ DSM in their ACPI-fwnodes. If some of them actually do have this
false advertising, then this change may lead to regressions.
While at it also drop the unnecessary DEVICE_NAME prefixing of the
"I2C check functionality error", dev_err already outputs the driver-name.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207759
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202756.16830-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable because of requesting.
On the other hand, request_irq() after setting IRQ_NOAUTOEN as
below
irq_set_status_flags(irq, IRQ_NOAUTOEN);
request_irq(dev, irq...);
can also be replaced by request_irq() with IRQF_NO_AUTOEN flag.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20210302224916.13980-3-song.bao.hua@hisilicon.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The first thing the Cypress driver does when starting
up is to try a soft reset. This is the first point where
the driver SPI/I2C communication can fail, so put out some
nice debug text:
cyttsp-spi spi2.0: failed to send soft reset
Instead of just:
cyttsp-spi: probe of spi2.0 failed with error -5
This is more helpful.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210322221349.1116666-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device's hardware reset pin is only required if the platform
must be able to update the device's firmware.
As such, demote the reset GPIO to optional in support of devices
that ship with pre-programmed firmware and don't route the reset
pin back to the SoC.
In that case, the 'fw_file' attribute is hidden because there is
no way to open the bootloader. The logic is extended to the case
in which the device does not advertise bootloader support in the
first place.
Last but not least, remove the hardware reset performed at probe
because there is no reason to reset the device manually. A power
on reset function already ensures a clean reset at start-up.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210323021006.367-1-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some devices outside of drivers/input/touchscreen/ can still make
use of the touchscreen helper functions. Therefore, it was agreed
in [1] to move them outside of drivers/input/touchscreen/ so that
other devices can call them without INPUT_TOUCHSCREEN being set.
As part of this change, 'of' is dropped from the filename because
the helpers no longer actually use OF. No changes are made to the
file contents whatsoever.
Based on the feedback in [2], the corresponding binding documents
(touchscreen.yaml and touchscreen.txt) are left in their original
locations.
[1] https://patchwork.kernel.org/patch/11924029/
[2] https://patchwork.kernel.org/patch/12042037/
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210301234928.4298-2-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The bootloader can be closed using the 'execute' command (0x02) or
hardware reset. Rather than using the former option for successful
firmware update procedures and reserving the latter for recovering
the device upon failure, simply use hardware reset for all cases.
The post-bootloader initialization delay increases marginally when
triggered by a hardware reset, so increase the wait time to ensure
the device does not subsequently fail to respond.
As part of this change, refactor the return path to avoid an extra
assignment and to make the logic a bit smaller.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-6-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The vendor-assigned firmware project number is restricted to the
generic project number (15); however the vendor may assign other
project numbers to specific applications and customers.
These custom project numbers may be based on forwards-compatible
firmware revision 1.x. However, the driver unnecessarily rejects
anything older than firmware revision 2.0.
To support other applications, remove these unnecessarily strict
checks and enter the bootloader only for truly incompatible A000
devices.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-5-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the read-only 'fw_info' attribute which reports information
about the device's firmware in the following format:
a.b.c.d:e.f
Where:
a = Product number (e.g. 40 for IQS550)
b = Project number (e.g. 15)
c = Firmware revision (major)
d = Firmware revision (minor)
e = Customer-assigned exported file version (major)
f = Customer-assigned exported file version (minor)
As part of the corresponding rework to uses of 'bl_status', the
IQS5XX_BL_STATUS_RESET definition is dropped with 0 used in its
place instead.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-4-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
