[Why]
Immediate flip can be enabled dynamically and has higher BW requirements
when validating which voltage mode to use.
If we validate when it's not set then potentially DCFCLK will be too low
and we will underflow.
[How]
DM always requires support so always require it as part of DML input
parameters.
This can't be enabled unconditionally on older ASIC because it blocks
some expected modes so only target DCN3.1 for now.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
PSR_STATE2b was introduced on DMCUB side, but not on the driver side,
which caused convert_psr_state helper function to return
PSR_STATE_INVALID. That caused visual lagging during state transition.
[how]
Add PSR_STATE2b to dc_psr_state and convert_psr_state
Reviewed-by: Wyatt Wood <Wyatt.Wood@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Prefetch BW calculated is lower than the DML reference because of a
porting error that's excluding cursor and row bandwidth from the
pixel data bandwidth.
[How]
Change the dml_max4 to dml_max3 and include cursor and row bandwidth
in the same calculation as the rest of the pixel data during vactive.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Calculation of scaling ratio can result in a crash due to zero'd src or
dst plane rects.
[How]
Validate that src and dst rects are valid before using for scaling
calculations.
Reviewed-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hardware team has recommended to generically hard code this register to
0xFF as part of the effort to eventually remove this control. However
we set it to 0xF instead.
This causes 4 of audio 8ch to be muted.
Reviewed-by: Ariel Bernstein <eric.bernstein@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly plugging and unplugging a DP sink, detection link
training can be mistakenly skipped.
This is due to the hotplug processing occurring before the
encoder assignment logic has had a chance to process the removal
of a stream. The encoder that would be used for detection link
training is then erroneously reported as already in use and
detection link training is skipped.
[How]
During hot plug processing, only determine a link encoder to be
unavailable for a particular link if it has been assigned to a
different link.
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When copying a stream, the encoder assigned to it is copied too.
Encoder assignment should only happen when executing the encoder
assignment function link_encs_assign().
[How]
Clear the link encoder pointer for copied stream.
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
When system boots in headless mode, connecting a 4k display creates a
null pointer dereference due to hubp for a certain plane being null.
Add a condition to check for null hubp before dereferencing it.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE legacy optimization path isn't well tested under new DC optimization
flow which can result in underflow occuring when initializing X11 on
Carrizo.
[How]
Retain the legacy optimization flow for DCE and keep the new one for DCN
to satisfy optimizations being correctly applied for ASIC that can
support it.
Fixes: 34316c1e56 ("drm/amd/display: Optimize bandwidth on following fast update")
Reported-by: Tom St Denis <tom.stdenis@amd.com>
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Got Werror when building with Clang-13:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dpia.c:195:2:
error: variable 'ts' is used uninitialized whenever switch default is
taken [-Werror,-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dpia.c:200:9:
note: uninitialized use occurs here
return ts;
^~
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dpia.c:180:2:
note: variable 'ts' is declared here
enum dpia_set_config_ts ts;
^
1 error generated.
Fix it.
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable result is being initialized with a value that is never
read, it is being updated immediately afterwards in both branches
of an if statement. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Overriding link setting inside override_training_settings
result in fallback link settings being ignored. This can
potentially cause link training to always fail and consequently
result in an infinite loop of link training to occur in
dp_verify_link_cap during detection.
[How]
Since preferred link settings are already considered inside
decide_link_settings, skip the check in override_training_settings
to avoid infinite link training loops.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DIB_BE_CNTL<i>.DIG_HPD_SELECT selects the HPD block being used
by the display endpoint assigned to DIG<i>. In the case of USB4
display endpoints, no physical HPD block is assigned.
[How]
Setting DIB_BE_CNTL<i>.DIG_HPD_SELECT to 5 indicates that no HPD
is assigned to a display endpoint. Firmware decrements the
HPD_SELECT value by 1 before writing it to the register.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To process SET_CONFIG transactions with DMUB using inbox1 and
outbox1 mail boxes.
[How]
1) DMUB posts SET_CONFIG reply as an Outbox1 message of type
DMUB_OUT_CMD__SET_CONFIG_REPLY.
2) The dmub async to sync mechanism for AUX is modified to accommodate
SET_CONFIG commands for both command issue and reply code paths.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jude Shih <shenshih@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To process SET_CONFIG transactions with DMUB using inbox1 and
outbox1 mail boxes.
[How]
1) Added inbox1 DPIA command subtype DMUB_CMD__DPIA_SET_CONFIG_ACCESS to
issue SET_CONFIG command to DMUB in dc_process_dmub_set_config_async().
DMUB processes the command with DPIA sends reply back immediately or
in an outbox1 message triggering an outbox1 interrupt to driver.
2) DMUB posts SET_CONFIG reply as an Outbox1 message of type
DMUB_OUT_CMD__SET_CONFIG_REPLY.
3) The dmub async to sync mechanism for AUX is modified to accommodate
SET_CONFIG commands for both command issue and reply code paths.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Training settings need to be applied to DPIA link at start of each
training loop. Note: FEC readiness should be configured before link
training while FEC enablement should be configured once training is
complete.
[How]
- Implement DPIA link configuration function.
- Account for dynamically assigned link encoders during link
configuration.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Training of DPIA link differs enough from that of conventional
DP link to warrant a separate implementation.
[How]
- Implement top-level of DPIA training loop.
- Make functions shared between DP and DPIA link training "public".
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To add support for HPD & HPD RX interrupt handling for USB4 DPIA in
YELLOW_CARP_B0. USB4 DPIA HPD & HPD RX interrupts are issued from DMUB to
driver as a outbox1 message.
[HOW]
1) Created get_link_index_from_dpia_port_index() to retrieve link index
from dpia port index for HPD & HPD RX dmub notifications.
2) Added DMUB HPD & HPD RX handling in dmub_srv_stat_get_notification().
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To enable dc links for USB4 DPIA ports and AUX command tunneling
for YELLOW_CARP_B0.
[HOW]
1) Created dc links for all USB4 DPIA ports in create_links().
dc_link_construct() implementation is split for legacy DDC and DPIAs.
As usb4 has no ddc, ddc->ddc_pin will be set to NULL for its dc link
and this parameter will be used to identify the dc links as DPIA. The
dc link for DPIA is further to be enhanced with implementation for link
encoder and link initialization.
2) usb4_dpia_count in struct resource_pool will be initialized to 4 in
dcn31_resource_construct() if the DCN is YELLOW_CARP_B0.
3) Enabled DMUB AUX via outbox for YELLOW_CARP_B0.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
