This patch adds a hwmon driver for the AHT10 Temperature and
Humidity sensor. It has a maximum sample rate, as the datasheet
states that the chip may heat up if it is sampled more than once
every two seconds.
Has been tested a to work on a raspberrypi0w
Signed-off-by: Johannes Cornelis Draaijer (datdenkikniet) <jcdra1@gmail.com>
Link: https://lore.kernel.org/r/20210107194014.GA88780@desktop
[groeck: dropped AHT10_ADDR (unused) and use AHT10_MEAS_SIZE where
appropriate; dropped change log]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pwm-fan driver is extended to support multiple fan tachometer
signals connected to GPIO inputs. This is intended to support the case
where a single PWM output signal is routed to multiple fans, each of
which have a tachometer output connected back to a GPIO pin.
The number of fan tachometer inputs is determined by the number of
interrupt sources configured for the pwm-fan device. The number of
pulses-per-revolution entries should match the number of interrupt
sources so that each input has a value assigned.
The fan tachometer measurements are exposed as sysfs files fan1_input,
fan2_input, etc up to the number of configured inputs.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Link: https://lore.kernel.org/r/20201212195008.6036-3-pbarker@konsulko.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The data for the (optional) fan tachometer input is moved to a separate
structure which is only allocated if an input is actually configured.
After this change the pulse IRQ handler takes a pointer to the
tachometer data structure instead of the whole device context.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Link: https://lore.kernel.org/r/20201212195008.6036-2-pbarker@konsulko.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several power supplies supported by the IBM CFFPS driver don't
report valid data in the CAPABILITY register. This results in PEC
being enabled when it's not supported by the device, and since
the automatic version detection might fail, disable use of the
CAPABILITY register across the board for this driver.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20201222152640.27749-3-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This deletes the ABx500 hwmon driver, the only supported
variant being the AB8500.
This driver has been replaced by generic frameworks. By
inspecting the abx500 sysfs files we see that it contains
things such as temp1_max, temp1_max_alarm, temp1_max_hyst,
temp1_max_hyst_alarm, temp1_min, temp1_min_alarm.
It becomes obvious that the abx500.c is a reimplementation
of thermal zones. This is not very strange as the generic
thermal zones were not invented when this driver was merged
so people were rolling their own.
The ab8500.c driver contains conversion tables for handling
a thermistor on ADC channels AUX1 and AUX2.
I managed to replace the functionality of the driver with:
- Activation of the ntc_thermistor.c driver,
CONFIG_SENSORS_NTC_THERMISTOR
- Activation of thermal zones, CONFIG_THERMAL
- In the device tree, connecting the NTC driver to the
processed IIO channels from the AB8500 GPADC ADC forming
two instances of NTC sensors.
- Connecting the two NTC sensors to a "chassis" thermal zone
in the device tree and setting that to hit the CPU frequency
at 50 degrees celsius and do a critical shutdown at 70
degrees celsius, deploying a policy using the sensors.
After talking to the original authors we concluded that the
driver was never properly parameterized in production so
what we now have in the device tree is already puts the
thermistors to better use than what the hwmon driver did.
The two remaining channels for two battery temperatures is
already handled in the charging algorithms but can be
optionally extended to thermal zones as well if we want
these to trigger critical shutdown for the platform.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201221125521.768082-1-linus.walleij@linaro.org
[groeck: Removed documentation and fixed up Makefile, Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
With MAX_PWM being defined to 255 the code
unsigned long period;
...
period = ctx->pwm->args.period;
state.duty_cycle = DIV_ROUND_UP(pwm * (period - 1), MAX_PWM);
calculates a too small value for duty_cycle if the configured period is
big (either by discarding the 64 bit value ctx->pwm->args.period or by
overflowing the multiplication). As this results in a too slow fan and
so maybe an overheating machine better be safe than sorry and error out
in .probe.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201215092031.152243-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Voltages and current are reported by Zen CPUs. However, the means
to do so is undocumented, changes from CPU to CPU, and the raw data
is not calibrated. Calibration information is available, but again
not documented. This results in less than perfect user experience,
up to concerns that loading the driver might possibly damage
the hardware (by reporting out-of range voltages). Effectively
support for reporting voltages and current is not maintainable.
Drop it.
Cc: Artem S. Tashkinov <aros@gmx.com>
Cc: Wei Huang <wei.huang2@amd.com>
Tested-by: Wei Huang <wei.huang2@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
interface that reports AMD SoC's Ttcl (normalized temperature),
and resembles a typical 8-pin remote temperature sensor's I2C interface
to BMC.
This commit adds basic support using this interface to read CPU
temperature, and read/write high/low CPU temp thresholds.
To instantiate this driver on an AMD CPU with SB-TSI
support, the i2c bus number would be the bus connected from the board
management controller (BMC) to the CPU. The i2c address is specified in
Section 6.3.1 of the spec [1]: The SB-TSI address is normally 98h for
socket 0 and 90h for socket 1, but it could vary based on hardware address
select pins.
[1]: https://www.amd.com/system/files/TechDocs/56255_OSRR.pdf
Test status: tested reading temp1_input, and reading/writing
temp1_max/min.
