As "dcn3_1_soc", "dcn3_15_soc", and "dcn3_16_soc" are not used outside
of their corresponding "dcn3*_fpu.c", make them static and remove their
extern declaration.
Fixes: 26f4712aed ("drm/amd/display: move FPU related code from dcn31 to dml/dcn31 folder")
Fixes: fa896297b3 ("drm/amd/display: move FPU related code from dcn315 to dml/dcn31 folder")
Fixes: 3f8951cc12 ("drm/amd/display: move FPU related code from dcn316 to dml/dcn31 folder")
Signed-off-by: Magali Lemes <magalilemes00@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Preparation to enable run time initialization of register offsets to add
dc_context to the link_enc_create callback. This is needed to get the
dc_ctx handle where register offset initialization routine is called.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Access violation occurs when swapping between HDMI and FRL monitors
because we're missing the immediate_disable_crtc callback and it's
required for the DCN314 clk manager.
[How]
Update the table to match the DCN31 optc functions for ones that
should be the same:
- immediate_disable_crtc
- configure_crc
Reviewed-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Many lines of code in dcn31_resource_construct are wrapped by DC_FP
macro to protect FPU operations; however, there is no FPU in this
region. Therefore, just remove the wrapper for clarity.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move remaining FPU code to DML folder that caused compilation error for
powerpc. This patch depends on [1] to prevent the error below:
/gcc-11.3.0-nolibc/powerpc64-linux/bin/powerpc64-linux-ld: drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.o uses hard float, drivers/gpu/drm/amd/amdgpu/../display/dc/dcn31/dcn31_resource.o uses soft float
/gcc-11.3.0-nolibc/powerpc64-linux/bin/powerpc64-linux-ld: failed to merge target specific data of file drivers/gpu/drm/amd/amdgpu/../display/dc/dcn31/dcn31_resource.o
/gcc-11.3.0-nolibc/powerpc64-linux/bin/powerpc64-linux-ld: drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.o uses hard float, drivers/gpu/drm/amd/amdgpu/../display/dc/dcn315/dcn315_resource.o uses soft float
/gcc-11.3.0-nolibc/powerpc64-linux/bin/powerpc64-linux-ld: failed to merge target specific data of file drivers/gpu/drm/amd/amdgpu/../display/dc/dcn315/dcn315_resource.o
/gcc-11.3.0-nolibc/powerpc64-linux/bin/powerpc64-linux-ld: drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.o uses hard float, drivers/gpu/drm/amd/amdgpu/../display/dc/dcn316/dcn316_resource.o uses soft float
/gcc-11.3.0-nolibc/powerpc64-linux/bin/powerpc64-linux-ld: failed to merge target specific data of file drivers/gpu/drm/amd/amdgpu/../display/dc/dcn316/dcn316_resource.o
[1] https://lore.kernel.org/amd-gfx/20220716195144.342960-1-mwen@igalia.com/
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Although dcn31_update_soc_for_wm_a() is only called in dml/dcn31/dcn31_fpu by
dc->res_pool->funcs->update_soc_for_wm_a(dc, context), it's declared in
dcn31_resource that is not FPU protected. Move this function to dcn31_fpu
file as part of the work to isolate FPU code.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Several issues were discovered that caused link
training to fail when an LTTPR device is
connected downstream for the fixed VS sequence.
[How]
The following were added:
- workaround to configure AUX timeout
for fixed VS sequence
- additional delay before disabling
fixed VS intercept
- detection of fixed VS deadlock state and
performing DPCD sequence to recover
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some scenarios it is possible for the encoder assignment module to be
set to "transient" mode even though there are no new encoder
assignments.
This can lead to incorrect results when querying encoder assignment,
which in turn can cause incorrect displays to be manipulated.
[How]
Only allow encoder assignment to be in transient mode of operation when
there are valid new encoder assignments.
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For panels with pixel clock > 1200MHz that require ODM
in pre-OS, when driver is disabled in OS, odm is enabled.
