Rework mgag200_regs_init() and mgag200_mm_init() into device preinit
and init functions. The preinit function, mgag200_device_preinit(),
requests and maps a device's I/O and video memory. The init function,
mgag200_device_init() initializes the state of struct mga_device.
Splitting the initialization between the two functions is necessary
to perform per-model operations between the two calls, such as reading
the unique revision ID on G200SEs.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112522.5774-6-tzimmermann@suse.de
Remove old test for 32-bit vs 16-bit colors. Prefer 24-bit color depth
on all devices. 32-bit color depth doesn't exist, it should have always
been 24-bit.
G200SE with less than 2 MiB of video memory have defaulted to 16-bit
color depth, as the original revision of the G200SE had only 1.75 MiB
of video memory. Using 16-bit colors enabled XGA resolution. But we
now already limit these devices to VGA resolutions as the memory-bandwith
test assumes 32-bit pixel size. So drop the special case from color-depth
selection.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112522.5774-2-tzimmermann@suse.de
Split up the connector's mode_valid helper into a simple-pipe and a
mode-config helper. The simple-pipe helper tests for display-size
limits while the mode-config helper tests for memory-bandwidth limits.
Also add the mgag200_ prefix to mga_vga_calculate_mode_bandwidth() and
comment on the function's purpose.
The memory-bandwidth tests assume that the display uses 4 bytes per
pixel. The first models of G200SE-A only had 1.75 MiB of VRAM, which
limits these devices to 640x480-32.
v2:
* note the memory constraints on early G200SE-A
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220516134343.6085-8-tzimmermann@suse.de
Test for a mode's memory requirements in the device-wide mode_valid
helper. For simplicify, always assume a 32-bit color format. While
some rejected modes would work with less colors, implementing this
is probably not worth the effort.
Also remove the memory-related test from the connector's mode_valid
helper. The test uses the bpp value that users can specify on the
kernel's command line. This value is unrelated and the test would
belong into atomic_check.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220516134343.6085-7-tzimmermann@suse.de
Initialization of the I2C adapter was allowed to fail. The mgag200
driver would have continued without DDC support. Had this happened in
practice, it would have led to segmentation faults in the connector
code. Resolve this problem by failing driver initialization on I2C-
related errors.
v2:
* initialize 'ret' before drm_err() (kernel test robot)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220516134343.6085-3-tzimmermann@suse.de
Add support for atomic update of gamma lut.
With this patch the "Night light" feature of gnome3
is working properly on mgag200.
v2:
- Add a default linear gamma function
- renamed functions with mgag200 prefix
- use format's 4cc code instead of bit depth
- use better interpolation for 16bits gamma
- remove legacy function mga_crtc_load_lut()
- can't remove the call to drm_mode_crtc_set_gamma_size()
because it doesn't work with userspace.
- other small refactors
v3:
- change mgag200_crtc_set_gamma*() argument
to struct drm_format_info *format
- fix printk format to %p4cc for 4cc and %zu for size_t
- rebased to drm-misc-next.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220513084900.1832381-1-jfalempe@redhat.com
The driver does support damage clips, but doesn't advertise it.
So when running gnome/wayland on Matrox hardware, the full frame is
copied to the slow Matrox memory, which leads to very poor performances.
Add drm_plane_enable_fb_damage_clips() to advertise this capability to
userspace.
With this patch, gnome/wayland becomes usable on Matrox GPU.
Suggested-by: Jonas Ådahl <jadahl@gmail.com>
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220504134026.283417-2-jfalempe@redhat.com
Add a mutex lock to protect concurrent access to I/O registers
against each other. This happens between invocation of commit-
tail functions and get-mode operations. Both with use the CRTC
index registers MGA1064_GEN_IO_DATA and MGA1064_GEN_IO_CTL.
Concurrent access can lead to failed mode-setting operations.
v2:
* fix typo in commit description (Jocelyn)
* add comment to explain rmmio_lock
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220502142514.2174-4-tzimmermann@suse.de
Pull drm updates from Dave Airlie:
"Lots of work all over, Intel improving DG2 support, amdkfd CRIU
support, msm new hw support, and faster fbdev support.
