Widebus feature will transmit two pixel data per pixel clock to interface.
This feature now is required to be enabled to easy migrant to higher
resolution applications in future. However since some legacy chipsets
does not support this feature, this feature is enabled by setting
wide_bus_en flag to true within msm_dp_desc struct.
changes in v2:
-- remove compression related code from timing
-- remove op_info from struct msm_drm_private
-- remove unnecessary wide_bus_en variables
-- pass wide_bus_en into timing configuration by struct msm_dp
Changes in v3:
-- split patch into 3 patches
-- enable widebus feature base on chip hardware revision
Changes in v5:
-- DP_INTF_CONFIG_DATABUS_WIDEN
Changes in v6:
-- static inline bool msm_dp_wide_bus_enable() in msm_drv.h
Changes in v7:
-- add Tested-by
Changes in v9:
-- add wide_bus_en to msm_dp_desc
Changes in v10:
-- add wide_bus_en boolean to dp_catalog struc to avoid passing it as parameter
Changes in v11:
-- add const to dp_catalog_hw_revision()
-- add const to msm_dp_wide_bus_available()
Changes in v12:
-- dp_catalog_hw_revision(const struct dp_catalog *dp_catalog)
-- msm_dp_wide_bus_available(const struct msm_dp *dp_display)
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/476283/
Link: https://lore.kernel.org/r/1645824192-29670-5-git-send-email-quic_khsieh@quicinc.com
[DB: fixed the compilation]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Widebus feature will transmit two pixel data per pixel clock to interface.
Timing engine provides driving force for this purpose. This patch base
on HPG (Hardware Programming Guide) to revise timing engine register
setting to accommodate both widebus and non widebus application. Also
horizontal width parameters need to be reduced by half since two pixel
data are clocked out per pixel clock when widebus feature enabled.
Widebus can be enabled individually at DP. However at DSI, widebus have
to be enabled along with DSC to achieve pixel clock rate be scaled down
with same ratio as compression ratio when 10 bits per source component.
Therefore this patch add no supports of DSI related widebus and compression.
Changes in v2:
-- remove compression related code from timing
-- remove op_info from struct msm_drm_private
-- remove unnecessary wide_bus_en variables
-- pass wide_bus_en into timing configuration by struct msm_dp
Changes in v3:
-- split patch into 3 patches
Changes in v4:
-- rework timing engine to not interfere with dsi/hdmi
-- cover both widebus and compression
Changes in v5:
-- remove supports of DSI widebus and compression
Changes in v7:
-- split this patch into 3 patches
-- add Tested-by
Changes in v8:
-- move new registers writes under DATA_HCTL_EN features check.
Changes in v10:
-- add const inside dpu_encoder_is_widebus_enabled()
-- drop useless parenthesis please
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/476281/
Link: https://lore.kernel.org/r/1645824192-29670-4-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The msm_mdss serves several roles at this moment. It provides IRQ domain
used by MDP5 and DPU drivers but it also serves as a component master
for both those usecases. MDP4 (which does not have separate MDSS device)
is the component master on it's own.
Remove this assymmetry and make both MDP5 and DPU component masters too.
This removes a need to care about drm/components from msm_mdss driver,
removes an mdss pointer from struct msm_drm_private and simplifies the
interface between mdp5/dpu and msm_drv.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/482512/
Link: https://lore.kernel.org/r/20220419155346.1272627-7-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
While there's a comment pointing from dpu_intr_set to dpu_hw_intr_reg
and vice-versa, an array initializer using indices makes it so that the
indices between the enum and array cannot possibly get out of sync even
if they're accidentially ordered wrongly. It is still useful to keep
the comment to be made aware where the register offset mapping resides
while looking at dpu_hw_intr_reg.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220226194633.204501-1-marijn.suijten@somainline.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
We're experimenting a bit with the process this time, with Dmitry
collecting display patches and merging them into msm-next with me
handling the gpu/etc side of things. Summary of interesting new bits
and pieces
* dpu + dp support for sc8180x
* dp support for sm8350
* dpu + dsi support for qcm2290
* 10nm dsi phy tuning support
* bridge support for dp encoder
* gpu support for additional 7c3 SKUs
* assorted cleanups and fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGu=Jdrw6DqYOYPTMks7=zatrsvdR=o6DpjqZ=TQQhFZuw@mail.gmail.com
Someone on IRC once asked an innocent enough sounding question: Why
with xf86-video-modesetting is es2gears limited at 120fps.