Upon driver enablement, corruption is seen if
odm was originally enabled. DP_PIXEL_COMBINE and
pixelclk must be programmed prior to programming the
optc-odm registers. However, eDP displays aren't blanked
prior to initializing odm in this case.
[How]
Upon driver enablement, check whether odm is enabled,
if so, blank eDP prior to programming optc-odm
registers.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The existing calculations in DCN3.1 were placeholder and need to be
replaced with HW team approved calculations.
[How]
The new calculations add new parameters to the bounding box and pipe
params - VblankNom and the bounding box default.
The placeholder calculations are dropped from DCN3.1 in the meantime
while we work out hardware approved replacements.
Also fix a bug where we wipe out other register contents with a REG_SET
instead of a REG_UPDATE for the register we were programming the
min_dst_y_next_start_optimized.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Revised validation logic when marking for seamless boot. Init resources
accordingly when Pre-OS has ODM enabled. Reset ODM when transitioning
Pre-OS odm to Post-OS non-odm to avoid corruption. Apply logic to set
odm accordingly upon commit.
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Implements DTB ref clock switching with reg key default to OFF.
Refactors dccg DTBCLK logic to not store redundant state information
dccg. Also removes duplicated functions that should be inherited from
other dcn versions.
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
ref_dtbclk value is assigned in clk_mgr_construct,
but the clks struct is cleared in init_clocks.
Make sure to restore the value or we will get
0 value for ref_dtbclk in DCN31.
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMUB Outbox0 read/write pointer not sync after resumed from S4.
And that caused old traces were sent to outbox.
[How]
Disable DMUB Outbox0 interrupt
and clear DMUB Outbox0 read/write pointer when resumes from S4.
And then enable Outbox0 interrupt before starts DMCUB.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dmub read AUX_DPHY_RX_CONTROL0 from Golden Setting Table,
but driver will set it to default value 0x103d1110, which
causes issue in some case
[How]
Remove the driver code, use the value set by dmub in
dp_aux_init
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Sherry Wang <YAO.WANG1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
From [1], I realized two other calls to dcn30 code are associated with
FPU operations and are not protected by DC_FP_* macros:
* dcn30_populate_dml_writeback_from_context()
* dcn30_set_mcif_arb_params()
So, since FPU-associated code is not fully isolated in dcn30, and
dcn3.1.x reuses them, let's wrap their calls properly.
Note: this patch complements the fix from [1].
[1] https://lore.kernel.org/amd-gfx/20220329082957.1662655-1-chandan.vurdigerenataraj@amd.com/
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 863fa85e6a.
While we were testing DCN3.1 with a hub, we noticed that only one of 2
connected displays lights up when using some specific display
resolution. In summary, this was the setup:
1. Displays:
* Sharp LQ156M1JW26 (eDP): 1080@240
* BENQ SW320 (DP): 4k@60
* BENQ EX3203R (DP): 4k@60
2. Hub: Club3D CSV-7300
3. ASIC: DCN3.1
After bisecting this issue, we figured out the commit mentioned above
introduced this issue. We are investigating why this patch introduced
this regression, but we need to revert it for now.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Mark Broadworth <Mark.Broadworth@amd.com>
Cc: Michael Strauss <michael.strauss@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Implement changes to transition from Pre-OS odm to
Post-OS odm support. Seamless boot case is also
considered.
[HOW]
Revised validation logic when marking for seamless
boot. Init resources accordingly when Pre-OS has
odm enabled. Reset odm and det size when transitioning
Pre-OS odm to Post-OS non-odm to avoid corruption.
Apply logic to set odm accordingly upon commit.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Duncan Ma <Duncan.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Z10 and S0i3 have some shared path. Previous code clean up ,
incorrectly removed these pointers, which breaks s0i3 restore
[How]
Do not clear the function pointers based on Z10 disable.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In init_hw() we call init_pipes() before enabling power gating.
init_pipes() tries to power gate dsc but it may fail because
required force-ons are not released yet.