dma-buf:
- rename dma-buf-map to iosys-map
core:
- move buddy allocator to core
- add pci/platform init macros
- improve EDID parser deep color handling
- EDID timing type 7 support
- add GPD Win Max quirk
- add yes/no helpers to string_helpers
- flatten syncobj chains
- add nomodeset support to lots of drivers
- improve fb-helper clipping support
- add default property value interface
fbdev:
- improve fbdev ops speed
ttm:
- add a backpointer from ttm bo->ttm resource
dp:
- move displayport headers
- add a dp helper module
bridge:
- anx7625 atomic support, HDCP support
panel:
- split out panel-lvds and lvds bindings
- find panels in OF subnodes
privacy:
- add chromeos privacy screen support
fb:
- hot unplug fw fb on forced removal
simpledrm:
- request region instead of marking ioresource busy
- add panel oreintation property
udmabuf:
- fix oops with 0 pages
amdgpu:
- power management code cleanup
- Enable freesync video mode by default
- RAS code cleanup
- Improve VRAM access for debug using SDMA
- SR-IOV rework special register access and fixes
- profiling power state request ioctl
- expose IP discovery via sysfs
- Cyan skillfish updates
- GC 10.3.7, SDMA 5.2.7, DCN 3.1.6 updates
- expose benchmark tests via debugfs
- add module param to disable XGMI for testing
- GPU reset debugfs register dumping support
amdkfd:
- CRIU support
- SDMA queue fixes
radeon:
- UVD suspend fix
- iMac backlight fix
i915:
- minimal parallel submission for execlists
- DG2-G12 subplatform added
- DG2 programming workarounds
- DG2 accelerated migration support
- flat CCS and CCS engine support for XeHP
- initial small BAR support
- drop fake LMEM support
- ADL-N PCH support
- bigjoiner updates
- introduce VMA resources and async unbinding
- register definitions cleanups
- multi-FBC refactoring
- DG1 OPROM over SPI support
- ADL-N platform enabling
- opregion mailbox #5 support
- DP MST ESI improvements
- drm device based logging
- async flip optimisation for DG2
- CPU arch abstraction fixes
- improve GuC ADS init to work on aarch64
- tweak TTM LRU priority hint
- GuC 69.0.3 support
- remove short term execbuf pins
nouveau:
- higher DP/eDP bitrates
- backlight fixes
msm:
- dpu + dp support for sc8180x
- dp support for sm8350
- dpu + dsi support for qcm2290
- 10nm dsi phy tuning support
- bridge support for dp encoder
- gpu support for additional 7c3 SKUs
ingenic:
- HDMI support for JZ4780
- aux channel EDID support
ast:
- AST2600 support
- add wide screen support
- create DP/DVI connectors
omapdrm:
- fix implicit dma_buf fencing
vc4:
- add CSC + full range support
- better display firmware handoff
panfrost:
- add initial dual-core GPU support
stm:
- new revision support
- fb handover support
mediatek:
- transfer display binding document to yaml format.
- add mt8195 display device binding.
- allow commands to be sent during video mode.
- add wait_for_event for crtc disable by cmdq.
tegra:
- YUV format support
rcar-du:
- LVDS support for M3-W+ (R8A77961)
exynos:
- BGR pixel format for FIMD device"
* tag 'drm-next-2022-03-24' of git://anongit.freedesktop.org/drm/drm: (1529 commits)
drm/i915/display: Do not re-enable PSR after it was marked as not reliable
drm/i915/display: Fix HPD short pulse handling for eDP
drm/amdgpu: Use drm_mode_copy()
drm/radeon: Use drm_mode_copy()
drm/amdgpu: Use ternary operator in `vcn_v1_0_start()`
drm/amdgpu: Remove pointless on stack mode copies
drm/amd/pm: fix indenting in __smu_cmn_reg_print_error()
drm/amdgpu/dc: fix typos in comments
drm/amdgpu: fix typos in comments
drm/amd/pm: fix typos in comments
drm/amdgpu: Add stolen reserved memory for MI25 SRIOV.
drm/amdgpu: Merge get_reserved_allocation to get_vbios_allocations.
drm/amdkfd: evict svm bo worker handle error
drm/amdgpu/vcn: fix vcn ring test failure in igt reload test
drm/amdgpu: only allow secure submission on rings which support that
drm/amdgpu: fixed the warnings reported by kernel test robot
drm/amd/display: 3.2.177
drm/amd/display: [FW Promotion] Release 0.0.108.0
drm/amd/display: Add save/restore PANEL_PWRSEQ_REF_DIV2
drm/amd/display: Wait for hubp read line for Pollock
...
commit f86c3ed559 ("drm/mgag200: Split PLL setup into compute and
update functions") introduced a regression for g200wb and g200ew.
The PLLs are not set up properly, and VGA screen stays
black, or displays "out of range" message.