So I broke out the perfetto tracing mesa MR and took a look. It turns
out the problem was drm_atomic_helper_dirtyfb(), which would end up
waiting for vblank.. es2gears would rapidly push two frames to Xorg,
which would blit them to screen and in idle hook (I assume) call the
DIRTYFB ioctl. Which in turn would do an atomic update to flush the
dirty rects, which would stall until the next vblank. And then the
whole process would repeat.
But this is a bit silly, we only need dirtyfb for command mode DSI
panels. So track in plane state whether dirtyfb is required, and
track in the fb how many attached planes require dirtyfb so that we
can skip it when not required. (Note, mdp4 does not actually have
cmd mode support.)
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220223191118.881321-1-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
In function dpu_encoder_phys_cmd_wait_for_commit_done we are always
checking if the relative CTL is started by waiting for an interrupt
to fire: it is fine to do that, but then sometimes we call this
function while the CTL is up and has never been put down, but that
interrupt gets raised only when the CTL gets a state change from
0 to 1 (disabled to enabled), so we're going to wait for something
that will never happen on its own.
Solving this while avoiding to restart the CTL is actually possible
and can be done by just checking if it is already up and running
when the wait_for_commit_done function is called: in this case, so,
if the CTL was already running, we can say that the commit is done
if the command transmission is complete (in other terms, if the
interface has been flushed).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210911163919.47173-2-angelogioacchino.delregno@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DPU driver contains code to parse clock items from device tree into
special data struct and then enable/disable/set rate for the clocks
using that data struct. However the DPU driver itself uses only parsing
and enabling/disabling part (the rate setting is used by DP driver).
Move this implementation to the DP driver (which actually uses rate
setting) and replace hand-coded enable/disable/get loops in the DPU
with the respective clk_bulk operations. Put operation is removed
completely because, it is handled using devres instead.
DP implementation is unchanged for now.
Tested-by: Jessica Zhang <quic_jesszhan@quicinc.com> # RB3 (sdm845) and RB5 (qrb5165)
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220217055529.499829-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
dpu_kms_debugfs_init() is invoked for each minor being registered. Most
of the files created are unrelated to the minor, so there's no reason to
present them per minor.
The exception to this is the DisplayPort code, which ends up invoking
dp_debug_get() for each minor, each time associate the allocated object
with dp->debug.
As such dp_debug will create debugfs files in both the PRIMARY and the
RENDER minor's debugfs directory, but only the last reference will be
remembered.
The only use of this reference today is in the cleanup path in
dp_display_deinit_sub_modules() and the dp_debug_private object does
outlive the debugfs entries in either case, so there doesn't seem to be
any adverse effects of this, but per the code the current behavior is
unexpected, so change it to only create debugfs files for the PRIMARY
minor.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[DB: slightly change description and in-patch comment]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20220212003811.1818774-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add SC8180x to the hardware catalog, for initial support for the
platform. Due to limitations in the DP driver only one of the four DP
interfaces is left enabled.
The SC8180x platform supports the newly added DPU_INTF_WIDEBUS flag and
the Windows-on-Snapdragon bootloader leaves the widebus bit set, so this
is flagged appropriately to ensure widebus is disabled - for now.
Signed-off-by: Rob Clark <robdclark@chromium.org>
[bjorn: Reworked intf and irq definitions]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