As a result with dsc config the following errors observed on resume:
"REG_WAIT timeout 1us * 1000 tries - dcn20_dsc_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_dpp_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_hubp_pg_control"
[How]
Move enable_power_gating_plane() before init_pipes() in init_hw()
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Creates FPU files in dml/dcn31 folder to centralize FPU operations
from 3.1x drivers and moves all FPU-associated code from dcn31 driver
to there. It includes the struct _vcs_dpi_ip_params_st and
_vcs_dpi_soc_bounding_box_st and functions:
- dcn31_calculate_wm_and_dlg_fp()
- dcn31_update_bw_bounding_box()
adding dc_assert_fp_enabled to them and drop DC_FP_START/END inside
functions that was moved to dml folder, as required.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we enter FREESYNC_STATE_VIDEO, we want to use the extra vblank
portion to enter zstate if possible.
[how]
When we enter freesync, a full update is triggered and the new vtotal
with extra lines is passed to dml in a stream update. The time gained
from extra vblank lines is calculated in microseconds. We allow zstate
entry if the time gained is greater than 5 ms, which is the current
policy. Furthermore, an optimized value for min_dst_y_next_start is
calculated and written to its register. When exiting freesync, another
full update is triggered and default values are restored.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It changed since dcn30 but the hubbub31 constructor hasn't been
modified to reflect this.
[How]
Update the value in the constructor to 0x6 so we're checking the right
bits for p-state allow.
It worked before by accident, but can falsely assert 0 depending on HW
state transitions. The most frequent of which appears to be when
all pipes turn off during IGT tests.
Cc: Harry Wentland <harry.wentland@amd.com>
Fixes: e7031d8258 ("drm/amd/display: Add pstate verification and recovery for DCN31")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To debug when p-state is being blocked and avoid PMFW hangs when
it does occur.
[How]
Re-use the DCN10 hardware sequencer by adding a new interface for
verifying p-state high on the hubbub. The interface is mostly the
same as the DCN10 interface, but the bit definitions have changed for
the debug bus.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move parts of dcn20 code that uses FPU to dml folder. It aims to isolate
FPU operations as described by series:
drm/amd/display: Introduce FPU directory inside DC
https://patchwork.freedesktop.org/series/93042/
This patch moves the following functions from dcn20_resource to
dml/dcn20_fpu and calls of public functions in dcn20_resource are
wrapped by DC_FP_START/END():
- void dcn20_populate_dml_writeback_from_context
- static bool is_dtbclk_required()
- static enum dcn_zstate_support_state()
- void dcn20_calculate_dlg_params()
- static void swizzle_to_dml_params()
- int dcn20_populate_dml_pipes_from_context()
- void dcn20_calculate_wm()
- void dcn20_cap_soc_clocks()
- void dcn20_update_bounding_box()
- void dcn20_patch_bounding_box()
- bool dcn20_validate_bandwidth_fp()
This movement also affects dcn21/30/31, as dcn20_calculate_dlg_params()
is used by them. For this reason, I included dcn20_fpu headers in
dcn20_resource headers to make dcn20_calculate_dlg_params() visible to
dcn21/30/31.
Three new functions are created to isolate well-delimited FPU
operations:
- void dcn20_fpu_set_wb_arb_params(): set cli_watermark,
pstate_watermark and time_per_pixel from wb_arb_params (struct
mcif_arb_params), since those uses FPU operations on double types:
WritebackUrgentWatermark, WritebackDRAMClockChangeWatermark, '16.0'.
- void dcn20_fpu_set_wm_ranges(): set min_fill_clk_mhz and
max_fill_clk_mhz involves FPU calcs on dram_speed_mts (double type);
- void dcn20_fpu_adjust_dppclk(): adjust operation on RequiredDPPCLK
that is a double.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Calculations differ with HostVM enabled/disabled, causing underflow in
configs with high refresh displays + scaling due to lower available BW
[HOW]
Check riommu_active in order to pass correct HostVM enablement to DML
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