MGA1064_WB_PIX_PLLC_N/M/P was mistakenly replaced with
MGA1064_PIX_PLLC_N/M/P which have different addresses.
Patch tested on a Dell T310 with g200wb
Fixes: f86c3ed559 ("drm/mgag200: Split PLL setup into compute and update functions")
Cc: stable@vger.kernel.org
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308174321.225606-1-jfalempe@redhat.com
drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.
Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.
Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/686ec871-e77f-c230-22e5-9e3bb80f064a@linux.intel.com
Cross-subsystem Changes:
------------------------
dma-buf:
- dma-buf-map: Rename to iosys-map (Lucas)
Core Changes:
-------------
drm:
- Always include the debugfs_entry in drm_crtc (Ville)
- Add orientation quirk for GPD Win Max (Anisse)
Driver Changes:
---------------
gvt:
- Constify some pointers. (Rikard Falkeborn)
- Use list_entry to access list members. (Guenter Roeck)
- Fix cmd parser error for Passmark9. (Zhenyu Wang)
i915:
- Various clean-ups including headers and removing unused and unnecessary stuff\
(Jani, Hans, Andy, Ville)
- Cleaning up on our registers definitions i915_reg.h (Matt)
- More multi-FBC refactoring (Ville)
- Baytrail backlight fix (Hans)
- DG1 OPROM read through SPI controller (Clint)
- ADL-N platform enabling (Tejas)
- Fix slab-out-of-bounds access (Jani)
- Add opregion mailbox #5 support for possible EDID override (Anisse)
- Fix possible NULL dereferences (Harish)
- Updates and fixes around display voltage swing values (Clint, Jose)
- Fix RPM wekeref on PXP code (Juston)
- Many register definitions clean-up, including planes registers (Ville)
- More conversion towards display version over the old gen (Madhumitha, Ville)
- DP MST ESI handling improvements (Jani)
- drm device based logging conversions (Jani)
- Prevent divide by zero (Dan)
- Introduce ilk_pch_pre_enable for complete modeset abstraction (Ville)
- Async flip optimization for DG2 (Stanislav)
- Multiple DSC and bigjoiner fixes and improvements (Ville)
- Fix ADL-P TypeC Phy ready status readout (Imre)
- Fix up DP DFP 4:2:0 handling more display related fixes (Ville)
- Display M/N cleanup (Ville)
- Switch to use VGA definitions from video/vga.h (Jani)
- Fixes and improvements to abstract CPU architecture (Lucas)
- Disable unsused power wells left enabled by BIOS (Imre)
- Allow !join_mbus cases for adlp+ dbuf configuration (Ville)
- Populate pipe dbuf slices more accurately during readout (Ville)
- Workaround broken BIOS DBUF configuration on TGL/RKL (Ville)
- Fix trailing semicolon (Lucas)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YgKFLmCgpv4vQEa1@intel.com
Rename struct dma_buf_map to struct iosys_map and corresponding APIs.
Over time dma-buf-map grew up to more functionality than the one used by
dma-buf: in fact it's just a shim layer to abstract system memory, that
can be accessed via regular load and store, from IO memory that needs to
be acessed via arch helpers.
The idea is to extend this API so it can fulfill other needs, internal
to a single driver. Example: in the i915 driver it's desired to share
the implementation for integrated graphics, which uses mostly system
memory, with discrete graphics, which may need to access IO memory.
The conversion was mostly done with the following semantic patch:
@r1@
@@
- struct dma_buf_map
+ struct iosys_map
@r2@
@@
(
- DMA_BUF_MAP_INIT_VADDR
+ IOSYS_MAP_INIT_VADDR
|
- dma_buf_map_set_vaddr
+ iosys_map_set_vaddr
|
- dma_buf_map_set_vaddr_iomem
+ iosys_map_set_vaddr_iomem
|
- dma_buf_map_is_equal
+ iosys_map_is_equal
|
- dma_buf_map_is_null
+ iosys_map_is_null
|
- dma_buf_map_is_set
+ iosys_map_is_set
|
- dma_buf_map_clear
+ iosys_map_clear
|
- dma_buf_map_memcpy_to
+ iosys_map_memcpy_to
|
- dma_buf_map_incr
+ iosys_map_incr
)
@@
@@
- #include <linux/dma-buf-map.h>
+ #include <linux/iosys-map.h>
Then some files had their includes adjusted and some comments were
update to remove mentions to dma-buf-map.