Signed-off-by: Kun Yi <kunyi@google.com>
Link: https://lore.kernel.org/r/20201211215427.3281681-2-kunyi@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2992 has 4 open-drain GPIOS. This patch exports to user
space the 4 GPIOs using the GPIO driver Linux API.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2992 is a rail-to-rail system monitor that
measures current, voltage, and power of two supplies.
Two ADCs simultaneously measure each supply’s current.
A third ADC monitors the input voltages and four
auxiliary external voltages.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the pmbus driver for the STMicroelectronics pm6764 voltage regulator.
the output voltage use the MFR_READ_VOUT 0xD4
vout value returned is linear11
Signed-off-by: Charles Hsu <hsu.yungteng@gmail.com>
[groeck: Fixed various compile errors; marked pm6764tr_of_match __maybe_unused]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds the DMI Product ID for Intel-based Xserve machines.
They use the same SMC accessible from the same data ports.
The 'Xserve' product ID only resolves to SMC-containing
Intel-based Xserves, as the PowerPC machines are identified
by the 'RackMac' identifier.
Tested on: Xserve3,1
Tested-by: Joe Jamison <joe@smaklab.com> # Xserve3,1
Signed-off-by: Joe Jamison <joe@smaklab.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pwm-fan driver is updated to use the recommended API.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
[groeck: Dropped unused variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use platform_irq_count to determine the number of fan tachometer inputs
configured in the device tree. At this stage we support either 0 or 1
inputs.
Once we have this information we only need to read the
pulses-per-revolution value if a fan tachometer is actually configured
via an IRQ value.
Also add a debug print of the IRQ number and the pulses-per-revolution
value to aid in investigating issues.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201126174408.755-2-pbarker@konsulko.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Kerneldoc expects attributes/parameters to be in '@*.: ' format.
Also fix repeated word "the the".
Fixes the following W=1 kernel build warning(s):
drivers/hwmon/adm1177.c:40: warning: Function parameter or member 'client' not described in 'adm1177_state'
drivers/hwmon/adm1177.c:40: warning: Function parameter or member 'reg' not described in 'adm1177_state'
drivers/hwmon/adm1177.c:40: warning: Function parameter or member 'r_sense_uohm' not described in 'adm1177_state'
drivers/hwmon/adm1177.c:40: warning: Function parameter or member 'alert_threshold_ua' not described in 'adm1177_state'
drivers/hwmon/adm1177.c:40: warning: Function parameter or member 'vrange_high' not described in 'adm1177_state'
Cc: Beniamin Bia <beniamin.bia@analog.com>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112095715.1993117-2-lee.jones@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shifting of the u8 integer data[3] by 24 bits to the left will
be promoted to a 32 bit signed int and then sign-extended to a
long. In the event that the top bit of data[3] is set then all
then all the upper 32 bits of a 64 bit long end up as also being
set because of the sign-extension. Fix this by casting data[3] to
a long before the shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: ce15cd2cee8b ("hwmon: add Corsair PSU HID controller driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201105115019.41735-1-colin.king@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Corsair digital power supplies of the series RMi, HXi and AXi include
a small micro-controller with a lot of sensors attached. The sensors can
be accessed by an USB connector from the outside.
This micro-controller provides the data by a simple proprietary USB HID
protocol. The data consist of temperatures, current and voltage levels,
power usage, uptimes, fan speed and some more. It is also possible to
configure the PSU (fan mode, mono/multi-rail, over current protection).
This driver provides access to the sensors/statistics of the RMi and HXi
series power supplies. It does not support configuring these devices,
because there would be many ways to misconfigure or even damage the PSU.
This patch adds:
- hwmon driver corsair-psu
- hwmon documentation
- updates MAINTAINERS
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/20201027131710.GA253280@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The only action currently performed in pmbus_do_remove() is removing the
debugfs hierarchy. We can schedule a devm action at probe time and remove
pmbus_do_remove() entirely from all pmbus drivers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20201026105352.20359-1-brgl@bgdev.pl
[groeck: Removed references to pmbus_do_remove from documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The debugfs_create_dir() function never returns NULL. Normal users are
not supposed to check the return value so the correct fix is just to
delete this check.
In the case where the debugfs_create_dir() fails, the function returns
NULL. The other debugfs function check for NULL directory and handle
it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201022070659.GA2817762@mwanda
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This code works okay but Smatch flagged it as a double free. I've
changed three things to make it more clear. 1) Remove the call to
free_capabilities() in acpi_power_meter_add(). This call is a no-op
because the capabilities have not been allocated yet. 2) Set "*str" to
NULL in free_capabilities() so that way the function can be called twice
in a row without leading to a double free. 3) Call free_capabilities()
in read_capabilities() instead of open coding the free.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201007075148.GB2529578@mwanda
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pm_runtime_get_sync will increment pm usage counter
even it failed. Forgetting to putting operation will
result in reference leak here. We fix it by replacing
it with pm_runtime_resume_and_get to keep usage counter
balanced. It depends on the mainline commit[PM: runtime:
Add pm_runtime_resume_and_get to deal with usagecounter].
Fixes: 323aeb0eb5 ("hwmon: (ina3221) Add PM runtime support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201202145320.1135614-1-zhangqilong3@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