Since this is not specific to dma-buf anymore, move the documentation to
the "Bus-Independent Device Accesses" section.
v2:
- Squash patches
v3:
- Fix wrong removal of dma-buf.h from MAINTAINERS
- Move documentation from dma-buf.rst to device-io.rst
v4:
- Change documentation title and level
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204170541.829227-1-lucas.demarchi@intel.com
On some servers with MGA G200_SE_A (rev 42), booting with Legacy BIOS,
the hardware hangs when using kdump and kexec into the kdump kernel.
This happens when the uncompress code tries to write "Decompressing Linux"
to the VGA Console.
It can be reproduced by writing to the VGA console (0xB8000) after
booting to graphic mode, it generates the following error:
kernel:NMI: PCI system error (SERR) for reason a0 on CPU 0.
kernel:Dazed and confused, but trying to continue
The root cause is the configuration of the MGA GCTL6 register
According to the GCTL6 register documentation:
bit 0 is gcgrmode:
0: Enables alpha mode, and the character generator addressing system is
activated.
1: Enables graphics mode, and the character addressing system is not
used.
bit 1 is chainodd even:
0: The A0 signal of the memory address bus is used during system memory
addressing.
1: Allows A0 to be replaced by either the A16 signal of the system
address (ifmemmapsl is ‘00’), or by the hpgoddev (MISC<5>, odd/even
page select) field, described on page 3-294).
bit 3-2 are memmapsl:
Memory map select bits 1 and 0. VGA.
These bits select where the video memory is mapped, as shown below:
00 => A0000h - BFFFFh
01 => A0000h - AFFFFh
10 => B0000h - B7FFFh
11 => B8000h - BFFFFh
bit 7-4 are reserved.
Current code set it to 0x05 => memmapsl to b01 => 0xa0000 (graphic mode)
But on x86, the VGA console is at 0xb8000 (text mode)
In arch/x86/boot/compressed/misc.c debug strings are written to 0xb8000
As the driver doesn't use this mapping at 0xa0000, it is safe to set it to
0xb8000 instead, to avoid kernel hang on G200_SE_A rev42, with kexec/kdump.
Thus changing the value 0x05 to 0x0d
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119102905.1194787-1-jfalempe@redhat.com
The "nomodeset" kernel cmdline parameter is handled by the vgacon driver
but the exported vgacon_text_force() symbol is only used by DRM drivers.
It makes much more sense for the parameter logic to be in the subsystem
of the drivers that are making use of it.
Let's move the vgacon_text_force() function and related logic to the DRM
subsystem. While doing that, rename it to drm_firmware_drivers_only() and
make it return true if "nomodeset" was used and false otherwise. This is
a better description of the condition that the drivers are testing for.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211112133230.1595307-4-javierm@redhat.com
Move all PLL compute and update functions into mgag200_pll.c. No
functional changes to the rsp algorithms.
Introduce struct mgag200_pll and mgag200_pll_funcs. The data strutures
abstract the details of each revision's PLL. Perform calls to compute
and update functionality via function pointers. Init the PLL once as
part of the driver initialization.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714142240.21979-11-tzimmermann@suse.de
The fields in struct mgag200_pll_values currently hold the bits of
each register. Store the PLL values instead and let the PLL-update
code figure out the bits for each register.
Until now, the compute function either stored plain values or register
bits in struct mgag200_pll_values. The rsp update function used the
values as-is. This made it very hard to correctly interpret the stored
values (e.g., for logging or debugging). With the cleanup, the stored
values now have a clear meaning.
v2:
* add a bit more context in the commit message (Sam)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714142240.21979-7-tzimmermann@suse.de
The S parameter is controls the loop filter bandwidth when programming
the PLL. It's currently stored as part of P (i.e., the clock divider.)
Add a separate variable for S prepares the PLL code for further
refactoring. The value of s is currently 0, so it has not yet an effect
on the programming.
v2:
* add a note on the current value of s to commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714142240.21979-6-tzimmermann@suse.de
The _set_plls() functions compute a pixel clock's PLL values
and program the hardware accordingly. This happens during atomic
commits.
For atomic modesetting, it's better to separate computation and
programming from each other. This will allow to compute the PLL
value during atomic checks and catch unsupported modes early.
Split the PLL setup into a compute and an update functions, and
call them one after the other. Computed PLL values are store in
struct mgag200_pll_values. There are four parameters for the PLL,
m, n, p and s. Every compute function stores a value for each
of these parameters, and the rsp update function makes the register
bits from them. The values stored by the compute function are
either plain values or register bits. An additional change is
required to always store plain values.
No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714142240.21979-5-tzimmermann@suse.de
